implement ata_link, take 3
Subsystems (2)
PATCH 1/1 implement ata_link, take 3
Hello, all.
This is the third take of implement ata_link patchset. This patchset contains 18 patches which can be categorized as follows.
#01-03: prep
#04-05: implement ata_link
#06-09: make libata deal with link instead of port #10-12: misc link stuff (link init, reset_tries, ata_link_abort()) #13-19: add ap->pmp_link[] and update libata to deal with multiple
links
ata_link abstracts PHY and sits between ata_port and ata_device. The following attributes are moved to ata_link from ata_port.
- active command state (active_tag, sactive)
- [hw_]sata_spd_limit
- eh_info and eh_context
- device array
With above and a few extra fields, a link can fully host attached devices including qc management and EH/hotplug. This patchset makes libata ready to handle PM links.
Changes from the last take[L] are.
* updated to fit new #upstream
* __dev1 trick removed
This patchset is against
upstream (da54f5fe54c7d75e2db7d17961fb36a8c28a8501)
+ [1] hp-poll patchset, take #5
+ [2] vt8251-ahci patchset, take #2
Thanks.
--
tejun
[L] http://article.gmane.org/gmane.linux.ide/11928
[1] http://article.gmane.org/gmane.linux.ide/13467
[2] http://article.gmane.org/gmane.linux.ide/13471
PATCH 1/18 libata: generate hotplug event on SError read failure
ata_eh_autopsy() used to schedule hardreset for phys which failed to return SError, which isn't enough for some cases. Assume the worst and generate hotplug event instead. Note that scr_read() is guaranteed to succeed for host ports. This change affects only PMP links.
--- drivers/ata/libata-eh.c | 6 ++++-- 1 files changed, 4 insertions(+), 2 deletions(-)
drivers/ata/libata-eh.c +4 -2
@@ -1327,8 +1327,10 @@ static void ata_eh_autopsy(struct ata_poif (rc ==0 ) { ehc->i.serror |= serror;ata_eh_analyze_serror (ap); - }else if (rc != -EOPNOTSUPP ) - ehc->i.action |=ATA_EH_HARDRESET ; + }else if (rc != -EOPNOTSUPP ) { +/* hmmm, assume the worst and generate hotplug event */ +__ata_ehi_hotplugged (&ehc->i); + }/* analyze NCQ failure */ ata_eh_analyze_ncq_error (ap);
Signature · 1 line
1.4.2.3
PATCH 2/18 libata-link: separate out ata_eh_handle_dev_fail()
In reply to Tejun HeoSeparate out ata_eh_handle_dev_fail() from ata_eh_recover(). This is in preparation of ata_link and PMP support.
--- drivers/ata/libata-eh.c | 91 ++++++++++++++++++++++++++--------------------- 1 files changed, 50 insertions(+), 41 deletions(-)
drivers/ata/libata-eh.c +50 -41
@@ -1911,6 +1911,55 @@ static int ata_eh_skip_recovery(struct areturn 1 ; } +static void ata_eh_handle_dev_fail (struct ata_device *dev,int err, +int down_xfermask) +{ +struct ata_port *ap = dev->ap; +struct ata_eh_context *ehc = &ap->eh_context; + +switch (err) { +case -ENODEV : +/* device missing, schedule probing */ + ehc->i.probe_mask |= (1 << dev->devno); +case -EINVAL : + ehc->tries[dev->devno] =0 ; +break ; +case -EIO : +sata_down_spd_limit (ap); +default : + ehc->tries[dev->devno]--; +if (down_xfermask && +ata_down_xfermask_limit (dev, ehc->tries[dev->devno] ==1 )) + ehc->tries[dev->devno] =0 ; + } + +if (ata_dev_enabled (dev) && !ehc->tries[dev->devno]) { +/* disable device if it has used up all its chances */ +ata_dev_disable (dev); + +/* detach if offline */ +if (ata_port_offline (ap)) +ata_eh_detach_dev (dev); + +/* probe if requested */ +if ((ehc->i.probe_mask & (1 << dev->devno)) && + !(ehc->did_probe_mask & (1 << dev->devno))) { +ata_eh_detach_dev (dev); +ata_dev_init (dev); + + ehc->tries[dev->devno] =ATA_EH_DEV_TRIES ; + ehc->did_probe_mask |= (1 << dev->devno); + ehc->i.action |=ATA_EH_SOFTRESET ; + } + }else { +/* soft didn't work? be haaaaard */ +if (ehc->i.flags &ATA_EHI_DID_RESET ) + ehc->i.action |=ATA_EH_HARDRESET ; +else + ehc->i.action |=ATA_EH_SOFTRESET ; + } +} +/** * ata_eh_recover - recover host port after error * @ap: host port to recover
@@ -2022,47 +2071,7 @@ static int ata_eh_recover(struct ata_por goto out; dev_fail: -switch (rc) { -case -ENODEV : -/* device missing, schedule probing */ - ehc->i.probe_mask |= (1 << dev->devno); -case -EINVAL : - ehc->tries[dev->devno] =0 ; -break ; -case -EIO : -sata_down_spd_limit (ap); -default : - ehc->tries[dev->devno]--; -if (down_xfermask && -ata_down_xfermask_limit (dev, ehc->tries[dev->devno] ==1 )) - ehc->tries[dev->devno] =0 ; - } - -if (ata_dev_enabled (dev) && !ehc->tries[dev->devno]) { -/* disable device if it has used up all its chances */ -ata_dev_disable (dev); - -/* detach if offline */ -if (ata_port_offline (ap)) -ata_eh_detach_dev (dev); - -/* probe if requested */ -if ((ehc->i.probe_mask & (1 << dev->devno)) && - !(ehc->did_probe_mask & (1 << dev->devno))) { -ata_eh_detach_dev (dev); -ata_dev_init (dev); - - ehc->tries[dev->devno] =ATA_EH_DEV_TRIES ; - ehc->did_probe_mask |= (1 << dev->devno); - ehc->i.action |=ATA_EH_SOFTRESET ; - } - }else { -/* soft didn't work? be haaaaard */ -if (ehc->i.flags &ATA_EHI_DID_RESET ) - ehc->i.action |=ATA_EH_HARDRESET ; -else - ehc->i.action |=ATA_EH_SOFTRESET ; - } +ata_eh_handle_dev_fail (dev, rc, down_xfermask);if (ata_port_nr_enabled (ap)) { ata_port_printk(ap, KERN_WARNING, "failed to recover some "
Signature · 1 line
1.4.2.3
PATCH 3/18 libata-link: add PMP related ATA constants
In reply to Tejun HeoAdd Port Multiplier related ATA constants and macros. Some of these will be used by ata_link implementation.
--- include/linux/ata.h | 29 +++++++++++++++++++++++++++++ 1 files changed, 29 insertions(+), 0 deletions(-)
include/linux/ata.h +29 -0
@@ -156,6 +156,8 @@ enum {ATA_CMD_READ_NATIVE_MAX =0xF8 ,ATA_CMD_READ_NATIVE_MAX_EXT =0x27 ,ATA_CMD_READ_LOG_EXT =0x2f , +ATA_CMD_PMP_READ =0xE4 , +ATA_CMD_PMP_WRITE =0xE8 ,/* READ_LOG_EXT pages */ ATA_LOG_SATA_NCQ = 0x10,
@@ -196,6 +198,28 @@ enum {0=to device, 1=to host */ ATAPI_CDB_LEN =16 , +/* PMP stuff */ +SATA_PMP_MAX_PORTS =15 , +SATA_PMP_CTRL_PORT =15 , + +SATA_PMP_GSCR_DWORDS =128 , +SATA_PMP_GSCR_PROD_ID =0 , +SATA_PMP_GSCR_REV =1 , +SATA_PMP_GSCR_PORT_INFO =2 , +SATA_PMP_GSCR_ERROR =32 , +SATA_PMP_GSCR_ERROR_EN =33 , +SATA_PMP_GSCR_FEAT =64 , +SATA_PMP_GSCR_FEAT_EN =96 , + +SATA_PMP_PSCR_STATUS =0 , +SATA_PMP_PSCR_ERROR =1 , +SATA_PMP_PSCR_CONTROL =2 , + +SATA_PMP_FEAT_BIST = (1 <<0 ), +SATA_PMP_FEAT_PMREQ = (1 <<1 ), +SATA_PMP_FEAT_DYNSSC = (1 <<2 ), +SATA_PMP_FEAT_NOTIFY = (1 <<3 ), +/* cable types */ ATA_CBL_NONE =0 , ATA_CBL_PATA40 = 1,
@@ -396,4 +420,9 @@ static inline int lba_48_ok(u64 block, u return ((block + n_block - 1) < ((u64)1 << 48)) && (n_block <= 65536); } +#define sata_pmp_gscr_vendor (gscr) ((gscr)[SATA_PMP_GSCR_PROD_ID] & 0xffff) +#define sata_pmp_gscr_devid (gscr) ((gscr)[SATA_PMP_GSCR_PROD_ID] >> 16) +#define sata_pmp_gscr_rev (gscr) (((gscr)[SATA_PMP_GSCR_REV] >> 8) & 0xff) +#define sata_pmp_gscr_ports (gscr) ((gscr)[SATA_PMP_GSCR_PORT_INFO] & 0xf) +#endif /* __LINUX_ATA_H__ */
Signature · 1 line
1.4.2.3
PATCH 4/18 libata-link: introduce ata_link
In reply to Tejun HeoIntroduce ata_link. It abstracts PHY and sits between ata_port and ata_device. This new level of abstraction is necessary to support SATA Port Multiplier, which basically adds a bunch of links (PHYs) to a ATA host port. Fields related to command execution, spd_limit and EH are per-link and thus moved to ata_link.
This patch only defines the host link. Multiple link handling will be added later. Also, a lot of ap->link derefences are added but many of them will be removed as each part is converted to deal directly with ata_link instead of ata_port.
This patch introduces no behavior change.
--- drivers/ata/ahci.c | 20 +++--- drivers/ata/ata_generic.c | 2 - drivers/ata/ata_piix.c | 2 - drivers/ata/libata-core.c | 147 +++++++++++++++++++++++-------------------- drivers/ata/libata-eh.c | 106 ++++++++++++++++--------------- drivers/ata/libata-scsi.c | 46 +++++++------ drivers/ata/libata-sff.c | 4 + drivers/ata/pata_it821x.c | 4 + drivers/ata/pata_optidma.c | 4 + drivers/ata/pata_pdc2027x.c | 2 - drivers/ata/pata_rz1000.c | 2 - drivers/ata/pata_sis.c | 2 - drivers/ata/pdc_adma.c | 4 + drivers/ata/sata_mv.c | 6 +- drivers/ata/sata_nv.c | 4 + drivers/ata/sata_promise.c | 4 + drivers/ata/sata_qstor.c | 4 + drivers/ata/sata_sil.c | 8 +- drivers/ata/sata_sil24.c | 10 +-- drivers/ata/sata_sx4.c | 4 + drivers/ata/sata_via.c | 2 - drivers/ata/sata_vsc.c | 2 - include/linux/libata.h | 38 +++++++---- 23 files changed, 225 insertions(+), 202 deletions(-)
drivers/ata/ahci.c +10 -10
@@ -776,7 +776,7 @@ static int ahci_softreset(struct ata_por/* restart engine */ ahci_start_engine (port_mmio); -ata_tf_init (ap->device, &tf); +ata_tf_init (ap->link.device, &tf); fis = pp->cmd_tbl;/* issue the first D2H Register FIS */
@@ -853,7 +853,7 @@ static int ahci_hardreset(struct ata_porahci_stop_engine (port_mmio);/* clear D2H reception area to properly wait for D2H FIS */ -ata_tf_init (ap->device, &tf); +ata_tf_init (ap->link.device, &tf); tf.command =0xff ;ata_tf_to_fis (&tf, d2h_fis,0 );
@@ -880,7 +880,7 @@ static int ahci_vt8251_hardreset(structahci_stop_engine (port_mmio); - rc =sata_port_hardreset (ap,sata_ehc_deb_timing (&ap->eh_context)); + rc =sata_port_hardreset (ap,sata_ehc_deb_timing (&ap->link.eh_context));/* vt8251 needs SError cleared for the port to operate */ ahci_scr_write (ap,SCR_ERROR ,ahci_scr_read (ap,SCR_ERROR ));
@@ -997,7 +997,7 @@ static void ahci_qc_prep(struct ata_queustatic void ahci_error_intr (struct ata_port *ap,u32 irq_stat) {struct ahci_port_priv *pp = ap->private_data; -struct ata_eh_info *ehi = &ap->eh_info; +struct ata_eh_info *ehi = &ap->link.eh_info;unsigned int err_mask =0 , action =0 ;struct ata_queued_cmd *qc;u32 serror;
@@ -1044,7 +1044,7 @@ static void ahci_error_intr(struct ata_p ehi->serror |= serror; ehi->action |= action; - qc =ata_qc_from_tag (ap, ap->active_tag); + qc =ata_qc_from_tag (ap, ap->link.active_tag);if (qc) qc->err_mask |= err_mask;else
@@ -1060,7 +1060,7 @@ static void ahci_host_intr(struct ata_po {void __iomem *mmio = ap->host->mmio_base;void __iomem *port_mmio =ahci_port_base (mmio, ap->port_no); -struct ata_eh_info *ehi = &ap->eh_info; +struct ata_eh_info *ehi = &ap->link.eh_info;u32 status, qc_active;int rc;
@@ -1072,7 +1072,7 @@ static void ahci_host_intr(struct ata_poreturn ; } -if (ap->sactive) +if (ap->link.sactive) qc_active =readl (port_mmio +PORT_SCR_ACT );else qc_active =readl (port_mmio +PORT_CMD_ISSUE );
@@ -1090,17 +1090,17 @@ static void ahci_host_intr(struct ata_po/* hmmm... a spurious interupt */ /* some devices send D2H reg with I bit set during NCQ command phase */ -if (ap->sactive && status &PORT_IRQ_D2H_REG_FIS ) +if (ap->link.sactive && status &PORT_IRQ_D2H_REG_FIS )return ;/* ignore interim PIO setup fis interrupts */ -if (ata_tag_valid (ap->active_tag) && (status &PORT_IRQ_PIOS_FIS )) +if (ata_tag_valid (ap->link.active_tag) && (status &PORT_IRQ_PIOS_FIS ))return ;if (ata_ratelimit ())ata_port_printk (ap,KERN_INFO ,"spurious interrupt " "(irq_stat 0x%x active_tag %d sactive 0x%x)\n" , - status, ap->active_tag, ap->sactive); + status, ap->link.active_tag, ap->link.sactive); }static void ahci_irq_clear (struct ata_port *ap)
drivers/ata/ata_generic.c +1 -1
@@ -81,7 +81,7 @@ static void generic_set_mode(struct ata_ dma_enabled =inb (ap->ioaddr.bmdma_addr +ATA_DMA_CMD );for (i =0 ; i <ATA_MAX_DEVICES ; i++) { -struct ata_device *dev = &ap->device[i]; +struct ata_device *dev = &ap->link.device[i];if (ata_dev_enabled (dev)) {/* We don't really care */ dev->pio_mode =XFER_PIO_0 ;
drivers/ata/ata_piix.c +1 -1
@@ -700,7 +700,7 @@ static int ich_pata_prereset(struct ata_if (!pci_test_config_bits (pdev, &piix_enable_bits[ap->port_no])) {ata_port_printk (ap,KERN_INFO ,"port disabled. ignoring.\n" ); - ap->eh_context.i.action &= ~ATA_EH_RESET_MASK ; + ap->link.eh_context.i.action &= ~ATA_EH_RESET_MASK ;return 0 ; }
drivers/ata/libata-core.c +78 -69
465 lines not on this page · raw message
drivers/ata/libata-eh.c +54 -52
360 lines not on this page · raw message
drivers/ata/libata-scsi.c +24 -22
153 lines not on this page · raw message
drivers/ata/libata-sff.c +2 -2
@@ -714,12 +714,12 @@ void ata_bmdma_drive_eh(struct ata_port ata_reset_fn_t softreset, ata_reset_fn_t hardreset, ata_postreset_fn_t postreset) { - struct ata_eh_context *ehc = &ap->eh_context; + struct ata_eh_context *ehc = &ap->link.eh_context;struct ata_queued_cmd *qc;unsigned long flags;int thaw =0 ; - qc =__ata_qc_from_tag (ap, ap->active_tag); + qc =__ata_qc_from_tag (ap, ap->link.active_tag);if (qc && !(qc->flags &ATA_QCFLAG_FAILED )) qc =NULL ;
drivers/ata/pata_it821x.c +2 -2
@@ -416,7 +416,7 @@ static void it821x_passthru_dev_select(s {struct it821x_dev *itdev = ap->private_data;if (itdev && device != itdev->last_device) { -struct ata_device *adev = &ap->device[device]; +struct ata_device *adev = &ap->link.device[device];it821x_program (ap, adev, itdev->pio[adev->devno]); itdev->last_device = device; }
@@ -494,7 +494,7 @@ static void it821x_smart_set_mode(struct dma_enabled =inb (ap->ioaddr.bmdma_addr +ATA_DMA_CMD );for (i =0 ; i <ATA_MAX_DEVICES ; i++) { -struct ata_device *dev = &ap->device[i]; +struct ata_device *dev = &ap->link.device[i];if (ata_dev_enabled (dev)) {/* We don't really care */ dev->pio_mode =XFER_PIO_0 ;
drivers/ata/pata_optidma.c +2 -2
@@ -338,8 +338,8 @@ static void optidma_post_set_mode(structpci_read_config_byte (pdev,0x43 , &r); r &= (0x0F << nybble); - r |= (optidma_make_bits43 (&ap->device[0 ]) + - (optidma_make_bits43 (&ap->device[0 ]) <<2 )) << nybble; + r |= (optidma_make_bits43 (&ap->link.device[0 ]) + + (optidma_make_bits43 (&ap->link.device[0 ]) <<2 )) << nybble;pci_write_config_byte (pdev,0x43 , r); }
drivers/ata/pata_pdc2027x.c +1 -1
@@ -456,7 +456,7 @@ static void pdc2027x_post_set_mode(strucint i;for (i =0 ; i <ATA_MAX_DEVICES ; i++) { -struct ata_device *dev = &ap->device[i]; +struct ata_device *dev = &ap->link.device[i];if (ata_dev_enabled (dev)) {
drivers/ata/pata_rz1000.c +1 -1
@@ -63,7 +63,7 @@ static void rz1000_set_mode(struct ata_pint i;for (i =0 ; i <ATA_MAX_DEVICES ; i++) { -struct ata_device *dev = &ap->device[i]; +struct ata_device *dev = &ap->link.device[i];if (ata_dev_enabled (dev)) {/* We don't really care */ dev->pio_mode =XFER_PIO_0 ;
drivers/ata/pata_sis.c +1 -1
@@ -53,7 +53,7 @@ struct sis_chipset {static int sis_port_base (struct ata_device *adev) { -return 0x40 + (4 * adev->ap->port_no) + (2 * adev->devno); +return 0x40 + (4 * adev->link->ap->port_no) + (2 * adev->devno); }/**
drivers/ata/pdc_adma.c +2 -2
@@ -461,7 +461,7 @@ static inline unsigned int adma_intr_pkt pp = ap->private_data;if (!pp || pp->state != adma_state_pkt)continue ; - qc =ata_qc_from_tag (ap, ap->active_tag); + qc =ata_qc_from_tag (ap, ap->link.active_tag);if (qc && (!(qc->tf.flags &ATA_TFLAG_POLLING ))) {if ((status & (aPERR | aPSD | aUIRQ))) qc->err_mask |=AC_ERR_OTHER ;
@@ -486,7 +486,7 @@ static inline unsigned int adma_intr_mmistruct adma_port_priv *pp = ap->private_data;if (!pp || pp->state != adma_state_mmio)continue ; - qc =ata_qc_from_tag (ap, ap->active_tag); + qc =ata_qc_from_tag (ap, ap->link.active_tag);if (qc && (!(qc->tf.flags &ATA_TFLAG_POLLING ))) {/* check main status, clearing INTRQ */
drivers/ata/sata_mv.c +3 -3
@@ -1417,7 +1417,7 @@ static void mv_host_intr(struct ata_host }if (handled) { - qc =ata_qc_from_tag (ap, ap->active_tag); + qc =ata_qc_from_tag (ap, ap->link.active_tag);if (qc && (qc->flags &ATA_QCFLAG_ACTIVE )) {VPRINTK ("port %u IRQ found for qc, " "ata_status 0x%x\n" , port,ata_status);
@@ -1938,7 +1938,7 @@ static void __mv_phy_reset(struct ata_postruct mv_host_priv *hpriv = ap->host->private_data;void __iomem *port_mmio =mv_ap_base (ap);struct ata_taskfile tf; -struct ata_device *dev = &ap->device[0 ]; +struct ata_device *dev = &ap->link.device[0 ];unsigned long timeout;int retry =5 ;u32 sstatus;
@@ -2045,7 +2045,7 @@ static void mv_eng_timeout(struct ata_pomv_dump_all_regs (ap->host->mmio_base, ap->port_no,to_pci_dev (ap->host->dev)); - qc =ata_qc_from_tag (ap, ap->active_tag); + qc =ata_qc_from_tag (ap, ap->link.active_tag);printk (KERN_ERR "mmio_base %p ap %p qc %p scsi_cmnd %p &cmnd %p\n" , ap->host->mmio_base, ap, qc, qc->scsicmd, &qc->scsicmd->cmnd);
drivers/ata/sata_nv.c +2 -2
@@ -297,7 +297,7 @@ static irqreturn_t nv_generic_interrupt( !(ap->flags & ATA_FLAG_DISABLED)) {struct ata_queued_cmd *qc; - qc =ata_qc_from_tag (ap, ap->active_tag); + qc =ata_qc_from_tag (ap, ap->link.active_tag);if (qc && (!(qc->tf.flags &ATA_TFLAG_POLLING ))) handled +=ata_host_intr (ap, qc);else
@@ -315,7 +315,7 @@ static irqreturn_t nv_generic_interrupt(static int nv_host_intr (struct ata_port *ap,u8 irq_stat) { -struct ata_queued_cmd *qc =ata_qc_from_tag (ap, ap->active_tag); +struct ata_queued_cmd *qc =ata_qc_from_tag (ap, ap->link.active_tag);int handled;/* freeze if hotplugged */
drivers/ata/sata_promise.c +2 -2
@@ -436,7 +436,7 @@ static void pdc_eng_timeout(struct ata_pspin_lock_irqsave (&host->lock, flags); - qc =ata_qc_from_tag (ap, ap->active_tag); + qc =ata_qc_from_tag (ap, ap->link.active_tag);switch (qc->tf.protocol) {case ATA_PROT_DMA :
@@ -543,7 +543,7 @@ static irqreturn_t pdc_interrupt (int ir !(ap->flags & ATA_FLAG_DISABLED)) {struct ata_queued_cmd *qc; - qc =ata_qc_from_tag (ap, ap->active_tag); + qc =ata_qc_from_tag (ap, ap->link.active_tag);if (qc && (!(qc->tf.flags &ATA_TFLAG_POLLING ))) handled +=pdc_host_intr (ap, qc); }
drivers/ata/sata_qstor.c +2 -2
@@ -400,7 +400,7 @@ static inline unsigned int qs_intr_pkt(sstruct qs_port_priv *pp = ap->private_data;if (!pp || pp->state != qs_state_pkt)continue ; - qc =ata_qc_from_tag (ap, ap->active_tag); + qc =ata_qc_from_tag (ap, ap->link.active_tag);if (qc && (!(qc->tf.flags &ATA_TFLAG_POLLING ))) {switch (sHST) {case 0 :/* successful CPB */
@@ -433,7 +433,7 @@ static inline unsigned int qs_intr_mmio(struct qs_port_priv *pp = ap->private_data;if (!pp || pp->state != qs_state_mmio)continue ; - qc =ata_qc_from_tag (ap, ap->active_tag); + qc =ata_qc_from_tag (ap, ap->link.active_tag);if (qc && (!(qc->tf.flags &ATA_TFLAG_POLLING ))) {/* check main status, clearing INTRQ */
drivers/ata/sata_sil.c +4 -4
@@ -303,7 +303,7 @@ static void sil_post_set_mode (struct atunsigned int i;for (i =0 ; i <2 ; i++) { - dev = &ap->device[i]; + dev = &ap->link.device[i];if (!ata_dev_enabled (dev)) dev_mode[i] =0 ;/* PIO0/1/2 */ else if (dev->flags &ATA_DFLAG_PIO )
@@ -357,7 +357,7 @@ static void sil_scr_write (struct ata_postatic void sil_host_intr (struct ata_port *ap,u32 bmdma2) { -struct ata_queued_cmd *qc =ata_qc_from_tag (ap, ap->active_tag); +struct ata_queued_cmd *qc =ata_qc_from_tag (ap, ap->link.active_tag);u8 status;if (unlikely (bmdma2 &SIL_DMA_SATA_IRQ )) {
@@ -376,8 +376,8 @@ static void sil_host_intr(struct ata_por* repeat probing needlessly. */ if (!(ap->pflags &ATA_PFLAG_FROZEN )) { -ata_ehi_hotplugged (&ap->eh_info); - ap->eh_info.serror |= serror; +ata_ehi_hotplugged (&ap->link.eh_info); + ap->link.eh_info.serror |= serror; } goto freeze;
drivers/ata/sata_sil24.c +5 -5
@@ -764,7 +764,7 @@ static void sil24_thaw(struct ata_port *static void sil24_error_intr (struct ata_port *ap) {void __iomem *port = (void __iomem *)ap->ioaddr.cmd_addr; -struct ata_eh_info *ehi = &ap->eh_info; +struct ata_eh_info *ehi = &ap->link.eh_info;int freeze =0 ;u32 irq_stat;
@@ -816,7 +816,7 @@ static void sil24_error_intr(struct ata_ }/* record error info */ - qc =ata_qc_from_tag (ap, ap->active_tag); + qc =ata_qc_from_tag (ap, ap->link.active_tag);if (qc) {sil24_update_tf (ap); qc->err_mask |= err_mask;
@@ -860,7 +860,7 @@ static inline void sil24_host_intr(strucif (rc >0 )return ;if (rc <0 ) { -struct ata_eh_info *ehi = &ap->eh_info; +struct ata_eh_info *ehi = &ap->link.eh_info; ehi->err_mask |=AC_ERR_HSM ; ehi->action |=ATA_EH_SOFTRESET ;ata_port_freeze (ap);
@@ -870,7 +870,7 @@ static inline void sil24_host_intr(strucif (ata_ratelimit ())ata_port_printk (ap,KERN_INFO ,"spurious interrupt " "(slot_stat 0x%x active_tag %d sactive 0x%x)\n" , - slot_stat, ap->active_tag, ap->sactive); + slot_stat, ap->link.active_tag, ap->link.sactive); }static irqreturn_t sil24_interrupt (int irq,void *dev_instance)
@@ -912,7 +912,7 @@ static irqreturn_t sil24_interrupt(int istatic void sil24_error_handler (struct ata_port *ap) { -struct ata_eh_context *ehc = &ap->eh_context; +struct ata_eh_context *ehc = &ap->link.eh_context;if (sil24_init_port (ap)) {ata_eh_freeze_port (ap);
drivers/ata/sata_sx4.c +2 -2
@@ -837,7 +837,7 @@ static irqreturn_t pdc20621_interrupt (i !(ap->flags & ATA_FLAG_DISABLED)) {struct ata_queued_cmd *qc; - qc =ata_qc_from_tag (ap, ap->active_tag); + qc =ata_qc_from_tag (ap, ap->link.active_tag);if (qc && (!(qc->tf.flags &ATA_TFLAG_POLLING ))) handled +=pdc20621_host_intr (ap, qc, (i >4 ), mmio_base);
@@ -864,7 +864,7 @@ static void pdc_eng_timeout(struct ata_pspin_lock_irqsave (&host->lock, flags); - qc =ata_qc_from_tag (ap, ap->active_tag); + qc =ata_qc_from_tag (ap, ap->link.active_tag);switch (qc->tf.protocol) {case ATA_PROT_DMA :
drivers/ata/sata_via.c +1 -1
@@ -224,7 +224,7 @@ static void svia_scr_write (struct ata_p*/ static int vt6420_prereset (struct ata_port *ap) { -struct ata_eh_context *ehc = &ap->eh_context; +struct ata_eh_context *ehc = &ap->link.eh_context;unsigned long timeout = jiffies + (HZ *5 );u32 sstatus, scontrol;int online;
drivers/ata/sata_vsc.c +1 -1
@@ -231,7 +231,7 @@ static irqreturn_t vsc_sata_interrupt (iif (ap && !(ap->flags &ATA_FLAG_DISABLED )) {struct ata_queued_cmd *qc; - qc =ata_qc_from_tag (ap, ap->active_tag); + qc =ata_qc_from_tag (ap, ap->link.active_tag);if (qc && (!(qc->tf.flags &ATA_TFLAG_POLLING ))) handled +=ata_host_intr (ap, qc);else if (is_vsc_sata_int_err (i, int_status)) {
include/linux/libata.h +24 -14
@@ -467,7 +467,7 @@ struct ata_ering { };struct ata_device { -struct ata_port *ap; +struct ata_link *link;unsigned int devno;/* 0 or 1 */ unsigned long flags;/* ATA_DFLAG_xxx */ struct scsi_device *sdev;/* attached SCSI device */
@@ -527,6 +527,23 @@ struct ata_eh_context {unsigned int did_probe_mask; }; +struct ata_link { +struct ata_port *ap; + +unsigned int active_tag;/* active tag on this link */ +u32 sactive;/* active NCQ commands */ + +unsigned int hw_sata_spd_limit; +unsigned int sata_spd_limit; + +/* record runtime error info, protected by host_set lock */ +struct ata_eh_info eh_info; +/* EH context */ +struct ata_eh_context eh_context; + +struct ata_device device[ATA_MAX_DEVICES ]; +}; +struct ata_port {struct Scsi_Host *scsi_host;/* our co-allocated scsi host */ const struct ata_port_operations *ops;
@@ -550,22 +567,12 @@ struct ata_port {unsigned int mwdma_mask;unsigned int udma_mask;unsigned int cbl;/* cable type; ATA_CBL_xxx */ -unsigned int hw_sata_spd_limit; -unsigned int sata_spd_limit;/* SATA PHY speed limit */ - -/* record runtime error info, protected by host lock */ -struct ata_eh_info eh_info; -/* EH context owned by EH */ -struct ata_eh_context eh_context; - -struct ata_device device[ATA_MAX_DEVICES ];struct ata_queued_cmd qcmd[ATA_MAX_QUEUE ];unsigned long qc_allocated;unsigned int qc_active; -unsigned int active_tag; -u32 sactive; +struct ata_link link;/* host default link */ struct ata_port_stats stats;struct ata_host *host;
@@ -898,8 +905,11 @@ extern void ata_do_eh(struct ata_port *a #define ata_port_printk(ap, lv, fmt, args...) \ printk(lv"ata%u: "fmt, (ap)->id , ##args) +#define ata_link_printk(link, lv, fmt, args...) \ + printk(lv"ata%u: "fmt, (link)->ap->id , ##args) + #define ata_dev_printk(dev, lv, fmt, args...) \ - printk(lv"ata%u.%02u: "fmt, (dev)->ap->id, (dev)->devno , ##args) + printk(lv"ata%u.%02u: "fmt, (dev)->link->ap->id, (dev)->devno , ##args)/* * ata_eh_info helpers
@@ -1137,7 +1147,7 @@ static inline void ata_tf_init(struct at {memset (tf,0 ,sizeof (*tf)); - tf->ctl = dev->ap->ctl; + tf->ctl = dev->link->ap->ctl;if (dev->devno ==0 ) tf->device =ATA_DEVICE_OBS ;else
Signature · 1 line
1.4.2.3
PATCH 5/18 libata-link: implement and use link/device iterators
In reply to Tejun HeoMultiple links and different number of devices per link should be considered to iterate over links and devices. This patch implements and uses link and device iterators - ata_port_for_each_link() and ata_link_for_each_dev() - and ata_link_max_devices().
This change makes a lot of functions iterate over only possible devices instead of from dev 0 to dev ATA_MAX_DEVICES. All such changes have been examined and nothing should be broken.
While at it, add a separating comment before device helpers to distinguish them better from link helpers and others.
--- drivers/ata/ata_generic.c | 7 +- drivers/ata/ata_piix.c | 9 ++- drivers/ata/libata-core.c | 74 ++++++++++------------ drivers/ata/libata-eh.c | 142 ++++++++++++++++++++----------------------- drivers/ata/libata-scsi.c | 26 +++----- drivers/ata/pata_it821x.c | 7 +- drivers/ata/pata_legacy.c | 5 +- drivers/ata/pata_pdc2027x.c | 6 +- drivers/ata/pata_rz1000.c | 5 +- include/linux/libata.h | 14 +++- 10 files changed, 137 insertions(+), 158 deletions(-)
drivers/ata/ata_generic.c +3 -4
@@ -74,21 +74,20 @@ static void generic_error_handler(structstatic void generic_set_mode (struct ata_port *ap) {int dma_enabled =0 ; -int i; +struct ata_device *dev;/* Bits 5 and 6 indicate if DMA is active on master/slave */ if (ap->ioaddr.bmdma_addr) dma_enabled =inb (ap->ioaddr.bmdma_addr +ATA_DMA_CMD ); -for (i =0 ; i <ATA_MAX_DEVICES ; i++) { -struct ata_device *dev = &ap->link.device[i]; +ata_link_for_each_dev (dev, &ap->link) {if (ata_dev_enabled (dev)) {/* We don't really care */ dev->pio_mode =XFER_PIO_0 ; dev->dma_mode =XFER_MW_DMA_0 ;/* We do need the right mode information for DMA or PIO and this comes from the current configuration flags */ -if (dma_enabled & (1 << (5 + i))) { +if (dma_enabled & (1 << (5 + dev->devno))) { dev->xfer_mode =XFER_MW_DMA_0 ; dev->xfer_shift =ATA_SHIFT_MWDMA ; dev->flags &= ~ATA_DFLAG_PIO ;
drivers/ata/ata_piix.c +5 -4
@@ -774,7 +774,8 @@ static unsigned int piix_sata_present_mastatic int piix_sata_softreset (struct ata_port *ap,unsigned int *classes) {unsigned int present_mask; -int i, rc; +struct ata_device *dev; +int rc; present_mask =piix_sata_present_mask (ap);
@@ -782,9 +783,9 @@ static int piix_sata_softreset(struct atif (rc)return rc; -for (i =0 ; i <ATA_MAX_DEVICES ; i++) { -if (!(present_mask & (1 << i))) - classes[i] =ATA_DEV_NONE ; +ata_link_for_each_dev (dev, &ap->link) { +if (!(present_mask & (1 << dev->devno))) + classes[dev->devno] =ATA_DEV_NONE ; }return 0 ;
drivers/ata/libata-core.c +32 -42
190 lines not on this page · raw message
drivers/ata/libata-eh.c +67 -75
327 lines not on this page · raw message
drivers/ata/libata-scsi.c +10 -16
@@ -543,7 +543,7 @@ int ata_scsi_device_resume(struct scsi_d/* We don't want autopsy and verbose EH messages. Disable * those if we're the only device on this link. */ -if (ata_port_max_devices (ap) ==1 ) +if (ata_link_max_devices (dev->link) ==1 ) ehi->flags |=ATA_EHI_NO_AUTOPSY |ATA_EHI_QUIET ;ata_port_schedule_eh (ap);
@@ -2521,7 +2521,7 @@ static unsigned int atapi_xlat(struct atstatic struct ata_device *ata_find_dev (struct ata_port *ap,int id) { -if (likely (id <ATA_MAX_DEVICES )) +if (likely (id <ata_link_max_devices (&ap->link)))return &ap->link.device[id];return NULL ; }
@@ -2975,19 +2975,18 @@ void ata_scsi_simulate(struct ata_devicevoid ata_scsi_scan_host (struct ata_port *ap) { -unsigned int i; +struct ata_device *dev;if (ap->flags &ATA_FLAG_DISABLED )return ; -for (i =0 ; i <ATA_MAX_DEVICES ; i++) { -struct ata_device *dev = &ap->link.device[i]; +ata_link_for_each_dev (dev, &ap->link) {struct scsi_device *sdev;if (!ata_dev_enabled (dev) || dev->sdev)continue ; - sdev =__scsi_add_device (ap->scsi_host,0 , i,0 ,NULL ); + sdev =__scsi_add_device (ap->scsi_host,0 , dev->devno,0 ,NULL );if (!IS_ERR (sdev)) { dev->sdev = sdev;scsi_device_put (sdev);
@@ -3093,7 +3092,7 @@ static void ata_scsi_remove_dev(struct avoid ata_scsi_hotplug (void *data) {struct ata_port *ap = data; -int i; +struct ata_device *dev;if (ap->pflags &ATA_PFLAG_UNLOADING ) {DPRINTK ("ENTER/EXIT - unloading\n" );
@@ -3103,8 +3102,7 @@ void ata_scsi_hotplug(void *data)DPRINTK ("ENTER\n" );/* unplug detached devices */ -for (i =0 ; i <ATA_MAX_DEVICES ; i++) { -struct ata_device *dev = &ap->link.device[i]; +ata_link_for_each_dev (dev, &ap->link) {unsigned long flags;if (!(dev->flags &ATA_DFLAG_DETACHED ))
@@ -3124,8 +3122,7 @@ void ata_scsi_hotplug(void *data)* failed silently. Requeue if there are enabled but * unattached devices. */ -for (i =0 ; i <ATA_MAX_DEVICES ; i++) { -struct ata_device *dev = &ap->link.device[i]; +ata_link_for_each_dev (dev, &ap->link) {if (ata_dev_enabled (dev) && !dev->sdev) {queue_delayed_work (ata_aux_wq, &ap->hotplug_task,HZ );break ;
@@ -3169,7 +3166,7 @@ static int ata_scsi_user_scan(struct Scsspin_lock_irqsave (ap->lock, flags);if (id ==SCAN_WILD_CARD ) { - ehi->probe_mask |= (1 <<ATA_MAX_DEVICES ) -1 ; + ehi->probe_mask |= (1 <<ata_link_max_devices (&ap->link)) -1 ; ehi->action |=ATA_EH_SOFTRESET ; }else {struct ata_device *dev =ata_find_dev (ap, id);
@@ -3206,11 +3203,8 @@ void ata_scsi_dev_rescan(void *data) {struct ata_port *ap = data;struct ata_device *dev; -unsigned int i; - -for (i =0 ; i <ATA_MAX_DEVICES ; i++) { - dev = &ap->link.device[i]; +ata_link_for_each_dev (dev, &ap->link) {if (ata_dev_enabled (dev) && dev->sdev)scsi_rescan_device (&(dev->sdev->sdev_gendev)); }
drivers/ata/pata_it821x.c +3 -4
@@ -486,22 +486,21 @@ static unsigned int it821x_passthru_qc_istatic void it821x_smart_set_mode (struct ata_port *ap) {int dma_enabled =0 ; -int i; +struct ata_device *dev;/* Bits 5 and 6 indicate if DMA is active on master/slave */ /* It is possible that BMDMA isn't allocated */ if (ap->ioaddr.bmdma_addr) dma_enabled =inb (ap->ioaddr.bmdma_addr +ATA_DMA_CMD ); -for (i =0 ; i <ATA_MAX_DEVICES ; i++) { -struct ata_device *dev = &ap->link.device[i]; +ata_link_for_each_dev (dev, &ap->link) {if (ata_dev_enabled (dev)) {/* We don't really care */ dev->pio_mode =XFER_PIO_0 ; dev->dma_mode =XFER_MW_DMA_0 ;/* We do need the right mode information for DMA or PIO and this comes from the current configuration flags */ -if (dma_enabled & (1 << (5 + i))) { +if (dma_enabled & (1 << (5 + dev->devno))) { dev->xfer_mode =XFER_MW_DMA_0 ; dev->xfer_shift =ATA_SHIFT_MWDMA ; dev->flags &= ~ATA_DFLAG_PIO ;
drivers/ata/pata_legacy.c +2 -3
@@ -107,10 +107,9 @@ static int pio_mask = 0x1F; /* PIO rangstatic void legacy_set_mode (struct ata_port *ap) { -int i; +struct ata_device *dev; -for (i =0 ; i <ATA_MAX_DEVICES ; i++) { -struct ata_device *dev = &ap->device[i]; +ata_link_for_each_dev (dev, &ap->link) {if (ata_dev_enabled (dev)) { dev->pio_mode =XFER_PIO_0 ; dev->xfer_mode =XFER_PIO_0 ;
drivers/ata/pata_pdc2027x.c +2 -4
@@ -453,11 +453,9 @@ static void pdc2027x_set_dmamode(struct*/ static void pdc2027x_post_set_mode (struct ata_port *ap) { -int i; - -for (i =0 ; i <ATA_MAX_DEVICES ; i++) { -struct ata_device *dev = &ap->link.device[i]; +struct ata_device *dev; +ata_link_for_each_dev (dev, &ap->link) {if (ata_dev_enabled (dev)) {pdc2027x_set_piomode (ap, dev);
drivers/ata/pata_rz1000.c +2 -3
@@ -60,10 +60,9 @@ static void rz1000_error_handler(structstatic void rz1000_set_mode (struct ata_port *ap) { -int i; +struct ata_device *dev; -for (i =0 ; i <ATA_MAX_DEVICES ; i++) { -struct ata_device *dev = &ap->link.device[i]; +ata_link_for_each_dev (dev, &ap->link) {if (ata_dev_enabled (dev)) {/* We don't really care */ dev->pio_mode =XFER_PIO_0 ;
include/linux/libata.h +11 -3
@@ -1032,15 +1032,23 @@ static inline unsigned int ata_dev_ready }/* -* port helpers +* link helpers */ -static inline int ata_port_max_devices (const struct ata_port *ap) +static inline int ata_link_max_devices (const struct ata_link *link) { -if (ap->flags &ATA_FLAG_SLAVE_POSS ) +if (link->ap->flags &ATA_FLAG_SLAVE_POSS )return 2 ;return 1 ; } +#define ata_port_for_each_link (lk, ap) \ + for ((lk) = &(ap)->link; (lk); (lk) = NULL) + +#define ata_link_for_each_dev (dev, link) \ + for ((dev) = (link)->device; \ + (dev) - (link)->device < ata_link_max_devices(link) || (dev = NULL); \ + (dev)++) +static inline u8 ata_chk_status (struct ata_port *ap) {
Signature · 1 line
1.4.2.3
PATCH 6/18 libata-link: linkify PHY-related functions
In reply to Tejun HeoMake the following PHY-related functions to deal with ata_link instead of ata_port.
* sata_print_link_status()
* sata_down_spd_limit()
* ata_set_sata_spd_limit() and friends
* sata_link_debounce/resume()
* sata_scr_valid/read/write/write_flush()
* ata_link_on/offline()
This patch introduces no behavior change.
--- drivers/ata/ahci.c | 6 + drivers/ata/libata-core.c | 231 ++++++++++++++++++++++++--------------------- drivers/ata/libata-eh.c | 24 +++-- drivers/ata/libata-sff.c | 2 drivers/ata/libata.h | 4 - drivers/ata/sata_mv.c | 14 +-- drivers/ata/sata_sil24.c | 10 +- include/linux/libata.h | 19 ++-- 8 files changed, 166 insertions(+), 144 deletions(-)
drivers/ata/ahci.c +3 -3
@@ -747,7 +747,7 @@ static int ahci_softreset(struct ata_porDPRINTK ("ENTER\n" ); -if (ata_port_offline (ap)) { +if (ata_link_offline (&ap->link)) {DPRINTK ("PHY reports no device\n" ); *class =ATA_DEV_NONE ;return 0 ;
@@ -820,7 +820,7 @@ static int ahci_softreset(struct ata_pormsleep (150 ); *class =ATA_DEV_NONE ; -if (ata_port_online (ap)) { +if (ata_link_online (&ap->link)) {if (ata_busy_sleep (ap,ATA_TMOUT_BOOT_QUICK ,ATA_TMOUT_BOOT )) { rc = -EIO ; reason ="device not ready" ;
@@ -861,7 +861,7 @@ static int ahci_hardreset(struct ata_porahci_start_engine (port_mmio); -if (rc ==0 &&ata_port_online (ap)) +if (rc ==0 &&ata_link_online (&ap->link)) *class =ahci_dev_classify (ap);if (*class ==ATA_DEV_UNKNOWN ) *class =ATA_DEV_NONE ;
drivers/ata/libata-core.c +125 -106
650 lines not on this page · raw message
drivers/ata/libata-eh.c +13 -11
@@ -1290,7 +1290,7 @@ static int ata_eh_speed_down(struct ata_return 0 ;/* speed down SATA link speed if possible */ -if (sata_down_spd_limit (dev->link->ap) ==0 ) +if (sata_down_spd_limit (dev->link) ==0 )return ATA_EH_HARDRESET ;/* lower transfer mode */
@@ -1315,7 +1315,8 @@ static int ata_eh_speed_down(struct ata_*/ static void ata_eh_autopsy (struct ata_port *ap) { -struct ata_eh_context *ehc = &ap->link.eh_context; +struct ata_link *link = &ap->link; +struct ata_eh_context *ehc = &link->eh_context;unsigned int all_err_mask =0 ;int tag, is_io =0 ;u32 serror;
@@ -1327,7 +1328,7 @@ static void ata_eh_autopsy(struct ata_poreturn ;/* obtain and analyze SError */ - rc =sata_scr_read (ap,SCR_ERROR , &serror); + rc =sata_scr_read (link,SCR_ERROR , &serror);if (rc ==0 ) { ehc->i.serror |= serror;ata_eh_analyze_serror (ap);
@@ -1515,7 +1516,8 @@ static int ata_eh_reset(struct ata_port ata_prereset_fn_t prereset, ata_reset_fn_t softreset, ata_reset_fn_t hardreset, ata_postreset_fn_t postreset) { - struct ata_eh_context *ehc = &ap->link.eh_context; + struct ata_link *link = &ap->link; +struct ata_eh_context *ehc = &link->eh_context;unsigned int *classes = ehc->classes;int tries =ATA_EH_RESET_TRIES ;int verbose = !(ehc->i.flags &ATA_EHI_QUIET );
@@ -1532,7 +1534,7 @@ static int ata_eh_reset(struct ata_port*/ action = ehc->i.action; ehc->i.action &= ~ATA_EH_RESET_MASK ; -if (softreset && (!hardreset || (!sata_set_spd_needed (ap) && +if (softreset && (!hardreset || (!sata_set_spd_needed (link) && !(action &ATA_EH_HARDRESET )))) ehc->i.action |=ATA_EH_SOFTRESET ;else
@@ -1558,7 +1560,7 @@ static int ata_eh_reset(struct ata_port reset = softreset; else {/* prereset told us not to reset, bang classes and return */ -ata_link_for_each_dev (dev, &ap->link) +ata_link_for_each_dev (dev, link) classes[dev->devno] =ATA_DEV_NONE ;return 0 ; }
@@ -1625,7 +1627,7 @@ static int ata_eh_reset(struct ata_portssleep (5 );if (reset == hardreset) -sata_down_spd_limit (ap); +sata_down_spd_limit (link);if (hardreset) reset = hardreset; goto retry;
@@ -1635,7 +1637,7 @@ static int ata_eh_reset(struct ata_port/* After the reset, the device state is PIO 0 and the * controller state is undefined. Record the mode. */ -ata_link_for_each_dev (dev, &ap->link) +ata_link_for_each_dev (dev, link) dev->pio_mode =XFER_PIO_0 ;if (postreset)
@@ -1663,7 +1665,7 @@ static int ata_eh_revalidate_and_attach(unsigned int action =ata_eh_dev_action (dev);if (action &ATA_EH_REVALIDATE &&ata_dev_ready (dev)) { -if (ata_port_offline (ap)) { +if (ata_link_offline (dev->link)) { rc = -EIO ;break ; }
@@ -1920,7 +1922,7 @@ static void ata_eh_handle_dev_fail(struc ehc->tries[dev->devno] =0 ;break ;case -EIO : -sata_down_spd_limit (ap); +sata_down_spd_limit (&ap->link);default : ehc->tries[dev->devno]--; if (down_xfermask &&
@@ -1933,7 +1935,7 @@ static void ata_eh_handle_dev_fail(strucata_dev_disable (dev);/* detach if offline */ -if (ata_port_offline (ap)) +if (ata_link_offline (&ap->link))ata_eh_detach_dev (dev);/* probe if requested */
drivers/ata/libata-sff.c +1 -1
@@ -776,7 +776,7 @@ void ata_bmdma_error_handler(struct ata_ata_reset_fn_t hardreset; hardreset =NULL ; -if (sata_scr_valid (ap)) +if (sata_scr_valid (&ap->link)) hardreset = sata_std_hardreset; ata_bmdma_drive_eh(ap, ata_std_prereset, ata_std_softreset, hardreset,
drivers/ata/libata.h +2 -2
@@ -54,8 +54,8 @@ extern unsigned int ata_do_simple_cmd(stextern int ata_dev_read_id (struct ata_device *dev,unsigned int *p_class,int post_reset,u16 *id);extern int ata_dev_configure (struct ata_device *dev,int print_info); -extern int sata_down_spd_limit (struct ata_port *ap); -extern int sata_set_spd_needed (struct ata_port *ap); +extern int sata_down_spd_limit (struct ata_link *link); +extern int sata_set_spd_needed (struct ata_link *link);extern int ata_down_xfermask_limit (struct ata_device *dev,int force_pio0);extern int ata_set_mode (struct ata_port *ap,struct ata_device **r_failed_dev);extern void ata_qc_free (struct ata_queued_cmd *qc);
drivers/ata/sata_mv.c +7 -7
@@ -1311,8 +1311,8 @@ static void mv_err_intr(struct ata_port edma_err_cause =readl (port_mmio +EDMA_ERR_IRQ_CAUSE_OFS );if (EDMA_ERR_SERR & edma_err_cause) { -sata_scr_read (ap,SCR_ERROR , &serr); -sata_scr_write_flush (ap,SCR_ERROR , serr); +sata_scr_read (&ap->link,SCR_ERROR , &serr); +sata_scr_write_flush (&ap->link,SCR_ERROR , serr); }if (EDMA_ERR_SELF_DIS & edma_err_cause) {struct mv_port_priv *pp = ap->private_data;
@@ -1951,15 +1951,15 @@ static void __mv_phy_reset(struct ata_po/* Issue COMRESET via SControl */ comreset_retry: -sata_scr_write_flush (ap,SCR_CONTROL ,0x301 ); +sata_scr_write_flush (&ap->link,SCR_CONTROL ,0x301 );__msleep (1 , can_sleep); -sata_scr_write_flush (ap,SCR_CONTROL ,0x300 ); +sata_scr_write_flush (&ap->link,SCR_CONTROL ,0x300 );__msleep (20 , can_sleep); timeout = jiffies +msecs_to_jiffies (200 ); do { - sata_scr_read(ap, SCR_STATUS, &sstatus); + sata_scr_read(&ap->link, SCR_STATUS, &sstatus); if (((sstatus & 0x3) == 3) || ((sstatus & 0x3) == 0)) break;
@@ -1976,10 +1976,10 @@ comreset_retry:"SCtrl 0x%08x\n" ,mv_scr_read (ap,SCR_STATUS ), mv_scr_read(ap, SCR_ERROR), mv_scr_read(ap, SCR_CONTROL)); -if (ata_port_online (ap)) { +if (ata_link_online (&ap->link)) {ata_port_probe (ap); }else { -sata_scr_read (ap,SCR_STATUS , &sstatus); +sata_scr_read (&ap->link,SCR_STATUS , &sstatus);ata_port_printk (ap,KERN_INFO ,"no device found (phy stat %08x)\n" , sstatus);ata_port_disable (ap);
drivers/ata/sata_sil24.c +5 -5
@@ -551,7 +551,7 @@ static int sil24_softreset(struct ata_poDPRINTK ("ENTER\n" ); -if (ata_port_offline (ap)) { +if (ata_link_offline (&ap->link)) {DPRINTK ("PHY reports no device\n" ); *class =ATA_DEV_NONE ; goto out;
@@ -608,10 +608,10 @@ static int sil24_hardreset(struct ata_pou32 tmp;/* sil24 does the right thing(tm) without any protection */ -sata_set_spd (ap); +sata_set_spd (&ap->link); tout_msec =100 ; -if (ata_port_online (ap)) +if (ata_link_online (&ap->link)) tout_msec =5000 ;writel (PORT_CS_DEV_RST , port +PORT_CTRL_STAT );
@@ -621,14 +621,14 @@ static int sil24_hardreset(struct ata_po/* SStatus oscillates between zero and valid status after * DEV_RST, debounce it. */ - rc =sata_phy_debounce (ap, sata_deb_timing_long); + rc =sata_link_debounce (&ap->link, sata_deb_timing_long);if (rc) { reason ="PHY debouncing failed" ; goto err; }if (tmp &PORT_CS_DEV_RST ) { -if (ata_port_offline (ap)) +if (ata_link_offline (&ap->link))return 0 ; reason ="link not ready" ; goto err;
include/linux/libata.h +10 -9
@@ -710,9 +710,10 @@ extern void ata_port_probe(struct ata_poextern void __sata_phy_reset (struct ata_port *ap);extern void sata_phy_reset (struct ata_port *ap);extern void ata_bus_reset (struct ata_port *ap); -extern int sata_set_spd (struct ata_port *ap); -extern int sata_phy_debounce (struct ata_port *ap,const unsigned long *param); -extern int sata_phy_resume (struct ata_port *ap,const unsigned long *param); +extern int sata_set_spd (struct ata_link *link); +extern int sata_link_debounce (struct ata_link *link, +const unsigned long *params); +extern int sata_link_resume (struct ata_link *link,const unsigned long *params);extern int ata_std_prereset (struct ata_port *ap);extern int ata_std_softreset (struct ata_port *ap,unsigned int *classes); extern int sata_port_hardreset(struct ata_port *ap,
@@ -753,12 +754,12 @@ extern int ata_sas_slave_configure(strucextern int ata_sas_queuecmd (struct scsi_cmnd *cmd,void (*done)(struct scsi_cmnd *),struct ata_port *ap);extern unsigned int ata_host_intr (struct ata_port *ap,struct ata_queued_cmd *qc); -extern int sata_scr_valid (struct ata_port *ap); -extern int sata_scr_read (struct ata_port *ap,int reg,u32 *val); -extern int sata_scr_write (struct ata_port *ap,int reg,u32 val); -extern int sata_scr_write_flush (struct ata_port *ap,int reg,u32 val); -extern int ata_port_online (struct ata_port *ap); -extern int ata_port_offline (struct ata_port *ap); +extern int sata_scr_valid (struct ata_link *link); +extern int sata_scr_read (struct ata_link *link,int reg,u32 *val); +extern int sata_scr_write (struct ata_link *link,int reg,u32 val); +extern int sata_scr_write_flush (struct ata_link *link,int reg,u32 val); +extern int ata_link_online (struct ata_link *link); +extern int ata_link_offline (struct ata_link *link);extern int ata_scsi_device_resume (struct scsi_device *);extern int ata_scsi_device_suspend (struct scsi_device *,pm_message_t mesg);extern int ata_host_suspend (struct ata_host *host,pm_message_t mesg);
Signature · 1 line
1.4.2.3
PATCH 7/18 libata-link: linkify EH action helpers
In reply to Tejun HeoMake ata_eh_about_to_do() and ata_eh_done() deal with ata_link instead of ata_port.
This patch introduces no behavior change.
--- drivers/ata/libata-eh.c | 43 ++++++++++++++++++++++--------------------- 1 files changed, 22 insertions(+), 21 deletions(-)
drivers/ata/libata-eh.c +22 -21
@@ -766,23 +766,24 @@ static void ata_eh_detach_dev(struct ata/** * ata_eh_about_to_do - about to perform eh_action -* @ap: target ATA port +* @link: target ATA link * @dev: target ATA dev for per-dev action (can be NULL) * @action: action about to be performed * * Called just before performing EH actions to clear related bits -* in @ap->link.eh_info such that eh actions are not -* unnecessarily repeated. +* in @link->eh_info such that eh actions are not unnecessarily +* repeated. * * LOCKING: * None. */ -static void ata_eh_about_to_do (struct ata_port *ap,struct ata_device *dev, +static void ata_eh_about_to_do (struct ata_link *link,struct ata_device *dev,unsigned int action) { +struct ata_port *ap = link->ap; +struct ata_eh_info *ehi = &link->eh_info; +struct ata_eh_context *ehc = &link->eh_context;unsigned long flags; -struct ata_eh_info *ehi = &ap->link.eh_info; -struct ata_eh_context *ehc = &ap->link.eh_context;spin_lock_irqsave (ap->lock, flags);
@@ -799,7 +800,7 @@ static void ata_eh_about_to_do(struct at ehi->flags &= ~ATA_EHI_RESET_MODIFIER_MASK ; } -ata_eh_clear_action (&ap->link, dev, ehi, action); +ata_eh_clear_action (link, dev, ehi, action);if (!(ehc->i.flags &ATA_EHI_QUIET )) ap->pflags |=ATA_PFLAG_RECOVERED ;
@@ -809,20 +810,20 @@ static void ata_eh_about_to_do(struct at/** * ata_eh_done - EH action complete -* @ap: target ATA port +* @ap: target ATA port * @dev: target ATA dev for per-dev action (can be NULL) * @action: action just completed * * Called right after performing EH actions to clear related bits -* in @ap->link.eh_context. +* in @link->eh_context. * * LOCKING: * None. */ -static void ata_eh_done (struct ata_port *ap,struct ata_device *dev, +static void ata_eh_done (struct ata_link *link,struct ata_device *dev,unsigned int action) { -struct ata_eh_context *ehc = &ap->link.eh_context; +struct ata_eh_context *ehc = &link->eh_context;/* if reset is complete, clear all reset actions & reset modifier */ if (action &ATA_EH_RESET_MASK ) {
@@ -830,7 +831,7 @@ static void ata_eh_done(struct ata_port ehc->i.flags &= ~ATA_EHI_RESET_MODIFIER_MASK ; } -ata_eh_clear_action (&ap->link, dev, &ehc->i, action); +ata_eh_clear_action (link, dev, &ehc->i, action); }/**
@@ -1527,7 +1528,7 @@ static int ata_eh_reset(struct ata_portint did_followup_srst, rc;/* about to reset */ -ata_eh_about_to_do (ap,NULL , ehc->i.action &ATA_EH_RESET_MASK ); +ata_eh_about_to_do (link,NULL , ehc->i.action &ATA_EH_RESET_MASK );/* Determine which reset to use and record in ehc->i.action. * prereset() may examine and modify it.
@@ -1600,7 +1601,7 @@ static int ata_eh_reset(struct ata_portreturn -EINVAL ; } -ata_eh_about_to_do (ap,NULL ,ATA_EH_RESET_MASK ); +ata_eh_about_to_do (link,NULL ,ATA_EH_RESET_MASK ); rc =ata_do_reset (ap, reset, classes); if (rc == 0 && classify &&
@@ -1644,7 +1645,7 @@ static int ata_eh_reset(struct ata_portpostreset (ap, classes);/* reset successful, schedule revalidation */ -ata_eh_done (ap,NULL , ehc->i.action &ATA_EH_RESET_MASK ); +ata_eh_done (link,NULL , ehc->i.action &ATA_EH_RESET_MASK ); ehc->i.action |=ATA_EH_REVALIDATE ; }
@@ -1670,13 +1671,13 @@ static int ata_eh_revalidate_and_attach(break ; } -ata_eh_about_to_do (ap, dev,ATA_EH_REVALIDATE ); +ata_eh_about_to_do (&ap->link, dev,ATA_EH_REVALIDATE ); rc =ata_dev_revalidate (dev, ehc->i.flags &ATA_EHI_DID_RESET );if (rc)break ; -ata_eh_done (ap, dev,ATA_EH_REVALIDATE ); +ata_eh_done (&ap->link, dev,ATA_EH_REVALIDATE );/* schedule the scsi_rescan_device() here */ queue_work (ata_aux_wq, &(ap->scsi_rescan_task));
@@ -1740,7 +1741,7 @@ static int ata_eh_suspend(struct ata_porWARN_ON (dev->flags &ATA_DFLAG_SUSPENDED ); -ata_eh_about_to_do (ap, dev,ATA_EH_SUSPEND ); +ata_eh_about_to_do (&ap->link, dev,ATA_EH_SUSPEND );if (dev->class ==ATA_DEV_ATA && !(action &ATA_EH_PM_FREEZE )) {/* flush cache */
@@ -1763,7 +1764,7 @@ static int ata_eh_suspend(struct ata_por dev->flags |=ATA_DFLAG_SUSPENDED ;spin_unlock_irqrestore (ap->lock, flags); -ata_eh_done (ap, dev,ATA_EH_SUSPEND ); +ata_eh_done (&ap->link, dev,ATA_EH_SUSPEND ); }if (rc)
@@ -1833,7 +1834,7 @@ static int ata_eh_resume(struct ata_portif (!ata_dev_enabled (dev) || !(action &ATA_EH_RESUME ))continue ; -ata_eh_about_to_do (ap, dev,ATA_EH_RESUME ); +ata_eh_about_to_do (&ap->link, dev,ATA_EH_RESUME );if (dev->class ==ATA_DEV_ATA && !(action &ATA_EH_PM_FREEZE )) { err_mask = ata_do_simple_cmd(dev,
@@ -1847,7 +1848,7 @@ static int ata_eh_resume(struct ata_port } } -ata_eh_done (ap, dev,ATA_EH_RESUME ); +ata_eh_done (&ap->link, dev,ATA_EH_RESUME ); }if (rc)
Signature · 1 line
1.4.2.3
PATCH 8/18 libata-link: linkify reset
In reply to Tejun HeoMake reset methods and related functions deal with ata_link instead of ata_port.
* ata_do_reset()
* ata_eh_reset()
* all prereset/reset/postreset methods and related functions
This patch introduces no behavior change.
--- drivers/ata/ahci.c | 30 +++++++++++-------- drivers/ata/ata_generic.c | 8 +++-- drivers/ata/ata_piix.c | 27 +++++++++-------- drivers/ata/libata-core.c | 62 +++++++++++++++++++-------------------- drivers/ata/libata-eh.c | 38 ++++++++++++------------ drivers/ata/pata_ali.c | 16 +++++----- drivers/ata/pata_amd.c | 24 +++++++++------ drivers/ata/pata_artop.c | 12 ++++---- drivers/ata/pata_atiixp.c | 5 ++- drivers/ata/pata_cmd64x.c | 11 ++++--- drivers/ata/pata_cs5520.c | 6 ++-- drivers/ata/pata_cs5530.c | 6 ++-- drivers/ata/pata_cs5535.c | 5 ++- drivers/ata/pata_cypress.c | 6 ++-- drivers/ata/pata_efar.c | 7 +++- drivers/ata/pata_hpt366.c | 5 ++- drivers/ata/pata_hpt37x.c | 12 ++++---- drivers/ata/pata_hpt3x2n.c | 7 +++- drivers/ata/pata_hpt3x3.c | 6 ++-- drivers/ata/pata_it821x.c | 8 +++-- drivers/ata/pata_jmicron.c | 9 +++--- drivers/ata/pata_mpiix.c | 5 ++- drivers/ata/pata_netcell.c | 8 +++-- drivers/ata/pata_ns87410.c | 7 +++- drivers/ata/pata_oldpiix.c | 7 +++- drivers/ata/pata_opti.c | 7 +++- drivers/ata/pata_optidma.c | 7 +++- drivers/ata/pata_pdc2027x.c | 10 +++--- drivers/ata/pata_pdc202xx_old.c | 13 ++++---- drivers/ata/pata_radisys.c | 8 +++-- drivers/ata/pata_rz1000.c | 8 +++-- drivers/ata/pata_serverworks.c | 8 +++-- drivers/ata/pata_sil680.c | 13 ++++---- drivers/ata/pata_sis.c | 21 ++++++++----- drivers/ata/pata_sl82c105.c | 5 ++- drivers/ata/pata_triflex.c | 7 +++- drivers/ata/pata_via.c | 5 ++- drivers/ata/sata_nv.c | 4 +-- drivers/ata/sata_sil24.c | 20 +++++++------ drivers/ata/sata_via.c | 5 ++- include/linux/libata.h | 17 ++++++----- 41 files changed, 267 insertions(+), 228 deletions(-)
drivers/ata/ahci.c +17 -13
@@ -733,8 +733,9 @@ static int ahci_clo(struct ata_port *ap)return 0 ; } -static int ahci_softreset (struct ata_port *ap,unsigned int *class) +static int ahci_softreset (struct ata_link *link,unsigned int *class) { +struct ata_port *ap = link->ap;struct ahci_port_priv *pp = ap->private_data;void __iomem *mmio = ap->host->mmio_base;void __iomem *port_mmio =ahci_port_base (mmio, ap->port_no);
@@ -747,7 +748,7 @@ static int ahci_softreset(struct ata_porDPRINTK ("ENTER\n" ); -if (ata_link_offline (&ap->link)) { +if (ata_link_offline (link)) {DPRINTK ("PHY reports no device\n" ); *class =ATA_DEV_NONE ;return 0 ;
@@ -776,7 +777,7 @@ static int ahci_softreset(struct ata_por/* restart engine */ ahci_start_engine (port_mmio); -ata_tf_init (ap->link.device, &tf); +ata_tf_init (link->device, &tf); fis = pp->cmd_tbl;/* issue the first D2H Register FIS */
@@ -820,7 +821,7 @@ static int ahci_softreset(struct ata_pormsleep (150 ); *class =ATA_DEV_NONE ; -if (ata_link_online (&ap->link)) { +if (ata_link_online (link)) {if (ata_busy_sleep (ap,ATA_TMOUT_BOOT_QUICK ,ATA_TMOUT_BOOT )) { rc = -EIO ; reason ="device not ready" ;
@@ -835,12 +836,13 @@ static int ahci_softreset(struct ata_por fail_restart:ahci_start_engine (port_mmio); fail: -ata_port_printk (ap,KERN_ERR ,"softreset failed (%s)\n" , reason); +ata_link_printk (link,KERN_ERR ,"softreset failed (%s)\n" , reason);return rc; } -static int ahci_hardreset (struct ata_port *ap,unsigned int *class) +static int ahci_hardreset (struct ata_link *link,unsigned int *class) { +struct ata_port *ap = link->ap;struct ahci_port_priv *pp = ap->private_data;u8 *d2h_fis = pp->rx_fis +RX_FIS_D2H_REG ;struct ata_taskfile tf;
@@ -853,15 +855,15 @@ static int ahci_hardreset(struct ata_porahci_stop_engine (port_mmio);/* clear D2H reception area to properly wait for D2H FIS */ -ata_tf_init (ap->link.device, &tf); +ata_tf_init (link->device, &tf); tf.command =0xff ;ata_tf_to_fis (&tf, d2h_fis,0 ); - rc =sata_std_hardreset (ap, class); + rc =sata_std_hardreset (link, class);ahci_start_engine (port_mmio); -if (rc ==0 &&ata_link_online (&ap->link)) +if (rc ==0 &&ata_link_online (link)) *class =ahci_dev_classify (ap);if (*class ==ATA_DEV_UNKNOWN ) *class =ATA_DEV_NONE ;
@@ -870,8 +872,9 @@ static int ahci_hardreset(struct ata_porreturn rc; } -static int ahci_vt8251_hardreset (struct ata_port *ap,unsigned int *class) +static int ahci_vt8251_hardreset (struct ata_link *link,unsigned int *class) { +struct ata_port *ap = link->ap;void __iomem *mmio = ap->host->mmio_base;void __iomem *port_mmio =ahci_port_base (mmio, ap->port_no);int rc;
@@ -880,7 +883,7 @@ static int ahci_vt8251_hardreset(structahci_stop_engine (port_mmio); - rc =sata_port_hardreset (ap,sata_ehc_deb_timing (&ap->link.eh_context)); + rc =sata_link_hardreset (link,sata_ehc_deb_timing (&link->eh_context));/* vt8251 needs SError cleared for the port to operate */ ahci_scr_write (ap,SCR_ERROR ,ahci_scr_read (ap,SCR_ERROR ));
@@ -895,12 +898,13 @@ static int ahci_vt8251_hardreset(structreturn rc ?: -EAGAIN ; } -static void ahci_postreset (struct ata_port *ap,unsigned int *class) +static void ahci_postreset (struct ata_link *link,unsigned int *class) { +struct ata_port *ap = link->ap;void __iomem *port_mmio = (void __iomem *) ap->ioaddr.cmd_addr;u32 new_tmp, tmp; -ata_std_postreset (ap, class); +ata_std_postreset (link, class);/* Make sure port's ATAPI bit is set appropriately */ new_tmp = tmp =readl (port_mmio +PORT_CMD );
drivers/ata/ata_generic.c +4 -4
@@ -34,15 +34,15 @@ #define DRV_VERSION "0.2.7"/** * generic_pre_reset - probe begin -* @ap: ATA port +* @link: ATA link * * Set up cable type and use generic probe init */ -static int generic_pre_reset (struct ata_port *ap) +static int generic_pre_reset (struct ata_link *link) { - ap->cbl =ATA_CBL_PATA80 ; -return ata_std_prereset (ap); + link->ap->cbl =ATA_CBL_PATA80 ; +return ata_std_prereset (link); }
drivers/ata/ata_piix.c +15 -12
@@ -662,21 +662,22 @@ cbl40:/** * piix_pata_prereset - prereset for PATA host controller -* @ap: Target port +* @link: Target link * * * LOCKING: * None (inherited from caller). */ -static int piix_pata_prereset (struct ata_port *ap) +static int piix_pata_prereset (struct ata_link *link) { +struct ata_port *ap = link->ap;struct pci_dev *pdev =to_pci_dev (ap->host->dev);if (!pci_test_config_bits (pdev, &piix_enable_bits[ap->port_no]))return -ENOENT ; ap->cbl =ATA_CBL_PATA40 ; -return ata_std_prereset (ap); +return ata_std_prereset (link); }static void piix_pata_error_handler (struct ata_port *ap)
@@ -688,25 +689,26 @@ static void piix_pata_error_handler(stru/** * ich_pata_prereset - prereset for PATA host controller -* @ap: Target port +* @link: Target link * * * LOCKING: * None (inherited from caller). */ -static int ich_pata_prereset (struct ata_port *ap) +static int ich_pata_prereset (struct ata_link *link) { +struct ata_port *ap = link->ap;struct pci_dev *pdev =to_pci_dev (ap->host->dev);if (!pci_test_config_bits (pdev, &piix_enable_bits[ap->port_no])) {ata_port_printk (ap,KERN_INFO ,"port disabled. ignoring.\n" ); - ap->link.eh_context.i.action &= ~ATA_EH_RESET_MASK ; + link->eh_context.i.action &= ~ATA_EH_RESET_MASK ;return 0 ; }ich_pata_cbl_detect (ap); -return ata_std_prereset (ap); +return ata_std_prereset (link); }static void ich_pata_error_handler (struct ata_port *ap)
@@ -758,10 +760,10 @@ static unsigned int piix_sata_present_ma/** * piix_sata_softreset - reset SATA host port via ATA SRST -* @ap: port to reset +* @link: link to reset * @classes: resulting classes of attached devices * -* Reset SATA host port via ATA SRST. On controllers with +* Reset SATA host link via ATA SRST. On controllers with * reliable PCS present bits, the bits are used to determine * device presence. *
@@ -771,19 +773,20 @@ static unsigned int piix_sata_present_ma* RETURNS: * 0 on success, -errno otherwise. */ -static int piix_sata_softreset (struct ata_port *ap,unsigned int *classes) +static int piix_sata_softreset (struct ata_link *link,unsigned int *classes) { +struct ata_port *ap = link->ap;unsigned int present_mask;struct ata_device *dev;int rc; present_mask =piix_sata_present_mask (ap); - rc =ata_std_softreset (ap, classes); + rc =ata_std_softreset (link, classes);if (rc)return rc; -ata_link_for_each_dev (dev, &ap->link) { +ata_link_for_each_dev (dev, link) {if (!(present_mask & (1 << dev->devno))) classes[dev->devno] =ATA_DEV_NONE ; }
drivers/ata/libata-core.c +30 -32
180 lines not on this page · raw message
drivers/ata/libata-eh.c +19 -19
@@ -1470,16 +1470,16 @@ static void ata_eh_report(struct ata_por } } -static int ata_do_reset (struct ata_port *ap,ata_reset_fn_t reset, +static int ata_do_reset (struct ata_link *link,ata_reset_fn_t reset,unsigned int *classes) {struct ata_device *dev;int rc; -ata_link_for_each_dev (dev, &ap->link) +ata_link_for_each_dev (dev, link) classes[dev->devno] =ATA_DEV_UNKNOWN ; - rc =reset (ap, classes); + rc =reset (link, classes);if (rc)return rc;
@@ -1487,12 +1487,12 @@ static int ata_do_reset(struct ata_port* is complete and convert all ATA_DEV_UNKNOWN to * ATA_DEV_NONE. */ -ata_link_for_each_dev (dev, &ap->link) +ata_link_for_each_dev (dev, link)if (classes[dev->devno] !=ATA_DEV_UNKNOWN )break ;if (dev) { -ata_link_for_each_dev (dev, &ap->link) { +ata_link_for_each_dev (dev, link) {if (classes[dev->devno] ==ATA_DEV_UNKNOWN ) classes[dev->devno] =ATA_DEV_NONE ; }
@@ -1513,11 +1513,10 @@ static int ata_eh_followup_srst_needed(ireturn 0 ; } -static int ata_eh_reset (struct ata_port *ap,int classify, +static int ata_eh_reset (struct ata_link *link,int classify,ata_prereset_fn_t prereset,ata_reset_fn_t softreset,ata_reset_fn_t hardreset,ata_postreset_fn_t postreset) { -struct ata_link *link = &ap->link;struct ata_eh_context *ehc = &link->eh_context;unsigned int *classes = ehc->classes;int tries =ATA_EH_RESET_TRIES ;
@@ -1542,13 +1541,14 @@ static int ata_eh_reset(struct ata_port ehc->i.action |=ATA_EH_HARDRESET ;if (prereset) { - rc =prereset (ap); + rc =prereset (link);if (rc) {if (rc == -ENOENT ) { -ata_port_printk (ap,KERN_DEBUG ,"port disabled. ignoring.\n" ); +ata_link_printk (link,KERN_DEBUG , +"link disabled. ignoring.\n" ); ehc->i.action &= ~ATA_EH_RESET_MASK ; }else -ata_port_printk (ap,KERN_ERR , +ata_link_printk (link,KERN_ERR ,"prereset failed (errno=%d)\n" , rc);return rc; }
@@ -1568,7 +1568,7 @@ static int ata_eh_reset(struct ata_port/* did prereset() screw up? if so, fix up to avoid oopsing */ if (!reset) { -ata_port_printk (ap,KERN_ERR ,"BUG: prereset() requested " +ata_link_printk (link,KERN_ERR ,"BUG: prereset() requested " "invalid reset type\n" );if (softreset) reset = softreset;
@@ -1579,13 +1579,13 @@ static int ata_eh_reset(struct ata_port retry:/* shut up during boot probing */ if (verbose) -ata_port_printk (ap,KERN_INFO ,"%s resetting port\n" , +ata_link_printk (link,KERN_INFO ,"%s resetting port\n" , reset == softreset ?"soft" :"hard" );/* mark that this EH session started with reset */ ehc->i.flags |=ATA_EHI_DID_RESET ; - rc =ata_do_reset (ap, reset, classes); + rc =ata_do_reset (link, reset, classes); did_followup_srst =0 ; if (reset == hardreset &&
@@ -1595,18 +1595,18 @@ static int ata_eh_reset(struct ata_port reset = softreset;if (!reset) { -ata_port_printk (ap,KERN_ERR , +ata_link_printk (link,KERN_ERR ,"follow-up softreset required " "but no softreset avaliable\n" );return -EINVAL ; }ata_eh_about_to_do (link,NULL ,ATA_EH_RESET_MASK ); - rc =ata_do_reset (ap, reset, classes); + rc =ata_do_reset (link, reset, classes);if (rc ==0 && classify && classes[0 ] ==ATA_DEV_UNKNOWN ) { -ata_port_printk (ap,KERN_ERR , +ata_link_printk (link,KERN_ERR ,"classification failed\n" );return -EINVAL ; }
@@ -1623,7 +1623,7 @@ static int ata_eh_reset(struct ata_port }else type ="hard" ; -ata_port_printk (ap,KERN_WARNING , +ata_link_printk (link,KERN_WARNING ,"%sreset failed, retrying in 5 secs\n" , type);ssleep (5 );
@@ -1642,7 +1642,7 @@ static int ata_eh_reset(struct ata_port dev->pio_mode =XFER_PIO_0 ;if (postreset) -postreset (ap, classes); +postreset (link, classes);/* reset successful, schedule revalidation */ ata_eh_done (link,NULL , ehc->i.action &ATA_EH_RESET_MASK );
@@ -2029,7 +2029,7 @@ static int ata_eh_recover(struct ata_porif (ehc->i.action &ATA_EH_RESET_MASK ) {ata_eh_freeze_port (ap); - rc =ata_eh_reset (ap,ata_port_nr_vacant (ap), prereset, + rc =ata_eh_reset (&ap->link,ata_port_nr_vacant (ap), prereset, softreset, hardreset, postreset);if (rc) { ata_port_printk(ap, KERN_ERR,
drivers/ata/pata_ali.c +8 -8
@@ -91,15 +91,15 @@ static int ali_c2_cable_detect(struct at/** * ali_early_error_handler - reset for eary chip -* @ap: ATA port +* @link: ATA link * * Handle the reset callback for the later chips with cable detect */ -static int ali_c2_pre_reset (struct ata_port *ap) +static int ali_c2_pre_reset (struct ata_link *link) { - ap->cbl =ali_c2_cable_detect (ap); -return ata_std_prereset (ap); + link->ap->cbl =ali_c2_cable_detect (link->ap); +return ata_std_prereset (link); }static void ali_c2_error_handler (struct ata_port *ap)
@@ -124,15 +124,15 @@ static int ali_early_cable_detect(struct/** * ali_early_probe_init - reset for early chip -* @ap: ATA port +* @link: ATA link * * Handle the reset callback for the early (pre cable detect) chips. */ -static int ali_early_pre_reset (struct ata_port *ap) +static int ali_early_pre_reset (struct ata_link *link) { - ap->cbl =ali_early_cable_detect (ap); -return ata_std_prereset (ap); + link->ap->cbl =ali_early_cable_detect (link->ap); +return ata_std_prereset (link); }static void ali_early_error_handler (struct ata_port *ap)
drivers/ata/pata_amd.c +14 -10
@@ -119,14 +119,14 @@ static void timing_setup(struct ata_port }/** -* amd_probe_init - cable detection -* @ap: ATA port +* amd_pre_reset - cable detection +* @link: ATA link * * Perform cable detection. The BIOS stores this in PCI config * space for us. */ -static int amd_pre_reset (struct ata_port *ap) +static int amd_pre_reset (struct ata_link *link) {static const u32 bitmask[2 ] = {0x03 ,0xC0 };static const struct pci_bits amd_enable_bits[] = {
@@ -134,6 +134,7 @@ static int amd_pre_reset(struct ata_port { 0x40, 1, 0x01, 0x01 } }; +struct ata_port *ap = link->ap;struct pci_dev *pdev =to_pci_dev (ap->host->dev);u8 ata66;
@@ -145,7 +146,7 @@ static int amd_pre_reset(struct ata_port ap->cbl =ATA_CBL_PATA80 ; else ap->cbl = ATA_CBL_PATA40; -return ata_std_prereset (ap); +return ata_std_prereset (link); }
@@ -156,20 +157,22 @@ static void amd_error_handler(struct ata ata_std_postreset); } -static int amd_early_pre_reset (struct ata_port *ap) +static int amd_early_pre_reset (struct ata_link *link) { -struct pci_dev *pdev =to_pci_dev (ap->host->dev);static struct pci_bits amd_enable_bits[] = { {0x40 ,1 ,0x02 ,0x02 }, {0x40 ,1 ,0x01 ,0x01 } }; +struct ata_port *ap = link->ap; +struct pci_dev *pdev =to_pci_dev (ap->host->dev); +if (!pci_test_config_bits (pdev, &amd_enable_bits[ap->port_no]))return -ENOENT ;/* No host side cable detection */ ap->cbl =ATA_CBL_PATA80 ; -return ata_std_prereset (ap); +return ata_std_prereset (link); }
@@ -240,19 +243,20 @@ static void amd133_set_dmamode(struct at/** * nv_probe_init - cable detection -* @ap: ATA port +* @link: ATA link * * Perform cable detection. The BIOS stores this in PCI config * space for us. */ -static int nv_pre_reset (struct ata_port *ap) { +static int nv_pre_reset (struct ata_link *link) {static const u8 bitmask[2 ] = {0x03 ,0xC0 };static const struct pci_bits nv_enable_bits[] = { {0x50 ,1 ,0x02 ,0x02 }, {0x50 ,1 ,0x01 ,0x01 } }; +struct ata_port *ap = link->ap;struct pci_dev *pdev =to_pci_dev (ap->host->dev);u8 ata66;u16 udma;
@@ -272,7 +276,7 @@ static int nv_pre_reset(struct ata_portpci_read_config_word (pdev,0x62 -2 * ap->port_no, &udma);if ((udma &0xC4 ) ==0xC4 || (udma &0xC400 ) ==0xC400 ) ap->cbl =ATA_CBL_PATA80 ; -return ata_std_prereset (ap); +return ata_std_prereset (link); }static void nv_error_handler (struct ata_port *ap)
drivers/ata/pata_artop.c +7 -5
@@ -39,8 +39,9 @@ #define DRV_VERSION "0.4.2"static int clock =0 ; -static int artop6210_pre_reset (struct ata_port *ap) +static int artop6210_pre_reset (struct ata_link *link) { +struct ata_port *ap = link->ap;struct pci_dev *pdev =to_pci_dev (ap->host->dev);const struct pci_bits artop_enable_bits[] = { {0x4AU ,1U ,0x02UL ,0x02UL },/* port 0 */
@@ -51,7 +52,7 @@ static int artop6210_pre_reset(struct atreturn -ENOENT ; ap->cbl =ATA_CBL_PATA40 ; -return ata_std_prereset (ap); +return ata_std_prereset (link); }/**
@@ -71,19 +72,20 @@ static void artop6210_error_handler(stru/** * artop6260_pre_reset - check for 40/80 pin -* @ap: Port +* @link: link * * The ARTOP hardware reports the cable detect bits in register 0x49. * Nothing complicated needed here. */ -static int artop6260_pre_reset (struct ata_port *ap) +static int artop6260_pre_reset (struct ata_link *link) {static const struct pci_bits artop_enable_bits[] = { {0x4AU ,1U ,0x02UL ,0x02UL },/* port 0 */ {0x4AU ,1U ,0x04UL ,0x04UL },/* port 1 */ }; +struct ata_port *ap = link->ap;struct pci_dev *pdev =to_pci_dev (ap->host->dev);u8 tmp;
@@ -96,7 +98,7 @@ static int artop6260_pre_reset(struct at ap->cbl =ATA_CBL_PATA40 ; else ap->cbl = ATA_CBL_PATA80; -return ata_std_prereset (ap); +return ata_std_prereset (link); }/**
drivers/ata/pata_atiixp.c +3 -2
@@ -33,8 +33,9 @@ enum {ATIIXP_IDE_UDMA_MODE =0x56 }; -static int atiixp_pre_reset (struct ata_port *ap) +static int atiixp_pre_reset (struct ata_link *link) { +struct ata_port *ap = link->ap;struct pci_dev *pdev =to_pci_dev (ap->host->dev);static struct pci_bits atiixp_enable_bits[] = { {0x48 ,1 ,0x01 ,0x00 },
@@ -45,7 +46,7 @@ static int atiixp_pre_reset(struct ata_preturn -ENOENT ; ap->cbl =ATA_CBL_PATA80 ; -return ata_std_prereset (ap); +return ata_std_prereset (link); }static void atiixp_error_handler (struct ata_port *ap)
drivers/ata/pata_cmd64x.c +6 -5
@@ -75,14 +75,15 @@ enum { DTPR1 = 0x7C }; -static int cmd64x_pre_reset (struct ata_port *ap) +static int cmd64x_pre_reset (struct ata_link *link) { - ap->cbl =ATA_CBL_PATA40 ; -return ata_std_prereset (ap); + link->ap->cbl =ATA_CBL_PATA40 ; +return ata_std_prereset (link); } -static int cmd648_pre_reset (struct ata_port *ap) +static int cmd648_pre_reset (struct ata_link *link) { +struct ata_port *ap = link->ap;struct pci_dev *pdev =to_pci_dev (ap->host->dev);u8 r;
@@ -93,7 +94,7 @@ static int cmd648_pre_reset(struct ata_pelse ap->cbl =ATA_CBL_PATA40 ; -return ata_std_prereset (ap); +return ata_std_prereset (link); }static void cmd64x_error_handler (struct ata_port *ap)
drivers/ata/pata_cs5520.c +3 -3
@@ -140,10 +140,10 @@ static void cs5520_set_piomode(struct at } -static int cs5520_pre_reset (struct ata_port *ap) +static int cs5520_pre_reset (struct ata_link *link) { - ap->cbl =ATA_CBL_PATA40 ; -return ata_std_prereset (ap); + link->ap->cbl =ATA_CBL_PATA40 ; +return ata_std_prereset (link); }static void cs5520_error_handler (struct ata_port *ap)
drivers/ata/pata_cs5530.c +3 -3
@@ -153,10 +153,10 @@ static unsigned int cs5530_qc_issue_protreturn ata_qc_issue_prot (qc); } -static int cs5530_pre_reset (struct ata_port *ap) +static int cs5530_pre_reset (struct ata_link *link) { - ap->cbl =ATA_CBL_PATA40 ; -return ata_std_prereset (ap); + link->ap->cbl =ATA_CBL_PATA40 ; +return ata_std_prereset (link); }static void cs5530_error_handler (struct ata_port *ap)
drivers/ata/pata_cs5535.c +3 -2
@@ -77,9 +77,10 @@ #define CS5535_BAD_PIO(timings) ( (timin* cable type. */ -static int cs5535_pre_reset (struct ata_port *ap) +static int cs5535_pre_reset (struct ata_link *link) {u8 cable; +struct ata_port *ap = link->ap;struct pci_dev *pdev =to_pci_dev (ap->host->dev);pci_read_config_byte (pdev,CS5535_CABLE_DETECT , &cable);
@@ -87,7 +88,7 @@ static int cs5535_pre_reset(struct ata_p ap->cbl =ATA_CBL_PATA80 ; else ap->cbl = ATA_CBL_PATA40; -return ata_std_prereset (ap); +return ata_std_prereset (link); }/**
drivers/ata/pata_cypress.c +3 -3
@@ -41,10 +41,10 @@ enum { CY82_INDEX_TIMEOUT = 0x32 }; -static int cy82c693_pre_reset (struct ata_port *ap) +static int cy82c693_pre_reset (struct ata_link *link) { - ap->cbl =ATA_CBL_PATA40 ; -return ata_std_prereset (ap); + link->ap->cbl =ATA_CBL_PATA40 ; +return ata_std_prereset (link); }static void cy82c693_error_handler (struct ata_port *ap)
drivers/ata/pata_efar.c +4 -3
@@ -26,19 +26,20 @@ #define DRV_VERSION "0.4.2"/** * efar_pre_reset - check for 40/80 pin -* @ap: Port +* @link: ATA link * * Perform cable detection for the EFAR ATA interface. This is * different to the PIIX arrangement */ -static int efar_pre_reset (struct ata_port *ap) +static int efar_pre_reset (struct ata_link *link) {static const struct pci_bits efar_enable_bits[] = { {0x41U ,1U ,0x80UL ,0x80UL },/* port 0 */ {0x43U ,1U ,0x80UL ,0x80UL },/* port 1 */ }; +struct ata_port *ap = link->ap;struct pci_dev *pdev =to_pci_dev (ap->host->dev);u8 tmp;
@@ -50,7 +51,7 @@ static int efar_pre_reset(struct ata_por ap->cbl =ATA_CBL_PATA40 ; else ap->cbl = ATA_CBL_PATA80; -return ata_std_prereset (ap); +return ata_std_prereset (link); }/**
drivers/ata/pata_hpt366.c +3 -2
@@ -220,9 +220,10 @@ static u32 hpt36x_find_mode(struct ata_preturn 0xffffffffU ;/* silence compiler warning */ } -static int hpt36x_pre_reset (struct ata_port *ap) +static int hpt36x_pre_reset (struct ata_link *link) {u8 ata66; +struct ata_port *ap = link->ap;struct pci_dev *pdev =to_pci_dev (ap->host->dev);pci_read_config_byte (pdev,0x5A , &ata66);
@@ -230,7 +231,7 @@ static int hpt36x_pre_reset(struct ata_p ap->cbl =ATA_CBL_PATA40 ; else ap->cbl = ATA_CBL_PATA80; -return ata_std_prereset (ap); +return ata_std_prereset (link); }/**
drivers/ata/pata_hpt37x.c +7 -5
@@ -444,14 +444,15 @@ static unsigned long hpt370a_filter(cons/** * hpt37x_pre_reset - reset the hpt37x bus -* @ap: ATA port to reset +* @link: ATA link to reset * * Perform the initial reset handling for the 370/372 and 374 func 0 */ -static int hpt37x_pre_reset (struct ata_port *ap) +static int hpt37x_pre_reset (struct ata_link *link) {u8 scr2, ata66; +struct ata_port *ap = link->ap;struct pci_dev *pdev =to_pci_dev (ap->host->dev);pci_read_config_byte (pdev,0x5B , &scr2);
@@ -471,7 +472,7 @@ static int hpt37x_pre_reset(struct ata_ppci_write_config_byte (pdev,0x54 ,0x37 );udelay (100 ); -return ata_std_prereset (ap); +return ata_std_prereset (link); }/**
@@ -486,11 +487,12 @@ static void hpt37x_error_handler(structata_bmdma_drive_eh (ap, hpt37x_pre_reset, ata_std_softreset,NULL , ata_std_postreset); } -static int hpt374_pre_reset (struct ata_port *ap) +static int hpt374_pre_reset (struct ata_link *link) {u16 mcr3, mcr6;u8 ata66; +struct ata_port *ap = link->ap;struct pci_dev *pdev =to_pci_dev (ap->host->dev);/* Do the extra channel work */ pci_read_config_word (pdev,0x52 , &mcr3);
@@ -515,7 +517,7 @@ static int hpt374_pre_reset(struct ata_ppci_write_config_byte (pdev,0x54 ,0x37 );udelay (100 ); -return ata_std_prereset (ap); +return ata_std_prereset (link); }/**
drivers/ata/pata_hpt3x2n.c +4 -3
@@ -116,15 +116,16 @@ static u32 hpt3x2n_find_mode(struct ata_/** * hpt3x2n_pre_reset - reset the hpt3x2n bus -* @ap: ATA port to reset +* @link: ATA link to reset * * Perform the initial reset handling for the 3x2n series controllers. * Reset the hardware and state machine, obtain the cable type. */ -static int hpt3xn_pre_reset (struct ata_port *ap) +static int hpt3xn_pre_reset (struct ata_link *link) {u8 scr2, ata66; +struct ata_port *ap = link->ap;struct pci_dev *pdev =to_pci_dev (ap->host->dev);pci_read_config_byte (pdev,0x5B , &scr2);
@@ -144,7 +145,7 @@ static int hpt3xn_pre_reset(struct ata_ppci_write_config_byte (pdev,0x54 ,0x37 );udelay (100 ); -return ata_std_prereset (ap); +return ata_std_prereset (link); }/**
drivers/ata/pata_hpt3x3.c +3 -3
@@ -25,10 +25,10 @@ #include <linux/libata.h>#define DRV_NAME "pata_hpt3x3"#define DRV_VERSION "0.4.1" -static int hpt3x3_probe_init (struct ata_port *ap) +static int hpt3x3_probe_init (struct ata_link *link) { - ap->cbl =ATA_CBL_PATA40 ; -return ata_std_prereset (ap); + link->ap->cbl =ATA_CBL_PATA40 ; +return ata_std_prereset (link); }/**
drivers/ata/pata_it821x.c +4 -4
@@ -114,15 +114,15 @@ static int it8212_noraid;/** * it821x_pre_reset - probe -* @ap: ATA port +* @link: ATA link * * Set the cable type */ -static int it821x_pre_reset (struct ata_port *ap) +static int it821x_pre_reset (struct ata_link *link) { - ap->cbl =ATA_CBL_PATA80 ; -return ata_std_prereset (ap); + link->ap->cbl =ATA_CBL_PATA80 ; +return ata_std_prereset (link); }/**
drivers/ata/pata_jmicron.c +5 -4
@@ -29,18 +29,19 @@ typedef enum {/** * jmicron_pre_reset - check for 40/80 pin -* @ap: Port +* @link: ATA link * * Perform the PATA port setup we need. - +* * On the Jmicron 361/363 there is a single PATA port that can be mapped * either as primary or secondary (or neither). We don't do any policy * and setup here. We assume that has been done by init_one and the * BIOS. */ -static int jmicron_pre_reset (struct ata_port *ap) +static int jmicron_pre_reset (struct ata_link *link) { +struct ata_port *ap = link->ap;struct pci_dev *pdev =to_pci_dev (ap->host->dev);u32 control;u32 control5;
@@ -102,7 +103,7 @@ static int jmicron_pre_reset(struct ata_ ap->cbl =ATA_CBL_SATA ;break ; } -return ata_std_prereset (ap); +return ata_std_prereset (link); }/**
drivers/ata/pata_mpiix.c +3 -2
@@ -46,8 +46,9 @@ enum {SECONDARY = (1 <<14 ) }; -static int mpiix_pre_reset (struct ata_port *ap) +static int mpiix_pre_reset (struct ata_link *link) { +struct ata_port *ap = link->ap;struct pci_dev *pdev =to_pci_dev (ap->host->dev);static const struct pci_bits mpiix_enable_bits[] = { {0x6D ,1 ,0x80 ,0x80 },
@@ -57,7 +58,7 @@ static int mpiix_pre_reset(struct ata_poif (!pci_test_config_bits (pdev, &mpiix_enable_bits[ap->port_no]))return -ENOENT ; ap->cbl =ATA_CBL_PATA40 ; -return ata_std_prereset (ap); +return ata_std_prereset (link); }/**
drivers/ata/pata_netcell.c +4 -4
@@ -20,15 +20,15 @@ #define DRV_VERSION "0.1.5"/** * netcell_probe_init - check for 40/80 pin -* @ap: Port +* @link: ATA link * * Cables are handled by the RAID controller. Report 80 pin. */ -static int netcell_pre_reset (struct ata_port *ap) +static int netcell_pre_reset (struct ata_link *link) { - ap->cbl =ATA_CBL_PATA80 ; -return ata_std_prereset (ap); + link->ap->cbl =ATA_CBL_PATA80 ; +return ata_std_prereset (link); }/**
drivers/ata/pata_ns87410.c +4 -3
@@ -32,13 +32,14 @@ #define DRV_VERSION "0.4.2"/** * ns87410_pre_reset - probe begin -* @ap: ATA port +* @link: ATA link * * Set up cable type and use generic probe init */ -static int ns87410_pre_reset (struct ata_port *ap) +static int ns87410_pre_reset (struct ata_link *link) { +struct ata_port *ap = link->ap;struct pci_dev *pdev =to_pci_dev (ap->host->dev);static const struct pci_bits ns87410_enable_bits[] = { {0x43 ,1 ,0x08 ,0x08 },
@@ -48,7 +49,7 @@ static int ns87410_pre_reset(struct ata_if (!pci_test_config_bits (pdev, &ns87410_enable_bits[ap->port_no]))return -ENOENT ; ap->cbl =ATA_CBL_PATA40 ; -return ata_std_prereset (ap); +return ata_std_prereset (link); }/**
drivers/ata/pata_oldpiix.c +4 -3
@@ -29,13 +29,14 @@ #define DRV_VERSION "0.5.2"/** * oldpiix_pre_reset - probe begin -* @ap: ATA port +* @link: ATA link * * Set up cable type and use generic probe init */ -static int oldpiix_pre_reset (struct ata_port *ap) +static int oldpiix_pre_reset (struct ata_link *link) { +struct ata_port *ap = link->ap;struct pci_dev *pdev =to_pci_dev (ap->host->dev);static const struct pci_bits oldpiix_enable_bits[] = { {0x41U ,1U ,0x80UL ,0x80UL },/* port 0 */
@@ -45,7 +46,7 @@ static int oldpiix_pre_reset(struct ata_if (!pci_test_config_bits (pdev, &oldpiix_enable_bits[ap->port_no]))return -ENOENT ; ap->cbl =ATA_CBL_PATA40 ; -return ata_std_prereset (ap); +return ata_std_prereset (link); }/**
drivers/ata/pata_opti.c +4 -3
@@ -46,13 +46,14 @@ enum {/** * opti_pre_reset - probe begin -* @ap: ATA port +* @link: ATA link * * Set up cable type and use generic probe init */ -static int opti_pre_reset (struct ata_port *ap) +static int opti_pre_reset (struct ata_link *link) { +struct ata_port *ap = link->ap;struct pci_dev *pdev =to_pci_dev (ap->host->dev);static const struct pci_bits opti_enable_bits[] = { {0x45 ,1 ,0x80 ,0x00 },
@@ -63,7 +64,7 @@ static int opti_pre_reset(struct ata_porreturn -ENOENT ; ap->cbl =ATA_CBL_PATA40 ; -return ata_std_prereset (ap); +return ata_std_prereset (link); }/**
drivers/ata/pata_optidma.c +4 -3
@@ -47,13 +47,14 @@ static int pci_clock; /* 0 = 33 1 = 25 */** * optidma_pre_reset - probe begin -* @ap: ATA port +* @link: ATA link * * Set up cable type and use generic probe init */ -static int optidma_pre_reset (struct ata_port *ap) +static int optidma_pre_reset (struct ata_link *link) { +struct ata_port *ap = link->ap;struct pci_dev *pdev =to_pci_dev (ap->host->dev);static const struct pci_bits optidma_enable_bits = {0x40 ,1 ,0x08 ,0x00
@@ -63,7 +64,7 @@ static int optidma_pre_reset(struct ata_return -ENOENT ; ap->cbl =ATA_CBL_PATA40 ; -return ata_std_prereset (ap); +return ata_std_prereset (link); }/**
drivers/ata/pata_pdc2027x.c +5 -5
@@ -301,7 +301,7 @@ static inline int pdc2027x_port_enabled(/** * pdc2027x_prereset - prereset for PATA host controller -* @ap: Target port +* @link: Target link * * Probeinit including cable detection. *
@@ -309,13 +309,13 @@ static inline int pdc2027x_port_enabled(* None (inherited from caller). */ -static int pdc2027x_prereset (struct ata_port *ap) +static int pdc2027x_prereset (struct ata_link *link) {/* Check whether port enabled */ -if (!pdc2027x_port_enabled (ap)) +if (!pdc2027x_port_enabled (link->ap))return -ENOENT ; -pdc2027x_cbl_detect (ap); -return ata_std_prereset (ap); +pdc2027x_cbl_detect (link->ap); +return ata_std_prereset (link); }/**
drivers/ata/pata_pdc202xx_old.c +7 -6
@@ -25,15 +25,15 @@ #define DRV_VERSION "0.2.1"/** * pdc2024x_pre_reset - probe begin -* @ap: ATA port +* @link: ATA link * * Set up cable type and use generic probe init */ -static int pdc2024x_pre_reset (struct ata_port *ap) +static int pdc2024x_pre_reset (struct ata_link *link) { - ap->cbl =ATA_CBL_PATA40 ; -return ata_std_prereset (ap); + link->ap->cbl =ATA_CBL_PATA40 ; +return ata_std_prereset (link); }
@@ -43,8 +43,9 @@ static void pdc2024x_error_handler(struc } -static int pdc2026x_pre_reset (struct ata_port *ap) +static int pdc2026x_pre_reset (struct ata_link *link) { +struct ata_port *ap = link->ap;struct pci_dev *pdev =to_pci_dev (ap->host->dev);u16 cis;
@@ -54,7 +55,7 @@ static int pdc2026x_pre_reset(struct ataelse ap->cbl =ATA_CBL_PATA40 ; -return ata_std_prereset (ap); +return ata_std_prereset (link); }static void pdc2026x_error_handler (struct ata_port *ap)
drivers/ata/pata_radisys.c +4 -4
@@ -28,15 +28,15 @@ #define DRV_VERSION "0.4.1"/** * radisys_probe_init - probe begin -* @ap: ATA port +* @link: ATA link * * Set up cable type and use generic probe init */ -static int radisys_pre_reset (struct ata_port *ap) +static int radisys_pre_reset (struct ata_link *link) { - ap->cbl =ATA_CBL_PATA80 ; -return ata_std_prereset (ap); + link->ap->cbl =ATA_CBL_PATA80 ; +return ata_std_prereset (link); }
drivers/ata/pata_rz1000.c +4 -4
@@ -26,15 +26,15 @@ #define DRV_VERSION "0.2.2"/** * rz1000_prereset - probe begin -* @ap: ATA port +* @link: ATA link * * Set up cable type and use generics */ -static int rz1000_prereset (struct ata_port *ap) +static int rz1000_prereset (struct ata_link *link) { - ap->cbl =ATA_CBL_PATA40 ; -return ata_std_prereset (ap); + link->ap->cbl =ATA_CBL_PATA40 ; +return ata_std_prereset (link); }/**
drivers/ata/pata_serverworks.c +5 -3
@@ -138,13 +138,15 @@ static struct sv_cable_table cable_detec/** * serverworks_pre_reset - cable detection -* @ap: ATA port +* @link: ATA link * * Perform cable detection according to the device and subvendor * identifications */ -static int serverworks_pre_reset (struct ata_port *ap) { +static int serverworks_pre_reset (struct ata_link *link) +{ +struct ata_port *ap = link->ap;struct pci_dev *pdev =to_pci_dev (ap->host->dev);struct sv_cable_table *cb = cable_detect;
@@ -153,7 +155,7 @@ static int serverworks_pre_reset(struct (cb->subvendor == pdev->subsystem_vendor || cb->subvendor == PCI_ANY_ID)) { ap->cbl = cb->cable_detect (ap); -return ata_std_prereset (ap); +return ata_std_prereset (link); } cb++; }
drivers/ata/pata_sil680.c +7 -6
@@ -91,21 +91,22 @@ static int sil680_cable_detect(struct atreturn ATA_CBL_PATA40 ; } -static int sil680_pre_reset (struct ata_port *ap) +static int sil680_pre_reset (struct ata_link *link) { - ap->cbl =sil680_cable_detect (ap); -return ata_std_prereset (ap); + link->ap->cbl =sil680_cable_detect (link->ap); +return ata_std_prereset (link); }/** * sil680_bus_reset - reset the SIL680 bus -* @ap: ATA port to reset +* @link: ATA link to reset * * Perform the SIL680 housekeeping when doing an ATA bus reset */ -static int sil680_bus_reset (struct ata_port *ap,unsigned int *classes) +static int sil680_bus_reset (struct ata_link *link,unsigned int *classes) { +struct ata_port *ap = link->ap;struct pci_dev *pdev =to_pci_dev (ap->host->dev);unsigned long addr =sil680_selreg (ap,0 );u8 reset;
@@ -114,7 +115,7 @@ static int sil680_bus_reset(struct ata_ppci_write_config_byte (pdev, addr, reset |0x03 );udelay (25 );pci_write_config_byte (pdev, addr, reset); -return ata_std_softreset (ap, classes); +return ata_std_softreset (link, classes); }static void sil680_error_handler (struct ata_port *ap)
drivers/ata/pata_sis.c +12 -9
@@ -58,19 +58,20 @@ static int sis_port_base(struct ata_devi/** * sis_133_pre_reset - check for 40/80 pin -* @ap: Port +* @link: ATA link * * Perform cable detection for the later UDMA133 capable * SiS chipset. */ -static int sis_133_pre_reset (struct ata_port *ap) +static int sis_133_pre_reset (struct ata_link *link) {static const struct pci_bits sis_enable_bits[] = { {0x4aU ,1U ,0x02UL ,0x02UL },/* port 0 */ {0x4aU ,1U ,0x04UL ,0x04UL },/* port 1 */ }; +struct ata_port *ap = link->ap;struct pci_dev *pdev =to_pci_dev (ap->host->dev);u16 tmp;
@@ -84,7 +85,7 @@ static int sis_133_pre_reset(struct ata_else ap->cbl =ATA_CBL_PATA80 ; -return ata_std_prereset (ap); +return ata_std_prereset (link); }/**
@@ -103,19 +104,20 @@ static void sis_133_error_handler(struct/** * sis_66_pre_reset - check for 40/80 pin -* @ap: Port +* @link: ATA link * * Perform cable detection on the UDMA66, UDMA100 and early UDMA133 * SiS IDE controllers. */ -static int sis_66_pre_reset (struct ata_port *ap) +static int sis_66_pre_reset (struct ata_link *link) {static const struct pci_bits sis_enable_bits[] = { {0x4aU ,1U ,0x02UL ,0x02UL },/* port 0 */ {0x4aU ,1U ,0x04UL ,0x04UL },/* port 1 */ }; +struct ata_port *ap = link->ap;struct pci_dev *pdev =to_pci_dev (ap->host->dev);u8 tmp;
@@ -132,7 +134,7 @@ static int sis_66_pre_reset(struct ata_pelse ap->cbl =ATA_CBL_PATA80 ; -return ata_std_prereset (ap); +return ata_std_prereset (link); }/**
@@ -151,18 +153,19 @@ static void sis_66_error_handler(struct/** * sis_old_pre_reset - probe begin -* @ap: ATA port +* @link: ATA link * * Set up cable type and use generic probe init */ -static int sis_old_pre_reset (struct ata_port *ap) +static int sis_old_pre_reset (struct ata_link *link) {static const struct pci_bits sis_enable_bits[] = { {0x4aU ,1U ,0x02UL ,0x02UL },/* port 0 */ {0x4aU ,1U ,0x04UL ,0x04UL },/* port 1 */ }; +struct ata_port *ap = link->ap;struct pci_dev *pdev =to_pci_dev (ap->host->dev);if (!pci_test_config_bits (pdev, &sis_enable_bits[ap->port_no])) {
@@ -171,7 +174,7 @@ static int sis_old_pre_reset(struct ata_return 0 ; } ap->cbl =ATA_CBL_PATA40 ; -return ata_std_prereset (ap); +return ata_std_prereset (link); }
drivers/ata/pata_sl82c105.c +3 -2
@@ -41,18 +41,19 @@ enum {* Set up cable type and use generic probe init */ -static int sl82c105_pre_reset (struct ata_port *ap) +static int sl82c105_pre_reset (struct ata_link *link) {static const struct pci_bits sl82c105_enable_bits[] = { {0x40 ,1 ,0x01 ,0x01 }, {0x40 ,1 ,0x10 ,0x10 } }; +struct ata_port *ap = link->ap;struct pci_dev *pdev =to_pci_dev (ap->host->dev);if (ap->port_no && !pci_test_config_bits (pdev, &sl82c105_enable_bits[ap->port_no]))return -ENOENT ; ap->cbl =ATA_CBL_PATA40 ; -return ata_std_prereset (ap); +return ata_std_prereset (link); }
drivers/ata/pata_triflex.c +4 -3
@@ -47,24 +47,25 @@ #define DRV_VERSION "0.2.5"/** * triflex_prereset - probe begin -* @ap: ATA port +* @link: ATA link * * Set up cable type and use generic probe init */ -static int triflex_prereset (struct ata_port *ap) +static int triflex_prereset (struct ata_link *link) {static const struct pci_bits triflex_enable_bits[] = { {0x80 ,1 ,0x01 ,0x01 }, {0x80 ,1 ,0x02 ,0x02 } }; +struct ata_port *ap = link->ap;struct pci_dev *pdev =to_pci_dev (ap->host->dev);if (!pci_test_config_bits (pdev, &triflex_enable_bits[ap->port_no]))return -ENOENT ; ap->cbl =ATA_CBL_PATA40 ; -return ata_std_prereset (ap); +return ata_std_prereset (link); }
drivers/ata/pata_via.c +3 -2
@@ -143,8 +143,9 @@ static int via_cable_detect(struct ata_preturn ATA_CBL_PATA40 ; } -static int via_pre_reset (struct ata_port *ap) +static int via_pre_reset (struct ata_link *link) { +struct ata_port *ap = link->ap;const struct via_isa_bridge *config = ap->host->private_data;if (!(config->flags &VIA_NO_ENABLES )) {
@@ -163,7 +164,7 @@ static int via_pre_reset(struct ata_port ap->cbl =via_cable_detect (ap); else ap->cbl = ATA_CBL_PATA40; -return ata_std_prereset (ap); +return ata_std_prereset (link); }
drivers/ata/sata_nv.c +2 -2
@@ -452,7 +452,7 @@ static void nv_ck804_thaw(struct ata_porwriteb (mask, mmio_base +NV_INT_ENABLE_CK804 ); } -static int nv_hardreset (struct ata_port *ap,unsigned int *class) +static int nv_hardreset (struct ata_link *link,unsigned int *class) {unsigned int dummy;
@@ -460,7 +460,7 @@ static int nv_hardreset(struct ata_port* some controllers. Don't classify on hardreset. For more * info, see http://bugme.osdl.org/show_bug.cgi?id=3352 */ -return sata_std_hardreset (ap, &dummy); +return sata_std_hardreset (link, &dummy); }static void nv_error_handler (struct ata_port *ap)
drivers/ata/sata_sil24.c +11 -9
@@ -540,8 +540,9 @@ static int sil24_init_port(struct ata_poreturn 0 ; } -static int sil24_softreset (struct ata_port *ap,unsigned int *class) +static int sil24_softreset (struct ata_link *link,unsigned int *class) { +struct ata_port *ap = link->ap;void __iomem *port = (void __iomem *)ap->ioaddr.cmd_addr;struct sil24_port_priv *pp = ap->private_data;struct sil24_prb *prb = &pp->cmd_block[0 ].ata.prb;
@@ -551,7 +552,7 @@ static int sil24_softreset(struct ata_poDPRINTK ("ENTER\n" ); -if (ata_link_offline (&ap->link)) { +if (ata_link_offline (link)) {DPRINTK ("PHY reports no device\n" ); *class =ATA_DEV_NONE ; goto out;
@@ -596,22 +597,23 @@ static int sil24_softreset(struct ata_poreturn 0 ; err: -ata_port_printk (ap,KERN_ERR ,"softreset failed (%s)\n" , reason); +ata_link_printk (link,KERN_ERR ,"softreset failed (%s)\n" , reason);return -EIO ; } -static int sil24_hardreset (struct ata_port *ap,unsigned int *class) +static int sil24_hardreset (struct ata_link *link,unsigned int *class) { +struct ata_port *ap = link->ap;void __iomem *port = (void __iomem *)ap->ioaddr.cmd_addr;const char *reason;int tout_msec, rc;u32 tmp;/* sil24 does the right thing(tm) without any protection */ -sata_set_spd (&ap->link); +sata_set_spd (link); tout_msec =100 ; -if (ata_link_online (&ap->link)) +if (ata_link_online (link)) tout_msec =5000 ;writel (PORT_CS_DEV_RST , port +PORT_CTRL_STAT );
@@ -621,14 +623,14 @@ static int sil24_hardreset(struct ata_po/* SStatus oscillates between zero and valid status after * DEV_RST, debounce it. */ - rc =sata_link_debounce (&ap->link, sata_deb_timing_long); + rc =sata_link_debounce (link, sata_deb_timing_long);if (rc) { reason ="PHY debouncing failed" ; goto err; }if (tmp &PORT_CS_DEV_RST ) { -if (ata_link_offline (&ap->link)) +if (ata_link_offline (link))return 0 ; reason ="link not ready" ; goto err;
@@ -643,7 +645,7 @@ static int sil24_hardreset(struct ata_poreturn -EAGAIN ; err: -ata_port_printk (ap,KERN_ERR ,"hardreset failed (%s)\n" , reason); +ata_link_printk (link,KERN_ERR ,"hardreset failed (%s)\n" , reason);return -EIO ; }
drivers/ata/sata_via.c +3 -2
@@ -205,7 +205,7 @@ static void svia_scr_write (struct ata_p/** * vt6420_prereset - prereset for vt6420 -* @ap: target ATA port +* @link: target ATA link * * SCR registers on vt6420 are pieces of shit and may hang the * whole machine completely if accessed with the wrong timing.
@@ -222,8 +222,9 @@ static void svia_scr_write (struct ata_p* RETURNS: * 0 on success, -errno otherwise. */ -static int vt6420_prereset (struct ata_port *ap) +static int vt6420_prereset (struct ata_link *link) { +struct ata_port *ap = link->ap;struct ata_eh_context *ehc = &ap->link.eh_context;unsigned long timeout = jiffies + (HZ *5 );u32 sstatus, scontrol;
include/linux/libata.h +9 -8
@@ -337,13 +337,14 @@ enum ata_completion_errors {struct scsi_device ;struct ata_port_operations ;struct ata_port ; +struct ata_link ;struct ata_queued_cmd ;/* typedefs */ typedef void (*ata_qc_cb_t ) (struct ata_queued_cmd *qc); -typedef int (*ata_prereset_fn_t )(struct ata_port *ap); -typedef int (*ata_reset_fn_t )(struct ata_port *ap,unsigned int *classes); -typedef void (*ata_postreset_fn_t )(struct ata_port *ap,unsigned int *classes); +typedef int (*ata_prereset_fn_t )(struct ata_link *link); +typedef int (*ata_reset_fn_t )(struct ata_link *link,unsigned int *classes); +typedef void (*ata_postreset_fn_t )(struct ata_link *link,unsigned int *classes);struct ata_ioports {unsigned long cmd_addr;
@@ -714,12 +715,12 @@ extern int sata_set_spd(struct ata_linkextern int sata_link_debounce (struct ata_link *link,const unsigned long *params);extern int sata_link_resume (struct ata_link *link,const unsigned long *params); -extern int ata_std_prereset (struct ata_port *ap); -extern int ata_std_softreset (struct ata_port *ap,unsigned int *classes); -extern int sata_port_hardreset (struct ata_port *ap, +extern int ata_std_prereset (struct ata_link *link); +extern int ata_std_softreset (struct ata_link *link,unsigned int *classes); +extern int sata_link_hardreset (struct ata_link *link,const unsigned long *timing); -extern int sata_std_hardreset (struct ata_port *ap,unsigned int *class); -extern void ata_std_postreset (struct ata_port *ap,unsigned int *classes); +extern int sata_std_hardreset (struct ata_link *link,unsigned int *class); +extern void ata_std_postreset (struct ata_link *link,unsigned int *classes);extern void sata_std_hp_poll_activate (struct ata_port *ap);extern int sata_std_hp_poll (struct ata_port *ap);extern int ata_dev_revalidate (struct ata_device *dev,int post_reset);
Signature · 1 line
1.4.2.3
PATCH 9/18 libata-link: linkify config/EH related functions
In reply to Tejun HeoMake the following functions deal with ata_link instead of ata_port.
* ata_set_mode()
* ata_eh_autopsy() and related functions
* ata_eh_report() and related functions
* suspend/resume related functions
* ata_eh_recover() and related functions
--- drivers/ata/libata-core.c | 8 +- drivers/ata/libata-eh.c | 163 ++++++++++++++++++++++++--------------------- drivers/ata/libata.h | 3 + 3 files changed, 92 insertions(+), 82 deletions(-)
drivers/ata/libata-core.c +4 -4
@@ -1638,7 +1638,7 @@ int ata_bus_probe(struct ata_port *ap) }/* configure transfer mode */ - rc =ata_set_mode (ap, &dev); + rc =ata_set_mode (&ap->link, &dev);if (rc) { down_xfermask =1 ; goto fail;
@@ -2180,7 +2180,7 @@ static int ata_dev_set_mode(struct ata_d/** * ata_set_mode - Program timings and issue SET FEATURES - XFER -* @ap: port on which timings will be programmed +* @link: link on which timings will be programmed * @r_failed_dev: out paramter for failed device * * Set ATA device disk transfer mode (PIO3, UDMA6, etc.). If
@@ -2193,9 +2193,9 @@ static int ata_dev_set_mode(struct ata_d* RETURNS: * 0 on success, negative errno otherwise */ -int ata_set_mode (struct ata_port *ap,struct ata_device **r_failed_dev) +int ata_set_mode (struct ata_link *link,struct ata_device **r_failed_dev) { -struct ata_link *link = &ap->link; +struct ata_port *ap = link->ap;struct ata_device *dev;int rc =0 , used_dma =0 , found =0 ;
drivers/ata/libata-eh.c +86 -77
499 lines not on this page · raw message
drivers/ata/libata.h +2 -1
@@ -57,7 +57,8 @@ extern int ata_dev_configure(struct ata_extern int sata_down_spd_limit (struct ata_link *link);extern int sata_set_spd_needed (struct ata_link *link);extern int ata_down_xfermask_limit (struct ata_device *dev,int force_pio0); -extern int ata_set_mode (struct ata_port *ap,struct ata_device **r_failed_dev); +extern int ata_set_mode (struct ata_link *link, +struct ata_device **r_failed_dev);extern void ata_qc_free (struct ata_queued_cmd *qc);extern void ata_qc_issue (struct ata_queued_cmd *qc);extern void __ata_qc_complete (struct ata_queued_cmd *qc);
Signature · 1 line
1.4.2.3
PATCH 10/18 libata-link: separate out link initialization functions
In reply to Tejun HeoSeparate out link initialization into ata_link_init() and ata_link_init_sata_spd_limit().
--- drivers/ata/libata-core.c | 80 +++++++++++++++++++++++++++++++++++---------- 1 files changed, 62 insertions(+), 18 deletions(-)
drivers/ata/libata-core.c +62 -18
@@ -5392,6 +5392,66 @@ void ata_dev_init(struct ata_device *dev }/** +* ata_link_init - Initialize an ata_link structure +* @ap: ATA port link is attached to +* @link: Link structure to initialize +* +* Initialize @link. +* +* LOCKING: +* Kernel thread context (may sleep) +*/ +static void ata_link_init (struct ata_port *ap,struct ata_link *link) +{ +struct ata_device *dev; + +/* clear everything except for devices */ + memset(link, 0, offsetof(struct ata_link, device[0])); + + link->ap = ap; + link->active_tag =ATA_TAG_POISON ; + link->hw_sata_spd_limit =UINT_MAX ; + +ata_link_for_each_dev (dev, link) { + dev->link = link; + dev->devno = dev - link->device; +ata_dev_init (dev); + } +} + +/** +* sata_link_init_spd_limit - Initialize link->sata_spd_limit +* @link: Link to configure sata_spd_limit for +* +* Initialize @link->[hw_]sata_spd_limit to the currently +* configured value. +* +* LOCKING: +* Kernel thread context (may sleep). +* +* RETURNS: +* 0 on success, -errno on failure. +*/ +static int sata_link_init_spd_limit (struct ata_link *link) +{ + +u32 scontrol, spd; +int rc; + + rc =sata_scr_read (link,SCR_CONTROL , &scontrol); +if (rc) +return rc; + + spd = (scontrol >>4 ) &0xf ; +if (spd) + link->hw_sata_spd_limit &= (1 << spd) -1 ; + + link->sata_spd_limit = link->hw_sata_spd_limit; + +return 0 ; +} + +/** * ata_port_init - Initialize an ata_port structure * @ap: Structure to initialize * @host: Collection of hosts to which @ap belongs
@@ -5406,8 +5466,6 @@ void ata_dev_init(struct ata_device *devvoid ata_port_init (struct ata_port *ap,struct ata_host *host,const struct ata_probe_ent *ent,unsigned int port_no) { -unsigned int i; - ap->lock = &host->lock; ap->flags =ATA_FLAG_DISABLED ; ap->id = ata_unique_id++;
@@ -5428,8 +5486,6 @@ void ata_port_init(struct ata_port *ap, ap->flags |= ent->port_flags; ap->ops = ent->port_ops; } - ap->link.hw_sata_spd_limit =UINT_MAX ; - ap->link.active_tag =ATA_TAG_POISON ; ap->last_ctl =0xFF ;#if defined(ATA_VERBOSE_DEBUG )
@@ -5452,14 +5508,7 @@ #endifif (ap->flags &ATA_FLAG_SATA ) ap->cbl =ATA_CBL_SATA ; - ap->link.ap = ap; - -for (i =0 ; i <ata_link_max_devices (&ap->link); i++) { -struct ata_device *dev = &ap->link.device[i]; - dev->link = &ap->link; - dev->devno = i; -ata_dev_init (dev); - } +ata_link_init (ap, &ap->link);#ifdef ATA_IRQ_TRAP ap->stats.unhandled_irq =1 ;
@@ -5677,15 +5726,10 @@ int ata_device_add(const struct ata_probDPRINTK ("probe begin\n" );for (i =0 ; i < host->n_ports; i++) {struct ata_port *ap = host->ports[i]; -u32 scontrol;int rc;/* init sata_spd_limit to the current value */ -if (sata_scr_read (&ap->link,SCR_CONTROL , &scontrol) ==0 ) { -int spd = (scontrol >>4 ) &0xf ; - ap->link.hw_sata_spd_limit &= (1 << spd) -1 ; - } - ap->link.sata_spd_limit = ap->link.hw_sata_spd_limit; +sata_link_init_spd_limit (&ap->link); rc =scsi_add_host (ap->scsi_host, dev);if (rc) {
Signature · 1 line
1.4.2.3
Re: [PATCH 10/18] [PATCH] libata-link: separate out link initialization functions
Quoted 2 lines · Tejun Heo
Separate out link initialization into
ata_link_init()andata_link_init_sata_spd_limit().
pushing the bounds of good taste, with a long function name :)
PATCH 11/18 libata-link: implement link->reset_tries
In reply to Tejun HeoMake reset_tries per-link property. PMP links will use different value from host links.
--- drivers/ata/libata-core.c | 1 + drivers/ata/libata-eh.c | 2 +- include/linux/libata.h | 2 ++ 3 files changed, 4 insertions(+), 1 deletions(-)
drivers/ata/libata-core.c +1 -0
@@ -5411,6 +5411,7 @@ static void ata_link_init(struct ata_por link->ap = ap; link->active_tag =ATA_TAG_POISON ; link->hw_sata_spd_limit =UINT_MAX ; + link->reset_tries =ATA_EH_RESET_TRIES ;ata_link_for_each_dev (dev, link) { dev->link = link;
drivers/ata/libata-eh.c +1 -1
@@ -1522,7 +1522,7 @@ static int ata_eh_reset(struct ata_link {struct ata_eh_context *ehc = &link->eh_context;unsigned int *classes = ehc->classes; -int tries =ATA_EH_RESET_TRIES ; +int tries = link->reset_tries;int verbose = !(ehc->i.flags &ATA_EHI_QUIET );struct ata_device *dev;unsigned int action;
include/linux/libata.h +2 -0
@@ -537,6 +537,8 @@ struct ata_link {unsigned int hw_sata_spd_limit;unsigned int sata_spd_limit; +int reset_tries; +/* record runtime error info, protected by host_set lock */ struct ata_eh_info eh_info;/* EH context */
Signature · 1 line
1.4.2.3
PATCH 12/18 libata-link: implement ata_link_abort()
In reply to Tejun HeoImplement ata_link_abort().
--- drivers/ata/libata-core.c | 1 + drivers/ata/libata-eh.c | 50 ++++++++++++++++++++++++++++++++------------- include/linux/libata.h | 1 + 3 files changed, 38 insertions(+), 14 deletions(-)
drivers/ata/libata-core.c +1 -0
@@ -6349,6 +6349,7 @@ EXPORT_SYMBOL_GPL(ata_scsi_device_resumeEXPORT_SYMBOL_GPL (ata_eng_timeout);EXPORT_SYMBOL_GPL (ata_port_schedule_eh); +EXPORT_SYMBOL_GPL (ata_link_abort);EXPORT_SYMBOL_GPL (ata_port_abort);EXPORT_SYMBOL_GPL (ata_port_freeze);EXPORT_SYMBOL_GPL (ata_eh_freeze_port);
drivers/ata/libata-eh.c +36 -14
68 lines not on this page · raw message
include/linux/libata.h +1 -0
@@ -890,6 +890,7 @@ #endif /* CONFIG_PCI */extern void ata_eng_timeout (struct ata_port *ap);extern void ata_port_schedule_eh (struct ata_port *ap); +extern int ata_link_abort (struct ata_link *link);extern int ata_port_abort (struct ata_port *ap);extern int ata_port_freeze (struct ata_port *ap);
Signature · 1 line
1.4.2.3
PATCH 13/18 libata-link: add PMP links
In reply to Tejun HeoAdd link->pmp, ap->nr_pmp_links, ap->pmp_link[], and implement/update link helpers.
printk helpers are updated such that port and link are identifed as 'ataP:' if no PMP is attached, while device is identified as 'ataP.DD:'. If PMP is attached, they become 'ataP:', 'ataP.LL:' and 'ataP.LL' - ie. link and device are identified their PMP number.
If PPM is attached (ap->nr_pmp_links != 0), ata_for_each_link() iterates over PMP links, while __ata_for_each_link() iterates over the host link + PMP links. If PMP is not attached (ap->nr_pmp_links == 0), both iterate over only the host link.
--- drivers/ata/libata-core.c | 6 +++-- include/linux/libata.h | 52 ++++++++++++++++++++++++++++++++++++++++----- 2 files changed, 50 insertions(+), 8 deletions(-)
drivers/ata/libata-core.c +4 -2
@@ -5395,13 +5395,14 @@ void ata_dev_init(struct ata_device *dev* ata_link_init - Initialize an ata_link structure * @ap: ATA port link is attached to * @link: Link structure to initialize +* @pmp: Port multiplier port number * * Initialize @link. * * LOCKING: * Kernel thread context (may sleep) */ -static void ata_link_init (struct ata_port *ap,struct ata_link *link) +static void ata_link_init (struct ata_port *ap,struct ata_link *link,int pmp) {struct ata_device *dev;
@@ -5409,6 +5410,7 @@ static void ata_link_init(struct ata_por memset(link, 0, offsetof(struct ata_link, device[0])); link->ap = ap; + link->pmp = pmp; link->active_tag =ATA_TAG_POISON ; link->hw_sata_spd_limit =UINT_MAX ; link->reset_tries =ATA_EH_RESET_TRIES ;
@@ -5509,7 +5511,7 @@ #endifif (ap->flags &ATA_FLAG_SATA ) ap->cbl =ATA_CBL_SATA ; -ata_link_init (ap, &ap->link); +ata_link_init (ap, &ap->link,0 );#ifdef ATA_IRQ_TRAP ap->stats.unhandled_irq =1 ;
include/linux/libata.h +46 -6
84 lines not on this page · raw message
Signature · 1 line
1.4.2.3
PATCH 14/18 libata-link: update ata_scsi_error() to handle PMP links
In reply to Tejun HeoUpdate ata_scsi_error() to handle PMP links. As error conditions can occur on both host and PMP links, __ata_port_for_each_link() is used.
--- drivers/ata/libata-eh.c | 13 +++++++++---- 1 files changed, 9 insertions(+), 4 deletions(-)
drivers/ata/libata-eh.c +9 -4
@@ -272,15 +272,19 @@ void ata_scsi_error(struct Scsi_Host *ho repeat:/* invoke error handler */ if (ap->ops->error_handler) { +struct ata_link *link; +/* process port resume request */ ata_eh_handle_port_resume (ap);/* fetch & clear EH info */ spin_lock_irqsave (ap->lock, flags); -memset (&ap->link.eh_context,0 ,sizeof (ap->link.eh_context)); - ap->link.eh_context.i = ap->link.eh_info; -memset (&ap->link.eh_info,0 ,sizeof (ap->link.eh_info)); +__ata_port_for_each_link (link, ap) { +memset (&link->eh_context,0 ,sizeof (link->eh_context)); + link->eh_context.i = link->eh_info; +memset (&link->eh_info,0 ,sizeof (link->eh_info)); + } ap->pflags |=ATA_PFLAG_EH_IN_PROGRESS ; ap->pflags &= ~ATA_PFLAG_EH_PENDING ;
@@ -315,7 +319,8 @@ void ata_scsi_error(struct Scsi_Host *ho }/* this run is complete, make sure EH info is clear */ -memset (&ap->link.eh_info,0 ,sizeof (ap->link.eh_info)); +__ata_port_for_each_link (link, ap) +memset (&link->eh_info,0 ,sizeof (link->eh_info));/* Clear host_eh_scheduled while holding ap->lock such * that if exception occurs after this point but
Signature · 1 line
1.4.2.3
PATCH 15/18 libata-link: update ata_dev_configure() to deal with PMP links
In reply to Tejun HeoUpdate ata_dev_configure() to deal with PMP links.
--- drivers/ata/libata-core.c | 9 ++++++--- 1 files changed, 6 insertions(+), 3 deletions(-)
drivers/ata/libata-core.c +6 -3
@@ -1363,10 +1363,13 @@ static void ata_set_port_max_cmd_len(str {if (ap->scsi_host) {unsigned int len =0 ; -struct ata_device *dev; +struct ata_link *link; -ata_link_for_each_dev (dev, &ap->link) - len =max (len, dev->cdb_len); +ata_port_for_each_link (link, ap) { +struct ata_device *dev; +ata_link_for_each_dev (dev, link) + len =max (len, dev->cdb_len); + } ap->scsi_host->max_cmd_len = len; }
Signature · 1 line
1.4.2.3
PATCH 16/18 libata-link: update EH to deal with PMP links
In reply to Tejun HeoUpdate ata_eh_autopsy(), ata_eh_report() and ata_eh_recover() to deal with PMP links. ata_eh_autopsy() and ata_eh_report() updates are straightforward. They just repeat the same operation over all configured links.
ata_eh_recover() update is more complex as it first processes all resets and then performs the rest. This is necessary as thawing with some links in unknown state can be dangerous. ehi->action is cleared on successful recovery of a link to avoid repeating recovery due to failures in other links.
ata_eh_recover() iterates over only PMP links if PMP is attached, and, on failure, the failing link is returned in @failed_link instead of disabling devices directly. These are to integrate ata_eh_recover() into PMP EH later.
--- drivers/ata/libata-eh.c | 248 ++++++++++++++++++++++++++++++++--------------- 1 files changed, 170 insertions(+), 78 deletions(-)
drivers/ata/libata-eh.c +170 -78
@@ -1332,8 +1332,8 @@ static int ata_eh_speed_down(struct ata_ }/** -* ata_eh_autopsy - analyze error and determine recovery action -* @link: ATA link to perform autopsy on +* ata_eh_link_autopsy - analyze error and determine recovery action +* @link: host link to perform autopsy on * * Analyze why @link failed and determine which recovery actions * are needed. This function also sets more detailed AC_ERR_*
@@ -1342,7 +1342,7 @@ static int ata_eh_speed_down(struct ata_* LOCKING: * Kernel thread context (may sleep). */ -static void ata_eh_autopsy (struct ata_link *link) +static void ata_eh_link_autopsy (struct ata_link *link) {struct ata_port *ap = link->ap;struct ata_eh_context *ehc = &link->eh_context;
@@ -1432,7 +1432,25 @@ static void ata_eh_autopsy(struct ata_li }/** -* ata_eh_report - report error handling to user +* ata_eh_autopsy - analyze error and determine recovery action +* @ap: host port to perform autopsy on +* +* Analyze all links of @ap and determine why they failed and +* which recovery actions are needed. +* +* LOCKING: +* Kernel thread context (may sleep). +*/ +static void ata_eh_autopsy (struct ata_port *ap) +{ +struct ata_link *link; + +__ata_port_for_each_link (link, ap) +ata_eh_link_autopsy (link); +} + +/** +* ata_eh_link_report - report error handling to user * @link: ATA link EH is going on * * Report EH to user.
@@ -1440,7 +1458,7 @@ static void ata_eh_autopsy(struct ata_li* LOCKING: * None. */ -static void ata_eh_report (struct ata_link *link) +static void ata_eh_link_report (struct ata_link *link) {struct ata_port *ap = link->ap;struct ata_eh_context *ehc = &link->eh_context;
@@ -1500,6 +1518,23 @@ static void ata_eh_report(struct ata_lin } } +/** +* ata_eh_report - report error handling to user +* @ap: ATA port to report EH about +* +* Report EH to user. +* +* LOCKING: +* None. +*/ +static void ata_eh_report (struct ata_port *ap) +{ +struct ata_link *link; + +__ata_port_for_each_link (link, ap) +ata_eh_link_report (link); +} +static int ata_do_reset (struct ata_link *link,ata_reset_fn_t reset,unsigned int *classes) {
@@ -1904,6 +1939,17 @@ static int ata_link_nr_enabled(struct atreturn cnt; } +static int ata_port_nr_enabled (struct ata_port *ap) +{ +struct ata_link *link; +int cnt =0 ; + +ata_port_for_each_link (link, ap) + cnt +=ata_link_nr_enabled (link); + +return cnt; +} +static int ata_link_nr_vacant (struct ata_link *link) {struct ata_device *dev;
@@ -2000,12 +2046,13 @@ static void ata_eh_handle_dev_fail(struc* @softreset: softreset method (can be NULL) * @hardreset: hardreset method (can be NULL) * @postreset: postreset method (can be NULL) +* @r_failed_link: out parameter for failed link * * This is the alpha and omega, eum and yang, heart and soul of * libata exception handling. On entry, actions required to -* recover the port and hotplug requests are recorded in -* eh_context. This function executes all the operations with -* appropriate retrials and fallbacks to resurrect failed +* recover each link and hotplug requests are recorded in the +* link's eh_context. This function executes all the operations +* with appropriate retrials and fallbacks to resurrect failed * devices, detach goners and greet newcomers. * * LOCKING:
@@ -2016,115 +2063,147 @@ static void ata_eh_handle_dev_fail(struc*/ static int ata_eh_recover (struct ata_port *ap,ata_prereset_fn_t prereset,ata_reset_fn_t softreset,ata_reset_fn_t hardreset, -ata_postreset_fn_t postreset) +ata_postreset_fn_t postreset, +struct ata_link **r_failed_link) { -struct ata_link *link = &ap->link; -struct ata_eh_context *ehc = &link->eh_context; +struct ata_link *link;struct ata_device *dev; -int down_xfermask, rc; +int nr_failed_devs; +int reset, rc;DPRINTK ("ENTER\n" );/* prep for recovery */ -ata_link_for_each_dev (dev, link) { - ehc->tries[dev->devno] =ATA_EH_DEV_TRIES ; +ata_port_for_each_link (link, ap) { +struct ata_eh_context *ehc = &link->eh_context; -/* process hotplug request */ -if (dev->flags &ATA_DFLAG_DETACH ) -ata_eh_detach_dev (dev); +ata_link_for_each_dev (dev, link) { + ehc->tries[dev->devno] =ATA_EH_DEV_TRIES ; -if (!ata_dev_enabled (dev) && - ((ehc->i.probe_mask & (1 << dev->devno)) && - !(ehc->did_probe_mask & (1 << dev->devno)))) { -ata_eh_detach_dev (dev); -ata_dev_init (dev); - ehc->did_probe_mask |= (1 << dev->devno); - ehc->i.action |=ATA_EH_SOFTRESET ; +/* process hotplug request */ +if (dev->flags &ATA_DFLAG_DETACH ) +ata_eh_detach_dev (dev); + +if (!ata_dev_enabled (dev) && + (ehc->i.probe_mask & (1 << dev->devno) && + !(ehc->did_probe_mask & (1 << dev->devno)))) { +ata_eh_detach_dev (dev); +ata_dev_init (dev); + ehc->did_probe_mask |= (1 << dev->devno); + ehc->i.action |=ATA_EH_SOFTRESET ; + } } } retry: - down_xfermask =0 ; rc =0 ; + nr_failed_devs =0 ; + reset =0 ;/* if UNLOADING, finish immediately */ if (ap->pflags &ATA_PFLAG_UNLOADING ) goto out; -/* prep for resume */ -ata_eh_prep_resume (link); +/* prep for EH */ +ata_port_for_each_link (link, ap) { +struct ata_eh_context *ehc = &link->eh_context; -/* skip EH if possible. */ -if (ata_eh_skip_recovery (link)) - ehc->i.action =0 ; +/* prep for resume */ +ata_eh_prep_resume (link); -ata_link_for_each_dev (dev, link) - ehc->classes[dev->devno] =ATA_DEV_UNKNOWN ; +/* skip EH if possible. */ +if (ata_eh_skip_recovery (link)) + ehc->i.action =0 ; + +/* do we need to reset? */ +if (ehc->i.action &ATA_EH_RESET_MASK ) + reset =1 ; + +ata_link_for_each_dev (dev, link) + ehc->classes[dev->devno] =ATA_DEV_UNKNOWN ; + }/* reset */ -if (ehc->i.action &ATA_EH_RESET_MASK ) { +if (reset) {ata_eh_freeze_port (ap); - rc =ata_eh_reset (link,ata_link_nr_vacant (link), prereset, - softreset, hardreset, postreset); -if (rc) { -ata_link_printk (link,KERN_ERR , -"reset failed, giving up\n" ); - goto out; +ata_port_for_each_link (link, ap) { +struct ata_eh_context *ehc = &link->eh_context; + +if (!(ehc->i.action &ATA_EH_RESET_MASK )) +continue ; + + rc =ata_eh_reset (link,ata_link_nr_vacant (link), + prereset, softreset, hardreset, + postreset); +if (rc) { +ata_link_printk (link,KERN_ERR , +"reset failed, giving up\n" ); + goto out; + } }ata_eh_thaw_port (ap); } -/* revalidate existing devices and attach new ones */ - rc =ata_eh_revalidate_and_attach (link, &dev); -if (rc) - goto dev_fail; +/* the rest */ +ata_port_for_each_link (link, ap) { +struct ata_eh_context *ehc = &link->eh_context; +int down_xfermask =0 ; -/* resume devices */ - rc =ata_eh_resume (link, &dev); -if (rc) - goto dev_fail; +/* revalidate existing devices and attach new ones */ + rc =ata_eh_revalidate_and_attach (link, &dev); +if (rc) + goto dev_fail; -/* configure transfer mode if the port has been reset */ -if (ehc->i.flags &ATA_EHI_DID_RESET ) { - rc =ata_set_mode (link, &dev); -if (rc) { - down_xfermask =1 ; +/* resume devices */ + rc =ata_eh_resume (link, &dev); +if (rc) goto dev_fail; + +/* configure transfer mode if the port has been reset */ +if (ehc->i.flags &ATA_EHI_DID_RESET ) { + rc =ata_set_mode (link, &dev); +if (rc) { + down_xfermask =1 ; + goto dev_fail; + } } - } -/* suspend devices */ - rc =ata_eh_suspend (link, &dev); -if (rc) - goto dev_fail; +/* suspend devices */ + rc =ata_eh_suspend (link, &dev); +if (rc) + goto dev_fail; - goto out; +/* this link is okay now */ + ehc->i.flags =0 ; +continue ; - dev_fail: -ata_eh_handle_dev_fail (dev, rc, down_xfermask); + dev_fail: +ata_eh_handle_dev_fail (dev, rc, down_xfermask); + nr_failed_devs++; -if (ata_link_nr_enabled (link)) { -ata_link_printk (link,KERN_WARNING ,"failed to recover some " -"devices, retrying in 5 secs\n" ); -ssleep (5 ); - }else { -/* no device left, repeat fast */ -msleep (500 ); +if (ap->pflags &ATA_PFLAG_FROZEN ) +break ; } - goto retry; - - out: -if (rc) { -/* recovery failed, activate hp-poll */ -ata_hp_poll_activate (ap); +if (nr_failed_devs) { +if (ata_port_nr_enabled (ap)) { +ata_port_printk (ap,KERN_WARNING ,"failed to recover " +"some devices, retrying in 5 secs\n" ); +ssleep (5 ); + }else { +/* no device left, repeat fast */ +msleep (500 ); + } -ata_link_for_each_dev (dev, link); -ata_dev_disable (dev); + goto retry; } + out: +if (rc && r_failed_link) + *r_failed_link = link; +DPRINTK ("EXIT, rc=%d\n" , rc);return rc; }
@@ -2188,9 +2267,22 @@ void ata_do_eh(struct ata_port *ap, ata_ ata_reset_fn_t softreset, ata_reset_fn_t hardreset, ata_postreset_fn_t postreset) { - ata_eh_autopsy(&ap->link); -ata_eh_report (&ap->link); -ata_eh_recover (ap, prereset, softreset, hardreset, postreset); + struct ata_device *dev; +int rc; + +ata_eh_autopsy (ap); +ata_eh_report (ap); + + rc =ata_eh_recover (ap, prereset, softreset, hardreset, postreset, +NULL ); +if (rc) { +/* recovery failed, activate hp-poll */ +ata_hp_poll_activate (ap); + +ata_link_for_each_dev (dev, &ap->link) +ata_dev_disable (dev); + } +ata_eh_finish (ap); }
Signature · 1 line
1.4.2.3
PATCH 17/18 libata-link: update hotplug to handle PMP links
In reply to Tejun HeoUpdate hotplug to handle PMP links. When PMP is attached, the PMP number corresponds to I of SCSI C:H:I:L.
--- drivers/ata/libata-core.c | 7 ++- drivers/ata/libata-scsi.c | 110 ++++++++++++++++++++++++++++++++------------- 2 files changed, 82 insertions(+), 35 deletions(-)
drivers/ata/libata-core.c +5 -2
@@ -5827,6 +5827,7 @@ err_out:void ata_port_detach (struct ata_port *ap) {unsigned long flags; +struct ata_link *link;struct ata_device *dev;if (!ap->ops->error_handler)
@@ -5844,8 +5845,10 @@ void ata_port_detach(struct ata_port *ap*/ spin_lock_irqsave (ap->lock, flags); -ata_link_for_each_dev (dev, &ap->link) -ata_dev_disable (dev); +ata_port_for_each_link (link, ap) { +ata_link_for_each_dev (dev, link) +ata_dev_disable (dev); + }spin_unlock_irqrestore (ap->lock, flags);
drivers/ata/libata-scsi.c +77 -33
180 lines not on this page · raw message
Signature · 1 line
1.4.2.3
PATCH 18/18 libata-link: update Power Management to handle PMP links
In reply to Tejun HeoUpdate Power Management to consider PMP links.
--- drivers/ata/libata-core.c | 20 +++++++++++++------- drivers/ata/libata-eh.c | 16 ++++++++++------ 2 files changed, 23 insertions(+), 13 deletions(-)
drivers/ata/libata-core.c +13 -7
@@ -5195,6 +5195,7 @@ static int ata_host_request_pm(struct atfor (i =0 ; i < host->n_ports; i++) {struct ata_port *ap = host->ports[i]; +struct ata_link *link;/* Previous resume operation might still be in * progress. Wait for PM_PENDING to clear.
@@ -5214,8 +5215,10 @@ static int ata_host_request_pm(struct at } ap->pflags |=ATA_PFLAG_PM_PENDING ; - ap->link.eh_info.action |= action; - ap->link.eh_info.flags |= ehi_flags; +__ata_port_for_each_link (link, ap) { + link->eh_info.action |= action; + link->eh_info.flags |= ehi_flags; + }ata_port_schedule_eh (ap);
@@ -5262,15 +5265,18 @@ int ata_host_suspend(struct ata_host *ho*/ for (i =0 ; i < host->n_ports; i++) {struct ata_port *ap = host->ports[i]; +struct ata_link *link;struct ata_device *dev; -ata_link_for_each_dev (dev, &ap->link) { -if (ata_dev_ready (dev)) { -ata_port_printk (ap,KERN_WARNING , +ata_port_for_each_link (link, ap) { +ata_link_for_each_dev (dev, link) { +if (ata_dev_ready (dev)) { +ata_port_printk (ap,KERN_WARNING ,"suspend failed, device %d " "still active\n" , dev->devno); - rc = -EBUSY ; - goto fail; + rc = -EBUSY ; + goto fail; + } } } }
drivers/ata/libata-eh.c +10 -6
@@ -2378,17 +2378,21 @@ static void ata_eh_handle_port_resume(st/* give devices time to request EH */ timeout = jiffies +HZ ;/* 1s max */ while (1 ) { +struct ata_link *link;struct ata_device *dev; -ata_link_for_each_dev (dev, &ap->link) { -unsigned int action =ata_eh_dev_action (dev); +ata_port_for_each_link (link, ap) { +ata_link_for_each_dev (dev, link) { +unsigned int action =ata_eh_dev_action (dev); -if ((dev->flags &ATA_DFLAG_SUSPENDED ) && - !(action &ATA_EH_RESUME )) -break ; +if ((dev->flags &ATA_DFLAG_SUSPENDED ) && + !(action &ATA_EH_RESUME )) + goto out_of_loop; + } } + out_of_loop: -if (dev ==NULL ||time_after (jiffies, timeout)) +if (link ==NULL ||time_after (jiffies, timeout))break ;msleep (10 ); }
Signature · 1 line
1.4.2.3
Quoted 26 lines · Tejun Heo
Hello, all.
This is the third take of implement
ata_linkpatchset. This patchset contains 18 patches which can be categorized as follows.#01-03: prep
#04-05: implementata_link
#06-09: make libata deal with link instead of port #10-12: misc link stuff (link init,reset_tries,ata_link_abort()) #13-19: add ap->pmp_link[] and update libata to deal with multiple
links
ata_linkabstracts PHY and sits betweenata_portandata_device. The following attributes are moved toata_linkfromata_port.- active command state (
active_tag, sactive)
- [hw_]sata_spd_limit
-eh_infoandeh_context
- device arrayWith above and a few extra fields, a link can fully host attached devices including qc management and EH/hotplug. This patchset makes libata ready to handle PM links.
Changes from the last take[L] are.
Quoted 8 lines
* updated to fit new #upstream
*__dev1trick removedThis patchset is against
upstream (
da54f5fe54c7d75e2db7d17961fb36a8c28a8501)
+ [1] hp-poll patchset, take #5
+ [2] vt8251-ahci patchset, take #2
Forgot about git tree, sorry. This patchset can be accessed via the following git tree.
http://htj.dyndns.org/git/?p=libata-tj.git;a=shortlog;h=link
git://htj.dyndns.org/libata-tj link
Signature · 1 line
tejun
Quoted 26 lines · Tejun Heo
Hello, all.
This is the third take of implement
ata_linkpatchset. This patchset contains 18 patches which can be categorized as follows.#01-03: prep
#04-05: implementata_link
#06-09: make libata deal with link instead of port #10-12: misc link stuff (link init,reset_tries,ata_link_abort()) #13-19: add ap->pmp_link[] and update libata to deal with multiple
links
ata_linkabstracts PHY and sits betweenata_portandata_device. The following attributes are moved toata_linkfromata_port.- active command state (
active_tag, sactive)
- [hw_]sata_spd_limit
-eh_infoandeh_context
- device arrayWith above and a few extra fields, a link can fully host attached devices including qc management and EH/hotplug. This patchset makes libata ready to handle PM links.
Changes from the last take[L] are.
Quoted 8 lines
* updated to fit new #upstream
*__dev1trick removedThis patchset is against
upstream (
da54f5fe54c7d75e2db7d17961fb36a8c28a8501)
+ [1] hp-poll patchset, take #5
+ [2] vt8251-ahci patchset, take #2
ACK patchset