2.6 Kernel not mounting JFFS2 partition

DISCUSSION Glen Johnson 2 participants 6 messages Nov 16, 2006 – Nov 17, 2006 1 message not in the archive Memory technology devices (MTD)

lore

Share & tools

lore

Glen Johnson

author

2006-11-16 20:00 UTC #0 lore raw

Quoted 4 lines · Artem Bityutskiy

Hello Glen,
On Wed, 2006-11-15 at 10:55 -0500, Glen Johnson wrote:

Quoted 10 lines

Quoted 3 lines
jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at 0x00000000:
0x9b9a instead
Your problem is quite common so you inspired me to add a FAQ entry about it. Please, read
http://www.linux-mtd.infradead.org/faq/jffs2.html#L_magicnfound

Mr. Bityutskiy,
Thank you for your reply. Your FAQ answered a variety of questions for me. I went back through the process one more time following your directions and ended up with a Kernel panic. I will walk through exactly what I did and then at the bottom of this message I will include my capture log.
After I read your FAQ I looked into which flash type I am using (AM29LV3200B-90E1) which is a NOR type flash. I then powered up my target system did the following:
1. "eraseall /dev/mtd2" which ended with "Erased 2048 Kibyte @ 0 -- 100% complete."
2. cd /var/tmp
3. mkdir jffs2
4. echo 'Hello world' > jffs2/hi.txt
5. mkfs.jffs2 -d jffs2 -o jffs2.img
6. cp jffs2.img /dev/mtd2

As a step of verification I briefly read back the contents of /dev/mtd2.
7. dd if=/dev/mtd2 this produced some weird text, the filename hi.txt, some more weird text, Hello world!, and finally
a MESS of "ÿÿ". I hit ^C to cut it short. Seeing the hi.txt and Hello world! gave me the verification that I did
indeed create the jffs2 partition.
8. mount -t jffs2 mtd2 /mnt/ Once again many error messages/info messages. Finally it died with these last lines:
You cannot use older JFFS2 filesystems with newer kernels JFFS2 notice: (31) read_unknown: node header CRC failed at 0x18f070. But it must have been OK earlier.
Node totlen on flash (0xffffffff) != totlen from node ref (0x00000030) # BUG: failure at fs/jffs2/readinode.c:353/read_unknown()!

Kernel panic - not syncing: BUG!

I keep seeing "You cannot use older JFFS2 filesystems with newer kernel" however, I am using uClinux's most up to date kernel 2.6.17-uc1. Am I using an oudated fs/jffs2/readinode.c? My fs/jffs2/readinode.c claims to be at * $Id: readinode.c,v 1.143 2005/11/07 11:14:41 gleixner Exp $. Any further thoughts or recommendations would be greatly appreciated.

Capture log listed below :
=================

U-Boot 1.1.2 (Jul 11 2005 - 11:28:55)

CPU: MOTOROLA MCF5272 (Mask:1)
Board: Valcom VIP8XX
DRAM: 16 MB
FLASH: 4 MB
In: serial
Out: serial
Err: serial
Enter password to stop autoboot: 2 1 0

TFTP from server 192.168.11.111; our IP address is 192.168.11.112 Filename 'vcisc-1.03.pkg'.
Load address: 0x200000
Loading: #################################################################
#################################################################
###################################################
done
Bytes transferred = 922096 (e11f0 hex)
Automatic boot of image at addr 0x00200000 ...
## Booting image at 00200000 ...
Image Name:
Image Type: M68K Linux Kernel Image (gzip compressed)
Data Size: 922032 Bytes = 900.4 kB
Load Address: 00020000
Entry Point: 00020000
Verifying Checksum ... OK
Uncompressing Kernel Image ... OK

Starting kernel ...

Linux version 2.6.17-uc1 (glen@ekul) (gcc version 4.1.1) #8 Tue Nov 14 12:08:38 EST 2006

uClinux/COLDFIRE(m5272)
COLDFIRE port done by Greg Ungerer, [email protected]
Flat model support (C) 1998,1999 Kenneth Albanowski, D. Jeff Dionne Built 1 zonelists
Kernel command line: rootfstype=romfs
PID hash table entries: 64 (order: 6, 256 bytes)
Dentry cache hash table entries: 1024 (order: 0, 4096 bytes) Inode-cache hash table entries: 1024 (order: 0, 4096 bytes) Memory available: 6036k/8192k RAM, (1011k kernel code, 148k data) Mount-cache hash table entries: 512
NET: Registered protocol family 16
NET: Registered protocol family 2
IP route cache hash table entries: 1024 (order: 0, 4096 bytes) TCP established hash table entries: 1024 (order: 0, 4096 bytes) TCP bind hash table entries: 1024 (order: 0, 4096 bytes)
TCP: Hash tables configured (established 1024 bind 1024)
TCP reno registered
JFFS2 version 2.2. (NAND) (C) 2001-2003 Red Hat, Inc.
io scheduler noop registered
io scheduler cfq registered (default)
ColdFire internal UART serial driver version 1.00
ttyS0 at 0x10000100 (irq = 73) is a builtin ColdFire UART ttyS1 at 0x10000140 (irq = 74) is a builtin ColdFire UART RAMDISK driver initialized: 16 RAM disks of 4096K size 1024 blocksize FEC ENET Version 0.2
fec: PHY @ 0x0, ID 0x001378e2 -- LXT971
eth0: ethernet 00:00:00:00:00:00
SnapGear flash probe(0xffc00000,4194304,1): 400000 at ffc00000
Flash: Found 1 x16 devices at 0x0 in 8-bit bank
Amd/Fujitsu Extended Query Table at 0x0040
number of CFI chips: 1
cfi_cmdset_0002: Disabling erase-suspend-program due to code brokenness. Creating 3 MTD partitions on "Flash":
0x00000000-0x00080000 : "Das U-Boot"
0x00080000-0x00200000 : "Kernel"
0x00200000-0x00400000 : "JFFS2"
SnapGear ram probe(0x141fac,798720,4): c3000 at 141fac Creating 1 MTD partitions on "RAM":
0x00000000-0x000c3000 : "Romfs"
TCP bic registered
NET: Registered protocol family 1
NET: Registered protocol family 17
VFS: Mounted root (romfs filesystem) readonly.
Freeing unused kernel memory: 48k freed (0x127000 - 0x132000)
init: Failed to open /etc/inittab.# eraseall /dev/mtd2 Erasing 64 Kibyte @ 0 -- 0 % complete. ---------8<------------------8<---------
Cut out lots of the same. ---------8<------------------8<---------
Erased 2048 Kibyte @ 0 -- 100% complete.

# cd /var/tmp
# mkdir jffs2
# echo 'Hello world!' > jffs2/hi.txt
# mkfs.jffs2 -d jffs2 -o jffs2.img
# cp jffs2.img /dev/mtd2
# dd -if=/dev/mtd2
…à^A^@^@^@.N(D^@^@^@^A^@^@^@^@^@^@^@^B8C^SA^F^H^@^XAA^E"O^^ÆQhi.txtÿÿa^B^@^@^@^QE2AO^@^@^@^B^@^@^@^A^@^@^@^^@^@^@^^@^@^@^½Ý¢Ãö¥©kHello
world!
ÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿ^C
# mount -t jffs2 mtd2 /mnt/
jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at 0x00000000:
0x007c instead
Further such events for this erase block will not be printed
---------8<------------------8<---------
Cut out lots of the same.
---------8<------------------8<---------
jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at 0x001f0024:
0x4a10 instead
Further such events for this erase block will not be printed
Old JFFS2 bitmask found at 0x001fa1ec
You cannot use older JFFS2 filesystems with newer kernels
Old JFFS2 bitmask found at 0x001fda6c
You cannot use older JFFS2 filesystems with newer kernels
JFFS2 notice: (31) read_unknown: node header CRC failed at 0x18f070. But
it must have been OK earlier.
Node totlen on flash (0xffffffff) != totlen from node ref (0x00000030)
# BUG: failure at fs/jffs2/readinode.c:353/read_unknown()!
Kernel panic - not syncing: BUG!

Thank you,
Glen Johnson

Artem Bityutskiy

2006-11-17 13:11 UTC #1 lore raw

Hi,

Quoted 2 lines · Glen Johnson

1. "eraseall /dev/mtd2" which ended with "Erased 2048 Kibyte @ 0 -- 100% complete."

At this point it is nice to make sure if the erase functionality works. Try to read /dev/mtd2 and make sure it contains only 0xFFs.

Quoted 3 lines

8. mount -t jffs2 mtd2 /mnt/ Once again many error messages/info messages. Finally it died with these last lines:
You cannot use older JFFS2 filesystems with newer kernels

Download newer JFFS2 utilities and use newer mkfs.jffs2. It will probably solve your problems.

Signature · 2 lines

Best regards,
Artem Bityutskiy (Битюцкий Артём)

A message that is not in the archive (sent off-list or not yet received): [email protected]

Artem Bityutskiy

2006-11-17 14:22 UTC #3 lore raw

Quoted 7 lines · Glen Johnson

I am using uClinux so I may be moving out of the realm of linux-mtd. I went to the Red Hat JFFS2 web
site, and used cvs to download the source for the "latest JFFS2 source". How do I get this code to
compile with the uClinux way of doing things. I tried the script and it seems to patch the code for a
normal Linux distro. Advice on this would be most helpful.

We moved to GIT. The utilities are available via

git-clone git://git.infradead.org/mtd-utils.git mtd-utils.git

command. Also see http://www.linux-mtd.infradead.org/doc/git.html

Signature · 2 lines

Best regards,
Artem Bityutskiy (Битюцкий Артём)

Glen Johnson

author

2006-11-17 16:28 UTC #4 lore raw

Quoted 7 lines · Artem Bityutskiy

We moved to GIT. The utilities are available via
git-clone git://git.infradead.org/mtd-utils.git mtd-utils.git
command. Also see http://www.linux-mtd.infradead.org/doc/git.html

Mr. Bityutskiy,
After using git-clone ... I replaced uClinux-dist/user/mtd-utils with the git-clone you recommended. I tried make
and received the following error.

make[3]: Entering directory `/home/glen/src/c/uClinux-dist-20060803/user/mtd-utils' mkdir -p m68k-elf
m68k-elf-gcc -I./include -O2 -Wall -g -c -o m68k-elf/mkfs.jffs2.o mkfs.jffs2.c -g -Wp,-MD,m68k-elf/.mkfs.jffs2.c.dep mkfs.jffs2.c:69:21: error: sys/acl.h: No such file or directory mkfs.jffs2.c:73:18: error: zlib.h: No such file or directory

Is there something I need to update in make xconfig to get the proper header files to be included? I am sure there is
something I am leaving out.
Thanks,
Glen Johnson

Artem Bityutskiy

2006-11-17 16:36 UTC #5 lore raw

Quoted 7 lines · Glen Johnson

make[3]: Entering directory `/home/glen/src/c/uClinux-dist-20060803/user/mtd-utils' mkdir -p m68k-elf
m68k-elf-gcc -I./include -O2 -Wall -g -c -o m68k-elf/mkfs.jffs2.o mkfs.jffs2.c -g -Wp,-MD,m68k-elf/.mkfs.jffs2.c.dep mkfs.jffs2.c:69:21: error: sys/acl.h: No such file or directory mkfs.jffs2.c:73:18: error: zlib.h: No such file or directory

Sorry, no idea. Try ti fix this yourself or may be somebody from this list will help you.

Signature · 2 lines

Best regards,
Artem Bityutskiy (Битюцкий Артём)

Glen Johnson

author

2006-11-17 16:39 UTC #6 lore raw

In reply to Artem Bityutskiy

Quoted 6 lines · Artem Bityutskiy

Quoted 4 lines
We moved to GIT. The utilities are available via
git-clone git://git.infradead.org/mtd-utils.git mtd-utils.git

Mr. Bityutskiy,
After using git-clone ... I replaced uClinux-dist/user/mtd-utils with the git-clone you recommended. I tried make
and received the following error.

Is there something I need to update in make xconfig to get the proper header files to be included? I am sure there is
something I am leaving out.
Thanks,
Glen Johnson