Skip to contentSkip to conversation

--separate-channels issues

DISCUSSION hong zhang 2 participants 4 messages May 10, 2011

lore
Share & tools
lore

hong zhang

author
#0 lore raw

Takashi,

When I run following commands with 2 pins inputs.

$ arecord -f S16_LE -r 48000 -c 4 -D plughw:0,1 --separate-channels c1.wav c2.wav c3.wav c4.wav

hd c3.wav and c4.wav returns 0 but c1.wav and c2.wav got right data. Such as

$ hd c3.wav 
00000000  00 00 00 00 00 00 00 00  00 00 00 00 00 00 00 00  |................|
*
005ad000

Also, I see trigger Rx start command and then stop command immediately.

Any hint to look into?

Thanks.

---henry

#1 lore raw

At Tue, 10 May 2011 09:34:40 -0700 (PDT),

Quoted 5 lines · hong zhang

Takashi,

When I run following commands with 2 pins inputs.

Quoted 8 lines
$ arecord -f S16_LE -r 48000 -c 4 -D plughw:0,1 --separate-channels c1.wav c2.wav c3.wav c4.wav

hd c3.wav and c4.wav returns 0 but c1.wav and c2.wav got right data. Such as

$ hd c3.wav 
00000000  00 00 00 00 00 00 00 00  00 00 00 00 00 00 00 00  |................|
*
005ad000

Use hw:0,1 instead of plughw:0,1. If the hardware really supports the multi-channels, it should work in that way. I guess you didn't notice that the input is 2 channels because plughw covers it.

Quoted 1 line

Also, I see trigger Rx start command and then stop command immediately.

This sounds like a driver issue.

Takashi

author
#2 lore raw

Takashi,

If use hw:0,1, no "-c 4" is allowed. That is why I use plughw see following:

arecord -f S16_LE -r 48000 -c 4 -D hw:0,1 --separate-channels c1.wav c2.wav c3.wav c4.wav

Recording raw data 'c1.wav' : Signed 16 bit Little Endian, Rate 48000 Hz, Channels 4
arecord: set_params:1048: Access type not available

hw:0,1 works with no "-c" option only. I even try it on my laptop.

---henry

Quoted 39 lines · Takashi Iwai

From: Takashi Iwai <[email protected]>
Subject: Re: [alsa-devel] --separate-channels issues
To: "hong zhang" <[email protected]>
Cc: [email protected]
Date: Tuesday, May 10, 2011, 11:40 AM
At Tue, 10 May 2011 09:34:40 -0700
(PDT),

Quoted 6 lines · hong zhang

Takashi,

When I run following commands with 2 pins inputs.

$ arecord -f S16_LE -r 48000 -c 4 -D plughw:0,1

--separate-channels c1.wav c2.wav c3.wav c4.wav

Quoted 2 lines

hd c3.wav and c4.wav returns 0 but c1.wav and c2.wav

got right data.

Quoted 3 lines

Such as

$ hd c3.wav 
00000000  00 00 00 00 00 00 00 00  00 00 00

00 00 00 00 00  |................|

Quoted 2 lines

*
005ad000

Use hw:0,1 instead of plughw:0,1.  If the hardware really supports the
multi-channels, it should work in that way.  I guess you didn't notice
that the input is 2 channels because plughw covers it.

Quoted 1 line

Also, I see trigger Rx start command and then stop

command immediately.

This sounds like a driver issue.

Takashi

#3 lore raw

At Tue, 10 May 2011 11:21:19 -0700 (PDT),

Quoted 9 lines · hong zhang

Takashi,

If use hw:0,1, no "-c 4" is allowed. That is why I use plughw see following:

arecord -f S16_LE -r 48000 -c 4 -D hw:0,1 --separate-channels c1.wav c2.wav c3.wav c4.wav

Recording raw data 'c1.wav' : Signed 16 bit Little Endian, Rate 48000 Hz, Channels 4
arecord: set_params:1048: Access type not available

Ah, this is about non-interleaved mode.
Can you record the normal 4-channel WAV file without --separate-channels option at all, and does it contain the correct signals for all channels?

If you can record 4-channels interleaved format properly but the conversion via plughw doesn't give all channels, it's a bug in plug layer. Otherwise, it's a driver issue.

Takashi