Skip to contentSkip to conversation

sata_promise / libata defaulting to UDMA/33

DISCUSSION Marc 2 participants 3 messages Aug 3, 2006

lore
Share & tools
lore

Marc

author
#0 lore raw

Hi.

I'm having great difficulty solving a problem I've encountered. I have a Promise Fastrak TX4000 card:

0000:00:08.0 RAID bus controller: Promise Technology, Inc. PDC20619 (FastTrak TX4000) (rev 02)
Subsystem: Promise Technology, Inc. PDC20619 (FastTrak TX4000)
Flags: bus master, 66MHz, medium devsel, latency 96, IRQ 137

For some strange reason all drives are set to UDMA/33 mode when the module is loaded and I haven't found a way of changing the UDMA mode (hdparm -X doesn't
work: HDIO_DRIVE_CMD(setxfermode) failed: Input/output error).

Extract from dmesg:

libata version 1.20 loaded.
sata_promise 0000:00:08.0: version 1.04
ata1: PATA max UDMA/133 cmd 0xF8ABC200 ctl 0xF8ABC238 bmdma 0x0 irq 137
ata2: PATA max UDMA/133 cmd 0xF8ABC280 ctl 0xF8ABC2B8 bmdma 0x0 irq 137
ata3: PATA max UDMA/133 cmd 0xF8ABC300 ctl 0xF8ABC338 bmdma 0x0 irq 137
ata4: PATA max UDMA/133 cmd 0xF8ABC380 ctl 0xF8ABC3B8 bmdma 0x0 irq 137
ata1: disabling port
scsi1 : sata_promise
ata2: dev 0 cfg 49:2f00 82:346b 83:7f01 84:4003 85:3469 86:3c01 87:4003 88:203f
ata2: dev 0 ATA-6, max UDMA/100, 312581808 sectors: LBA48
<b>ata2: dev 0 configured for UDMA/33</b>
scsi2 : sata_promise
ata3: dev 0 cfg 49:2f00 82:746b 83:7f01 84:4633 85:7469 86:3c01 87:4623 88:203f
ata3: dev 0 ATA-7, max UDMA/100, 312581808 sectors: LBA48
<b>ata3: dev 0 configured for UDMA/33</b>
scsi3 : sata_promise
ata4: dev 0 cfg 49:2f00 82:346b 83:7f01 84:4003 85:3469 86:3c01 87:4003 88:203f
ata4: dev 0 ATA-6, max UDMA/100, 312581808 sectors: LBA48
<b>ata4: dev 0 configured for UDMA/33</b>
scsi4 : sata_promise

  Vendor: ATA       Model: WDC WD1600JB-00E  Rev: 15.0
  Type:   Direct-Access                      ANSI SCSI revision: 05
  Vendor: ATA       Model: WDC WD1600JB-00R  Rev: 20.0
  Type:   Direct-Access                      ANSI SCSI revision: 05
  Vendor: ATA       Model: WDC WD1600JB-00E  Rev: 15.0
  Type:   Direct-Access                      ANSI SCSI revision: 05

I'm currently running kernel 2.6.17.3. In the controller's BIOS I've created 3 'stripe' arrays with 1 disk per array, the BIOS shows the 3 drives as U5 (UDMA mode 5 - which is UDMA/100 right?).

I've searched high and low but haven't found an answer to this problem. Help appreciated. Please - I'm getting dismal performance.

Regards,

--

#1 lore raw

Ar Gwe, 2006-08-04 am 00:31 +0800, ysgrifennodd Marc:

Quoted 4 lines

Hi.

I'm having great difficulty solving a problem I've encountered. I have a Promise Fastrak TX4000 card:

We knock things down to UDMA33 if they are on an unsuitable cable. The rest of the displayed data looks correct.

Quoted 1 line

ata2: PATA max UDMA/133 cmd 0xF8ABC280 ctl 0xF8ABC2B8 bmdma 0x0 irq 137

Controller does 133

Quoted 2 lines

ata2: dev 0 cfg 49:2f00 82:346b 83:7f01 84:4003 85:3469 86:3c01 87:4003 88:203f
ata2: dev 0 ATA-6, max UDMA/100, 312581808 sectors: LBA48

Devices does UDMA 100

Quoted 1 line

<b>ata2: dev 0 configured for UDMA/33</b>

So this appears to be a cable confusion. One thing that was fixed in recent patches was a bug where if the core code decided something was PATA but the drive setup was in fact SATA it incorrectly clipped to UDMA33.

Quoted 3 lines

I'm currently running kernel 2.6.17.3. In the controller's BIOS I've created 3 'stripe' arrays with 1 disk per array, the BIOS shows the 3 drives as U5 (UDMA mode 5 - which is UDMA/100 right?).

Correct

Quoted 2 lines

I've searched high and low but haven't found an answer to this problem. Help appreciated. Please - I'm getting dismal performance.

I think the needed patch is in 2.6.18-mm, not sure about 2.6.18-rc base. Jeff Garzik would be able to verify what has it merged.

author
#2 lore raw

On Thu, 03 Aug 2006 18:14:49 +0100, Alan Cox wrote

Quoted 6 lines

Ar Gwe, 2006-08-04 am 00:31 +0800, ysgrifennodd Marc:

Quoted 4 lines

Hi.

I'm having great difficulty solving a problem I've encountered. I have a Promise Fastrak TX4000 card:

Quoted 8 lines

We knock things down to UDMA33 if they are on an unsuitable cable. The rest of the displayed data looks correct.

Quoted 1 line

ata2: PATA max UDMA/133 cmd 0xF8ABC280 ctl 0xF8ABC2B8 bmdma 0x0 irq 137

Controller does 133

Quoted 1 line

ata2: dev 0 cfg 49:2f00 82:346b 83:7f01 84:4003 85:3469 86:3c01 87:4003

88:203f

Quoted 16 lines
Quoted 1 line

ata2: dev 0 ATA-6, max UDMA/100, 312581808 sectors: LBA48

Devices does UDMA 100

Quoted 1 line

<b>ata2: dev 0 configured for UDMA/33</b>

So this appears to be a cable confusion. One thing that was fixed in recent patches was a bug where if the core code decided something was PATA but the drive setup was in fact SATA it incorrectly clipped to UDMA33.

Quoted 3 lines

I'm currently running kernel 2.6.17.3. In the controller's BIOS I've created 3 'stripe' arrays with 1 disk per array, the BIOS shows the 3 drives as U5 (UDMA mode 5 - which is UDMA/100 right?).

Correct

Quoted 7 lines
Quoted 2 lines

I've searched high and low but haven't found an answer to this problem. Help appreciated. Please - I'm getting dismal performance.

I think the needed patch is in 2.6.18-mm, not sure about 2.6.18-rc base. Jeff Garzik would be able to verify what has it merged.

-

Thank you. I've compiled and installed 2.6.18-rc3 and it now shows:

ata2: dev 0 configured for UDMA/100

Problem is the system locks up after a few minutes - not sure what's causing that (no flashing keyboard LEDs so it's not a kernel panic). I'll try again tomorrow - its very late here already!

Regards.

--