Skip to contentSkip to conversation

hotplug polling, take 3

PATCH New Tejun Heo 2 participants 7 messages Jul 17, 2006 – Jul 24, 2006

Subsystems (2)
SCSI libata
lore
Share & tools
lore

Tejun Heo

author
#0 lore raw

PATCH 1/1 hotplug polling, take 3

Hello, all.

This is the third take of hotplug polling patchset. As the name implies, this patchset implements hotplug by polling. Changes from the last take[L] are.

* updated to accomodate earlier fixes & updates

* hp-poll is automatically disabled if the port enters any of static powersave mode.

* hp-poll can be manually disabled by setting
libata.hotplug_polling_interval to zero.

This patchset is also available in the following git tree.

http://htj.dyndns.org/git/?p=libata-tj.git;a=shortlog;h=hp-poll
git://htj.dyndns.org/libata-tj hp-poll

Thanks.

--
tejun

[L] http://article.gmane.org/gmane.linux.ide/11862
[1] http://article.gmane.org/gmane.linux.ide/11966
[2] http://article.gmane.org/gmane.linux.ide/12001
[3] http://article.gmane.org/gmane.linux.ide/12002
[4] http://article.gmane.org/gmane.linux.ide/11870
[5] http://article.gmane.org/gmane.linux.ide/12138

author
#1 lore raw

PATCH 1/3 libata: implement hotplug by polling

This patch implements hotplug by polling - hp-poll. It is used for

* hotplug event detection on controllers which don't provide PHY status changed interrupt.

* hotplug event detection on disabled ports after reset failure. libata used to leave such ports in frozen state to protect the system from malfunctioning controller/device. With hp-poll, hotplug events no such ports are watched safely by polling, such that removing/replacing the malfunctioning device triggers EH retry on the port.

There are three port ops for hp-poll - hp_poll_activate, hp_poll, hp_poll_deactivate. Only hp_poll is mandatory for hp-poll to work. This patch also implements SATA standard polling callbacks which poll SError.N/X bits - sata_std_hp_poll_activate() and sata_std_hp_poll().

By default, hp-poll is enabled only on disabled ports. If a LLD doesn't support hotplug interrupts but can poll for hotplug events, it should indicate it by setting ATA_FLAG_HP_POLLING which tells libata to turn on hp-poll by default.

Putting port into any static powersave mode or setting libata.hotplug_polling_interval to zero disables hp-poll.

Signed-off-by Tejun Heo <[email protected]>

---

 drivers/scsi/libata-core.c |   92 ++++++++++++++++++++++++++++
 drivers/scsi/libata-eh.c   |  143 +++++++++++++++++++++++++++++++++++++++++++-
 drivers/scsi/libata.h      |    5 ++
 include/linux/libata.h     |   10 +++
 4 files changed, 246 insertions(+), 4 deletions(-)

5cc3fdf67263ca76fc930ab9400a26fb637b18ae

drivers/scsi/libata-core.c +92 -0
index 9890387..f1db8d4 100644
@@ -3082,6 +3082,86 @@ void sata_std_set_powersave(struct ata_p
 }
 
 /**
+ *	sata_std_hp_poll_activate - standard SATA hotplug polling activation
+ *	@ap: the target ata_port
+ *
+ *	Activate SATA std hotplug polling.
+ *
+ *	LOCKING:
+ *	Kernel thread context (may sleep).
+ */
+void sata_std_hp_poll_activate(struct ata_port *ap)
+{
+	u32 serror, mask;
+
+	/* watch .X and, if not in dynamic powersave, .N */
+	mask = SERR_DEV_XCHG;
+	if (ata_ps_dynamic(ap->ps_state) == ATA_PS_NONE)
+		mask |= SERR_PHYRDY_CHG;
+
+	sata_scr_read(ap, SCR_ERROR, &serror);
+	serror &= mask;
+	if (serror)
+		sata_scr_write(ap, SCR_ERROR, serror);
+
+	ap->hp_poll_data = 0;
+}
+
+/**
+ *	sata_std_hp_poll - standard SATA hotplug polling callback
+ *	@ap: the target ata_port
+ *
+ *	Poll SError.N/X for hotplug event.  Hotplug event is triggered
+ *	only after PHY stays stable for at least one full polling
+ *	interval after the first event detection.
+ *
+ *	LOCKING:
+ *	spin_lock_irqsave(host_set lock)
+ *
+ *	RETURNS:
+ *	1 if hotplug event has occurred, 0 otherwise.
+ */
+int sata_std_hp_poll(struct ata_port *ap)
+{
+	unsigned long state = (unsigned long)ap->hp_poll_data;
+	u32 serror, mask;
+	int rc = 0;
+
+	/* watch .X and, if not in dynamic powersave, .N */
+	mask = SERR_DEV_XCHG;
+	if (ata_ps_dynamic(ap->ps_state) == ATA_PS_NONE)
+		mask |= SERR_PHYRDY_CHG;
+
+	sata_scr_read(ap, SCR_ERROR, &serror);
+	serror &= mask;
+
+	switch (state) {
+	case 0:
+		if (serror) {
+			/* PHY status could be bouncing crazy due to
+			 * faulty controller or device.  Don't fire
+			 * hotplug event till hotplug event stays
+			 * quiescent for one full polling interval.
+			 */
+			sata_scr_write(ap, SCR_ERROR, serror);
+			state = 1;
+		}
+		break;
+
+	case 1:
+		if (!serror)
+			rc = 1;
+		else
+			sata_scr_write(ap, SCR_ERROR, serror);
+		break;
+	}
+
+	ap->hp_poll_data = (void *)(unsigned long)state;
+
+	return rc;
+}
+
+/**
  *	ata_dev_same_device - Determine whether new ID matches configured device
  *	@dev: device to compare against
  *	@new_class: class of the new device

@@ -5798,6 +5878,7 @@ #endif
 	INIT_LIST_HEAD(&ap->eh_done_q);
 	init_waitqueue_head(&ap->eh_wait_q);
 	setup_timer(&ap->ps_timer, ata_ps_timer_worker, (unsigned long)ap);
+	INIT_LIST_HEAD(&ap->hp_poll_entry);
 
 	/* set cable type */
 	ap->cbl = ATA_CBL_NONE;

@@ -6119,6 +6200,9 @@ void ata_port_detach(struct ata_port *ap
 	list_del_init(&ap->all_ports_entry);
 	mutex_unlock(&ata_all_ports_mutex);
 
+	/* deactivate hotplug polling */
+	ata_hp_poll_deactivate(ap);
+
 	/* remove the associated SCSI host */
 	scsi_remove_host(ap->host);
 }

@@ -6365,6 +6449,12 @@ static int __init ata_init(void)
 
 static void __exit ata_exit(void)
 {
+	/* hp_poll_list gotta be empty by now and thus hp_poll_work
+	 * isn't rearming.
+	 */
+	WARN_ON(!list_empty(&hp_poll_list));
+	cancel_delayed_work(&hp_poll_work);
+
 	destroy_workqueue(ata_wq);
 	destroy_workqueue(ata_aux_wq);
 }

@@ -6504,6 +6594,8 @@ EXPORT_SYMBOL_GPL(sata_std_hips_timer_fn
 EXPORT_SYMBOL_GPL(sata_do_set_powersave);
 EXPORT_SYMBOL_GPL(sata_determine_hips_params);
 EXPORT_SYMBOL_GPL(sata_std_set_powersave);
+EXPORT_SYMBOL_GPL(sata_std_hp_poll_activate);
+EXPORT_SYMBOL_GPL(sata_std_hp_poll);
 EXPORT_SYMBOL_GPL(ata_dev_revalidate);
 EXPORT_SYMBOL_GPL(ata_dev_classify);
 EXPORT_SYMBOL_GPL(ata_dev_pair);
drivers/scsi/libata-eh.c +139 -4

194 lines not on this page · raw message

drivers/scsi/libata.h +5 -0
index 9e44f56..bc71b3f 100644
@@ -118,9 +118,14 @@ extern void ata_schedule_scsi_eh(struct 
 extern void ata_scsi_dev_rescan(void *data);
 
 /* libata-eh.c */
+extern struct list_head hp_poll_list;
+extern struct work_struct hp_poll_work;
+
 extern enum scsi_eh_timer_return ata_scsi_timed_out(struct scsi_cmnd *cmd);
 extern void ata_scsi_error(struct Scsi_Host *host);
 extern void ata_port_wait_eh(struct ata_port *ap);
 extern void ata_qc_schedule_eh(struct ata_queued_cmd *qc);
+extern void ata_hp_poll_activate(struct ata_port *ap);
+extern void ata_hp_poll_deactivate(struct ata_port *ap);
 
 #endif /* __LIBATA_H__ */
include/linux/libata.h +10 -0
index b8bee5f..39d6186 100644
@@ -164,6 +164,7 @@ enum {
 	ATA_FLAG_DEBUGMSG	= (1 << 13),
 	ATA_FLAG_HIPS		= (1 << 14), /* SATA host-initiated powersave */
 	ATA_FLAG_DIPS		= (1 << 15), /* SATA dev-initiated powersave */
+	ATA_FLAG_HP_POLLING	= (1 << 16), /* hotplug by polling */
 
 	/* The following flag belongs to ap->pflags but is kept in
 	 * ap->flags because it's referenced in many LLDs and will be

@@ -586,6 +587,9 @@ struct ata_port {
 
 	struct list_head	all_ports_entry;
 
+	struct list_head	hp_poll_entry;	/* hotplug poll list entry */
+	void			*hp_poll_data;
+
 	void			*private_data;
 
 	u8			sector_buf[ATA_SECT_SIZE]; /* owned by EH */

@@ -633,6 +637,10 @@ struct ata_port_operations {
 	void (*error_handler) (struct ata_port *ap);
 	void (*post_internal_cmd) (struct ata_queued_cmd *qc);
 
+	void (*hp_poll_activate) (struct ata_port *ap);
+	void (*hp_poll_deactivate) (struct ata_port *ap);
+	int (*hp_poll) (struct ata_port *ap);
+
 	irqreturn_t (*irq_handler)(int, void *, struct pt_regs *);
 	void (*irq_clear) (struct ata_port *);
 

@@ -702,6 +710,8 @@ extern int ata_std_prereset(struct ata_p
 extern int ata_std_softreset(struct ata_port *ap, unsigned int *classes);
 extern int sata_std_hardreset(struct ata_port *ap, unsigned int *class);
 extern void ata_std_postreset(struct ata_port *ap, unsigned int *classes);
+extern void sata_std_hp_poll_activate(struct ata_port *ap);
+extern int sata_std_hp_poll(struct ata_port *ap);
 extern unsigned long sata_do_hips_timer_fn(struct ata_port *ap, int seq,
 			u8 sctl_ipm, ata_update_sctl_spm_fn_t update_sctl_spm);
 extern unsigned long sata_std_hips_timer_fn(struct ata_port *ap, int seq);
Signature · 1 line
1.3.2
NAK
#2 lore raw

Re: [PATCH 1/3] libata: implement hotplug by polling

Quoted 22 lines · Tejun Heo

This patch implements hotplug by polling - hp-poll. It is used for

* hotplug event detection on controllers which don't provide PHY status changed interrupt.

* hotplug event detection on disabled ports after reset failure. libata used to leave such ports in frozen state to protect the system from malfunctioning controller/device. With hp-poll, hotplug events no such ports are watched safely by polling, such that removing/replacing the malfunctioning device triggers EH retry on the port.

There are three port ops for hp-poll - hp_poll_activate, hp_poll, hp_poll_deactivate. Only hp_poll is mandatory for hp-poll to work. This patch also implements SATA standard polling callbacks which poll SError.N/X bits - sata_std_hp_poll_activate() and sata_std_hp_poll().

By default, hp-poll is enabled only on disabled ports. If a LLD doesn't support hotplug interrupts but can poll for hotplug events, it should indicate it by setting ATA_FLAG_HP_POLLING which tells libata to turn on hp-poll by default.

Quoted 4 lines

Putting port into any static powersave mode or setting libata.hotplug_polling_interval to zero disables hp-poll.

Signed-off-by Tejun Heo <[email protected]>

NAK, there is no reason why a global poll list is needed. Simply having a struct workqueue in each schedule-able entity implicitly creates such a list. But regardless, this is another example of adding cross-controller synchronization, where none is needed.

If the worker fired per-host_set, then you could use an ata_port dynamic flag to indicate the poll-active ports, for the ata_hp_poll_worker() loop.

If the worker fires per-port, then no loop or mutex is needed at all. You could simply call the hp_poll hook.

include/linux/libata.h struct ata_port_operations { · line 646

Quoted 11 lines
include/linux/libata.h +4 -0
@@ -633,6 +637,10 @@ struct ata_port_operations {
 	void (*error_handler) (struct ata_port *ap);
 	void (*post_internal_cmd) (struct ata_queued_cmd *qc);
 
+	void (*hp_poll_activate) (struct ata_port *ap);
+	void (*hp_poll_deactivate) (struct ata_port *ap);
+	int (*hp_poll) (struct ata_port *ap);
+
 	irqreturn_t (*irq_handler)(int, void *, struct pt_regs *);
 	void (*irq_clear) (struct ata_port *);

All new hooks require at least a one-two sentence description in the DocBook docs, telling driver writers how to use them.

Jeff

author
#3 lore raw

Re: [PATCH 1/3] libata: implement hotplug by polling

Quoted 5 lines · Jeff Garzik

NAK, there is no reason why a global poll list is needed. Simply having a struct workqueue in each schedule-able entity implicitly creates such a list. But regardless, this is another example of adding cross-controller synchronization, where none is needed.

If the worker fired per-host_set, then you could use an ata_port dynamic flag to indicate the poll-active ports, for the ata_hp_poll_worker() loop.

If the worker fires per-port, then no loop or mutex is needed at all. You could simply call the hp_poll hook.

It was basically an optimization to reduce storage usage and spread all polling operations at least by polling interval even when there are many ports to poll. Cross-port synchronization aside, it's very simple too.
Hmm... I don't think it makes much difference either way though. I'll
convert to per-port workqueue + timer.

Quoted 4 lines
Quoted 4 lines
include/linux/libata.h +0 -0
@@ -633,6 +637,10 @@ struct ata_port_operations {
     void (*error_handler) (struct ata_port *ap);
     void (*post_internal_cmd) (struct ata_queued_cmd *qc);
Quoted 9 lines

include/linux/libata.h struct ata_port_operations { · line 646

Quoted 7 lines
include/linux/libata.h +4 -0
+    void (*hp_poll_activate) (struct ata_port *ap);
+    void (*hp_poll_deactivate) (struct ata_port *ap);
+    int (*hp_poll) (struct ata_port *ap);
+
     irqreturn_t (*irq_handler)(int, void *, struct pt_regs *);
     void (*irq_clear) (struct ata_port *);

All new hooks require at least a one-two sentence description in the DocBook docs, telling driver writers how to use them.

Will do.

Signature · 1 line
tejun
author
#4 lore raw

PATCH 2/3 libata: add hp-poll support to controllers with hotplug interrutps

In reply to Tejun Heo

This patch adds hp-poll support to the following drivers.

* ahci
* sata_nv (nf2 and c804 only)
* sata_sil
* sata_sil24

All the above controllers are capable of hotplug-by-interrupt and hp-poll will be used only for watching disabled ports.

Signed-off-by Tejun Heo <[email protected]>

---

 drivers/scsi/ahci.c       |    3 +++
 drivers/scsi/sata_nv.c    |    4 ++++
 drivers/scsi/sata_sil.c   |    2 ++
 drivers/scsi/sata_sil24.c |    3 +++
 4 files changed, 12 insertions(+), 0 deletions(-)

a7fe2cefdb1abfed43df9e12c3f05d885638b07b

drivers/scsi/ahci.c +3 -0
index b5fe19a..9fc2e57 100644
@@ -261,6 +261,9 @@ static const struct ata_port_operations 
 	.error_handler		= ahci_error_handler,
 	.post_internal_cmd	= ahci_post_internal_cmd,
 
+	.hp_poll_activate	= sata_std_hp_poll_activate,
+	.hp_poll		= sata_std_hp_poll,
+
 	.set_powersave		= ahci_set_powersave,
 
 	.port_start		= ahci_port_start,
drivers/scsi/sata_nv.c +4 -0
index 56da255..cdf3b65 100644
@@ -216,6 +216,8 @@ static const struct ata_port_operations 
 	.thaw			= nv_nf2_thaw,
 	.error_handler		= nv_error_handler,
 	.post_internal_cmd	= ata_bmdma_post_internal_cmd,
+	.hp_poll_activate	= sata_std_hp_poll_activate,
+	.hp_poll		= sata_std_hp_poll,
 	.data_xfer		= ata_pio_data_xfer,
 	.irq_handler		= nv_nf2_interrupt,
 	.irq_clear		= ata_bmdma_irq_clear,

@@ -243,6 +245,8 @@ static const struct ata_port_operations 
 	.thaw			= nv_ck804_thaw,
 	.error_handler		= nv_error_handler,
 	.post_internal_cmd	= ata_bmdma_post_internal_cmd,
+	.hp_poll_activate	= sata_std_hp_poll_activate,
+	.hp_poll		= sata_std_hp_poll,
 	.data_xfer		= ata_pio_data_xfer,
 	.irq_handler		= nv_ck804_interrupt,
 	.irq_clear		= ata_bmdma_irq_clear,
drivers/scsi/sata_sil.c +2 -0
index d0a8507..62deca4 100644
@@ -205,6 +205,8 @@ static const struct ata_port_operations 
 	.thaw			= sil_thaw,
 	.error_handler		= ata_bmdma_error_handler,
 	.post_internal_cmd	= ata_bmdma_post_internal_cmd,
+	.hp_poll_activate	= sata_std_hp_poll_activate,
+	.hp_poll		= sata_std_hp_poll,
 	.irq_handler		= sil_interrupt,
 	.irq_clear		= ata_bmdma_irq_clear,
 	.scr_read		= sil_scr_read,
drivers/scsi/sata_sil24.c +3 -0
index 0b5c3f1..0c1f082 100644
@@ -407,6 +407,9 @@ static const struct ata_port_operations 
 	.error_handler		= sil24_error_handler,
 	.post_internal_cmd	= sil24_post_internal_cmd,
 
+	.hp_poll_activate	= sata_std_hp_poll_activate,
+	.hp_poll		= sata_std_hp_poll,
+
 	.set_powersave		= sil24_set_powersave,
 
 	.port_start		= sil24_port_start,
Signature · 1 line
1.3.2
author
#5 lore raw

PATCH 3/3 libata: add hp-poll support to controllers without hotplug interrupts

In reply to Tejun Heo

This patch adds hp-poll support to the following drivers.

* sata_nv (generic)
* sata_sis
* sata_svw
* sata_uli
* sata_via
* sata_vsc

All the above drivers currently don't support hotplug interrupts (H/W restrictions or lack of doc/effort) and all hotplug operations should be done via hp-poll; thus, ATA_FLAG_HP_POLLING is set for these drivers.

Signed-off-by Tejun Heo <[email protected]>

---

 drivers/scsi/sata_nv.c  |    5 ++++-
 drivers/scsi/sata_sis.c |    5 ++++-
 drivers/scsi/sata_svw.c |    4 +++-
 drivers/scsi/sata_uli.c |    6 +++++-
 drivers/scsi/sata_vsc.c |    4 +++-
 5 files changed, 19 insertions(+), 5 deletions(-)

3a5e2866b5e69d113c1a7740969b9847ed41b545

drivers/scsi/sata_nv.c +4 -1
index cdf3b65..7bd9305 100644
@@ -189,6 +189,8 @@ static const struct ata_port_operations 
 	.thaw			= ata_bmdma_thaw,
 	.error_handler		= nv_error_handler,
 	.post_internal_cmd	= ata_bmdma_post_internal_cmd,
+	.hp_poll_activate	= sata_std_hp_poll_activate,
+	.hp_poll		= sata_std_hp_poll,
 	.data_xfer		= ata_pio_data_xfer,
 	.irq_handler		= nv_generic_interrupt,
 	.irq_clear		= ata_bmdma_irq_clear,

@@ -261,7 +263,8 @@ static struct ata_port_info nv_port_info
 	/* generic */
 	{
 		.sht		= &nv_sht,
-		.host_flags	= ATA_FLAG_SATA | ATA_FLAG_NO_LEGACY,
+		.host_flags	= ATA_FLAG_SATA | ATA_FLAG_NO_LEGACY |
+				  ATA_FLAG_HP_POLLING,
 		.pio_mask	= NV_PIO_MASK,
 		.mwdma_mask	= NV_MWDMA_MASK,
 		.udma_mask	= NV_UDMA_MASK,
drivers/scsi/sata_sis.c +4 -1
index ee6b5df..3b4bc5a 100644
@@ -117,6 +117,8 @@ static const struct ata_port_operations 
 	.thaw			= ata_bmdma_thaw,
 	.error_handler		= ata_bmdma_error_handler,
 	.post_internal_cmd	= ata_bmdma_post_internal_cmd,
+	.hp_poll_activate	= sata_std_hp_poll_activate,
+	.hp_poll		= sata_std_hp_poll,
 	.irq_handler		= ata_interrupt,
 	.irq_clear		= ata_bmdma_irq_clear,
 	.scr_read		= sis_scr_read,

@@ -128,7 +130,8 @@ static const struct ata_port_operations 
 
 static struct ata_port_info sis_port_info = {
 	.sht		= &sis_sht,
-	.host_flags	= ATA_FLAG_SATA | ATA_FLAG_NO_LEGACY,
+	.host_flags	= ATA_FLAG_SATA | ATA_FLAG_NO_LEGACY |
+			  ATA_FLAG_HP_POLLING,
 	.pio_mask	= 0x1f,
 	.mwdma_mask	= 0x7,
 	.udma_mask	= 0x7f,
drivers/scsi/sata_svw.c +3 -1
index 7d08580..9a446ad 100644
@@ -324,6 +324,8 @@ static const struct ata_port_operations 
 	.thaw			= ata_bmdma_thaw,
 	.error_handler		= ata_bmdma_error_handler,
 	.post_internal_cmd	= ata_bmdma_post_internal_cmd,
+	.hp_poll_activate	= sata_std_hp_poll_activate,
+	.hp_poll		= sata_std_hp_poll,
 	.irq_handler		= ata_interrupt,
 	.irq_clear		= ata_bmdma_irq_clear,
 	.scr_read		= k2_sata_scr_read,

@@ -424,7 +426,7 @@ static int k2_sata_init_one (struct pci_
 
 	probe_ent->sht = &k2_sata_sht;
 	probe_ent->host_flags = ATA_FLAG_SATA | ATA_FLAG_NO_LEGACY |
-				ATA_FLAG_MMIO;
+				ATA_FLAG_MMIO | ATA_FLAG_HP_POLLING;
 	probe_ent->port_ops = &k2_sata_ops;
 	probe_ent->n_ports = 4;
 	probe_ent->irq = pdev->irq;
drivers/scsi/sata_uli.c +5 -1
index 33cdb48..d3ab9ed 100644
@@ -115,6 +115,9 @@ static const struct ata_port_operations 
 	.error_handler		= ata_bmdma_error_handler,
 	.post_internal_cmd	= ata_bmdma_post_internal_cmd,
 
+	.hp_poll_activate	= sata_std_hp_poll_activate,
+	.hp_poll		= sata_std_hp_poll,
+
 	.irq_handler		= ata_interrupt,
 	.irq_clear		= ata_bmdma_irq_clear,
 

@@ -128,7 +131,8 @@ static const struct ata_port_operations 
 
 static struct ata_port_info uli_port_info = {
 	.sht            = &uli_sht,
-	.host_flags     = ATA_FLAG_SATA | ATA_FLAG_NO_LEGACY,
+	.host_flags     = ATA_FLAG_SATA | ATA_FLAG_NO_LEGACY |
+			  ATA_FLAG_HP_POLLING,
 	.pio_mask       = 0x1f,		/* pio0-4 */
 	.udma_mask      = 0x7f,		/* udma0-6 */
 	.port_ops       = &uli_ops,
drivers/scsi/sata_vsc.c +3 -1
index ad37871..d7da4c2 100644
@@ -302,6 +302,8 @@ static const struct ata_port_operations 
 	.thaw			= ata_bmdma_thaw,
 	.error_handler		= ata_bmdma_error_handler,
 	.post_internal_cmd	= ata_bmdma_post_internal_cmd,
+	.hp_poll_activate	= sata_std_hp_poll_activate,
+	.hp_poll		= sata_std_hp_poll,
 	.irq_handler		= vsc_sata_interrupt,
 	.irq_clear		= ata_bmdma_irq_clear,
 	.scr_read		= vsc_sata_scr_read,

@@ -396,7 +398,7 @@ static int __devinit vsc_sata_init_one (
 
 	probe_ent->sht = &vsc_sata_sht;
 	probe_ent->host_flags = ATA_FLAG_SATA | ATA_FLAG_NO_LEGACY |
-				ATA_FLAG_MMIO;
+				ATA_FLAG_MMIO | ATA_FLAG_HP_POLLING;
 	probe_ent->port_ops = &vsc_sata_ops;
 	probe_ent->n_ports = 4;
 	probe_ent->irq = pdev->irq;
Signature · 1 line
1.3.2
#6 lore raw

Re: [PATCH 3/3] libata: add hp-poll support to controllers without hotplug interrupts

ACK patches 2-3