2.6.23-rc6: known regressions v2
Subsystems (9)
A message that is not in the archive (sent off-list or not yet received): [email protected]
Hi all,
Here is a list of some known regressions in 2.6.23-rc6.
Feel free to add new regressions/remove fixed etc.
http://kernelnewbies.org/known_regressions
List of Aces
Name Regressions fixed since 21-Jun-2007
Adrian Bunk 10 Andi Kleen 7 Linus Torvalds 6 Alan Stern 5 Hugh Dickins 5 Trond Myklebust 5 Andrew Morton 4 David S. Miller 4 Al Viro 3 Alexey Starikovskiy 3 Cornelia Huck 3 Jens Axboe 3 Stephen Hemminger 3 Tejun Heo 3
Power management
Subject : powersaving degradation, (time spend in C0 goes up after a while)
References : http://lkml.org/lkml/2007/9/2/142
Last known good : ?
Submitter : Christian Leber <[email protected]>
Caused-By : ? Handled-By : ? Status : unknown
Subject : something broke resume from s2ram on mbp c1d (??? :))
References : http://lkml.org/lkml/2007/8/28/67
Last known good : 2.6.23-rc3
Submitter : Soeren Sonnenburg <[email protected]>
Caused-By : ? Handled-By : Rafael J. Wysocki <[email protected]> Status : unknown
Subject : 2.6.23-rc2 swsusp, suddenly increased uptime
References : http://lkml.org/lkml/2007/8/12/249
Last known good : ?
Submitter : Thomas Voegtle <[email protected]>
Caused-By : ? Handled-By : Rafael J. Wysocki <[email protected]> Status : problem is being debugged
Subject : resume from ram much slower
References : http://lkml.org/lkml/2007/8/10/275
Last known good : 2.6.23-rc1 ?
Submitter : Arkadiusz Miskiewicz <[email protected]>
Caused-By : ? Handled-By : Rafael J. Wysocki <[email protected]> Status : problem is being debugged
USB
Subject : usb 1-1: device not accepting address 2, error -62
References : http://lkml.org/lkml/2007/9/14/302
Last known good : ?
Submitter : Christian Volkmann <[email protected]>
Caused-By : ? Handled-By : ? Status : unknown
Farewell!
Michal
--
LOGOUT
http://www.stardust.webpages.pl/
Quoted 37 lines · Michal Piotrowski
Hi all,
Here is a list of some known regressions in 2.6.23-rc6.
Feel free to add new regressions/remove fixed etc.
http://kernelnewbies.org/known_regressionsList of Aces
Name Regressions fixed since 21-Jun-2007
Adrian Bunk 10 Andi Kleen 7 Linus Torvalds 6 Alan Stern 5 Hugh Dickins 5 Trond Myklebust 5 Andrew Morton 4 David S. Miller 4 Al Viro 3 Alexey Starikovskiy 3 Cornelia Huck 3 Jens Axboe 3 Stephen Hemminger 3 Tejun Heo 3Power management
Subject : powersaving degradation, (time spend in C0 goes up after a while)
References : http://lkml.org/lkml/2007/9/2/142
Last known good : ?
Submitter : Christian Leber <[email protected]>Caused-By : ? Handled-By : ? Status : unknown
Quoted 7 lines
Subject : something broke resume from s2ram on mbp c1d (??? :))
References : http://lkml.org/lkml/2007/8/28/67
Last known good : 2.6.23-rc3
Submitter : Soeren Sonnenburg <[email protected]>Caused-By : ? Handled-By : Rafael J. Wysocki <[email protected]> Status : unknown
Soeren said he would bisect, but I guess he didn't have the time.
Quoted 7 lines
Subject : 2.6.23-rc2 swsusp, suddenly increased uptime
References : http://lkml.org/lkml/2007/8/12/249
Last known good : ?
Submitter : Thomas Voegtle <[email protected]>Caused-By : ? Handled-By : Rafael J. Wysocki <[email protected]> Status : problem is being debugged
This is hard to reproduce, AFAICS, and unreproducible on any boxes I have access to.
Quoted 7 lines
Subject : resume from ram much slower
References : http://lkml.org/lkml/2007/8/10/275
Last known good : 2.6.23-rc1 ?
Submitter : Arkadiusz Miskiewicz <[email protected]>Caused-By : ? Handled-By : Rafael J. Wysocki <[email protected]> Status : problem is being debugged
Unresolved, bisection might be helpful.
Greetings,
Rafael
Quoted 11 lines · Rafael J. Wysocki
Quoted 7 lines · Michal Piotrowski
Subject : resume from ram much slower
References : http://lkml.org/lkml/2007/8/10/275
Last known good : 2.6.23-rc1 ?
Submitter : Arkadiusz Miskiewicz <[email protected]>Caused-By : ? Handled-By : Rafael J. Wysocki <[email protected]> Status : problem is being debuggedUnresolved, bisection might be helpful.
Took 16 hours of bisecting and playing with stuff.
It looks like the problematic patch is 18de5bc4c1f1f1fa5e14f354a7603bd6e9d4e3b6. bisection was hard and I'm 95% sure that this is the problematic patch. I'm currently using 2.6.23-rc6 with this reverted and so far resume works as it should.
commit 18de5bc4c1f1f1fa5e14f354a7603bd6e9d4e3b6
Author: Thomas Gleixner <[email protected]> Date: Sat Jul 21 04:37:34 2007 -0700
clockevents: fix resume logic
We need to make sure, that the clockevent devices are resumed, before the tick is resumed. The current resume logic does not guarantee this.
Add CLOCK_EVT_MODE_RESUME and call the set mode functions of the clock event devices before resuming the tick / oneshot functionality.
Fixup the existing users.
Thanks to Nigel Cunningham for tracking down a long standing thinko, which affected the jinxed VAIO.
arch/arm/mach-davinci/time.c +2 -0
@@ -285,6 +285,8 @@ static void davinci_set_mode(enum clock_event_mode mode,case CLOCK_EVT_MODE_SHUTDOWN : t->opts =TIMER_OPTS_DISABLED ;break ; +case CLOCK_EVT_MODE_RESUME : +break ; } }
arch/arm/mach-imx/time.c +1 -0
@@ -159,6 +159,7 @@ static void imx_set_mode(enum clock_event_mode mode, struct clock_event_device *break ;case CLOCK_EVT_MODE_SHUTDOWN :case CLOCK_EVT_MODE_UNUSED : +case CLOCK_EVT_MODE_RESUME :/* Left event sources disabled, no more interrupts appears */ break ; }
arch/arm/mach-ixp4xx/common.c +2 -0
@@ -459,6 +459,8 @@ static void ixp4xx_set_mode(enum clock_event_mode mode,default : osrt = opts =0 ;break ; +case CLOCK_EVT_MODE_RESUME : +break ; } *IXP4XX_OSRT1 = osrt | opts;
arch/arm/mach-omap1/time.c +1 -0
@@ -156,6 +156,7 @@ static void omap_mpu_set_mode(enum clock_event_mode mode,break ;case CLOCK_EVT_MODE_UNUSED :case CLOCK_EVT_MODE_SHUTDOWN : +case CLOCK_EVT_MODE_RESUME :break ; } }
arch/arm/plat-omap/timer32k.c +2 -0
@@ -156,6 +156,8 @@ static void omap_32k_timer_set_mode(enum clock_event_mode mode,case CLOCK_EVT_MODE_SHUTDOWN :omap_32k_timer_stop ();break ; +case CLOCK_EVT_MODE_RESUME : +break ; } }
arch/i386/kernel/apic.c +3 -0
@@ -263,6 +263,9 @@ static void lapic_timer_setup(enum clock_event_mode mode, v |= (APIC_LVT_MASKED |LOCAL_TIMER_VECTOR );apic_write_around (APIC_LVTT , v);break ; +case CLOCK_EVT_MODE_RESUME : +/* Nothing to do here */ +break ; }local_irq_restore (flags);
arch/i386/kernel/hpet.c +5 -66
92 lines not on this page · raw message
arch/i386/kernel/i8253.c +12 -14
@@ -3,11 +3,11 @@* */ #include <linux/clockchips.h> -#include <linux/spinlock.h> +#include <linux/init.h> +#include <linux/interrupt.h> #include <linux/jiffies.h> -#include <linux/sysdev.h> #include <linux/module.h> -#include <linux/init.h> +#include <linux/spinlock.h> #include <asm/smp.h> #include <asm/delay.h>
@@ -41,26 +41,24 @@ static void init_pit_timer(enum clock_event_mode mode,case CLOCK_EVT_MODE_PERIODIC :/* binary, mode 2, LSB/MSB, ch 0 */ outb_p (0x34 ,PIT_MODE ); -udelay (10 );outb_p (LATCH &0xff ,PIT_CH0 );/* LSB */ -udelay (10 );outb (LATCH >>8 ,PIT_CH0 );/* MSB */ break ; -/* -* Avoid unnecessary state transitions, as it confuses -* Geode / Cyrix based boxen. -*/ case CLOCK_EVT_MODE_SHUTDOWN : -if (evt->mode ==CLOCK_EVT_MODE_UNUSED ) -break ;case CLOCK_EVT_MODE_UNUSED : -if (evt->mode ==CLOCK_EVT_MODE_SHUTDOWN ) -break ; +outb_p (0x30 ,PIT_MODE ); +outb_p (0 ,PIT_CH0 );/* LSB */ +outb_p (0 ,PIT_CH0 );/* MSB */ +break ; +case CLOCK_EVT_MODE_ONESHOT :/* One shot setup */ outb_p (0x38 ,PIT_MODE ); -udelay (10 ); +break ; + +case CLOCK_EVT_MODE_RESUME : +/* Nothing to do here */ break ; }spin_unlock_irqrestore (&i8253_lock, flags);
arch/i386/kernel/vmiclock.c +1 -0
@@ -142,6 +142,7 @@ static void vmi_timer_set_mode(enum clock_event_mode mode,switch (mode) {case CLOCK_EVT_MODE_ONESHOT : +case CLOCK_EVT_MODE_RESUME :break ;case CLOCK_EVT_MODE_PERIODIC : cycles_per_hz = vmi_timer_ops.get_cycle_frequency ();
arch/i386/xen/time.c +3 -0
@@ -412,6 +412,7 @@ static void xen_timerop_set_mode(enum clock_event_mode mode,break ;case CLOCK_EVT_MODE_ONESHOT : +case CLOCK_EVT_MODE_RESUME :break ;case CLOCK_EVT_MODE_UNUSED :
@@ -474,6 +475,8 @@ static void xen_vcpuop_set_mode(enum clock_event_mode mode, HYPERVISOR_vcpu_op(VCPUOP_stop_periodic_timer, cpu, NULL))BUG ();break ; +case CLOCK_EVT_MODE_RESUME : +break ; } }
arch/sh/kernel/timers/timer-tmu.c +1 -0
@@ -80,6 +80,7 @@ static void tmu_set_mode(enum clock_event_mode mode,break ;case CLOCK_EVT_MODE_UNUSED :case CLOCK_EVT_MODE_SHUTDOWN : +case CLOCK_EVT_MODE_RESUME :break ; } }
arch/sparc64/kernel/time.c +1 -0
@@ -931,6 +931,7 @@ static void sparc64_timer_setup(enum clock_event_mode mode, {switch (mode) {case CLOCK_EVT_MODE_ONESHOT : +case CLOCK_EVT_MODE_RESUME :break ;case CLOCK_EVT_MODE_SHUTDOWN :
drivers/lguest/lguest.c +2 -0
@@ -398,6 +398,8 @@ static void lguest_clockevent_set_mode(enum clock_event_mode mode,break ;case CLOCK_EVT_MODE_PERIODIC :BUG (); +case CLOCK_EVT_MODE_RESUME : +break ; } }
include/linux/clockchips.h +1 -0
@@ -23,6 +23,7 @@ enum clock_event_mode {CLOCK_EVT_MODE_SHUTDOWN ,CLOCK_EVT_MODE_PERIODIC ,CLOCK_EVT_MODE_ONESHOT , + CLOCK_EVT_MODE_RESUME, };/* Clock event notification values */
kernel/time/tick-broadcast.c +4 -2
@@ -49,7 +49,7 @@ cpumask_t *tick_get_broadcast_mask(void)*/ static void tick_broadcast_start_periodic (struct clock_event_device *bc) { -if (bc && bc->mode ==CLOCK_EVT_MODE_SHUTDOWN ) +if (bc)tick_setup_periodic (bc,1 ); }
@@ -299,7 +299,7 @@ void tick_suspend_broadcast(void)spin_lock_irqsave (&tick_broadcast_lock, flags); bc = tick_broadcast_device.evtdev; -if (bc && tick_broadcast_device.mode ==TICKDEV_MODE_PERIODIC ) +if (bc)clockevents_set_mode (bc,CLOCK_EVT_MODE_SHUTDOWN );spin_unlock_irqrestore (&tick_broadcast_lock, flags);
@@ -316,6 +316,8 @@ int tick_resume_broadcast(void) bc = tick_broadcast_device.evtdev;if (bc) { +clockevents_set_mode (bc,CLOCK_EVT_MODE_RESUME ); +switch (tick_broadcast_device.mode) {case TICKDEV_MODE_PERIODIC :if (!cpus_empty (tick_broadcast_mask))
kernel/time/tick-common.c +10 -6
@@ -318,12 +318,17 @@ static void tick_resume(void) {struct tick_device *td = &__get_cpu_var (tick_cpu_device);unsigned long flags; +int broadcast =tick_resume_broadcast ();spin_lock_irqsave (&tick_device_lock, flags); -if (td->mode ==TICKDEV_MODE_PERIODIC ) -tick_setup_periodic (td->evtdev,0 ); -else -tick_resume_oneshot (); +clockevents_set_mode (td->evtdev,CLOCK_EVT_MODE_RESUME ); + +if (!broadcast) { +if (td->mode ==TICKDEV_MODE_PERIODIC ) +tick_setup_periodic (td->evtdev,0 ); +else +tick_resume_oneshot (); + }spin_unlock_irqrestore (&tick_device_lock, flags); }
@@ -360,8 +365,7 @@ static int tick_notify(struct notifier_block *nb, unsigned long reason,break ;case CLOCK_EVT_NOTIFY_RESUME : -if (!tick_resume_broadcast ()) -tick_resume (); +tick_resume ();break ;default :
Quoted 3 lines
Greetings,
Rafael
Signature · 2 lines
Arkadiusz Miśkiewicz PLD/Linux Team arekm / maven.pl http://ftp.pld-linux.org/
Quoted 11 lines · Rafael J. Wysocki
Quoted 7 lines · Michal Piotrowski
Subject : resume from ram much slower
References : http://lkml.org/lkml/2007/8/10/275
Last known good : 2.6.23-rc1 ?
Submitter : Arkadiusz Miskiewicz <[email protected]>Caused-By : ? Handled-By : Rafael J. Wysocki <[email protected]> Status : problem is being debuggedUnresolved, bisection might be helpful.
Took 16 hours of bisecting and playing with stuff.
It looks like the problematic patch is 18de5bc4c1f1f1fa5e14f354a7603bd6e9d4e3b6. bisection was hard and I'm 95% sure that this is the problematic patch. I'm currently using 2.6.23-rc6 with this reverted and so far resume works as it should.
commit 18de5bc4c1f1f1fa5e14f354a7603bd6e9d4e3b6
Author: Thomas Gleixner <[email protected]> Date: Sat Jul 21 04:37:34 2007 -0700
clockevents: fix resume logic
We need to make sure, that the clockevent devices are resumed, before the tick is resumed. The current resume logic does not guarantee this.
Add CLOCK_EVT_MODE_RESUME and call the set mode functions of the clock event devices before resuming the tick / oneshot functionality.
Fixup the existing users.
Thanks to Nigel Cunningham for tracking down a long standing thinko, which affected the jinxed VAIO.
arch/arm/mach-davinci/time.c +2 -0
@@ -285,6 +285,8 @@ static void davinci_set_mode(enum clock_event_mode mode,case CLOCK_EVT_MODE_SHUTDOWN : t->opts =TIMER_OPTS_DISABLED ;break ; +case CLOCK_EVT_MODE_RESUME : +break ; } }
arch/arm/mach-imx/time.c +1 -0
@@ -159,6 +159,7 @@ static void imx_set_mode(enum clock_event_mode mode, struct clock_event_device *break ;case CLOCK_EVT_MODE_SHUTDOWN :case CLOCK_EVT_MODE_UNUSED : +case CLOCK_EVT_MODE_RESUME :/* Left event sources disabled, no more interrupts appears */ break ; }
arch/arm/mach-ixp4xx/common.c +2 -0
@@ -459,6 +459,8 @@ static void ixp4xx_set_mode(enum clock_event_mode mode,default : osrt = opts =0 ;break ; +case CLOCK_EVT_MODE_RESUME : +break ; } *IXP4XX_OSRT1 = osrt | opts;
arch/arm/mach-omap1/time.c +1 -0
@@ -156,6 +156,7 @@ static void omap_mpu_set_mode(enum clock_event_mode mode,break ;case CLOCK_EVT_MODE_UNUSED :case CLOCK_EVT_MODE_SHUTDOWN : +case CLOCK_EVT_MODE_RESUME :break ; } }
arch/arm/plat-omap/timer32k.c +2 -0
@@ -156,6 +156,8 @@ static void omap_32k_timer_set_mode(enum clock_event_mode mode,case CLOCK_EVT_MODE_SHUTDOWN :omap_32k_timer_stop ();break ; +case CLOCK_EVT_MODE_RESUME : +break ; } }
arch/i386/kernel/apic.c +3 -0
@@ -263,6 +263,9 @@ static void lapic_timer_setup(enum clock_event_mode mode, v |= (APIC_LVT_MASKED |LOCAL_TIMER_VECTOR );apic_write_around (APIC_LVTT , v);break ; +case CLOCK_EVT_MODE_RESUME : +/* Nothing to do here */ +break ; }local_irq_restore (flags);
arch/i386/kernel/hpet.c +5 -66
92 lines not on this page · raw message
arch/i386/kernel/i8253.c +12 -14
@@ -3,11 +3,11 @@* */ #include <linux/clockchips.h> -#include <linux/spinlock.h> +#include <linux/init.h> +#include <linux/interrupt.h> #include <linux/jiffies.h> -#include <linux/sysdev.h> #include <linux/module.h> -#include <linux/init.h> +#include <linux/spinlock.h> #include <asm/smp.h> #include <asm/delay.h>
@@ -41,26 +41,24 @@ static void init_pit_timer(enum clock_event_mode mode,case CLOCK_EVT_MODE_PERIODIC :/* binary, mode 2, LSB/MSB, ch 0 */ outb_p (0x34 ,PIT_MODE ); -udelay (10 );outb_p (LATCH &0xff ,PIT_CH0 );/* LSB */ -udelay (10 );outb (LATCH >>8 ,PIT_CH0 );/* MSB */ break ; -/* -* Avoid unnecessary state transitions, as it confuses -* Geode / Cyrix based boxen. -*/ case CLOCK_EVT_MODE_SHUTDOWN : -if (evt->mode ==CLOCK_EVT_MODE_UNUSED ) -break ;case CLOCK_EVT_MODE_UNUSED : -if (evt->mode ==CLOCK_EVT_MODE_SHUTDOWN ) -break ; +outb_p (0x30 ,PIT_MODE ); +outb_p (0 ,PIT_CH0 );/* LSB */ +outb_p (0 ,PIT_CH0 );/* MSB */ +break ; +case CLOCK_EVT_MODE_ONESHOT :/* One shot setup */ outb_p (0x38 ,PIT_MODE ); -udelay (10 ); +break ; + +case CLOCK_EVT_MODE_RESUME : +/* Nothing to do here */ break ; }spin_unlock_irqrestore (&i8253_lock, flags);
arch/i386/kernel/vmiclock.c +1 -0
@@ -142,6 +142,7 @@ static void vmi_timer_set_mode(enum clock_event_mode mode,switch (mode) {case CLOCK_EVT_MODE_ONESHOT : +case CLOCK_EVT_MODE_RESUME :break ;case CLOCK_EVT_MODE_PERIODIC : cycles_per_hz = vmi_timer_ops.get_cycle_frequency ();
arch/i386/xen/time.c +3 -0
@@ -412,6 +412,7 @@ static void xen_timerop_set_mode(enum clock_event_mode mode,break ;case CLOCK_EVT_MODE_ONESHOT : +case CLOCK_EVT_MODE_RESUME :break ;case CLOCK_EVT_MODE_UNUSED :
@@ -474,6 +475,8 @@ static void xen_vcpuop_set_mode(enum clock_event_mode mode, HYPERVISOR_vcpu_op(VCPUOP_stop_periodic_timer, cpu, NULL))BUG ();break ; +case CLOCK_EVT_MODE_RESUME : +break ; } }
arch/sh/kernel/timers/timer-tmu.c +1 -0
@@ -80,6 +80,7 @@ static void tmu_set_mode(enum clock_event_mode mode,break ;case CLOCK_EVT_MODE_UNUSED :case CLOCK_EVT_MODE_SHUTDOWN : +case CLOCK_EVT_MODE_RESUME :break ; } }
arch/sparc64/kernel/time.c +1 -0
@@ -931,6 +931,7 @@ static void sparc64_timer_setup(enum clock_event_mode mode, {switch (mode) {case CLOCK_EVT_MODE_ONESHOT : +case CLOCK_EVT_MODE_RESUME :break ;case CLOCK_EVT_MODE_SHUTDOWN :
drivers/lguest/lguest.c +2 -0
@@ -398,6 +398,8 @@ static void lguest_clockevent_set_mode(enum clock_event_mode mode,break ;case CLOCK_EVT_MODE_PERIODIC :BUG (); +case CLOCK_EVT_MODE_RESUME : +break ; } }
include/linux/clockchips.h +1 -0
@@ -23,6 +23,7 @@ enum clock_event_mode {CLOCK_EVT_MODE_SHUTDOWN ,CLOCK_EVT_MODE_PERIODIC ,CLOCK_EVT_MODE_ONESHOT , + CLOCK_EVT_MODE_RESUME, };/* Clock event notification values */
kernel/time/tick-broadcast.c +4 -2
@@ -49,7 +49,7 @@ cpumask_t *tick_get_broadcast_mask(void)*/ static void tick_broadcast_start_periodic (struct clock_event_device *bc) { -if (bc && bc->mode ==CLOCK_EVT_MODE_SHUTDOWN ) +if (bc)tick_setup_periodic (bc,1 ); }
@@ -299,7 +299,7 @@ void tick_suspend_broadcast(void)spin_lock_irqsave (&tick_broadcast_lock, flags); bc = tick_broadcast_device.evtdev; -if (bc && tick_broadcast_device.mode ==TICKDEV_MODE_PERIODIC ) +if (bc)clockevents_set_mode (bc,CLOCK_EVT_MODE_SHUTDOWN );spin_unlock_irqrestore (&tick_broadcast_lock, flags);
@@ -316,6 +316,8 @@ int tick_resume_broadcast(void) bc = tick_broadcast_device.evtdev;if (bc) { +clockevents_set_mode (bc,CLOCK_EVT_MODE_RESUME ); +switch (tick_broadcast_device.mode) {case TICKDEV_MODE_PERIODIC :if (!cpus_empty (tick_broadcast_mask))
kernel/time/tick-common.c +10 -6
@@ -318,12 +318,17 @@ static void tick_resume(void) {struct tick_device *td = &__get_cpu_var (tick_cpu_device);unsigned long flags; +int broadcast =tick_resume_broadcast ();spin_lock_irqsave (&tick_device_lock, flags); -if (td->mode ==TICKDEV_MODE_PERIODIC ) -tick_setup_periodic (td->evtdev,0 ); -else -tick_resume_oneshot (); +clockevents_set_mode (td->evtdev,CLOCK_EVT_MODE_RESUME ); + +if (!broadcast) { +if (td->mode ==TICKDEV_MODE_PERIODIC ) +tick_setup_periodic (td->evtdev,0 ); +else +tick_resume_oneshot (); + }spin_unlock_irqrestore (&tick_device_lock, flags); }
@@ -360,8 +365,7 @@ static int tick_notify(struct notifier_block *nb, unsigned long reason,break ;case CLOCK_EVT_NOTIFY_RESUME : -if (!tick_resume_broadcast ()) -tick_resume (); +tick_resume ();break ;default :
Quoted 3 lines
Greetings,
Rafael
Signature · 2 lines
Arkadiusz Miśkiewicz PLD/Linux Team arekm / maven.pl http://ftp.pld-linux.org/
Quoted 20 lines · Arkadiusz Miskiewicz
Quoted 11 lines · Rafael J. Wysocki
Quoted 7 lines · Michal Piotrowski
Subject : resume from ram much slower
References : http://lkml.org/lkml/2007/8/10/275
Last known good : 2.6.23-rc1 ?
Submitter : Arkadiusz Miskiewicz <[email protected]>Caused-By : ? Handled-By : Rafael J. Wysocki <[email protected]> Status : problem is being debuggedUnresolved, bisection might be helpful.
Took 16 hours of bisecting and playing with stuff.
It looks like the problematic patch is
18de5bc4c1f1f1fa5e14f354a7603bd6e9d4e3b6. bisection was hard and I'm 95% sure that this is the problematic patch. I'm currently using 2.6.23-rc6 with this reverted and so far resume works as it should.
Quoted 5 lines
commit
18de5bc4c1f1f1fa5e14f354a7603bd6e9d4e3b6Author: Thomas Gleixner <[email protected]> Date: Sat Jul 21 04:37:34 2007 -0700clockevents: fix resume logic
Linus pulled a series of patches which are addressing this issue into his tree yesterday. Can you please retest against current git ?
tglx
Quoted 20 lines · Arkadiusz Miskiewicz
Quoted 11 lines · Rafael J. Wysocki
Quoted 7 lines · Michal Piotrowski
Subject : resume from ram much slower
References : http://lkml.org/lkml/2007/8/10/275
Last known good : 2.6.23-rc1 ?
Submitter : Arkadiusz Miskiewicz <[email protected]>Caused-By : ? Handled-By : Rafael J. Wysocki <[email protected]> Status : problem is being debuggedUnresolved, bisection might be helpful.
Took 16 hours of bisecting and playing with stuff.
It looks like the problematic patch is
18de5bc4c1f1f1fa5e14f354a7603bd6e9d4e3b6. bisection was hard and I'm 95% sure that this is the problematic patch. I'm currently using 2.6.23-rc6 with this reverted and so far resume works as it should.
Quoted 5 lines
commit
18de5bc4c1f1f1fa5e14f354a7603bd6e9d4e3b6Author: Thomas Gleixner <[email protected]> Date: Sat Jul 21 04:37:34 2007 -0700clockevents: fix resume logic
Linus pulled a series of patches which are addressing this issue into his tree yesterday. Can you please retest against current git ?
tglx
Quoted 21 lines · Thomas Gleixner
Quoted 20 lines · Arkadiusz Miskiewicz
Quoted 10 lines · Rafael J. Wysocki
Quoted 7 lines · Michal Piotrowski
Subject : resume from ram much slower
References : http://lkml.org/lkml/2007/8/10/275
Last known good : 2.6.23-rc1 ?
Submitter : Arkadiusz Miskiewicz <[email protected]>Caused-By : ? Handled-By : Rafael J. Wysocki <[email protected]> Status : problem is being debuggedUnresolved, bisection might be helpful.
Took 16 hours of bisecting and playing with stuff.
It looks like the problematic patch is
18de5bc4c1f1f1fa5e14f354a7603bd6e9d4e3b6. bisection was hard and I'm 95% sure that this is the problematic patch. I'm currently using 2.6.23-rc6 with this reverted and so far resume works as it should.
Quoted 8 lines
Quoted 5 lines
commit
18de5bc4c1f1f1fa5e14f354a7603bd6e9d4e3b6Author: Thomas Gleixner <[email protected]> Date: Sat Jul 21 04:37:34 2007 -0700clockevents: fix resume logic
Linus pulled a series of patches which are addressing this issue into his tree yesterday. Can you please retest against current git ?
Looks like the problem is fixed in current git for me. Thanks!
ps. The description about vaio not resuming without key pressing matches what I was seeing here on thinkpad z60m, too.
Quoted 1 line
tglx
Signature · 2 lines
Arkadiusz Miśkiewicz PLD/Linux Team arekm / maven.pl http://ftp.pld-linux.org/
Quoted 21 lines · Thomas Gleixner
Quoted 20 lines · Arkadiusz Miskiewicz
Quoted 10 lines · Rafael J. Wysocki
Quoted 7 lines · Michal Piotrowski
Subject : resume from ram much slower
References : http://lkml.org/lkml/2007/8/10/275
Last known good : 2.6.23-rc1 ?
Submitter : Arkadiusz Miskiewicz <[email protected]>Caused-By : ? Handled-By : Rafael J. Wysocki <[email protected]> Status : problem is being debuggedUnresolved, bisection might be helpful.
Took 16 hours of bisecting and playing with stuff.
It looks like the problematic patch is
18de5bc4c1f1f1fa5e14f354a7603bd6e9d4e3b6. bisection was hard and I'm 95% sure that this is the problematic patch. I'm currently using 2.6.23-rc6 with this reverted and so far resume works as it should.
Quoted 8 lines
Quoted 5 lines
commit
18de5bc4c1f1f1fa5e14f354a7603bd6e9d4e3b6Author: Thomas Gleixner <[email protected]> Date: Sat Jul 21 04:37:34 2007 -0700clockevents: fix resume logic
Linus pulled a series of patches which are addressing this issue into his tree yesterday. Can you please retest against current git ?
Looks like the problem is fixed in current git for me. Thanks!
ps. The description about vaio not resuming without key pressing matches what I was seeing here on thinkpad z60m, too.
Quoted 1 line
tglx
Signature · 2 lines
Arkadiusz Miśkiewicz PLD/Linux Team arekm / maven.pl http://ftp.pld-linux.org/
Quoted 6 lines · Arkadiusz Miskiewicz
Quoted 4 lines
Quoted 1 line
clockevents: fix resume logic
Linus pulled a series of patches which are addressing this issue into his tree yesterday. Can you please retest against current git ?
Looks like the problem is fixed in current git for me. Thanks!
Thanks for testing.
Quoted 2 lines
ps. The description about vaio not resuming without key pressing matches what I was seeing here on thinkpad z60m, too.
Sigh, there were several subtle reason why you would need to press keys during resume. The one you are referring to is the one which is the most obscure. It would be nice if you could revert that particular one and check whether it still works on your box.
tglx
Quoted 6 lines · Arkadiusz Miskiewicz
Quoted 4 lines
Quoted 1 line
clockevents: fix resume logic
Linus pulled a series of patches which are addressing this issue into his tree yesterday. Can you please retest against current git ?
Looks like the problem is fixed in current git for me. Thanks!
Thanks for testing.
Quoted 2 lines
ps. The description about vaio not resuming without key pressing matches what I was seeing here on thinkpad z60m, too.
Sigh, there were several subtle reason why you would need to press keys during resume. The one you are referring to is the one which is the most obscure. It would be nice if you could revert that particular one and check whether it still works on your box.
tglx
Quoted 9 lines · Thomas Gleixner
Quoted 6 lines · Arkadiusz Miskiewicz
Quoted 4 lines
Quoted 1 line
clockevents: fix resume logic
Linus pulled a series of patches which are addressing this issue into his tree yesterday. Can you please retest against current git ?
Looks like the problem is fixed in current git for me. Thanks!
Thanks for testing.
I can confirm that the problem is fixed for me too in current git when using the free avivo driver (with the binary only fglrx driver the machine just hangs on resume or even sometimes on sleep). So it might be worth to purposely keep that such that people transit from fglrx to the free avivo/radeonhd drivers. Anyway s2ram with avivo takes 2-3 sec to suspend and 4-5 for resume (when fglrx worked it was more in the 10-20 secs).
Soeren.
Signature · 2 lines
Sometimes, there's a moment as you're waking, when you become aware of the real world around you, but you're still dreaming.
Quoted 9 lines · Thomas Gleixner
Quoted 6 lines · Arkadiusz Miskiewicz
Quoted 4 lines
Quoted 1 line
clockevents: fix resume logic
Linus pulled a series of patches which are addressing this issue into his tree yesterday. Can you please retest against current git ?
Looks like the problem is fixed in current git for me. Thanks!
Thanks for testing.
I can confirm that the problem is fixed for me too in current git when using the free avivo driver (with the binary only fglrx driver the machine just hangs on resume or even sometimes on sleep). So it might be worth to purposely keep that such that people transit from fglrx to the free avivo/radeonhd drivers. Anyway s2ram with avivo takes 2-3 sec to suspend and 4-5 for resume (when fglrx worked it was more in the 10-20 secs).
Soeren.
Signature · 2 lines
Sometimes, there's a moment as you're waking, when you become aware of the real world around you, but you're still dreaming.
Quoted 37 lines · Michal Piotrowski
Hi all,
Here is a list of some known regressions in 2.6.23-rc6.
Feel free to add new regressions/remove fixed etc.
http://kernelnewbies.org/known_regressionsList of Aces
Name Regressions fixed since 21-Jun-2007
Adrian Bunk 10 Andi Kleen 7 Linus Torvalds 6 Alan Stern 5 Hugh Dickins 5 Trond Myklebust 5 Andrew Morton 4 David S. Miller 4 Al Viro 3 Alexey Starikovskiy 3 Cornelia Huck 3 Jens Axboe 3 Stephen Hemminger 3 Tejun Heo 3Power management
Subject : powersaving degradation, (time spend in C0 goes up after a while)
References : http://lkml.org/lkml/2007/9/2/142
Last known good : ?
Submitter : Christian Leber <[email protected]>Caused-By : ? Handled-By : ? Status : unknown
Quoted 7 lines
Subject : something broke resume from s2ram on mbp c1d (??? :))
References : http://lkml.org/lkml/2007/8/28/67
Last known good : 2.6.23-rc3
Submitter : Soeren Sonnenburg <[email protected]>Caused-By : ? Handled-By : Rafael J. Wysocki <[email protected]> Status : unknown
Soeren said he would bisect, but I guess he didn't have the time.
Quoted 7 lines
Subject : 2.6.23-rc2 swsusp, suddenly increased uptime
References : http://lkml.org/lkml/2007/8/12/249
Last known good : ?
Submitter : Thomas Voegtle <[email protected]>Caused-By : ? Handled-By : Rafael J. Wysocki <[email protected]> Status : problem is being debugged
This is hard to reproduce, AFAICS, and unreproducible on any boxes I have access to.
Quoted 7 lines
Subject : resume from ram much slower
References : http://lkml.org/lkml/2007/8/10/275
Last known good : 2.6.23-rc1 ?
Submitter : Arkadiusz Miskiewicz <[email protected]>Caused-By : ? Handled-By : Rafael J. Wysocki <[email protected]> Status : problem is being debugged
Unresolved, bisection might be helpful.
Greetings,
Rafael