Legacy ISA registers/interrupts in PCI device tree node
Hi,
I wonder, if there is a recommended way to specify ISA register addresses and interrupts for a PCI device (unlike for a PCI2ISA bridge)? The device in question is the integrated IDE controller of the VIA686B southbridge, which works in compatible/legacy mode and thus uses interrupts 14 and 15 of the i8259 PIC. Should the fdt contain this information or should I hardcode the values in the platform setup code?
Thanks!
Regards,
Gerhard
Signature · 2 lines
GMX FreeMail: 1 GB Postfach, 5 E-Mail-Adressen, 10 Free SMS. Alle Infos und kostenlose Anmeldung: http://www.gmx.net/de/go/freemail
Gerhard,
You could do a LOT worse than check the Pegasos.
Signature · 2 lines
Matt Sealey <[email protected]> Genesi, Manager, Developer Relations
Quoted 14 lines · Gerhard Pircher
Hi,
I wonder, if there is a recommended way to specify ISA register addresses and interrupts for a PCI device (unlike for a PCI2ISA bridge)? The device in question is the integrated IDE controller of the VIA686B southbridge, which works in compatible/legacy mode and thus uses interrupts 14 and 15 of the i8259 PIC. Should the fdt contain this information or should I hardcode the values in the platform setup code?
Thanks!
Regards,
Gerhard
Quoted 1 line · Matt Sealey
You could do a LOT worse than check the Pegasos.
Yes, mimmicing the pegasos will probably work
Quoted 7 lines
Matt Sealey <[email protected]>
Genesi, Manager, Developer RelationsQuoted 3 lines · Gerhard Pircher
Hi,
I wonder, if there is a recommended way to specify ISA register
Quoted 9 lines
addresses
Quoted 2 lines
and interrupts for a PCI device (unlike for a PCI2ISA bridge)? The device in question is the integrated IDE controller of the
VIA686B
Quoted 1 line
southbridge, which works in compatible/legacy mode and thus uses
interrupts
Quoted 1 line
14 and 15 of the i8259 PIC. Should the fdt contain this information
or
Quoted 1 line
should I hardcode the values in the platform setup code?
You may need a fixup like pegasos does because that chip seems to use 14/15 even when in native mode, which is somewhat out of spec.
Cheers,
Ben.
Quoted 2 lines
I wonder, if there is a recommended way to specify ISA register addresses and interrupts for a PCI device (unlike for a PCI2ISA bridge)?
The PCI binding describes the required way to do this.
Quoted 3 lines
The device in question is the integrated IDE controller of the VIA686B southbridge, which works in compatible/legacy mode and thus uses interrupts 14 and 15 of the i8259 PIC. Should the fdt contain this information
Yes, it should, even if you don't use this in the Linux kernel yet.
Quoted 1 line
or should I hardcode the values in the platform setup code?
No.
Segher
-------- Original-Nachricht --------
Datum: Mon, 16 Jul 2007 14:40:48 +0200
Von: Segher Boessenkool <[email protected]>
An: Gerhard Pircher <[email protected]>
CC: [email protected]
Betreff: Re: Legacy ISA registers/interrupts in PCI device tree node
Quoted 5 lines
Quoted 3 lines
I wonder, if there is a recommended way to specify ISA register addresses and interrupts for a PCI device (unlike for a PCI2ISA bridge)?
The PCI binding describes the required way to do this.
Hmm, I must reread the PCI binding spec. It didn't seem to contain any information about this.
Quoted 2 lines
Yes, it should, even if you don't use this in the Linux kernel yet.
Well, I still have to wire up the IDE interrupts in the platform setup code, right?
Gerhard
Signature · 2 lines
Ist Ihr Browser Vista-kompatibel? Jetzt die neuesten Browser-Versionen downloaden: http://www.gmx.net/de/go/browser
Quoted 7 lines
Quoted 5 lines
Quoted 3 lines
I wonder, if there is a recommended way to specify ISA register addresses and interrupts for a PCI device (unlike for a PCI2ISA bridge)?
The PCI binding describes the required way to do this.
Hmm, I must reread the PCI binding spec. It didn't seem to contain any information about this.
You can describe address regions in "reg" that aren't corresponding to any PCI BAR. There is also a facility to describe subtractive decoding (though I don't think you need this).
Quoted 4 lines
Quoted 2 lines
Yes, it should, even if you don't use this in the Linux kernel yet.
Well, I still have to wire up the IDE interrupts in the platform setup code, right?
Sure, if you want those interrupts to work, anyway ;-)
Segher