ahci: update new users of new added functions

1 Use ahci_start_fis_rx(), ahci_port_spinup(), ahci_start_engine() in ahci_port_start()
2 Use ahci_stop_engine(), ahci_stop_fis_rx() in ahci_host_init()

---

 drivers/scsi/ahci.c |   50 ++++++++++++++++++++++
+---------------------------
 1 files changed, 23 insertions(+), 27 deletions(-)

9c57dea5678c608c5257ad2e6a363c52fd563ca8

index 50d0183..5e04ef4 100644
@@ -442,20 +442,20 @@ static int ahci_port_start(struct ata_po
 
        ap->private_data = pp;
 
-       if (hpriv->cap & HOST_CAP_64)
-               writel((pp->cmd_slot_dma >> 16) >> 16, port_mmio +

PORT_LST_ADDR_HI);
- writel(pp->cmd_slot_dma & 0xffffffff, port_mmio +
PORT_LST_ADDR);
- readl(port_mmio + PORT_LST_ADDR); /* flush */
-
- if (hpriv->cap & HOST_CAP_64)
- writel((pp->rx_fis_dma >> 16) >> 16, port_mmio +
PORT_FIS_ADDR_HI);

-       writel(pp->rx_fis_dma & 0xffffffff, port_mmio + PORT_FIS_ADDR);
-       readl(port_mmio + PORT_FIS_ADDR); /* flush */
+       /*

+ * Driver is setup; initialize the HBA
+ */
+ ahci_start_fis_rx(port_mmio, pp, hpriv);

- writel(PORT_CMD_ICC_ACTIVE | PORT_CMD_FIS_RX |
- PORT_CMD_POWER_ON | PORT_CMD_SPIN_UP |
- PORT_CMD_START, port_mmio + PORT_CMD);

-       readl(port_mmio + PORT_CMD); /* flush */
+       rc = ahci_port_spinup(port_mmio, hpriv->cap);
+       if (rc) 

+ ata_port_printk(ap, KERN_WARNING,
+ "Could not spinup port (%d)\n", rc);
+
+ rc = ahci_start_engine(port_mmio);
+ if (rc)
+ ata_port_printk(ap, KERN_WARNING, "Could not start DMA
engine"
+ "of port (%d)\n", rc);

        return 0;
 }
@@ -1411,20 +1411,16 @@ static int ahci_host_init(struct ata_pro
                                (unsigned long) mmio, i);
 
                /* make sure port is not active */
-               tmp = readl(port_mmio + PORT_CMD);
-               VPRINTK("PORT_CMD 0x%x\n", tmp);
-               if (tmp & (PORT_CMD_LIST_ON | PORT_CMD_FIS_ON |

- PORT_CMD_FIS_RX | PORT_CMD_START)) {
- tmp &= ~(PORT_CMD_LIST_ON | PORT_CMD_FIS_ON |
- PORT_CMD_FIS_RX | PORT_CMD_START);
- writel(tmp, port_mmio + PORT_CMD);
- readl(port_mmio + PORT_CMD); /* flush */
-
- /* spec says 500 msecs for each bit, so
- * this is slightly incorrect.
- */
- msleep(500);
- }
+
+ rc = ahci_stop_engine(port_mmio);
+ if (rc)
+ printk(KERN_WARNING "ata%u: DMA engine busy (%d)
\n",
+ i, rc);
+
+ rc = ahci_stop_fis_rx(port_mmio);
+ if (rc)
+ printk(KERN_WARNING "ata%u: FIS RX not stopped
(%d)\n",
+ i, rc);

                writel(PORT_CMD_SPIN_UP, port_mmio + PORT_CMD);

1.2.6