ping command
hi,
I m using custom board same as eval board MPC8272ADS board.
IP assigned for both ethernets are...
ifconfig eth1 192.168.33.135 up ifconfig eth1 netmask 255.255.248.0
route add default gw 192.168.32.47 eth1
ifconfig eth0 192.168.178.89 up ifconfig eth0netmask 255.255.255.0 route add default gw 192.168.178.47 eth0
but if i try for ping 192.168.33.135 command pails by the server of 178 series
similarly ping 192.168.178.89 command pails by the server of 33 series..
what is the problem..and whre i m going wrong..?
thanks in advance..
Nethra
Signature · 2 lines
View this message in context: http://www.nabble.com/ping-command-tf4141032.html#a11779249 Sent from the linuxppc-embedded mailing list archive at Nabble.com.
Nethra,
Quoted 15 lines · Nethra
hi,
I m using custom board same as eval board MPC8272ADS board.
IP assigned for both ethernets are...
ifconfig eth1 192.168.33.135 up ifconfig eth1 netmask 255.255.248.0route add default gw 192.168.32.47 eth1
ifconfig eth0 192.168.178.89 up ifconfig eth0netmask 255.255.255.0 route add default gw 192.168.178.47 eth0
Quoted 5 lines
but if i try for ping 192.168.33.135 command pails by the server of 178 series
similarly ping 192.168.178.89 command pails by the server of 33 series..what is the problem..and whre i m going wrong..?
What does your routing table show? (route -n). It wouldn't hurt to also post the output of ifconfig for both interfaces.
regards,
Ben
root@cashel:~# route -n
Kernel IP routing table
Destination Gateway Genmask Flags Metric Ref Use
Iface
192.168.178.0 0.0.0.0 255.255.255.0 U 0 0 0 eth0
192.168.32.0 0.0.0.0 255.255.248.0 U 0 0 0 eth1
0.0.0.0 192.168.32.47 0.0.0.0 UG 0 0 0 eth1
0.0.0.0 192.168.178.47 0.0.0.0 UG 0 0 0 eth0
root@cashel:~# ifconfig
eth0 Link encap:Ethernet HWaddr 00:13:72:FE:A9:02
inet addr:192.168.178.89 Bcast:192.168.178.255
Mask:255.255.255.0
inet6 addr: fe80::213:72ff:fefe:a902/64 Scope:Link
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:15665 errors:0 dropped:0 overruns:0 frame:0
TX packets:9285 errors:0 dropped:0 overruns:0 carrier:9019
collisions:0 txqueuelen:1000
RX bytes:12957285 (12.3 MiB) TX bytes:2720267 (2.5 MiB)
Base address:0x8400eth1 Link encap:Ethernet HWaddr 00:13:72:7E:A9:02
inet addr:192.168.33.135 Bcast:192.168.33.255 Mask:255.255.248.0
inet6 addr: fe80::213:72ff:fe7e:a902/64 Scope:Link
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:634 errors:0 dropped:0 overruns:0 frame:0
TX packets:84 errors:0 dropped:0 overruns:0 carrier:82
collisions:0 txqueuelen:1000
RX bytes:103558 (101.1 KiB) TX bytes:12832 (12.5 KiB)
Base address:0x8500lo Link encap:Local Loopback
inet6 addr: ::1/128 Scope:Host
UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0
RX bytes:0 (0.0 b) TX bytes:0 (0.0 b)
root@cashel:~#
Quoted 15 lines · Nethra
hi,
I m using custom board same as eval board MPC8272ADS board.
IP assigned for both ethernets are...
ifconfig eth1 192.168.33.135 up ifconfig eth1 netmask 255.255.248.0route add default gw 192.168.32.47 eth1
ifconfig eth0 192.168.178.89 up ifconfig eth0netmask 255.255.255.0 route add default gw 192.168.178.47 eth0
Quoted 5 lines
but if i try for ping 192.168.33.135 command pails by the server of 178 series
similarly ping 192.168.178.89 command pails by the server of 33 series..what is the problem..and whre i m going wrong..?
What does your routing table show? (route -n). It wouldn't hurt to also post the output of ifconfig for both interfaces.
regards,
Ben
_______________________________________________
Linuxppc-embedded mailing list
[email protected]
https://ozlabs.org/mailman/listinfo/linuxppc-embedded
Signature · 2 lines
View this message in context: http://www.nabble.com/ping-command-tf4141032.html#a11823845 Sent from the linuxppc-embedded mailing list archive at Nabble.com.