Skip to contentSkip to conversation

How do I know whether a specific driver being used?

DISCUSSION xp newbie 3 participants 5 messages Nov 5, 2006

lore
Share & tools
lore

xp newbie

author
#0 lore raw

I am using an Ubuntu system with kernel 2.6.15-27-686.

I am trying to find out whether I need to compile myself a driver for my Promise FastTrack 378 controller as described here:

http://www.linuxquestions.org/questions/showthread.php?t=362780

But before doing so, I prefer to know in advance (if possible) whether this module is already included in (and perhaps used by) the kernel.

The instructions in the README file for building this particular driver say:

------- START QUOTE -------
7.) Copy this module to
/lib/modules/2.4.x/kernel/drivers/scsi/

8.) Issue "cat /proc/scsi/ft3xx/x" (x is a SCSI host number) to get the
RAID array status.

------- END QUOTE -------

Due to different kernel I am using, the path is of course different, so I listed the modules in:

/lib/modules/2.6.15-27-686/kernel/drivers/scsi/

and found no ft3xx entry.

However, I did find a promising entry (no pun intended):

-rw-r--r-- 1 root root 16219 2006-09-15 23:49 sata_promise.ko

I then did "ls -l /proc/scsi/sata_promise" and received:
-rw-r--r-- 1 root root 0 2006-11-04 22:23 0 -rw-r--r-- 1 root root 0 2006-11-04 22:23 1 -rw-r--r-- 1 root root 0 2006-11-04 22:23 2

a 'cat' on any of these "files" yields the message:

"The driver does not yet support the proc-fs"

Please note that I am using this Promise controller to connect to a single PATA drive, not SATA.

The relevant part in my dmesg reads:

[17179575.120000] sata_promise PATA port found
[17179575.136000] ata1: SATA max UDMA/133 cmd
0xF8866200 ctl 0xF8866238 bmdma 0x0 irq 169
[17179575.140000] ata2: SATA max UDMA/133 cmd
0xF8866280 ctl 0xF88662B8 bmdma 0x0 irq 169
[17179575.140000] ata3: PATA max UDMA/133 cmd
0xF8866300 ctl 0xF8866338 bmdma 0x0 irq 169
[17179575.344000] ata1: no device found (phy stat
00000000)
[17179575.344000] scsi0 : sata_promise
[17179575.552000] ata2: no device found (phy stat
00000000)
[17179575.552000] scsi1 : sata_promise
[17179575.728000] ata3: dev 0 cfg 00:045a 49:2f00
82:346b 83:7f01 84:4003 85:3c69 86:3c01 87:4003
88:407f 93:600b
[17179575.728000] ata3: dev 0 ATA-7, max UDMA/133,
312581808 sectors: LBA48
[17179575.728000] ata3: dev 0 configured for UDMA/133
[17179575.728000] sata_get_dev_handle: SATA dev
addr=0x40000, handle=0x00000000
[17179575.728000] scsi2 : sata_promise
[17179575.728000]   Vendor: ATA       Model: SAMSUNG
SP1614N   Rev: TM10
[17179575.728000]   Type:   Direct-Access             
        ANSI SCSI revision: 05
[17179575.732000] Driver 'sd' needs updating - please
use bus_type methods
[17179575.732000] SCSI device sda: 312581808 512-byte
hdwr sectors (160042 MB)
[17179575.732000] SCSI device sda: drive cache: write
back
[17179575.732000] SCSI device sda: 312581808 512-byte
hdwr sectors (160042 MB)
[17179575.732000] SCSI device sda: drive cache: write
back
[17179575.732000]  sda: sda2 sda3 sda4 < sda5 sda6 >
[17179575.780000] sd 2:0:0:0: Attached scsi disk sda

How do I decipher all this information so that I can tell whether I am using the correct driver for this particular part of my hardware or not?

Is it possible that "the right driver" is already there and I don't have to compile anything? :)

Thanks!
Alex

____________________________________________________________________________________
Get your email and see which of your friends are online - Right on the New Yahoo.com
(http://www.yahoo.com/preview)

#1 lore raw
Quoted 8 lines · xp newbie

I am using an Ubuntu system with kernel 2.6.15-27-686.

I am trying to find out whether I need to compile myself a driver for my Promise FastTrack 378 controller as described here:

http://www.linuxquestions.org/questions/showthread.php?t=362780

This mailing list is about kernel development, this is not the right place to ask that. Anyway, 3rd party kernels, patches, drivers... are not covered here.

Quoted 4 lines

But before doing so, I prefer to know in advance (if possible) whether this module is already included in (and perhaps used by) the kernel.

Did you browse menuconfig?

Quoted 1 line

[...]

author
#2 lore raw
Quoted 7 lines · --- Miguel Ojeda

This mailing list is about kernel development, this is not the right
place to ask that. Anyway, 3rd party kernels, patches, drivers... are
not covered here.

I appologize for sending to the wrong mailing list. Could you please refer me to the correct newsgroup/forum/mailinglist?

Please note that I have already tried
http://www.ubuntuforums.org/ but the folks seem to be confused like me (regarding this particular issue).

More specifically, there is confusion between the following statement:

http://packages.debian.org/stable/devel/kernel-patch-2.4-fasttraks150

And the fact that my system shows the following:

~> lsmod | grep promise

sata_promise           12516  8
libata                 83440  1 sata_promise
scsi_mod              145960  6

sr_mod,sbp2,sg,sd_mod,sata_promise,libata

Do you know what the best place to ask such question?

Thanks!
Alex

P.S. I didn't browse menuconfig, because I am not there yet. It's like the chicken-and-the-egg
situation: I am using Ubuntu which conceptually exempts me from the need to compile kernel modules and thus menuconfig is not even installed by default. Since (thanks to Arjan's reply) I am pretty sure now that the driver is included in the distribution, I hope that no compilation is needed.

P.S.2 If I discover something that IMHO points to a bug in the kernel, where do I post it?

____________________________________________________________________________________
Get your email and see which of your friends are online - Right on the New Yahoo.com
(http://www.yahoo.com/preview)

#3 lore raw
Quoted 13 lines · xp newbie
Quoted 7 lines · --- Miguel Ojeda

This mailing list is about kernel development, this is not the right
place to ask that. Anyway, 3rd party kernels, patches, drivers... are
not covered here.

I appologize for sending to the wrong mailing list. Could you please refer me to the correct newsgroup/forum/mailinglist?

Quoted 9 lines

Please note that I have already tried
http://www.ubuntuforums.org/ but the folks seem to be confused like me (regarding this particular issue).

More specifically, there is confusion between the following statement:

http://packages.debian.org/stable/devel/kernel-patch-2.4-fasttraks150

Usually, when you have a problem with some program, you ask the developer about the bug you have found (or whatever). So you should ask Ubuntu folks, because the kernels you are using are a "fork" of the mailine kernel. They add a lot of 3rd party stuff along other things, so they are the ones who need to solve their problems. I'm sure there is someone at Ubuntu that can help you for future problems.

Quoted 13 lines

And the fact that my system shows the following:

~> lsmod | grep promise

sata_promise           12516  8
libata                 83440  1 sata_promise
scsi_mod              145960  6

sr_mod,sbp2,sg,sd_mod,sata_promise,libata

Do you know what the best place to ask such question?

Thanks!
Alex

Quoted 9 lines

P.S. I didn't browse menuconfig, because I am not there yet. It's like the chicken-and-the-egg
situation: I am using Ubuntu which conceptually exempts me from the need to compile kernel modules and thus menuconfig is not even installed by default. Since (thanks to Arjan's reply) I am pretty sure now that the driver is included in the distribution, I hope that no compilation is needed.

Well, you can browse menuconfig without compile the kernel at all... Just for check if some driver is already in. Anyway, Ubuntu kernels aren't the mailine ones and they have more drivers.

Quoted 3 lines

P.S.2 If I discover something that IMHO points to a bug in the kernel, where do I post it?

If you discover a bug in the Ubuntu kernel, you should report it to Ubuntu developers. Their kernels are "old" and very patched so they are pretty different. Only report here if the bug appears in the lastest mainline kernels (like 2.6.18 or 2.6.18.1 right now...).

Anyway, you can always use the lastest official kernel from www.kernel.org ;-) so if you find a bug you can be sure to report it here.

#4 lore raw
In reply to xp newbie
Quoted 7 lines · xp newbie

I am using an Ubuntu system with kernel 2.6.15-27-686.

I am trying to find out whether I need to compile
myself a driver for my Promise FastTrack 378
controller as described here:

http://www.linuxquestions.org/questions/showthread.php?t=362780

Hi,

no you don't need those drivers; the linux kernel and the dmraid userspace program have everything you need, no need to add weird external (and sometimes proprietary) drivers to support your software/bios raid

Greetings,
Arjan van de Ven