hda-intel without headphone output
hi everyone,
i have a fujitsu siemens amilo pro v3515 notebook, with a via VT8251/ VT8237A chipset. sound works fine through the speakers, but i don't get anything through the headphones, no headphone channel shows up in the mixer, and the headphone jack switch doesn't mute the speakers. i have alsa 1.0.13, and a 2.6.18 kernel. i tried all "model" settings that i could find in ALSA-Configuration in the kernel tree. lspci -nv gives
04:01.0 0403: 1106:3288 (rev 10)
Subsystem: 1734:10cb
Flags: bus master, fast devsel, latency 0, IRQ 58
Memory at c9100000 (64-bit, non-prefetchable) [size=16K]
Capabilities: [50] Power Management version 2
Capabilities: [60] Message Signalled Interrupts: Mask- 64bit+ Queue=0/0 Enable-
Capabilities: [70] Express Unknown type IRQ 0
(only the stanza for the sound card, yell if you need more), and /proc/asound/card0/codec#0 gives:
Codec: Generic 14f1 ID 5045
Address: 0
Vendor Id: 0x14f15045
Subsystem Id: 0x173410cb
Revision Id: 0x100100
Default PCM: rates 0x140, bits 0x0e, types 0x1 Default Amp-In caps: N/A
Default Amp-Out caps: N/A
Node 0x10 [Pin Complex] wcaps 0x40058d: Stereo Amp-Out
Amp-Out caps: ofs=0x2b, nsteps=0x2b, stepsize=0x05, mute=1 Amp-Out vals: [0x28 0x28]
Pincap 0x0810014: OUT EAPD Detect
Pin Default 0x92170110: [Fixed] Speaker at Int Front
Conn = Analog, Color = Unknown
Pin-ctls: 0x40: OUT
Power: 0x0
Connection: 2
0x19* 0x17
Node 0x11 [Pin Complex] wcaps 0x40058d: Stereo Amp-Out
Amp-Out caps: ofs=0x2b, nsteps=0x2b, stepsize=0x05, mute=1 Amp-Out vals: [0x00 0x00]
Pincap 0x08113c: IN OUT HP Detect
Pin Default 0x0121401f: [Jack] HP Out at Ext Rear
Conn = 1/8, Color = Green
Pin-ctls: 0xc0: OUT HP
Power: 0x0
Connection: 2
0x19* 0x17
Node 0x12 [Pin Complex] wcaps 0x40058d: Stereo Amp-Out
Amp-Out caps: ofs=0x2b, nsteps=0x2b, stepsize=0x05, mute=1 Amp-Out vals: [0xab 0xab]
Pincap 0x08113c: IN OUT HP Detect
Pin Default 0x01a19020: [Jack] Mic at Ext Rear
Conn = 1/8, Color = Pink
Pin-ctls: 0x20: IN
Power: 0x0
Connection: 2
0x19* 0x17
Node 0x13 [Pin Complex] wcaps 0x400301: Stereo Digital
Pincap 0x0810: OUT
Pin Default 0x214571f0: [Jack] SPDIF Out at Sep Rear
Conn = Optical, Color = Yellow
Pin-ctls: 0x00:
Connection: 1
0x18
Node 0x14 [Pin Complex] wcaps 0x400081: Stereo
Pincap 0x081124: IN Detect
Pin Default 0x97a7012e: [Fixed] Mic at Int Riser
Conn = Analog, Color = Unknown
Pin-ctls: 0x20: IN
Node 0x15 [Pin Complex] wcaps 0x400001: Stereo
Pincap 0x0820: IN
Pin Default 0x400001f0: [N/A] Line Out at Ext N/A
Conn = Unknown, Color = Unknown
Pin-ctls: 0x00:
Node 0x16 [Beep Generator Widget] wcaps 0x70000c: Mono Amp-Out
Amp-Out caps: ofs=0x07, nsteps=0x07, stepsize=0x0b, mute=1 Amp-Out vals: [0x06]
Node 0x17 [Audio Mixer] wcaps 0x20050b: Stereo Amp-In
Amp-In caps: ofs=0x14, nsteps=0x2b, stepsize=0x05, mute=1 Amp-In vals: [0x94 0x94] [0x17 0x17] [0x94 0x94] [0x94 0x94] [0x94 0x94]
Power: 0x0
Connection: 5
0x19 0x14 0x12 0x11 0x15
Node 0x18 [Audio Output] wcaps 0x211: Stereo Digital
PCM: rates 0x040, bits 0x06, types 0x5
Node 0x19 [Audio Output] wcaps 0xc11: Stereo
PCM: rates 0x540, bits 0x0e, types 0x1
Power: 0x0
Node 0x1a [Audio Input] wcaps 0x100d0b: Stereo Amp-In
Amp-In caps: ofs=0x00, nsteps=0x17, stepsize=0x05, mute=1 Amp-In vals: [0x17 0x17] [0x00 0x00] [0x00 0x00] [0x00 0x00] [0x00 0x00]
Power: 0x0
Connection: 5
0x17 0x14 0x12 0x11 0x15*
Node 0x1b [Vendor Defined Widget] wcaps 0xf00000: Mono
please tell me if there is anything i can do, any additional information you need, or any general tipps.
thanks robert
Signature · 1 line
Robert Lemmen http://www.semistable.com
At Thu, 14 Jun 2007 10:31:56 +0200,
Quoted 18 lines · Robert Lemmen
hi everyone,
i have a fujitsu siemens amilo pro v3515 notebook, with a via VT8251/ VT8237A chipset. sound works fine through the speakers, but i don't get anything through the headphones, no headphone channel shows up in the mixer, and the headphone jack switch doesn't mute the speakers. i have alsa 1.0.13, and a 2.6.18 kernel. i tried all "model" settings that i could find in ALSA-Configuration in the kernel tree. lspci -nv gives
04:01.0 0403: 1106:3288 (rev 10)
Subsystem: 1734:10cb
Flags: bus master, fast devsel, latency 0, IRQ 58
Memory atc9100000(64-bit, non-prefetchable) [size=16K]
Capabilities: [50] Power Management version 2
Capabilities: [60] Message Signalled Interrupts: Mask- 64bit+ Queue=0/0 Enable-
Capabilities: [70] Express Unknown type IRQ 0
Quoted 3 lines
(only the stanza for the sound card, yell if you need more), and /proc/asound/card0/codec#0 gives:
Codec: Generic 14f1 ID 5045
The conexant codec is much better supported on ALSA 1.0.14. Give it a try first.
Takashi
Quoted 2 lines · Takashi Iwai
The conexant codec is much better supported on ALSA 1.0.14. Give it a try first.
and i thought my alsa version was recent :P
this did the trick in combination with model=laptop, other models didn't work. thanks for the help, and if there is any additional information you need in order to make the driver autodetect the model in future versions (if such a thing is possible), just tell me.
thanks again robert
Signature · 1 line
Robert Lemmen http://www.semistable.com
This patch should take care of your system.
Summary: hda-codec: Add Fujitsu Siemens v3515 support to patch_conexant.
This patch adds support for the Fujitsu Seimens Amilo Pro v3515 notebook.
Signed off by: Tobin Davis <[email protected]>
Quoted 13 lines · Robert Lemmen
Quoted 2 lines · Takashi Iwai
The conexant codec is much better supported on ALSA 1.0.14. Give it a try first.
and i thought my alsa version was recent :P
this did the trick in combination with model=laptop, other models didn't work. thanks for the help, and if there is any additional information you need in order to make the driver autodetect the model in future versions (if such a thing is possible), just tell me.
thanks again robert
Signature · 1 line
Tobin Davis <[email protected]>
pci/hda/patch_conexant.c +1 -0
@@ -802,6 +802,7 @@ static struct snd_pci_quirk cxt5045_cfg_SND_PCI_QUIRK (0x103c ,0x30b5 ,"HP DV2120" ,CXT5045_LAPTOP ),SND_PCI_QUIRK (0x103c ,0x30cd ,"HP DV Series" ,CXT5045_LAPTOP ),SND_PCI_QUIRK (0x1734 ,0x10ad ,"Fujitsu Si1520" ,CXT5045_FUJITSU ), +SND_PCI_QUIRK (0x1734 ,0x10cb ,"Fujitsu Si3515" ,CXT5045_FUJITSU ), SND_PCI_QUIRK(0x8086, 0x2111, "Conexant Reference board", CXT5045_LAPTOP), {} };
_______________________________________________
Alsa-devel mailing list
[email protected]
http://mailman.alsa-project.org/mailman/listinfo/alsa-devel
Takashi Iwai
AppliedAt Thu, 14 Jun 2007 19:26:14 -0700,
Quoted 8 lines · Tobin Davis
This patch should take care of your system.
Summary: hda-codec: Add Fujitsu Siemens v3515 support to
patch_conexant.This patch adds support for the Fujitsu Seimens Amilo Pro v3515 notebook.
Signed off by: Tobin Davis <[email protected]>
Applied to HG tree. Thanks.
Takashi
Quoted 5 lines · Takashi Iwai
Quoted 3 lines
This patch adds support for the Fujitsu Seimens Amilo Pro v3515 notebook.
Signed off by: Tobin Davis <[email protected]>
Applied to HG tree. Thanks.
perhaps you want to hold it for a while. i tried the patch on my machine, and it does change the behaviour a bit (when i plug in headphones both the headphones and the loudspeakers work, before only the loudspeakers did), but it does not mute the speakers. model=laptop fixes this. i wasn't 100% sure that i did apply the patch correctly and did not by accident use the old module, so i didn't report it immediately. didn't have time to look into it yet, but promise to do so soonish
cu robert
Signature · 1 line
Robert Lemmen http://www.semistable.com
At Tue, 19 Jun 2007 13:35:25 +0200,
Quoted 8 lines · Robert Lemmen
Quoted 5 lines · Takashi Iwai
Quoted 3 lines
This patch adds support for the Fujitsu Seimens Amilo Pro v3515 notebook.
Signed off by: Tobin Davis <[email protected]>
Applied to HG tree. Thanks.
Quoted 8 lines
perhaps you want to hold it for a while. i tried the patch on my machine, and it does change the behaviour a bit (when i plug in headphones both the headphones and the loudspeakers work, before only the loudspeakers did), but it does not mute the speakers. model=laptop fixes this. i wasn't 100% sure that i did apply the patch correctly and did not by accident use the old module, so i didn't report it immediately. didn't have time to look into it yet, but promise to do so soonish
The patch works as if model=fujitsu. So I suppose model=fujitsu doesn't work as expected?
Try to replace CXT5045_FUJITSU with CXT5045_LAPTOP in that patch.
Takashi
Quoted 4 lines · Takashi Iwai
The patch works as if model=fujitsu. So I suppose model=fujitsu doesn't work as expected?
Try to replace
CXT5045_FUJITSUwithCXT5045_LAPTOPin that patch.
hi everyone,
i am sorry, but this still doesn't work. if i pass model=laptop on the modprobe line or through /etc/modultils.d/, everything works as expected, including speaker muting on headphone jack insert. using no param or fujitsu works, but without muting. perhaps the driver somehow does not pick up the automatic model setting? is there a way to query a running driver on which model it did select? or is there a way to add something like a printf() to an alsa module (just for debugging)? and
lastly: i have no idea how all this stuff works, but looking at the patch, it looks like you are tying the lspci subsystem id to the model. in my lspci output i have multiple devices with that subsystem id (1734:10cb), could that be a problem? full lspci -vn output:
00:00.0 0600: 1106:0364
Subsystem: 1106:0364
Flags: medium devsel
Memory at c0000000 (32-bit, prefetchable) [disabled] [size=128M]
Capabilities: <access denied>
00:00.1 0600: 1106:1364
Flags: bus master, medium devsel, latency 0
00:00.2 0600: 1106:2364
Flags: bus master, medium devsel, latency 0
00:00.3 0600: 1106:3364
Flags: bus master, medium devsel, latency 0
00:00.4 0600: 1106:4364
Flags: bus master, medium devsel, latency 0
00:00.5 0800: 1106:5364 (prog-if 20 [IO(X)-APIC])
Flags: bus master, fast devsel, latency 0
00:00.6 0600: 1106:6364
Flags: bus master, fast devsel, latency 0
00:00.7 0600: 1106:7364
Flags: bus master, medium devsel, latency 0
00:01.0 0604: 1106:b198 (prog-if 00 [Normal decode])
Flags: bus master, 66MHz, medium devsel, latency 0
Bus: primary=00, secondary=01, subordinate=01, sec-latency=0 Memory behind bridge: c8000000-c8ffffff Prefetchable memory behind bridge: a0000000-bfffffff
Capabilities: <access denied>
00:02.0 0604: 1106:a364 (rev 80) (prog-if 00 [Normal decode])
Flags: bus master, fast devsel, latency 0
Bus: primary=00, secondary=02, subordinate=02, sec-latency=0
Capabilities: <access denied>
00:03.0 0604: 1106:c364 (rev 80) (prog-if 00 [Normal decode])
Flags: bus master, fast devsel, latency 0
Bus: primary=00, secondary=03, subordinate=03, sec-latency=0
I/O behind bridge: 00007000-00007fff
Memory behind bridge: c9000000-c90fffff
Capabilities: <access denied>00:0f.0 0101: 1106:0591 (rev 80) (prog-if 8f [Master SecP SecO PriP PriO])
Subsystem: 1734:10cb
Flags: bus master, medium devsel, latency 64, IRQ 217
I/O ports at 60b8 [size=8]
I/O ports at 60b0 [size=4]
I/O ports at 6008 [size=8]
I/O ports at 6004 [size=4]
I/O ports at 6010 [size=16]
I/O ports at 6400 [size=256]
Capabilities: <access denied>00:0f.1 0101: 1106:0571 (rev 07) (prog-if 8a [Master SecP PriP])
Subsystem: 1734:10cb
Flags: bus master, medium devsel, latency 0 I/O ports at 60a0 [size=16]
Capabilities: <access denied>
00:10.0 0c03: 1106:3038 (rev a0) (prog-if 00 [UHCI])
Subsystem: 1734:10cb
Flags: bus master, medium devsel, latency 64, IRQ 233 I/O ports at 6020 [size=32]
Capabilities: <access denied>
00:10.1 0c03: 1106:3038 (rev a0) (prog-if 00 [UHCI])
Subsystem: 1734:10cb
Flags: bus master, medium devsel, latency 64, IRQ 50 I/O ports at 6040 [size=32]
Capabilities: <access denied>
00:10.2 0c03: 1106:3038 (rev a0) (prog-if 00 [UHCI])
Subsystem: 1734:10cb
Flags: bus master, medium devsel, latency 64, IRQ 217 I/O ports at 6060 [size=32]
Capabilities: <access denied>
00:10.3 0c03: 1106:3038 (rev a0) (prog-if 00 [UHCI])
Subsystem: 1734:10cb
Flags: bus master, medium devsel, latency 64, IRQ 225 I/O ports at 6080 [size=32]
Capabilities: <access denied>
00:10.4 0c03: 1106:3104 (rev 86) (prog-if 20 [EHCI])
Subsystem: 1734:10cb
Flags: bus master, medium devsel, latency 64, IRQ 217 Memory at c9400000 (32-bit, non-prefetchable) [size=256]
Capabilities: <access denied>
00:11.0 0601: 1106:3337
Subsystem: 1734:10cb
Flags: medium devsel
Capabilities: <access denied>
00:11.7 0600: 1106:287e
Subsystem: 1106:337e
Flags: medium devsel
Capabilities: <access denied>
00:12.0 0200: 1106:3065 (rev 7c)
Subsystem: 1734:10cb
Flags: bus master, medium devsel, latency 24, IRQ 225
I/O ports at 6800 [size=256]
Memory at c9400400 (32-bit, non-prefetchable) [size=256]
Capabilities: <access denied>00:13.0 0604: 1106:337b (prog-if 00 [Normal decode])
Flags: bus master, fast devsel, latency 0
Bus: primary=00, secondary=04, subordinate=04, sec-latency=0 Memory behind bridge: c9100000-c91fffff
Capabilities: <access denied>
00:13.1 0604: 1106:337a (prog-if 01 [Subtractive decode])
Flags: bus master, fast devsel, latency 0
Bus: primary=00, secondary=05, subordinate=05, sec-latency=0 Memory behind bridge: 50000000-500fffff
Capabilities: <access denied>
01:00.0 0300: 1106:3371 (rev 01) (prog-if 00 [VGA])
Subsystem: 1734:10cb
Flags: bus master, 66MHz, medium devsel, latency 16, IRQ 9
Memory at a0000000 (32-bit, prefetchable) [size=512M]
Memory at c8000000 (32-bit, non-prefetchable) [size=16M]
Capabilities: <access denied>04:01.0 0403: 1106:3288 (rev 10)
Subsystem: 1734:10cb
Flags: bus master, fast devsel, latency 0, IRQ 58 Memory at c9100000 (64-bit, non-prefetchable) [size=16K]
Capabilities: <access denied>
05:01.0 0200: 168c:001a (rev 01)
Subsystem: 168c:2052
Flags: bus master, medium devsel, latency 80, IRQ 10 Memory at 50000000 (32-bit, non-prefetchable) [size=64K]
Capabilities: <access denied>
cu robert
Signature · 1 line
Robert Lemmen http://www.semistable.com
At Wed, 20 Jun 2007 21:02:40 +0200,
Quoted 10 lines · Robert Lemmen
Quoted 4 lines · Takashi Iwai
The patch works as if model=fujitsu. So I suppose model=fujitsu doesn't work as expected?
Try to replace
CXT5045_FUJITSUwithCXT5045_LAPTOPin that patch.hi everyone,
i am sorry, but this still doesn't work.
Are you sure that you remove model option with that patch? The model option overrides the default model preset.
Quoted 7 lines
if i pass model=laptop on the
modprobe line or through/etc/modultils.d/, everything works as expected, including speaker muting on headphone jack insert. using no param or fujitsu works, but without muting. perhaps the driver somehow does not pick up the automatic model setting? is there a way to query a running driver on which model it did select? or is there a way to add something like aprintf()to an alsa module (just for debugging)?
Add printk().
Quoted 5 lines
and
lastly: i have no idea how all this stuff works, but looking at the patch, it looks like you are tying the lspci subsystem id to the model. in my lspci output i have multiple devices with that subsystem id (1734:10cb), could that be a problem?
No, it looks OK.
Takashi
Quoted 4 lines · Takashi Iwai
Quoted 1 line
i am sorry, but this still doesn't work.
Are you sure that you remove model option with that patch? The model option overrides the default model preset.
sorry for the confusion, but the second patch i got here (the one where the model is set to "laptop" in the quirks stuff), actually *does* work fine. it seems it was a bit late for me, and i got confused with different versions of the modules under /lib/**.
cu robert
Signature · 1 line
Robert Lemmen http://www.semistable.com
Oops. The patch I sent you was based on a previous HG snapshot. I updated my tree and remade the patch. It just went out to the mailing list & Takashi for integration in the main tree.
Tobin
Quoted 13 lines · Robert Lemmen
Quoted 4 lines · Takashi Iwai
Quoted 1 line
i am sorry, but this still doesn't work.
Are you sure that you remove model option with that patch? The model option overrides the default model preset.
sorry for the confusion, but the second patch i got here (the one where the model is set to "laptop" in the quirks stuff), actually *does* work fine. it seems it was a bit late for me, and i got confused with different versions of the modules under
/lib/**.cu robert
Signature · 1 line
Tobin Davis <[email protected]>
At Thu, 21 Jun 2007 19:12:30 +0200,
Quoted 11 lines · Robert Lemmen
Quoted 4 lines · Takashi Iwai
Quoted 1 line
i am sorry, but this still doesn't work.
Are you sure that you remove model option with that patch? The model option overrides the default model preset.
sorry for the confusion, but the second patch i got here (the one where the model is set to "laptop" in the quirks stuff), actually *does* work fine. it seems it was a bit late for me, and i got confused with different versions of the modules under
/lib/**.
Do you mean the patch below (posted by Tobin)? If this really works for you, I'll merge it happily.
Takashi
pci/hda/patch_conexant.c +1 -1
@@ -802,7 +802,7 @@ static struct snd_pci_quirk cxt5045_cfg_SND_PCI_QUIRK (0x103c ,0x30b5 ,"HP DV2120" ,CXT5045_LAPTOP ),SND_PCI_QUIRK (0x103c ,0x30cd ,"HP DV Series" ,CXT5045_LAPTOP ),SND_PCI_QUIRK (0x1734 ,0x10ad ,"Fujitsu Si1520" ,CXT5045_FUJITSU ), -SND_PCI_QUIRK (0x1734 ,0x10cb ,"Fujitsu Si3515" ,CXT5045_FUJITSU ), +SND_PCI_QUIRK (0x1734 ,0x10cb ,"Fujitsu Si3515" ,CXT5045_LAPTOP ), SND_PCI_QUIRK(0x8086, 0x2111, "Conexant Reference board", CXT5045_LAPTOP), {} };
hi takashi,
Quoted 7 lines · Takashi Iwai
Do you mean the patch below (posted by Tobin)? If this really works for you, I'll merge it happily. [...]
diff -rdeaa182aebd8pci/hda/patch_conexant.c
pci/hda/patch_conexant.c static struct snd_pci_quirk cxt5045_cfg_ · line 808
Quoted 8 lines
pci/hda/patch_conexant.c +1
-1@@ -802,7 +802,7 @@ static struct snd_pci_quirk cxt5045_cfg_SND_PCI_QUIRK (0x103c ,0x30b5 ,"HP DV2120" ,CXT5045_LAPTOP ),SND_PCI_QUIRK (0x103c ,0x30cd ,"HP DV Series" ,CXT5045_LAPTOP ),SND_PCI_QUIRK (0x1734 ,0x10ad ,"Fujitsu Si1520" ,CXT5045_FUJITSU ), -SND_PCI_QUIRK (0x1734 ,0x10cb ,"Fujitsu Si3515" ,CXT5045_FUJITSU ), +SND_PCI_QUIRK (0x1734 ,0x10cb ,"Fujitsu Si3515" ,CXT5045_LAPTOP ), SND_PCI_QUIRK(0x8086, 0x2111, "Conexant Reference board", CXT5045_LAPTOP), {} };
exactly, this works perfectly on my machine!
cu robert
Signature · 1 line
Robert Lemmen http://www.semistable.com
At Mon, 25 Jun 2007 10:07:44 +0200,
Quoted 13 lines · Robert Lemmen
hi takashi,
Quoted 9 lines · Takashi Iwai
Do you mean the patch below (posted by Tobin)? If this really works for you, I'll merge it happily. [...]
diff -rdeaa182aebd8pci/hda/patch_conexant.cpci/hda/patch_conexant.c +0
-0@@ -802,7 +802,7 @@ static struct snd_pci_quirk cxt5045_cfg_SND_PCI_QUIRK (0x103c ,0x30b5 ,"HP DV2120" ,CXT5045_LAPTOP ), SND_PCI_QUIRK(0x103c, 0x30cd, "HP DV Series", CXT5045_LAPTOP),
Quoted 8 lines
pci/hda/patch_conexant.c static struct snd_pci_quirk cxt5045_cfg_ · line 808
Quoted 6 lines
pci/hda/patch_conexant.c +1
-1SND_PCI_QUIRK (0x1734 ,0x10ad ,"Fujitsu Si1520" ,CXT5045_FUJITSU ), -SND_PCI_QUIRK (0x1734 ,0x10cb ,"Fujitsu Si3515" ,CXT5045_FUJITSU ), +SND_PCI_QUIRK (0x1734 ,0x10cb ,"Fujitsu Si3515" ,CXT5045_LAPTOP ), SND_PCI_QUIRK(0x8086, 0x2111, "Conexant Reference board", CXT5045_LAPTOP), {} };exactly, this works perfectly on my machine!
Thanks for confirmation. Now committed to HG tree.
Takashi