PATCH: Fix Jmicron support
Prior to 2.6.18rc1 you could install with devices on a JMicron chipset using the "all-generic-ide" option. As of this kernel the AHCI driver grabs the controller and rams it into AHCI mode losing the PATA ports and making CD drives and the like vanish. The all-generic-ide option fails because the AHCI driver grabbed the PCI device and reconfigured it.
To fix this three things are needed.
#1 We must put the chip into dual function mode
#2 The AHCI driver must grab only function 0 (already in your rc1 tree) #3 Something must grab the PATA ports
The attached patch is the minimal risk edition of this. It puts the chip into dual function mode so that AHCI will grab the SATA ports without losing the PATA ports. To keep the risk as low as possible the third patch adds the PCI identifiers for the PATA port and the FN check to the ide-generic driver. There is a more featured jmicron driver on its way but that adds risk and the ide-generic support is sufficient to install and run a system.
The actual chip setup done by the quirk is the precise setup recommended by the vendor.
(The JMB368 appears only in the ide-generic entry as it has no AHCI so does not need the quirk)
drivers/ide/pci/generic.c +8 -0
@@ -211,6 +211,9 @@ dev->device == PCI_DEVICE_ID_OPTI_82C558 && (!(PCI_FUNC(dev->devfn) & 1))) goto out; + +if (dev->vendor ==PCI_VENDOR_ID_JMICRON &&PCI_FUNC (dev->devfn) !=1 ) + goto out;pci_read_config_word (dev,PCI_COMMAND , &command);if (!(command &PCI_COMMAND_IO )) {
@@ -239,6 +242,11 @@ { PCI_VENDOR_ID_TOSHIBA,PCI_DEVICE_ID_TOSHIBA_PICCOLO_1, PCI_ANY_ID, PCI_ANY_ID, 0, 0, 12}, { PCI_VENDOR_ID_TOSHIBA,PCI_DEVICE_ID_TOSHIBA_PICCOLO_2, PCI_ANY_ID, PCI_ANY_ID, 0, 0, 13}, { PCI_VENDOR_ID_NETCELL,PCI_DEVICE_ID_REVOLUTION, PCI_ANY_ID, PCI_ANY_ID, 0, 0, 14}, + { PCI_VENDOR_ID_JMICRON, PCI_DEVICE_ID_JMICRON_JMB361, PCI_ANY_ID, PCI_ANY_ID, 0, 0, 15}, + { PCI_VENDOR_ID_JMICRON, PCI_DEVICE_ID_JMICRON_JMB363, PCI_ANY_ID, PCI_ANY_ID, 0, 0, 16}, + { PCI_VENDOR_ID_JMICRON, PCI_DEVICE_ID_JMICRON_JMB365, PCI_ANY_ID, PCI_ANY_ID, 0, 0, 17}, + { PCI_VENDOR_ID_JMICRON, PCI_DEVICE_ID_JMICRON_JMB366, PCI_ANY_ID, PCI_ANY_ID, 0, 0, 18}, + { PCI_VENDOR_ID_JMICRON, PCI_DEVICE_ID_JMICRON_JMB368, PCI_ANY_ID, PCI_ANY_ID, 0, 0, 19},/* Must come last. If you add entries adjust this table appropriately and the init_one code */ { PCI_ANY_ID, PCI_ANY_ID, PCI_ANY_ID, PCI_ANY_ID, PCI_CLASS_STORAGE_IDE << 8, 0xFFFFFF00UL, 0}, { 0, },
drivers/pci/quirks.c +49 -0
55 lines not on this page · raw message
Quoted 3 lines · Alan Cox
+ * If we are using libata we can drive this chip proeprly but must
+ * do this early on to make the additional device appear during
+ * the PCI scanning.
"properly"
Quoted 9 lines
drivers/pci/quirks.c +9
-0+static void __devinit quirk_jmicron_dualfn (struct pci_dev *pdev) +{ +u32 conf; +u8 hdr; + +/* Only poke fn 0 */ +if (PCI_FUNC (pdev->devfn)) +return ; +
drivers/pci/quirks.c line 1203
Quoted 10 lines
drivers/pci/quirks.c +10
-0+switch (pdev->device) { +case PCI_DEVICE_ID_JMICRON_JMB365 : +case PCI_DEVICE_ID_JMICRON_JMB366 : +/* Redirect IDE second PATA port to the right spot */ +pci_read_config_dword (pdev,0x80 , &conf); + conf |= (1 <<24 ); +/* Fall through */ +pci_write_config_dword (pdev,0x80 , conf); +case PCI_DEVICE_ID_JMICRON_JMB361 : +case PCI_DEVICE_ID_JMICRON_JMB363 :
Wouldn't you want to put the fall throught comment after the pci_write? Took me a moment to parse it given its position
OG.
Quoted 21 lines · Alan Cox
Prior to 2.6.18rc1 you could install with devices on a JMicron chipset using the "all-generic-ide" option. As of this kernel the AHCI driver grabs the controller and rams it into AHCI mode losing the PATA ports and making CD drives and the like vanish. The all-generic-ide option fails because the AHCI driver grabbed the PCI device and reconfigured it.
To fix this three things are needed.
#1 We must put the chip into dual function mode
#2 The AHCI driver must grab only function 0 (already in your rc1 tree) #3 Something must grab the PATA portsThe attached patch is the minimal risk edition of this. It puts the chip into dual function mode so that AHCI will grab the SATA ports without losing the PATA ports. To keep the risk as low as possible the third patch adds the PCI identifiers for the PATA port and the FN check to the ide-generic driver. There is a more featured jmicron driver on its way but that adds risk and the ide-generic support is sufficient to install and run a system.
Quoted 7 lines
The actual chip setup done by the quirk is the precise setup recommended by the vendor.
(The JMB368 appears only in the ide-generic entry as it has no AHCI so does not need the quirk)
Signed-off-by Alan Cox <[email protected]>
ACK for 2.6.18-rc1-git
The AHCI bits are already in 2.6.18-rc1. The drivers/ide new-PCI-ID bits are arguably new features, but IMO obviously quite harmless.
Jeff