FWDing packets from a physical interface to a virtual interface
Hi, :)
Here is the situation:
I have a machine with 2 NICs, assume eth0 (192.168.0.10) connected to my LAN, and eth1 (192.168.0.20) connected to Internet through a gateway. I also, have a virtual tap0 (TUN/TAP) interface (10.0.0.1) on this machine.
All that I want to do is simply, forwarding ALL traffic coming to eth0 from the LAN, into my tap0 interface, So I can modify them using my own user space program which can capture packets on the tap interface and send them on eth1 to another address somewhere in the world (through Internet).
Since I want IP addresses unchanged, I cannot use NAT or Masquerading. As far as I know, In this matter forwarding should be done in Layer-2 so I'm not sure if I can use iptables to do the job.
I also have tried bridging but I was trapped in a horrible bridge loop (Enabling STP on bridge also didn't work for me).
Any ideas? :)
Thanks,
Arash
Arash:
AFAIK, you must open a path in the firewall to the vpn daemon (port/protocol) and the daemon will be in charge of administering the traffic between the clients and the vpn server.
Additionally, you must tell to the client where is the server (the ip address), what device will be used (tun or tap device).
May you want ask in the mailing list for the vendor/provider of the vpn software that you are using.
Hope this helps,
Jorge Dávila.
Quoted 21 lines · On Wed, 12 Sep 2007 02:06:53 +0330 Arash Yadegarnia <[email protected]> wrote:
Hi, :)
Here is the situation:
I have a machine with 2 NICs, assume eth0 (192.168.0.10) connected to my LAN, and eth1 (192.168.0.20) connected to Internet through a gateway. I also, have a virtual tap0 (TUN/TAP) interface (10.0.0.1) on this machine.
All that I want to do is simply, forwarding ALL traffic coming to eth0 from the LAN, into my tap0 interface, So I can modify them using my own user space program which can capture packets on the tap interface and send them on eth1 to another address somewhere in the world (through Internet).
Since I want IP addresses unchanged, I cannot use NAT or Masquerading. As far as I know, In this matter forwarding should be done in Layer-2 so I'm not sure if I can use iptables to do the job.
I also have tried bridging but I was trapped in a horrible bridge loop (Enabling STP on bridge also didn't work for me).
Quoted 7 lines
Any ideas? :)
Thanks,
Arash
Jorge Isaac Davila Lopez
Nicaragua Open Source
+505 430 5462
[email protected]
Thanks Jorge,
I'm not using any specific VPN solution, Me and my colleagues are developing a secure VPN solution based on kernel TUN/TAP driver. Since we have full control over our tap interface we just need to redirect the whole traffic coming into the eth0 (from a LAN) into the tap interface, so we can read them (I mean Ethernet frames in Layer 2) and send them out from the other pysical interface (eth1). BTW, Redirecting a single or even multiple ports won't work in my situation, because I want whole traffic in layer 2, not a specific port number.
Thanks,
Arash
Quoted 53 lines · Jorge Davila
Arash:
AFAIK, you must open a path in the firewall to the vpn daemon (port/protocol) and the daemon will be in charge of administering the traffic between the clients and the vpn server.
Additionally, you must tell to the client where is the server (the ip address), what device will be used (tun or tap device).
May you want ask in the mailing list for the vendor/provider of the vpn software that you are using.
Hope this helps,
Jorge Dávila.
Quoted 21 lines · On Wed, 12 Sep 2007 02:06:53 +0330 Arash Yadegarnia <[email protected]> wrote:
Hi, :)
Here is the situation:
I have a machine with 2 NICs, assume eth0 (192.168.0.10) connected to my LAN, and eth1 (192.168.0.20) connected to Internet through a gateway. I also, have a virtual tap0 (TUN/TAP) interface (10.0.0.1) on this machine.
All that I want to do is simply, forwarding ALL traffic coming to eth0 from the LAN, into my tap0 interface, So I can modify them using my own user space program which can capture packets on the tap interface and send them on eth1 to another address somewhere in the world (through Internet).
Since I want IP addresses unchanged, I cannot use NAT or Masquerading. As far as I know, In this matter forwarding should be done in Layer-2 so I'm not sure if I can use iptables to do the job.
I also have tried bridging but I was trapped in a horrible bridge loop (Enabling STP on bridge also didn't work for me).Quoted 7 lines
Any ideas? :)
Thanks,
ArashJorge Isaac Davila Lopez
Nicaragua Open Source
+505 430 5462
[email protected]
So maybe you'll have to some bridging stuff and not
netfilter/iptables ones ....
iptables/netfilter deals basically with Layer 3 (IP) packets and not
layer 2 frames, which are the ones you're interested.
Arash Yadegarnia escreveu:
Quoted 15 lines
Thanks Jorge,
I'm not using any specific VPN solution, Me and my colleagues are developing a secure VPN solution based on kernel TUN/TAP driver. Since we have full control over our tap interface we just need to redirect the whole traffic coming into the eth0 (from a LAN) into the tap interface, so we can read them (I mean Ethernet frames in Layer 2) and send them out from the other pysical interface (eth1). BTW, Redirecting a single or even multiple ports won't work in my situation, because I want whole traffic in layer 2, not a specific port number.
Thanks,
Arash
Signature · 8 lines
Atenciosamente / Sincerily, Leonardo Rodrigues Solutti Tecnologia http://www.solutti.com.br Minha armadilha de SPAM, NÃO mandem email [email protected] My SPAMTRAP, do not email it