Skip to contentSkip to conversation

ASoC documentation updates

PATCH New Liam Girdwood 1 participant 1 message Feb 8, 2007 Documentation

lore
Share & tools
lore
#0 lore raw

PATCH 1/1 ASoC documentation updates

This patch updates the documentation for ASoC to reflect the recent changes in API between 0.12.x and 0.13.x

Changes:-

o Removed all reference to old API's.
o Removed references and examples of automatic DAI config and matching.
o Fixed 80 char line length on some files.

Documentation/soc/DAI.txt +0 -490
diff -r 693e2a521575 Documentation/soc/DAI.txt
@@ -54,493 +54,3 @@ Common PCM operating modes:-
  o Mode A - MSB is transmitted on falling edge of first BCLK after FRAME/SYNC.
 
  o Mode B - MSB is transmitted on rising edge of FRAME/SYNC.
-
-
-ASoC DAI Configuration
-======================
-
-Every CODEC DAI and SoC DAI must have their capabilities defined in order to
-be configured together at runtime when the audio and clocking parameters are
-known. This is achieved by creating an array of struct snd_soc_hw_mode in the
-the CODEC and SoC interface drivers. Each element in the array describes a DAI
-mode and each mode is usually based upon the DAI system clock to sample rate
-ratio (FS).
-
-i.e. 48k sample rate @ 256 FS = sytem clock of 12.288 MHz
-     48000 * 256 = 12288000
-
-The CPU and Codec DAI modes are then ANDed together at runtime to determine the
-rutime DAI configuration for both the Codec and CPU.
-
-When creating a new codec or SoC DAI it's probably best to start of with a few
-sample rates first and then test your interface.
-
-struct snd_soc_dai_mode is defined (in soc.h) as:-
-
-/* SoC DAI mode */
-struct snd_soc_dai_mode {
-	u16 fmt;		/* SND_SOC_DAIFMT_* */
-	u16 tdm;		/* SND_SOC_HWTDM_* */
-	u64 pcmfmt; 	/* SNDRV_PCM_FMTBIT_* */
-	u16 pcmrate;	/* SND_SOC_HWRATE_* */
-	u16 pcmdir:2;	/* SND_SOC_HWDIR_* */
-	u16 flags:8;	/* hw flags */
-	u16 fs;			/* mclk to rate divider */
-	u64 bfs;		/* mclk to bclk dividers */
-	unsigned long priv;		/* private mode data */
-};
-
-fmt:
-----
-This field defines the DAI mode hardware format (e.g. I2S settings) and
-supports the following settings:-
-
- 1) hardware DAI formats
-
-#define SND_SOC_DAIFMT_I2S        (1 << 0)	/* I2S mode */
-#define SND_SOC_DAIFMT_RIGHT_J    (1 << 1)	/* Right justified mode */
-#define SND_SOC_DAIFMT_LEFT_J     (1 << 2)	/* Left Justified mode */
-#define SND_SOC_DAIFMT_DSP_A      (1 << 3)	/* L data msb after FRM */
-#define SND_SOC_DAIFMT_DSP_B      (1 << 4)	/* L data msb during FRM */
-#define SND_SOC_DAIFMT_AC97       (1 << 5)	/* AC97 */
-
- 2) hw DAI signal inversions
-
-#define SND_SOC_DAIFMT_NB_NF		(1 << 8)	/* normal bit clock + frame */
-#define SND_SOC_DAIFMT_NB_IF		(1 << 9)	/* normal bclk + inv frm */
-#define SND_SOC_DAIFMT_IB_NF		(1 << 10)	/* invert bclk + nor frm */
-#define SND_SOC_DAIFMT_IB_IF		(1 << 11)	/* invert bclk + frm */
-
- 3) hw clock masters
-    This is wrt the codec, the inverse is true for the interface
-    i.e. if the codec is clk and frm master then the interface is
-    clk and frame slave.
-
-#define SND_SOC_DAIFMT_CBM_CFM		(1 << 12)	/* codec clk & frm master */
-#define SND_SOC_DAIFMT_CBS_CFM		(1 << 13)	/* codec clk slave & frm master */
-#define SND_SOC_DAIFMT_CBM_CFS		(1 << 14)	/* codec clk master & frame slave */
-#define SND_SOC_DAIFMT_CBS_CFS		(1 << 15)	/* codec clk & frm slave */
-
-At least one option from each section must be selected. Multiple selections are
-also supported e.g.
-
- .fmt = SND_SOC_DAIFMT_I2S | SND_SOC_DAIFMT_LEFT_J | SND_SOC_DAIFMT_RIGHT_J | \
-	SND_SOC_DAIFMT_NB_NF | SND_SOC_DAIFMT_NB_IF | SND_SOC_DAIFMT_IB_NF | \
-	SND_SOC_DAIFMT_IB_IF
-
-
-tdm:
-------
-This field defines the Time Division Multiplexing left and right word
-positions for the DAI mode if applicable. Set to SND_SOC_DAITDM_LRDW(0,0) for
-no TDM.
-
-
-pcmfmt:
----------
-The hardware PCM format. This describes the PCM formats supported by the DAI
-mode e.g.
-
- .pcmfmt = SNDRV_PCM_FORMAT_S16_LE | SNDRV_PCM_FORMAT_S20_3LE | \
- 	SNDRV_PCM_FORMAT_S24_3LE
-
-pcmrate:
-----------
-The PCM sample rates supported by the DAI mode. e.g.
-
- .pcmrate = SNDRV_PCM_RATE_8000 | SNDRV_PCM_RATE_11025 | SNDRV_PCM_RATE_16000 | \
-	SNDRV_PCM_RATE_22050 | SNDRV_PCM_RATE_32000 | SNDRV_PCM_RATE_44100 | \
-	SNDRV_PCM_RATE_48000 | SNDRV_PCM_RATE_88200 | SNDRV_PCM_RATE_96000
-
-
-pcmdir:
----------
-The stream directions supported by this mode. e.g. playback and capture
-
-
-flags:
---------
-The DAI hardware flags supported by the mode.
-
-/* use bfs mclk divider mode (BCLK = MCLK / x) */
-#define SND_SOC_DAI_BFS_DIV		0x1
-/* use bfs rate mulitplier  (BCLK = RATE * x)*/
-#define SND_SOC_DAI_BFS_RATE	0x2
-/* use bfs rcw multiplier (BCLK = RATE * CHN * WORD SIZE) */
-#define SND_SOC_DAI_BFS_RCW		0x4
-/* capture and playback can use different clocks */
-#define SND_SOC_DAI_ASYNC		0x8
-
-NOTE: Bitclock division and mulitiplication modes can be safely matched by the
-core logic.
-
-
-fs:
------
-The FS supported by this DAI mode FS is the ratio between the system clock and
-the sample rate. See above
-
-bfs:
-------
-BFS is the ratio of BCLK to MCLK or the ratio of BCLK to sample rate (this
-depends on the codec or CPU DAI).
-
-The BFS supported by the DAI mode. This can either be the ratio between the
-bitclock (BCLK) and the sample rate OR the ratio between the system clock and
-the sample rate. Depends on the flags above.
-
-priv:
------
-private codec mode data.
-
-
-
-Examples
-========
-
-Note that Codec DAI and CPU DAI examples are interchangeable in these examples
-as long as the bus master is reversed. i.e.
-
-  SND_SOC_DAIFMT_CBM_CFM would become SND_SOC_DAIFMT_CBS_CFS
-  and vice versa.
-
-This applies to all SND_SOC_DAIFMT_CB*_CF*.
-
-Example 1
----------
-
-Simple codec that only runs at 8k & 48k @ 256FS in master mode, can generate a
-BCLK of either MCLK/2 or MCLK/4.
-
-	/* codec master */
-	{
-		.fmt = SND_SOC_DAIFMT_I2S | SND_SOC_DAIFMT_CBM_CFM,
-		.pcmfmt = SNDRV_PCM_FORMAT_S16_LE,
-		.pcmrate = SNDRV_PCM_RATE_8000 | SNDRV_PCM_RATE_48000,
-		.pcmdir = SND_SOC_DAIDIR_PLAYBACK | SND_SOC_DAIDIR_CAPTURE,
-		.flags = SND_SOC_DAI_BFS_DIV,
-		.fs = 256,
-		.bfs = SND_SOC_FSBD(2) | SND_SOC_FSBD(4),
-	}
-
-
-Example 2
----------
-Simple codec that only runs at 8k & 48k @ 256FS in master mode, can generate a
-BCLK of either Rate * 32 or Rate * 64.
-
-	/* codec master */
-	{
-		.fmt = SND_SOC_DAIFMT_I2S | SND_SOC_DAIFMT_CBM_CFM,
-		.pcmfmt = SNDRV_PCM_FORMAT_S16_LE,
-		.pcmrate = SNDRV_PCM_RATE_8000 | SNDRV_PCM_RATE_48000,
-		.pcmdir = SND_SOC_DAIDIR_PLAYBACK | SND_SOC_DAIDIR_CAPTURE,
-		.flags = SND_SOC_DAI_BFS_RATE,
-		.fs = 256,
-		.bfs = 32,
-	},
-	{
-		.fmt = SND_SOC_DAIFMT_I2S | SND_SOC_DAIFMT_CBM_CFM,
-		.pcmfmt = SNDRV_PCM_FORMAT_S16_LE,
-		.pcmrate = SNDRV_PCM_RATE_8000 | SNDRV_PCM_RATE_48000,
-		.pcmdir = SND_SOC_DAIDIR_PLAYBACK | SND_SOC_DAIDIR_CAPTURE,
-		.flags = SND_SOC_DAI_BFS_RATE,
-		.fs = 256,
-		.bfs = 64,
-	},
-
-
-Example 3
----------
-Codec that runs at 8k & 48k @ 256FS in master mode, can generate a BCLK that
-is a multiple of Rate * channels * word size. (RCW) i.e.
-
-	BCLK = 8000 * 2 * 16 (8k, stereo, 16bit)
-	     = 256kHz
-
-This codecs supports a RCW multiple of 1,2
-
-	{
-		.fmt = SND_SOC_DAIFMT_I2S | SND_SOC_DAIFMT_CBM_CFM,
-		.pcmfmt = SNDRV_PCM_FORMAT_S16_LE,
-		.pcmrate = SNDRV_PCM_RATE_8000 | SNDRV_PCM_RATE_48000,
-		.pcmdir = SND_SOC_DAIDIR_PLAYBACK | SND_SOC_DAIDIR_CAPTURE,
-		.flags = SND_SOC_DAI_BFS_RCW,
-		.fs = 256,
-		.bfs = SND_SOC_FSBW(1) | SND_SOC_FSBW(2),
-	}
-
-
-Example 4
----------
-Codec that only runs at 8k & 48k @ 256FS in master mode, can generate a
-BCLK of either Rate * 32 or Rate * 64. Codec can also run in slave mode as long
-as BCLK is rate * 32 or rate * 64.
-
-	/* codec master */
-	{
-		.fmt = SND_SOC_DAIFMT_I2S | SND_SOC_DAIFMT_CBM_CFM,
-		.pcmfmt = SNDRV_PCM_FORMAT_S16_LE,
-		.pcmrate = SNDRV_PCM_RATE_8000 | SNDRV_PCM_RATE_48000,
-		.pcmdir = SND_SOC_DAIDIR_PLAYBACK | SND_SOC_DAIDIR_CAPTURE,
-		.flags = SND_SOC_DAI_BFS_RATE,
-		.fs = 256,
-		.bfs = 32,
-	},
-	{
-		.fmt = SND_SOC_DAIFMT_I2S | SND_SOC_DAIFMT_CBM_CFM,
-		.pcmfmt = SNDRV_PCM_FORMAT_S16_LE,
-		.pcmrate = SNDRV_PCM_RATE_8000 | SNDRV_PCM_RATE_48000,
-		.pcmdir = SND_SOC_DAIDIR_PLAYBACK | SND_SOC_DAIDIR_CAPTURE,
-		.flags = SND_SOC_DAI_BFS_RATE,
-		.fs = 256,
-		.bfs = 64,
-	},
-
-	/* codec slave */
-	{
-		.fmt = SND_SOC_DAIFMT_I2S | SND_SOC_DAIFMT_CBS_CFS,
-		.pcmfmt = SNDRV_PCM_FORMAT_S16_LE,
-		.pcmdir = SNDRV_PCM_RATE_8000 | SNDRV_PCM_RATE_48000,
-		.pcmdir = SND_SOC_DAIDIR_PLAYBACK | SND_SOC_DAIDIR_CAPTURE,
-		.flags = SND_SOC_DAI_BFS_RATE,
-		.fs = SND_SOC_FS_ALL,
-		.bfs = 32,
-	},
-	{
-		.fmt = SND_SOC_DAIFMT_I2S | SND_SOC_DAIFMT_CBS_CFS,
-		.pcmfmt = SNDRV_PCM_FORMAT_S16_LE,
-		.pcmdir = SNDRV_PCM_RATE_8000 | SNDRV_PCM_RATE_48000,
-		.pcmdir = SND_SOC_DAIDIR_PLAYBACK | SND_SOC_DAIDIR_CAPTURE,
-		.flags = SND_SOC_DAI_BFS_RATE,
-		.fs = SND_SOC_FS_ALL,
-		.bfs = 64,
-	},
-
-
-Example 5
----------
-Codec that only runs at 8k, 16k, 32k, 48k, 96k @ 128FS, 192FS & 256FS in master
-mode and can generate a BCLK of MCLK / (1,2,4,8,16). Codec can also run in slave
-mode as and does not care about FS or BCLK (as long as there is enough bandwidth).
-
-	#define CODEC_FSB \
-	(SND_SOC_FSBD(1) | SND_SOC_FSBD(2) | SND_SOC_FSBD(4) | \
-	SND_SOC_FSBD(8) | SND_SOC_FSBD(16))
-
-	#define CODEC_RATES \
-	(SNDRV_PCM_RATE_8000 | SNDRV_PCM_RATE_16000 | SNDRV_PCM_RATE_32000 |\
-	 SNDRV_PCM_RATE_48000 | SNDRV_PCM_RATE_96000)
-
-	/* codec master @ 128, 192 & 256 FS */
-	{
-		.fmt = SND_SOC_DAIFMT_I2S | SND_SOC_DAIFMT_CBM_CFM,
-		.pcmfmt = SNDRV_PCM_FORMAT_S16_LE,
-		.pcmrate = CODEC_RATES,
-		.pcmdir = SND_SOC_DAIDIR_PLAYBACK | SND_SOC_DAIDIR_CAPTURE,
-		.flags = SND_SOC_DAI_BFS_DIV,
-		.fs = 128,
-		.bfs = CODEC_FSB,
-	},
-
-	{
-		.fmt = SND_SOC_DAIFMT_I2S | SND_SOC_DAIFMT_CBM_CFM,
-		.pcmfmt = SNDRV_PCM_FORMAT_S16_LE,
-		.pcmrate = CODEC_RATES,
-		.pcmdir = SND_SOC_DAIDIR_PLAYBACK | SND_SOC_DAIDIR_CAPTURE,
-		.flags = SND_SOC_DAI_BFS_DIV,
-		.fs = 192,
-		.bfs = CODEC_FSB
-	},
-
-	{
-		.fmt = SND_SOC_DAIFMT_I2S | SND_SOC_DAIFMT_CBM_CFM,
-		.pcmfmt = SNDRV_PCM_FORMAT_S16_LE,
-		.pcmrate = CODEC_RATES,
-		.pcmdir = SND_SOC_DAIDIR_PLAYBACK | SND_SOC_DAIDIR_CAPTURE,
-		.flags = SND_SOC_DAI_BFS_DIV,
-		.fs = 256,
-		.bfs = CODEC_FSB,
-	},
-
-	/* codec slave */
-	{
-		.fmt = SND_SOC_DAIFMT_I2S | SND_SOC_DAIFMT_CBS_CFS,
-		.pcmfmt = SNDRV_PCM_FORMAT_S16_LE,
-		.pcmrate = CODEC_RATES,
-		.pcmdir = SND_SOC_DAIDIR_PLAYBACK | SND_SOC_DAIDIR_CAPTURE,
-		.fs = SND_SOC_FS_ALL,
-		.bfs = SND_SOC_FSB_ALL,
-	},
-
-
-Example 6
----------
-Codec that only runs at 8k, 44.1k, 48k @ different FS in master mode (for use
-with a fixed MCLK) and can generate a BCLK of MCLK / (1,2,4,8,16).
-Codec can also run in slave mode as and does not care about FS or BCLK (as long
-as there is enough bandwidth). Codec can support 16, 24 and 32 bit PCM sample
-sizes.
-
-	#define CODEC_FSB \
-	(SND_SOC_FSBD(1) | SND_SOC_FSBD(2) | SND_SOC_FSBD(4) | \
-	SND_SOC_FSBD(8) | SND_SOC_FSBD(16))
-
-	#define CODEC_PCM_FORMATS \
-	(SNDRV_PCM_FORMAT_S16_LE | SNDRV_PCM_FORMAT_S20_3LE | \
-	SNDRV_PCM_FORMAT_S24_3LE | SNDRV_PCM_FORMAT_S24_LE | SNDRV_PCM_FORMAT_S32_LE)
-
-	/* codec master */
-	{
-		.fmt = SND_SOC_DAIFMT_I2S | SND_SOC_DAIFMT_CBM_CFM,
-		.pcmfmt = SNDRV_PCM_FORMAT_S16_LE,
-		.pcmrate = SNDRV_PCM_RATE_8000,
-		.pcmdir = SND_SOC_DAIDIR_PLAYBACK | SND_SOC_DAIDIR_CAPTURE,
-		.flags = SND_SOC_DAI_BFS_DIV,
-		.fs = 1536,
-		.bfs = CODEC_FSB,
-	},
-
-	{
-		.fmt = SND_SOC_DAIFMT_I2S | SND_SOC_DAIFMT_CBM_CFM,
-		.pcmfmt = SNDRV_PCM_FORMAT_S16_LE,
-		.pcmrate = SNDRV_PCM_RATE_44100,
-		.pcmdir = SND_SOC_DAIDIR_PLAYBACK | SND_SOC_DAIDIR_CAPTURE,
-		.flags = SND_SOC_DAI_BFS_DIV,
-		.fs = 272,
-		.bfs = CODEC_FSB,
-	},
-
-	{
-		.fmt = SND_SOC_DAIFMT_I2S | SND_SOC_DAIFMT_CBM_CFM,
-		.pcmfmt = SNDRV_PCM_FORMAT_S16_LE,
-		.pcmrate = SNDRV_PCM_RATE_48000,
-		.pcmdir = SND_SOC_DAIDIR_PLAYBACK | SND_SOC_DAIDIR_CAPTURE,
-		.flags = SND_SOC_DAI_BFS_DIV,
-		.fs = 256,
-		.bfs = CODEC_FSB,
-	},
-
-	/* codec slave */
-	{
-		.fmt = SND_SOC_DAIFMT_I2S | SND_SOC_DAIFMT_CBS_CFS,
-		.pcmfmt = SNDRV_PCM_FORMAT_S16_LE,
-		.pcmrate = CODEC_RATES,
-		.pcmdir = SND_SOC_DAIDIR_PLAYBACK | SND_SOC_DAIDIR_CAPTURE,
-		.fs = SND_SOC_FS_ALL,
-		.bfs = SND_SOC_FSB_ALL,
-	},
-
-
-Example 7
----------
-AC97 Codec that does not support VRA (i.e only runs at 48k).
-
-	#define AC97_DIR \
-	(SND_SOC_DAIDIR_PLAYBACK | SND_SOC_DAIDIR_CAPTURE)
-
-	#define AC97_PCM_FORMATS \
-	(SNDRV_PCM_FORMAT_S16_LE | SNDRV_PCM_FORMAT_S18_3LE | \
-	SNDRV_PCM_FORMAT_S20_3LE)
-
-	/* AC97 with no VRA */
-	{
-		.pcmfmt = AC97_PCM_FORMATS,
-		.pcmrate = SNDRV_PCM_RATE_48000,
-	}
-
-
-Example 8
----------
-
-CPU DAI that supports 8k - 48k @ 256FS and BCLK = MCLK / 4 in master mode.
-Slave mode (CPU DAI is FRAME master) supports 8k - 96k at any FS as long as
-BCLK = 64 * rate. (Intel XScale I2S controller).
-
-	#define PXA_I2S_DAIFMT \
-	(SND_SOC_DAIFMT_I2S | SND_SOC_DAIFMT_LEFT_J | SND_SOC_DAIFMT_NB_NF)
-
-	#define PXA_I2S_DIR \
-	(SND_SOC_DAIDIR_PLAYBACK | SND_SOC_DAIDIR_CAPTURE)
-
-	#define PXA_I2S_RATES \
-	(SNDRV_PCM_RATE_8000 | SNDRV_PCM_RATE_11025 | SNDRV_PCM_RATE_16000 | \
-	SNDRV_PCM_RATE_22050 | SNDRV_PCM_RATE_32000 | SNDRV_PCM_RATE_44100 | \
-	SNDRV_PCM_RATE_48000 | SNDRV_PCM_RATE_88200 | SNDRV_PCM_RATE_96000)
-
-	/* priv is divider */
-	static struct snd_soc_dai_mode pxa2xx_i2s_modes[] = {
-	/* pxa2xx I2S frame and clock master modes */
-	{
-		.fmt = PXA_I2S_DAIFMT | SND_SOC_DAIFMT_CBS_CFS,
-		.pcmfmt = SNDRV_PCM_FMTBIT_S16_LE,
-		.pcmrate = SNDRV_PCM_RATE_8000,
-		.pcmdir = PXA_I2S_DIR,
-		.flags = SND_SOC_DAI_BFS_DIV,
-		.fs = 256,
-		.bfs = SND_SOC_FSBD(4),
-		.priv = 0x48,
-	},
-	{
-		.fmt = PXA_I2S_DAIFMT | SND_SOC_DAIFMT_CBS_CFS,
-		.pcmfmt = SNDRV_PCM_FMTBIT_S16_LE,
-		.pcmrate = SNDRV_PCM_RATE_11025,
-		.pcmdir = PXA_I2S_DIR,
-		.flags = SND_SOC_DAI_BFS_DIV,
-		.fs = 256,
-		.bfs = SND_SOC_FSBD(4),
-		.priv = 0x34,
-	},
-	{
-		.fmt = PXA_I2S_DAIFMT | SND_SOC_DAIFMT_CBS_CFS,
-		.pcmfmt = SNDRV_PCM_FMTBIT_S16_LE,
-		.pcmrate = SNDRV_PCM_RATE_16000,
-		.pcmdir = PXA_I2S_DIR,
-		.flags = SND_SOC_DAI_BFS_DIV,
-		.fs = 256,
-		.bfs = SND_SOC_FSBD(4),
-		.priv = 0x24,
-	},
-	{
-		.fmt = PXA_I2S_DAIFMT | SND_SOC_DAIFMT_CBS_CFS,
-		.pcmfmt = SNDRV_PCM_FMTBIT_S16_LE,
-		.pcmrate = SNDRV_PCM_RATE_22050,
-		.pcmdir = PXA_I2S_DIR,
-		.flags = SND_SOC_DAI_BFS_DIV,
-		.fs = 256,
-		.bfs = SND_SOC_FSBD(4),
-		.priv = 0x1a,
-	},
-	{
-		.fmt = PXA_I2S_DAIFMT | SND_SOC_DAIFMT_CBS_CFS,
-		.pcmfmt = SNDRV_PCM_FMTBIT_S16_LE,
-		.pcmrate = SNDRV_PCM_RATE_44100,
-		.pcmdir = PXA_I2S_DIR,
-		.flags = SND_SOC_DAI_BFS_DIV,
-		.fs = 256,
-		.bfs = SND_SOC_FSBD(4),
-		.priv = 0xd,
-	},
-	{
-		.fmt = PXA_I2S_DAIFMT | SND_SOC_DAIFMT_CBS_CFS,
-		.pcmfmt = SNDRV_PCM_FMTBIT_S16_LE,
-		.pcmrate = SNDRV_PCM_RATE_48000,
-		.pcmdir = PXA_I2S_DIR,
-		.flags = SND_SOC_DAI_BFS_DIV,
-		.fs = 256,
-		.bfs = SND_SOC_FSBD(4),
-		.priv = 0xc,
-	},
-
-	/* pxa2xx I2S frame master and clock slave mode */
-	{
-		.fmt = PXA_I2S_DAIFMT | SND_SOC_DAIFMT_CBM_CFS,
-		.pcmfmt = SNDRV_PCM_FMTBIT_S16_LE,
-		.pcmrate = PXA_I2S_RATES,
-		.pcmdir = PXA_I2S_DIR,
-		.fs = SND_SOC_FS_ALL,
-		.flags = SND_SOC_DAI_BFS_RATE,
-		.bfs = 64,
-		.priv = 0x48,
-	},
-};
Documentation/soc/clocking.txt +5 -268

280 lines not on this page · raw message

Documentation/soc/codec.txt +36 -71

171 lines not on this page · raw message

Documentation/soc/machine.txt +1 -2
diff -r 693e2a521575 Documentation/soc/machine.txt
@@ -64,7 +64,7 @@ static struct snd_soc_dai_link corgi_dai
 	.cpu_dai = &pxa_i2s_dai,
 	.codec_dai = &wm8731_dai,
 	.init = corgi_wm8731_init,
-	.config_sysclk = corgi_config_sysclk,
+	.ops = &corgi_ops,
 };
 
 struct snd_soc_machine then sets up the machine with it's DAI's. e.g.
@@ -74,7 +74,6 @@ static struct snd_soc_machine snd_soc_ma
 	.name = "Corgi",
 	.dai_link = &corgi_dai,
 	.num_links = 1,
-	.ops = &corgi_ops,
 };
 
 
Documentation/soc/pops_clicks.txt +6 -6
diff -r 693e2a521575 Documentation/soc/pops_clicks.txt
@@ -2,14 +2,14 @@ Audio Pops and Clicks
 =====================
 
 Pops and clicks are unwanted audio artifacts caused by the powering up and down
-of components within the audio subsystem. This is noticable on PC's when an audio
-module is either loaded or unloaded (at module load time the sound card is
+of components within the audio subsystem. This is noticable on PC's when an
+audio module is either loaded or unloaded (at module load time the sound card is
 powered up and causes a popping noise on the speakers).
 
-Pops and clicks can be more frequent on portable systems with DAPM. This is because
-the components within the subsystem are being dynamically powered depending on
-the audio usage and this can subsequently cause a small pop or click every time a
-component power state is changed.
+Pops and clicks can be more frequent on portable systems with DAPM. This is
+because the components within the subsystem are being dynamically powered
+depending on the audio usage and this can subsequently cause a small pop or
+click every time a component power state is changed.
 
 
 Minimising Playback Pops and Clicks

-------------------------------------------------------------------------
Using Tomcat but need to do more? Need to support web services, security? Get stuff done quickly with pre-integrated technology to make your job easier. Download IBM WebSphere Application Server v.1.0.1 based on Apache Geronimo
http://sel.as-us.falkag.net/sel?cmd=lnk&kid=120709&bid=263057&dat=121642

_______________________________________________
Alsa-devel mailing list
[email protected]
https://lists.sourceforge.net/lists/listinfo/alsa-devel