Skip to contentSkip to conversation

: tsi108 i2c suppo [...]

PATCH New DENX Support System 1 participant 1 message Nov 2, 2006

lore
Share & tools
lore
#0 lore raw

PATCH v3 9/10 : tsi108 i2c suppo [...]

Hello list,

inside the automatic U-Boot patch tracking system a new ticket [DNX#2006110242000118] was created:

<snip>

Quoted 90 lines

Tsi108 on chip i2c support.
The i2c Interface provides a master-only, serial interface that can be used for initializing Tsi108/Tsi109 registers from an EEPROM after a device reset.

---
 drivers/tsi108_i2c.c |  300
++++++++++++++++++++++++++++++++++++++++++++++++++
 1 files changed, 300 insertions(+), 0 deletions(-)
drivers/tsi108_i2c.c new file +43 -0
new file mode 100644
index 0000000..08e5e3b
@@ -0,0 +1,300 @@
+/*
+ * (C) Copyright 2004 Tundra Semiconductor Corp.
+ * Author: Alex Bounine
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ *
+ */
+
+#include <config.h>
+
+#ifdef CONFIG_TSI108_I2C
+
+#include <common.h>
+#include <tsi108.h>
+
+#if (CONFIG_COMMANDS & CFG_CMD_I2C)
+
+#define I2C_DELAY           100000
+#undef  DEBUG_I2C
+
+#ifdef DEBUG_I2C
+#define DPRINT(x) printf(x)
+#else
+#define DPRINT(x)
+#endif
+
+/* All functions assume that Tsi108 I2C block is the only master on the

bus */

drivers/tsi108_i2c.c new file +28 -0
+/* I2C read helper function */
+
+static int i2c_read_byte(
+		uint i2c_chan,	/* I2C channel number: 0 - main, 1 - SDC SPD */
+		uchar chip_addr,/* I2C device address on the bus */
+		uint byte_addr,	/* Byte address within I2C device */
+		uchar * buffer	/* pointer to data buffer */
+		)
+{
+	u32 temp;
+	u32 to_count = I2C_DELAY;
+	u32 op_status = TSI108_I2C_TIMEOUT_ERR;
+	u32 chan_offset = TSI108_I2C_OFFSET;
+
+	DPRINT(("I2C read_byte() %d 0x%02x 0x%02x\n",
+		i2c_chan, chip_addr, byte_addr));
+
+	if (0 != i2c_chan) {
+		chan_offset = TSI108_I2C_SDRAM_OFFSET;
+	}
+
+	/* Check if I2C operation is in progress */
+	temp = *(u32 *) (CFG_TSI108_CSR_BASE + chan_offset + I2C_CNTRL2);
+
+	if (0 == (temp & (I2C_CNTRL2_RD_STATUS | I2C_CNTRL2_WR_STATUS |
+			  I2C_CNTRL2_START))
+	    ) {
+		/* Set device address and operation (read = 0) */

drivers/tsi108_i2c.c

Quoted 10 lines
drivers/tsi108_i2c.c new file +10 -0
+		temp = (byte_addr << 16) | ((chip_addr & 0x07) << 8) |
+		    ((chip_addr >> 3) & 0x0F);
+		*(u32 *) (CFG_TSI108_CSR_BASE + chan_offset + I2C_CNTRL1) =
+		    temp;
+
+		/* Issue the read command
+		 * (at this moment all other parameters are 0 
+		 * (size = 1 byte, lane = 0)
+		 */
+

</snip>

Your U-Boot support team