Skip to contentSkip to conversation

Blackfin: serial driver for Blackfin architecture against Linux kernel 2.6.20

PATCH New Wu, Bryan 1 participant 1 message Feb 8, 2007 TTY layer and serial drivers

lore
Share & tools
lore

Wu, Bryan

author
#0 lore raw

PATCH 2/3 Blackfin: serial driver for Blackfin architecture against Linux kernel 2.6.20

Hi forks,

Aubrey update the patch according to Russell's review. Thanks Russell Here is the change log:

a) arrange the driver to reflect the real settings in the termios
b) don't use __builtin_bfin_ssync(), directly use SSYNC() instead

---

drivers/serial/Kconfig      |   94 ++++
drivers/serial/Makefile     |    1
drivers/serial/bfin_5xx.c   |  997 ++++++++++++++++++++++++++++++++++++++++++++
include/linux/serial_core.h |    3
4 files changed, 1095 insertions(+)
drivers/serial/Kconfig +94 -0
Index: linux-2.6/drivers/serial/Kconfig 
===================================================================
@@ -498,6 +498,100 @@
 	  your boot loader (lilo or loadlin) about how to pass options to the
 	  kernel at boot time.)
 
+config SERIAL_BFIN
+	tristate "Blackfin serial port support (EXPERIMENTAL)"
+	depends on BFIN && EXPERIMENTAL
+	select SERIAL_CORE
+	select SERIAL_BFIN_UART0 if (BF531 || BF532 || BF533 || BF561)
+	help
+	  Add support for the built-in UARTs on the Blackfin.
+
+	  To compile this driver as a module, choose M here: the
+	  module will be called bfin_5xx.
+
+config SERIAL_BFIN_CONSOLE
+	bool "Console on Blackfin serial port"
+	depends on SERIAL_BFIN
+	select SERIAL_CORE_CONSOLE
+
+choice
+	prompt  "Blackfin UART Mode"
+	depends on SERIAL_BFIN
+	default SERIAL_BFIN_DMA
+	help
+	  This driver supports the built-in serial ports of the Blackfin family
+	  of CPUs
+
+config SERIAL_BFIN_DMA
+	bool "Blackfin UART DMA mode"
+	depends on DMA_UNCACHED_1M
+	help
+	  This driver works under DMA mode. If this option is selected, the
+	  blackfin simple dma driver is also enabled.
+
+config SERIAL_BFIN_PIO
+	bool "Blackfin UART PIO mode"
+	help
+	  This driver works under PIO mode.
+
+endchoice
+
+config SERIAL_BFIN_UART0
+	bool "Enable UART0"
+	depends on SERIAL_BFIN
+	help
+	  Enable UART0
+
+config BFIN_UART0_CTSRTS
+	bool "Enable UART0 hardware flow control"
+	depends on SERIAL_BFIN_UART0
+	help
+	  Enable hardware flow control in the driver. Using GPIO emulate the CTS/RTS
+	  signal.
+
+config UART0_CTS_PIN
+	int "UART0 CTS pin"
+	depends on BFIN_UART0_CTSRTS
+	default 23
+	help
+	  The default pin is GPIO_GP7.
+	  Refer to ./include/asm-blackfin/gpio.h to see the GPIO map.
+
+config UART0_RTS_PIN
+	int "UART0 RTS pin"
+	depends on BFIN_UART0_CTSRTS
+	default 22
+	help
+	  The default pin is GPIO_GP6.
+	  Refer to ./include/asm-blackfin/gpio.h to see the GPIO map.
+
+config SERIAL_BFIN_UART1
+	bool "Enable UART1"
+	depends on SERIAL_BFIN && BF537
+	help
+	  Enable UART1
+
+config BFIN_UART1_CTSRTS
+	bool "Enable UART1 hardware flow control"
+	depends on SERIAL_BFIN_UART1
+	help
+	  Enable hardware flow control in the driver. Using GPIO emulate the CTS/RTS
+	  signal.
+
+config UART1_CTS_PIN
+	int "UART1 CTS pin"
+	depends on BFIN_UART1_CTSRTS
+	default -1
+	help
+	  Refer to ./include/asm-blackfin/gpio.h to see the GPIO map.
+
+config UART1_RTS_PIN
+	int "UART1 RTS pin"
+	depends on BFIN_UART1_CTSRTS
+	default -1
+	help
+	  Refer to ./include/asm-blackfin/gpio.h to see the GPIO map.
+
 config SERIAL_IMX
 	bool "IMX serial port support"
 	depends on ARM && ARCH_IMX
drivers/serial/Makefile +1 -0
Index: linux-2.6/drivers/serial/Makefile
===================================================================
@@ -26,6 +26,7 @@
 obj-$(CONFIG_SERIAL_CLPS711X) += clps711x.o
 obj-$(CONFIG_SERIAL_PXA) += pxa.o
 obj-$(CONFIG_SERIAL_SA1100) += sa1100.o
+obj-$(CONFIG_SERIAL_BFIN) += bfin_5xx.o
 obj-$(CONFIG_SERIAL_S3C2410) += s3c2410.o
 obj-$(CONFIG_SERIAL_SUNCORE) += suncore.o
 obj-$(CONFIG_SERIAL_SUNHV) += sunhv.o
drivers/serial/bfin_5xx.c new file +997 -0

997 lines not on this page · raw message

include/linux/serial_core.h +3 -0
Index: linux-2.6/include/linux/serial_core.h
===================================================================
@@ -135,6 +135,9 @@
 /* Xilinx uartlite */
 #define PORT_UARTLITE	74
 
+/* Blackfin bf5xx */
+#define PORT_BFIN	75
+
 #ifdef __KERNEL__
 
 #include <linux/compiler.h>

---

Thanks a lot
Best Regards,
Bryan Wu <[email protected]>