Skip to contentSkip to conversation

: Add mpc7448hpc2 ( [...]

PATCH New DENX Support System 1 participant 1 message Nov 2, 2006

lore
Share & tools
lore
#0 lore raw

v3 cover : Add mpc7448hpc2 ( [...]

Hello list,

inside the automatic U-Boot patch tracking system a new ticket [DNX#2006110242000029] was created:

<snip>

Quoted 90 lines

This serial of patches have been submitted on 11, Aug., 2006. I wait for more than two months. there is no feedback, positive or negative.

I updated the patches based on the current u-boot git tree. I hope I will not wait for so long time again.
Any feedback is welcomed. I'd like to refine the code according to your warm comments.

This series of patches add mpc7448hpc2 board support. Mpc7448hpc2 (taiga) board is a high-performance PowerPC server reference design,which is optimized for high speed throughput between the processor and the memory, disk drive and Ethernet port subsystems.

The board is designed to the micro-ATX chassis, allowing it to be used in 1U or 2U rack-mount chassis

----------------------------------------------------------------------

Add README file for mpc7448hpc2 board.

---
 doc/README.mpc7448hpc2 |  193
++++++++++++++++++++++++++++++++++++++++++++++++
 1 files changed, 193 insertions(+), 0 deletions(-)
doc/README.mpc7448hpc2 new file +6 -0
new file mode 100644
index 0000000..5142a0f
@@ -0,0 +1,193 @@
+Freescale MPC7448hpc2 (Taiga) board
+===================================
+
+Created 08/11/2006 Roy Zang
+--------------------------
+MPC7448hpc2 (Taiga) board is a high-performance PowerPC server

reference
+design, which is optimized for high speed throughput between the processor and

doc/README.mpc7448hpc2 new file +3 -0
+the memory, disk drive and Ethernet port subsystems.
+
+MPC7448hpc2(Taiga) is designed to the micro-ATX chassis, allowing it to

be

doc/README.mpc7448hpc2 new file +44 -0
+used in 1U or 2U rack-mount chassisol and CPU Reset Option
+
+      7		
+      -
+  SW2=0	   	System bus uses MPX bus protocol
+  SW2=1		System bus uses 60x bus protocol
+
+      8		
+      -
+  SW2=0	   	TSI108 can cause CPU reset
+  SW2=1		TSI108 can not cause CPU reset
+
+
+SW3[1-8] system options
+
+      123		
+      ---
+  SW3=xxx	   	Connected to GPIO[0:2] on TSI108
+
+      4		
+      -
+  SW3=0	   	CPU boots from low half of flash
+  SW3=1		CPU boots from high half of flash
+
+      5		
+      -
+  SW3=0	   	SATA and slot2 connected to PCI bus
+  SW3=1		Only slot1 connected to PCI bus
+
+      6		
+      -
+  SW3=0	   	USB connected to PCI bus
+  SW3=1		USB disconnected from PCI bus
+
+      7		
+      -
+  SW3=0	   	Flash is write protected
+  SW3=1		Flash is NOT write protected
+
+      8		
+      -
+  SW3=0	   	CPU will boot from flash
+  SW3=1		CPU will boot from PromJet
+

doc/README.mpc7448hpc2

Quoted 10 lines
doc/README.mpc7448hpc2 new file +10 -0
+SW4[1-3]: System bus frequency
+
+			Bus Frequency (MHz)
+      ---
+  SW4=010			183
+  SW4=011			100
+  SW4=100			133
+  SW4=101			166 only for MPC7447A
+  SW4=110			200 only for MPC7448
+  others			reserved

</snip>

Your U-Boot support team