Skip to contentSkip to conversation

Problems using quickcam_messenger on ARM (FYI)

DISCUSSION Markus Hirschmann 3 participants 4 messages Nov 6, 2007 – Nov 13, 2007

lore
Share & tools
lore
#0 lore raw

Hello Kernel-Developer,

Module quickcam_messenger seems to be broken (tried 2.6.18 and 2.6.22)
on 2 different NSLU2 (ARM). Picture is attached. Same kernel and module can be used without any problems on x86 here. I don't have any ARM device beside the NSLU2, so I cannot check.

The solution was to use Christian Magnusson's quickcam module. Everything worked without any problem. Webcam is:

Bus 003 Device 005: ID 046d:08f0 Logitech, Inc. QuickCam Messenger

Best regards and thanks for your work!

Markus

Kernel is:
Linux secure 2.6.18-5-ixp4xx #1 Thu Oct 11 20:42:54 UTC 2007 armv5tel GNU/Linux

Logs with quickcam_messenger:

Nov  5 13:35:54 secure kernel: Linux video capture interface: v2.00
Nov  5 13:35:54 secure kernel:
drivers/media/video/usbvideo/quickcam_messenger.c: Logitech Quickcam
Messenger USB v0.01
Nov  5 13:35:54 secure kernel: videodev: "QCM USB Camera" has no release
callback. Please fix your driver for proper sysfs support, see
http://lwn.net/Articles/36850/
Nov  5 13:35:54 secure kernel: drivers/media/video/usbvideo/usbvideo.c:
QCM on /dev/video0: canvas=320x240 videosize=320x240
Nov  5 13:35:55 secure kernel: input: QCM button as /class/input/input1
Nov  5 13:35:55 secure kernel: usbcore: registered new interface driver QCM
Nov  5 13:35:55 secure kernel: swapped image found
Nov  5 13:35:55 secure kernel: Image loaded to NPE-B Func:0, Rel: 2:1,
Status: 82c00000
Nov  5 13:35:55 secure kernel: usbcore: registered new interface driver

snd-usb-audio

Nov  5 13:36:13 secure motion: [0] Processing thread 0 - config file
/etc/motion/motion.conf
Nov  5 13:36:13 secure motion: [1] Thread is from /etc/motion/motion.conf
Nov  5 13:36:13 secure motion: [1] Thread started
Nov  5 13:36:13 secure motion: [1] Failed with YUV420P, trying YUV422
palette: Invalid argument
Nov  5 13:36:13 secure motion: [1] Failed with YUV422, trying RGB24
palette: Invalid argument
Nov  5 13:37:07 secure motion: [1] Motion terminating
Nov  5 13:37:07 secure kernel: drivers/media/video/usbvideo/usbvideo.c:
Packet Statistics: Total=54784. Empty=0. Usage=100%%
Nov  5 13:37:07 secure kernel: drivers/media/video/usbvideo/usbvideo.c:
Transfer Statistics: Transferred=41MB Usage=78%%
Nov  5 13:37:41 secure motion: [0] Processing thread 0 - config file
/etc/motion/motion.conf
Nov  5 13:37:41 secure motion: [1] Thread is from /etc/motion/motion.conf
Nov  5 13:37:41 secure motion: [1] Thread started
Nov  5 13:37:41 secure motion: [1] Failed with YUV420P, trying YUV422
palette: Invalid argument
Nov  5 13:37:41 secure motion: [1] Failed with YUV422, trying RGB24
palette: Invalid argument
Nov  5 13:37:46 secure motion: [1] sync error in proc 2011: Interrupted
system call
Nov  5 13:37:46 secure motion: [1] Motion terminating
Nov  5 13:37:46 secure kernel: drivers/media/video/usbvideo/usbvideo.c:
Packet Statistics: Total=5024. Empty=0. Usage=100%%
Nov  5 13:37:46 secure kernel: drivers/media/video/usbvideo/usbvideo.c:
Transfer Statistics: Transferred=3763KB Usage=74%%
Nov  5 13:38:09 secure kernel: usb 2-1: USB disconnect, address 2
Nov  5 13:38:09 secure kernel: drivers/media/video/usbvideo/usbvideo.c:

USB camera disconnected.

#1 lore raw

Em Ter, 2007-11-06 às 18:25 +0100, Markus Hirschmann escreveu:

Quoted 9 lines

Hello Kernel-Developer,

Module quickcam_messenger seems to be broken (tried 2.6.18 and 2.6.22) on 2 different NSLU2 (ARM). Picture is attached. Same kernel and module can be used without any problems on x86 here. I don't have any ARM device beside the NSLU2, so I cannot check.

The solution was to use Christian Magnusson's quickcam module. Everything worked without any problem. Webcam is:

Hmm... you're mentioning the quickcam module, but some of your logs are related to usbvideo driver.

On a quick glance, I didn't find anything that could explain your troubles. It seems to be related to a wrong order at the output format (for example, the driver is sending RGB, instead of BGR).

It may also be an issue at the userspace application that is using the wrong logic to deal with Big Endian.

Signature · 2 lines
Cheers,
Mauro
#2 lore raw

Hi Mauro,

Quoted 16 lines · Mauro Carvalho Chehab

Em Ter, 2007-11-06 às 18:25 +0100, Markus Hirschmann escreveu:

Quoted 10 lines

Hello Kernel-Developer,

Module quickcam_messenger seems to be broken (tried 2.6.18 and 2.6.22) on 2 different NSLU2 (ARM). Picture is attached. Same kernel and module can be used without any problems on x86 here. I don't have any ARM device beside the NSLU2, so I cannot check.

The solution was to use Christian Magnusson's quickcam module. Everything worked without any problem. Webcam is:

Hmm... you're mentioning the quickcam module, but some of your logs are related to usbvideo driver.

Quoted 8 lines

On a quick glance, I didn't find anything that could explain your troubles. It seems to be related to a wrong order at the output format (for example, the driver is sending RGB, instead of BGR).

It may also be an issue at the userspace application that is using the wrong logic to deal with Big Endian.

The NSLU2 is based on a IXP420 processor that can change its endianess. I suppose Markus has installed the debian-arm distribution on his NSLU2 so it is configured as little-endian.
Nevertheless, I took a look at the code of quickcam messenger that is in usbvideo/
This macro: RGB24_PUTPIXEL puts in memory the following bytes:

                *pf++ = (vb);
                *pf++ = (vg);
                *pf++ = (vr);

vb, vg, vr are blue, green, red values. Since the driver is still v4l1 this can be normal(?)

Cheers,
Thierry

#3 lore raw

Hi Thierry

Quoted 28 lines · Thierry Merle

Hi Mauro,

Quoted 12 lines · Mauro Carvalho Chehab

Em Ter, 2007-11-06 às 18:25 +0100, Markus Hirschmann escreveu:

Quoted 7 lines

Hello Kernel-Developer,

Module quickcam_messenger seems to be broken (tried 2.6.18 and 2.6.22)
on 2 different NSLU2 (ARM). Picture is attached. Same kernel and module can be used without any problems on x86 here. I don't have any ARM device beside the NSLU2, so I cannot check.

The solution was to use Christian Magnusson's quickcam module. Everything worked without any problem. Webcam is:

Hmm... you're mentioning the quickcam module, but some of your logs are related to usbvideo driver.

Quoted 8 lines

On a quick glance, I didn't find anything that could explain your troubles. It seems to be related to a wrong order at the output format (for example, the driver is sending RGB, instead of BGR).

It may also be an issue at the userspace application that is using the wrong logic to deal with Big Endian.

The NSLU2 is based on a IXP420 processor that can change its endianess. I suppose Markus has installed the debian-arm distribution on his NSLU2 so it is configured as little-endian.
Nevertheless, I took a look at the code of quickcam messenger that is in usbvideo/
This macro: RGB24_PUTPIXEL puts in memory the following bytes:

Quoted 5 lines
                *pf++ = (vb);
                *pf++ = (vg);
                *pf++ = (vr);

vb, vg, vr are blue, green, red values. Since the driver is still v4l1 this can be normal(?)

Right, I forgot. Installed is the Debian ARM distribution. And I tried serveral different applications (motion, vgrabbj).

Best regards

Markus