Skip to contentSkip to conversation

WM97xx touchscreen drivers

PATCH Superseded Mark Brown 3 participants 16 messages Jan 26, 2008 – Feb 8, 2008

Subsystems (3)

v4 of 7 Superseded Latest is v7 →

lore
Share & tools
lore

Mark Brown

author
#0 lore raw

PATCH v4 1/1 WM97xx touchscreen drivers

This patch series adds support for the touchscreen controllers provided by Wolfson Microelectronics WM97xx series chips in both polled and streaming modes.

Changes since last submission:
- Fix from Dmitry Baryshkov for build with CONFIG_PM.
- Add the web site to the MAINTAINERS entry.

author
#1 lore raw

PATCH 1/6 Core driver for WM97xx touchscreens

This patch series adds support for the touchscreen controllers provided by Wolfson Microelectronics WM97xx series chips in both polled and streaming modes.

These drivers have been maintained out of tree since 2003. During that time the driver the primary maintainer was Liam Girdwood and a number of people have made contributions including Stanley Cai, Rodolfo Giometti, Russell King, Marc Kleine-Budde, Ian Molton, Vincent Sanders, Andrew Zabolotny, Graeme Gregory, Mike Arthur and myself. Apologies to anyone I have omitted.

Cc Dmitry Baryshkov <[email protected]>
Cc Stanley Cai <[email protected]>
Cc Rodolfo Giometti <[email protected]>
Cc Russell King <[email protected]>
Cc Marc Kleine-Budde <[email protected]>
Cc Ian Molton <[email protected]>
Cc Vincent Sanders <[email protected]>
Cc Andrew Zabolotny <[email protected]>
---
 drivers/input/touchscreen/wm97xx-core.c |  724 +++++++++++++++++++++++++++++++
 include/linux/wm97xx.h                  |  309 +++++++++++++
 2 files changed, 1033 insertions(+), 0 deletions(-)
 create mode 100644 drivers/input/touchscreen/wm97xx-core.c
 create mode 100644 include/linux/wm97xx.h
drivers/input/touchscreen/wm97xx-core.c new file +724 -0
new file mode 100644
index 0000000..27a0a99
@@ -0,0 +1,724 @@
+/*
+ * wm97xx-core.c  --  Touch screen driver core for Wolfson WM9705, WM9712
+ *                    and WM9713 AC97 Codecs.
+ *
+ * Copyright 2003, 2004, 2005, 2006, 2007, 2008 Wolfson Microelectronics PLC.
+ * Author: Liam Girdwood
+ *         [email protected] or [email protected]
+ * Parts Copyright : Ian Molton <[email protected]>
+ *                   Andrew Zabolotny <[email protected]>
+ *                   Russell King <[email protected]>
+ *
+ *  This program is free software; you can redistribute  it and/or modify it
+ *  under  the terms of  the GNU General  Public License as published by the
+ *  Free Software Foundation;  either version 2 of the  License, or (at your
+ *  option) any later version.
+ *
+ * Notes:
+ *
+ *  Features:
+ *       - supports WM9705, WM9712, WM9713
+ *       - polling mode
+ *       - continuous mode (arch-dependent)
+ *       - adjustable rpu/dpp settings
+ *       - adjustable pressure current
+ *       - adjustable sample settle delay
+ *       - 4 and 5 wire touchscreens (5 wire is WM9712 only)
+ *       - pen down detection
+ *       - battery monitor
+ *       - sample AUX adcs
+ *       - power management
+ *       - codec GPIO
+ *       - codec event notification
+ * Todo
+ *       - Support for async sampling control for noisy LCDs.
+ *
+ */
+
+#include <linux/module.h>
+#include <linux/moduleparam.h>
+#include <linux/version.h>
+#include <linux/kernel.h>
+#include <linux/init.h>
+#include <linux/delay.h>
+#include <linux/string.h>
+#include <linux/proc_fs.h>
+#include <linux/pm.h>
+#include <linux/interrupt.h>
+#include <linux/bitops.h>
+#include <linux/workqueue.h>
+#include <linux/wm97xx.h>
+#include <linux/uaccess.h>
+#include <linux/io.h>
+
+#define TS_NAME			"wm97xx"
+#define WM_CORE_VERSION		"0.65"
+#define DEFAULT_PRESSURE	0xb0c0
+
+
+/*
+ * Touchscreen absolute values
+ *
+ * These parameters are used to help the input layer discard out of
+ * range readings and reduce jitter etc.
+ *
+ *   o min, max:- indicate the min and max values your touch screen returns
+ *   o fuzz:- use a higher number to reduce jitter
+ *
+ * The default values correspond to Mainstone II in QVGA mode
+ *
+ * Please read
+ * Documentation/input/input-programming.txt for more details.
+ */
+
+static int abs_x[3] = {350, 3900, 5};
+module_param_array(abs_x, int, NULL, 0);
+MODULE_PARM_DESC(abs_x, "Touchscreen absolute X min, max, fuzz");
+
+static int abs_y[3] = {320, 3750, 40};
+module_param_array(abs_y, int, NULL, 0);
+MODULE_PARM_DESC(abs_y, "Touchscreen absolute Y min, max, fuzz");
+
+static int abs_p[3] = {0, 150, 4};
+module_param_array(abs_p, int, NULL, 0);
+MODULE_PARM_DESC(abs_p, "Touchscreen absolute Pressure min, max, fuzz");
+
+/*
+ * wm97xx IO access, all IO locking done by AC97 layer
+ */
+int wm97xx_reg_read(struct wm97xx *wm, u16 reg)
+{
+	if (wm->ac97)
+		return wm->ac97->bus->ops->read(wm->ac97, reg);
+	else
+		return -1;
+}
+EXPORT_SYMBOL_GPL(wm97xx_reg_read);
+
+void wm97xx_reg_write(struct wm97xx *wm, u16 reg, u16 val)
+{
+	/* cache digitiser registers */
+	if (reg >= AC97_WM9713_DIG1 && reg <= AC97_WM9713_DIG3)
+		wm->dig[(reg - AC97_WM9713_DIG1) >> 1] = val;
+
+	/* cache gpio regs */
+	if (reg >= AC97_GPIO_CFG && reg <= AC97_MISC_AFE)
+		wm->gpio[(reg - AC97_GPIO_CFG) >> 1] = val;
+
+	/* wm9713 irq reg */
+	if (reg == 0x5a)
+		wm->misc = val;
+
+	if (wm->ac97)
+		wm->ac97->bus->ops->write(wm->ac97, reg, val);
+}
+EXPORT_SYMBOL_GPL(wm97xx_reg_write);
+
+/**
+ *	wm97xx_read_aux_adc - Read the aux adc.
+ *	@wm: wm97xx device.
+ *  @adcsel: codec ADC to be read
+ *
+ *	Reads the selected AUX ADC.
+ */
+
+int wm97xx_read_aux_adc(struct wm97xx *wm, u16 adcsel)
+{
+	int power_adc = 0, auxval;
+	u16 power = 0;
+
+	/* get codec */
+	mutex_lock(&wm->codec_mutex);
+
+	/* When the touchscreen is not in use, we may have to power up
+	 * the AUX ADC before we can use sample the AUX inputs->
+	 */
+	if (wm->id == WM9713_ID2 &&
+	    (power = wm97xx_reg_read(wm, AC97_EXTENDED_MID)) & 0x8000) {
+		power_adc = 1;
+		wm97xx_reg_write(wm, AC97_EXTENDED_MID, power & 0x7fff);
+	}
+
+	/* Prepare the codec for AUX reading */
+	wm->codec->aux_prepare(wm);
+
+	/* Turn polling mode on to read AUX ADC */
+	wm->pen_probably_down = 1;
+	wm->codec->poll_sample(wm, adcsel, &auxval);
+
+	if (power_adc)
+		wm97xx_reg_write(wm, AC97_EXTENDED_MID, power | 0x8000);
+
+	wm->codec->dig_restore(wm);
+
+	wm->pen_probably_down = 0;
+
+	mutex_unlock(&wm->codec_mutex);
+	return auxval & 0xfff;
+}
+EXPORT_SYMBOL_GPL(wm97xx_read_aux_adc);
+
+/**
+ *	wm97xx_get_gpio - Get the status of a codec GPIO.
+ *	@wm: wm97xx device.
+ *      @gpio: gpio
+ *
+ *	Get the status of a codec GPIO pin
+ */
+
+enum wm97xx_gpio_status wm97xx_get_gpio(struct wm97xx *wm, u32 gpio)
+{
+	u16 status;
+	enum wm97xx_gpio_status ret;
+
+	mutex_lock(&wm->codec_mutex);
+	status = wm97xx_reg_read(wm, AC97_GPIO_STATUS);
+
+	if (status & gpio)
+		ret = WM97XX_GPIO_HIGH;
+	else
+		ret = WM97XX_GPIO_LOW;
+
+	mutex_unlock(&wm->codec_mutex);
+	return ret;
+}
+EXPORT_SYMBOL_GPL(wm97xx_get_gpio);
+
+/**
+ *	wm97xx_set_gpio - Set the status of a codec GPIO.
+ *	@wm: wm97xx device.
+ *  @gpio: gpio
+ *
+ *
+ *	Set the status of a codec GPIO pin
+ */
+
+void wm97xx_set_gpio(struct wm97xx *wm, u32 gpio,
+				enum wm97xx_gpio_status status)
+{
+	u16 reg;
+
+	mutex_lock(&wm->codec_mutex);
+	reg = wm97xx_reg_read(wm, AC97_GPIO_STATUS);
+
+	if (status & WM97XX_GPIO_HIGH)
+		reg |= gpio;
+	else
+		reg &= ~gpio;
+
+	if (wm->id == WM9712_ID2)
+		wm97xx_reg_write(wm, AC97_GPIO_STATUS, reg << 1);
+	else
+		wm97xx_reg_write(wm, AC97_GPIO_STATUS, reg);
+	mutex_unlock(&wm->codec_mutex);
+}
+EXPORT_SYMBOL_GPL(wm97xx_set_gpio);
+
+/*
+ * Codec GPIO pin configuration, this sets pin direction, polarity,
+ * stickyness and wake up.
+ */
+void wm97xx_config_gpio(struct wm97xx *wm, u32 gpio, enum wm97xx_gpio_dir dir,
+		   enum wm97xx_gpio_pol pol, enum wm97xx_gpio_sticky sticky,
+		   enum wm97xx_gpio_wake wake)
+{
+	u16 reg;
+
+	mutex_lock(&wm->codec_mutex);
+	reg = wm97xx_reg_read(wm, AC97_GPIO_POLARITY);
+
+	if (pol == WM97XX_GPIO_POL_HIGH)
+		reg |= gpio;
+	else
+		reg &= ~gpio;
+
+	wm97xx_reg_write(wm, AC97_GPIO_POLARITY, reg);
+	reg = wm97xx_reg_read(wm, AC97_GPIO_STICKY);
+
+	if (sticky == WM97XX_GPIO_STICKY)
+		reg |= gpio;
+	else
+		reg &= ~gpio;
+
+	wm97xx_reg_write(wm, AC97_GPIO_STICKY, reg);
+	reg = wm97xx_reg_read(wm, AC97_GPIO_WAKEUP);
+
+	if (wake == WM97XX_GPIO_WAKE)
+		reg |= gpio;
+	else
+		reg &= ~gpio;
+
+	wm97xx_reg_write(wm, AC97_GPIO_WAKEUP, reg);
+	reg = wm97xx_reg_read(wm, AC97_GPIO_CFG);
+
+	if (dir == WM97XX_GPIO_IN)
+		reg |= gpio;
+	else
+		reg &= ~gpio;
+
+	wm97xx_reg_write(wm, AC97_GPIO_CFG, reg);
+	mutex_unlock(&wm->codec_mutex);
+}
+EXPORT_SYMBOL_GPL(wm97xx_config_gpio);
+
+/*
+ * Handle a pen down interrupt.
+ */
+static void wm97xx_pen_irq_worker(struct work_struct *work)
+{
+	struct wm97xx *wm = container_of(work, struct wm97xx, pen_event_work);
+
+	/* do we need to enable the touch panel reader */
+	if (wm->id == WM9705_ID2) {
+		if (wm97xx_reg_read(wm, AC97_WM97XX_DIGITISER_RD) &
+					WM97XX_PEN_DOWN)
+			wm->pen_is_down = 1;
+		else
+			wm->pen_is_down = 0;
+	} else {
+		u16 status, pol;
+		mutex_lock(&wm->codec_mutex);
+		status = wm97xx_reg_read(wm, AC97_GPIO_STATUS);
+		pol = wm97xx_reg_read(wm, AC97_GPIO_POLARITY);
+
+		if (WM97XX_GPIO_13 & pol & status) {
+			wm->pen_is_down = 1;
+			wm97xx_reg_write(wm, AC97_GPIO_POLARITY, pol &
+						~WM97XX_GPIO_13);
+		} else {
+			wm->pen_is_down = 0;
+			wm97xx_reg_write(wm, AC97_GPIO_POLARITY, pol |
+					 WM97XX_GPIO_13);
+		}
+
+		if (wm->id == WM9712_ID2)
+			wm97xx_reg_write(wm, AC97_GPIO_STATUS, (status &
+						~WM97XX_GPIO_13) << 1);
+		else
+			wm97xx_reg_write(wm, AC97_GPIO_STATUS, status &
+						~WM97XX_GPIO_13);
+		mutex_unlock(&wm->codec_mutex);
+	}
+
+	queue_delayed_work(wm->ts_workq, &wm->ts_reader, 0);
+
+	if (!wm->pen_is_down && wm->mach_ops && wm->mach_ops->acc_enabled)
+		wm->mach_ops->acc_pen_up(wm);
+	wm->mach_ops->irq_enable(wm, 1);
+}
+
+/*
+ * Codec PENDOWN irq handler
+ *
+ * We have to disable the codec interrupt in the handler because it can
+ * take upto 1ms to clear the interrupt source. The interrupt is then enabled
+ * again in the slow handler when the source has been cleared.
+ */
+static irqreturn_t wm97xx_pen_interrupt(int irq, void *dev_id)
+{
+	struct wm97xx *wm = dev_id;
+	wm->mach_ops->irq_enable(wm, 0);
+	queue_work(wm->ts_workq, &wm->pen_event_work);
+	return IRQ_HANDLED;
+}
+
+/*
+ * initialise pen IRQ handler and workqueue
+ */
+static int wm97xx_init_pen_irq(struct wm97xx *wm)
+{
+	u16 reg;
+
+	/* If an interrupt is supplied an IRQ enable operation must also be
+	 * provided. */
+	BUG_ON(!wm->mach_ops->irq_enable);
+
+	INIT_WORK(&wm->pen_event_work, wm97xx_pen_irq_worker);
+
+	if (request_irq(wm->pen_irq, wm97xx_pen_interrupt, IRQF_SHARED,
+			"wm97xx-pen", wm)) {
+		dev_err(wm->dev,
+			"Failed to register pen down interrupt, polling");
+		wm->pen_irq = 0;
+		return -EINVAL;
+	}
+
+	/* enable PEN down on wm9712/13 */
+	if (wm->id != WM9705_ID2) {
+		reg = wm97xx_reg_read(wm, AC97_MISC_AFE);
+		wm97xx_reg_write(wm, AC97_MISC_AFE, reg & 0xfffb);
+		reg = wm97xx_reg_read(wm, 0x5a);
+		wm97xx_reg_write(wm, 0x5a, reg & ~0x0001);
+	}
+
+	return 0;
+}
+
+static int wm97xx_read_samples(struct wm97xx *wm)
+{
+	struct wm97xx_data data;
+	int rc;
+
+	mutex_lock(&wm->codec_mutex);
+
+	if (wm->mach_ops && wm->mach_ops->acc_enabled)
+		rc = wm->mach_ops->acc_pen_down(wm);
+	else
+		rc = wm->codec->poll_touch(wm, &data);
+
+	if (rc & RC_PENUP) {
+		if (wm->pen_is_down) {
+			wm->pen_is_down = 0;
+			dev_dbg(wm->dev, "pen up\n");
+			input_report_abs(wm->input_dev, ABS_PRESSURE, 0);
+			input_sync(wm->input_dev);
+		} else if (!(rc & RC_AGAIN)) {
+			/* We need high frequency updates only while
+			* pen is down, the user never will be able to
+			* touch screen faster than a few times per
+			* second... On the other hand, when the user
+			* is actively working with the touchscreen we
+			* don't want to lose the quick response. So we
+			* will slowly increase sleep time after the
+			* pen is up and quicky restore it to ~one task
+			* switch when pen is down again.
+			*/
+			if (wm->ts_reader_interval < HZ / 10)
+				wm->ts_reader_interval++;
+		}
+
+	} else if (rc & RC_VALID) {
+		dev_dbg(wm->dev,
+			"pen down: x=%x:%d, y=%x:%d, pressure=%x:%d\n",
+			data.x >> 12, data.x & 0xfff, data.y >> 12,
+			data.y & 0xfff, data.p >> 12, data.p & 0xfff);
+		input_report_abs(wm->input_dev, ABS_X, data.x & 0xfff);
+		input_report_abs(wm->input_dev, ABS_Y, data.y & 0xfff);
+		input_report_abs(wm->input_dev, ABS_PRESSURE, data.p & 0xfff);
+		input_sync(wm->input_dev);
+		wm->pen_is_down = 1;
+		wm->ts_reader_interval = wm->ts_reader_min_interval;
+	} else if (rc & RC_PENDOWN) {
+		dev_dbg(wm->dev, "pen down");
+		wm->pen_is_down = 1;
+		wm->ts_reader_interval = wm->ts_reader_min_interval;
+	}
+
+	mutex_unlock(&wm->codec_mutex);
+	return rc;
+}
+
+/*
+* The touchscreen sample reader.
+*/
+static void wm97xx_ts_reader(struct work_struct *work)
+{
+	int rc;
+	struct wm97xx *wm = container_of(work, struct wm97xx, ts_reader.work);
+
+	BUG_ON(!wm->codec);
+
+	do {
+		rc = wm97xx_read_samples(wm);
+	} while (rc & RC_AGAIN);
+
+	if (wm->pen_is_down || !wm->pen_irq)
+		queue_delayed_work(wm->ts_workq, &wm->ts_reader,
+				   wm->ts_reader_interval);
+}
+
+/**
+ *	wm97xx_ts_input_open - Open the touch screen input device.
+ *	@idev:	Input device to be opened.
+ *
+ *	Called by the input sub system to open a wm97xx touchscreen device.
+ *  Starts the touchscreen thread and touch digitiser.
+ */
+static int wm97xx_ts_input_open(struct input_dev *idev)
+{
+	struct wm97xx *wm = input_get_drvdata(idev);
+
+	wm->ts_workq = create_singlethread_workqueue("kwm97xx");
+	if (wm->ts_workq == NULL) {
+		dev_err(wm->dev,
+			"Failed to create workqueue\n");
+		return -EINVAL;
+	}
+
+	/* start digitiser */
+	if (wm->mach_ops && wm->mach_ops->acc_enabled)
+		wm->codec->acc_enable(wm, 1);
+	wm->codec->dig_enable(wm, 1);
+
+	INIT_DELAYED_WORK(&wm->ts_reader, wm97xx_ts_reader);
+
+	wm->ts_reader_min_interval = HZ >= 100 ? HZ / 100 : 1;
+	if (wm->ts_reader_min_interval < 1)
+		wm->ts_reader_min_interval = 1;
+	wm->ts_reader_interval = wm->ts_reader_min_interval;
+
+	wm->pen_is_down = 0;
+	if (wm->pen_irq)
+		wm97xx_init_pen_irq(wm);
+	else
+		dev_err(wm->dev, "No IRQ specified\n");
+
+	/* If we either don't have an interrupt for pen down events or
+	 * failed to acquire it then we need to poll.
+	 */
+	if (wm->pen_irq == 0)
+		queue_delayed_work(wm->ts_workq, &wm->ts_reader,
+				   wm->ts_reader_interval);
+
+	return 0;
+}
+
+/**
+ *	wm97xx_ts_input_close - Close the touch screen input device.
+ *	@idev:	Input device to be closed.
+ *
+ *	Called by the input sub system to close a wm97xx touchscreen device.
+ *  Kills the touchscreen thread and stops the touch digitiser.
+ */
+
+static void wm97xx_ts_input_close(struct input_dev *idev)
+{
+	struct wm97xx *wm = input_get_drvdata(idev);
+
+	if (wm->pen_irq)
+		free_irq(wm->pen_irq, wm);
+
+	wm->pen_is_down = 0;
+
+	/* ts_reader rearms itself so we need to explicitly stop it
+	 * before we destroy the workqueue.
+	 */
+	cancel_delayed_work_sync(&wm->ts_reader);
+	destroy_workqueue(wm->ts_workq);
+
+	/* stop digitiser */
+	wm->codec->dig_enable(wm, 0);
+	if (wm->mach_ops && wm->mach_ops->acc_enabled)
+		wm->codec->acc_enable(wm, 0);
+}
+
+static int wm97xx_probe(struct device *dev)
+{
+	struct wm97xx *wm;
+	int ret = 0, id = 0;
+
+	wm = kzalloc(sizeof(struct wm97xx), GFP_KERNEL);
+	if (!wm)
+		return -ENOMEM;
+	mutex_init(&wm->codec_mutex);
+
+	wm->dev = dev;
+	dev->driver_data = wm;
+	wm->ac97 = to_ac97_t(dev);
+
+	/* check that we have a supported codec */
+	id = wm97xx_reg_read(wm, AC97_VENDOR_ID1);
+	if (id != WM97XX_ID1) {
+		dev_err(dev, "Device with vendor %04x is not a wm97xx\n", id);
+		kfree(wm);
+		return -ENODEV;
+	}
+
+	wm->id = wm97xx_reg_read(wm, AC97_VENDOR_ID2);
+
+	dev_info(wm->dev, "detected a wm97%02x codec", wm->id & 0xff);
+
+	switch (wm->id & 0xff) {
+#ifdef CONFIG_TOUCHSCREEN_WM9705
+	case 0x05:
+		wm->codec = &wm9705_codec;
+		break;
+#endif
+#ifdef CONFIG_TOUCHSCREEN_WM9712
+	case 0x12:
+		wm->codec = &wm9712_codec;
+		break;
+#endif
+#ifdef CONFIG_TOUCHSCREEN_WM9713
+	case 0x13:
+		wm->codec = &wm9713_codec;
+		break;
+#endif
+	default:
+		dev_err(wm->dev, "Support for wm97%02x not compiled in.\n",
+			wm->id & 0xff);
+		kfree(wm);
+		return -ENODEV;
+	}
+
+	wm->input_dev = input_allocate_device();
+	if (wm->input_dev == NULL) {
+		kfree(wm);
+		return -ENOMEM;
+	}
+
+	/* set up touch configuration */
+	wm->input_dev->name = "wm97xx touchscreen";
+	wm->input_dev->open = wm97xx_ts_input_open;
+	wm->input_dev->close = wm97xx_ts_input_close;
+	set_bit(EV_ABS, wm->input_dev->evbit);
+	set_bit(ABS_X, wm->input_dev->absbit);
+	set_bit(ABS_Y, wm->input_dev->absbit);
+	set_bit(ABS_PRESSURE, wm->input_dev->absbit);
+	input_set_abs_params(wm->input_dev, ABS_X, abs_x[0], abs_x[1],
+			     abs_x[2], 0);
+	input_set_abs_params(wm->input_dev, ABS_Y, abs_y[0], abs_y[1],
+			     abs_y[2], 0);
+	input_set_abs_params(wm->input_dev, ABS_PRESSURE, abs_p[0], abs_p[1],
+			     abs_p[2], 0);
+	input_set_drvdata(wm->input_dev, wm);
+	wm->input_dev->dev.parent = dev;
+	ret = input_register_device(wm->input_dev);
+	if (ret < 0) {
+		input_free_device(wm->input_dev);
+		kfree(wm);
+		return -ENOMEM;
+	}
+
+	/* set up physical characteristics */
+	wm->codec->phy_init(wm);
+
+	/* load gpio cache */
+	wm->gpio[0] = wm97xx_reg_read(wm, AC97_GPIO_CFG);
+	wm->gpio[1] = wm97xx_reg_read(wm, AC97_GPIO_POLARITY);
+	wm->gpio[2] = wm97xx_reg_read(wm, AC97_GPIO_STICKY);
+	wm->gpio[3] = wm97xx_reg_read(wm, AC97_GPIO_WAKEUP);
+	wm->gpio[4] = wm97xx_reg_read(wm, AC97_GPIO_STATUS);
+	wm->gpio[5] = wm97xx_reg_read(wm, AC97_MISC_AFE);
+
+	/* register our battery device */
+	wm->battery_dev = platform_device_alloc("wm97xx-battery", 0);
+	if (!wm->battery_dev)
+		goto batt_err;
+	platform_set_drvdata(wm->battery_dev, wm);
+	wm->battery_dev->dev.parent = dev;
+	ret = platform_device_register(wm->battery_dev);
+	if (ret < 0)
+		goto batt_reg_err;
+
+	/* register our extended touch device (for machine specific
+	 * extensions) */
+	wm->touch_dev = platform_device_alloc("wm97xx-touch", 0);
+	if (!wm->touch_dev)
+		goto touch_err;
+	platform_set_drvdata(wm->touch_dev, wm);
+	wm->touch_dev->dev.parent = dev;
+	ret = platform_device_register(wm->touch_dev);
+	if (ret < 0)
+		goto touch_reg_err;
+
+	return ret;
+
+ touch_reg_err:
+	platform_device_put(wm->touch_dev);
+ touch_err:
+	platform_device_unregister(wm->battery_dev);
+ batt_reg_err:
+	platform_device_put(wm->battery_dev);
+ batt_err:
+	input_unregister_device(wm->input_dev);
+	kfree(wm);
+	return ret;
+}
+
+static int wm97xx_remove(struct device *dev)
+{
+	struct wm97xx *wm = dev_get_drvdata(dev);
+
+	platform_device_unregister(wm->battery_dev);
+	platform_device_unregister(wm->touch_dev);
+	input_unregister_device(wm->input_dev);
+
+	kfree(wm);
+	return 0;
+}
+
+#ifdef CONFIG_PM
+static int wm97xx_resume(struct device *dev)
+{
+	struct wm97xx *wm = dev_get_drvdata(dev);
+
+	/* restore digitiser and gpios */
+	if (wm->id == WM9713_ID2) {
+		wm97xx_reg_write(wm, AC97_WM9713_DIG1, wm->dig[0]);
+		wm97xx_reg_write(wm, 0x5a, wm->misc);
+		if (wm->input_dev->users) {
+			u16 reg;
+			reg = wm97xx_reg_read(wm, AC97_EXTENDED_MID) & 0x7fff;
+			wm97xx_reg_write(wm, AC97_EXTENDED_MID, reg);
+		}
+	}
+
+	wm97xx_reg_write(wm, AC97_WM9713_DIG2, wm->dig[1]);
+	wm97xx_reg_write(wm, AC97_WM9713_DIG3, wm->dig[2]);
+
+	wm97xx_reg_write(wm, AC97_GPIO_CFG, wm->gpio[0]);
+	wm97xx_reg_write(wm, AC97_GPIO_POLARITY, wm->gpio[1]);
+	wm97xx_reg_write(wm, AC97_GPIO_STICKY, wm->gpio[2]);
+	wm97xx_reg_write(wm, AC97_GPIO_WAKEUP, wm->gpio[3]);
+	wm97xx_reg_write(wm, AC97_GPIO_STATUS, wm->gpio[4]);
+	wm97xx_reg_write(wm, AC97_MISC_AFE, wm->gpio[5]);
+
+	return 0;
+}
+
+#else
+#define wm97xx_resume		NULL
+#endif
+
+/*
+ * Machine specific operations
+ */
+int wm97xx_register_mach_ops(struct wm97xx *wm,
+			     struct wm97xx_mach_ops *mach_ops)
+{
+	mutex_lock(&wm->codec_mutex);
+	if (wm->mach_ops) {
+		mutex_unlock(&wm->codec_mutex);
+		return -EINVAL;
+	}
+	wm->mach_ops = mach_ops;
+	mutex_unlock(&wm->codec_mutex);
+	return 0;
+}
+EXPORT_SYMBOL_GPL(wm97xx_register_mach_ops);
+
+void wm97xx_unregister_mach_ops(struct wm97xx *wm)
+{
+	mutex_lock(&wm->codec_mutex);
+	wm->mach_ops = NULL;
+	mutex_unlock(&wm->codec_mutex);
+}
+EXPORT_SYMBOL_GPL(wm97xx_unregister_mach_ops);
+
+static struct device_driver wm97xx_driver = {
+	.name = 	"ac97",
+	.bus = 		&ac97_bus_type,
+	.owner = 	THIS_MODULE,
+	.probe = 	wm97xx_probe,
+	.remove = 	wm97xx_remove,
+	.resume =	wm97xx_resume,
+};
+
+static int __init wm97xx_init(void)
+{
+	return driver_register(&wm97xx_driver);
+}
+
+static void __exit wm97xx_exit(void)
+{
+	driver_unregister(&wm97xx_driver);
+}
+
+module_init(wm97xx_init);
+module_exit(wm97xx_exit);
+
+/* Module information */
+MODULE_AUTHOR("Liam Girdwood <[email protected]>");
+MODULE_DESCRIPTION("WM97xx Core - Touch Screen / AUX ADC / GPIO Driver");
+MODULE_LICENSE("GPL");
include/linux/wm97xx.h new file +309 -0

309 lines not on this page · raw message

Signature · 1 line
1.5.3.8
author
#2 lore raw

PATCH 2/6 Add chip driver for WM9705 touchscreen

Cc Dmitry Baryshkov <[email protected]>
Cc Stanley Cai <[email protected]>
Cc Rodolfo Giometti <[email protected]>
Cc Russell King <[email protected]>
Cc Marc Kleine-Budde <[email protected]>
Cc Ian Molton <[email protected]>
Cc Vince Sanders <[email protected]>
Cc Andrew Zabolotny <[email protected]>
---
 drivers/input/touchscreen/wm9705.c |  352 ++++++++++++++++++++++++++++++++++++
 1 files changed, 352 insertions(+), 0 deletions(-)
 create mode 100644 drivers/input/touchscreen/wm9705.c
drivers/input/touchscreen/wm9705.c new file +352 -0
new file mode 100644
index 0000000..f185104
@@ -0,0 +1,352 @@
+/*
+ * wm9705.c  --  Codec driver for Wolfson WM9705 AC97 Codec.
+ *
+ * Copyright 2003, 2004, 2005, 2006, 2007 Wolfson Microelectronics PLC.
+ * Author: Liam Girdwood
+ *         [email protected] or [email protected]
+ * Parts Copyright : Ian Molton <[email protected]>
+ *                   Andrew Zabolotny <[email protected]>
+ *                   Russell King <[email protected]>
+ *
+ *  This program is free software; you can redistribute  it and/or modify it
+ *  under  the terms of  the GNU General  Public License as published by the
+ *  Free Software Foundation;  either version 2 of the  License, or (at your
+ *  option) any later version.
+ *
+ */
+
+#include <linux/module.h>
+#include <linux/moduleparam.h>
+#include <linux/version.h>
+#include <linux/kernel.h>
+#include <linux/input.h>
+#include <linux/delay.h>
+#include <linux/bitops.h>
+#include <linux/wm97xx.h>
+
+#define TS_NAME			"wm97xx"
+#define WM9705_VERSION		"0.62"
+#define DEFAULT_PRESSURE	0xb0c0
+
+/*
+ * Module parameters
+ */
+
+/*
+ * Set current used for pressure measurement.
+ *
+ * Set pil = 2 to use 400uA
+ *     pil = 1 to use 200uA and
+ *     pil = 0 to disable pressure measurement.
+ *
+ * This is used to increase the range of values returned by the adc
+ * when measureing touchpanel pressure.
+ */
+static int pil;
+module_param(pil, int, 0);
+MODULE_PARM_DESC(pil, "Set current used for pressure measurement.");
+
+/*
+ * Set threshold for pressure measurement.
+ *
+ * Pen down pressure below threshold is ignored.
+ */
+static int pressure = DEFAULT_PRESSURE & 0xfff;
+module_param(pressure, int, 0);
+MODULE_PARM_DESC(pressure, "Set threshold for pressure measurement.");
+
+/*
+ * Set adc sample delay.
+ *
+ * For accurate touchpanel measurements, some settling time may be
+ * required between the switch matrix applying a voltage across the
+ * touchpanel plate and the ADC sampling the signal.
+ *
+ * This delay can be set by setting delay = n, where n is the array
+ * position of the delay in the array delay_table below.
+ * Long delays > 1ms are supported for completeness, but are not
+ * recommended.
+ */
+static int delay = 4;
+module_param(delay, int, 0);
+MODULE_PARM_DESC(delay, "Set adc sample delay.");
+
+/*
+ * Pen detect comparator threshold.
+ *
+ * 0 to Vmid in 15 steps, 0 = use zero power comparator with Vmid threshold
+ * i.e. 1 =  Vmid/15 threshold
+ *      15 =  Vmid/1 threshold
+ *
+ * Adjust this value if you are having problems with pen detect not
+ * detecting any down events.
+ */
+static int pdd = 8;
+module_param(pdd, int, 0);
+MODULE_PARM_DESC(pdd, "Set pen detect comparator threshold");
+
+/*
+ * Set adc mask function.
+ *
+ * Sources of glitch noise, such as signals driving an LCD display, may feed
+ * through to the touch screen plates and affect measurement accuracy. In
+ * order to minimise this, a signal may be applied to the MASK pin to delay or
+ * synchronise the sampling.
+ *
+ * 0 = No delay or sync
+ * 1 = High on pin stops conversions
+ * 2 = Edge triggered, edge on pin delays conversion by delay param (above)
+ * 3 = Edge triggered, edge on pin starts conversion after delay param
+ */
+static int mask;
+module_param(mask, int, 0);
+MODULE_PARM_DESC(mask, "Set adc mask function.");
+
+/*
+ * ADC sample delay times in uS
+ */
+static const int delay_table[] = {
+	21,    /* 1 AC97 Link frames */
+	42,    /* 2                  */
+	84,    /* 4                  */
+	167,   /* 8                  */
+	333,   /* 16                 */
+	667,   /* 32                 */
+	1000,  /* 48                 */
+	1333,  /* 64                 */
+	2000,  /* 96                 */
+	2667,  /* 128                */
+	3333,  /* 160                */
+	4000,  /* 192                */
+	4667,  /* 224                */
+	5333,  /* 256                */
+	6000,  /* 288                */
+	0      /* No delay, switch matrix always on */
+};
+
+/*
+ * Delay after issuing a POLL command.
+ *
+ * The delay is 3 AC97 link frames + the touchpanel settling delay
+ */
+static inline void poll_delay(int d)
+{
+	udelay(3 * AC97_LINK_FRAME + delay_table[d]);
+}
+
+/*
+ * set up the physical settings of the WM9705
+ */
+static void wm9705_phy_init(struct wm97xx *wm)
+{
+	u16 dig1 = 0, dig2 = WM97XX_RPR;
+
+	/*
+	* mute VIDEO and AUX as they share X and Y touchscreen
+	* inputs on the WM9705
+	*/
+	wm97xx_reg_write(wm, AC97_AUX, 0x8000);
+	wm97xx_reg_write(wm, AC97_VIDEO, 0x8000);
+
+	/* touchpanel pressure current*/
+	if (pil == 2) {
+		dig2 |= WM9705_PIL;
+		dev_dbg(wm->dev,
+			"setting pressure measurement current to 400uA.");
+	} else if (pil)
+		dev_dbg(wm->dev,
+			"setting pressure measurement current to 200uA.");
+	if (!pil)
+		pressure = 0;
+
+	/* polling mode sample settling delay */
+	if (delay != 4) {
+		if (delay < 0 || delay > 15) {
+			dev_dbg(wm->dev, "supplied delay out of range.");
+			delay = 4;
+		}
+	}
+	dig1 &= 0xff0f;
+	dig1 |= WM97XX_DELAY(delay);
+	dev_dbg(wm->dev, "setting adc sample delay to %d u Secs.",
+		delay_table[delay]);
+
+	/* WM9705 pdd */
+	dig2 |= (pdd & 0x000f);
+	dev_dbg(wm->dev, "setting pdd to Vmid/%d", 1 - (pdd & 0x000f));
+
+	/* mask */
+	dig2 |= ((mask & 0x3) << 4);
+
+	wm97xx_reg_write(wm, AC97_WM97XX_DIGITISER1, dig1);
+	wm97xx_reg_write(wm, AC97_WM97XX_DIGITISER2, dig2);
+}
+
+static void wm9705_dig_enable(struct wm97xx *wm, int enable)
+{
+	if (enable) {
+		wm97xx_reg_write(wm, AC97_WM97XX_DIGITISER2,
+				 wm->dig[2] | WM97XX_PRP_DET_DIG);
+		wm97xx_reg_read(wm, AC97_WM97XX_DIGITISER_RD); /* dummy read */
+	} else
+		wm97xx_reg_write(wm, AC97_WM97XX_DIGITISER2,
+				 wm->dig[2] & ~WM97XX_PRP_DET_DIG);
+}
+
+static void wm9705_aux_prepare(struct wm97xx *wm)
+{
+	memcpy(wm->dig_save, wm->dig, sizeof(wm->dig));
+	wm97xx_reg_write(wm, AC97_WM97XX_DIGITISER1, 0);
+	wm97xx_reg_write(wm, AC97_WM97XX_DIGITISER2, WM97XX_PRP_DET_DIG);
+}
+
+static void wm9705_dig_restore(struct wm97xx *wm)
+{
+	wm97xx_reg_write(wm, AC97_WM97XX_DIGITISER1, wm->dig_save[1]);
+	wm97xx_reg_write(wm, AC97_WM97XX_DIGITISER2, wm->dig_save[2]);
+}
+
+static inline int is_pden(struct wm97xx *wm)
+{
+	return wm->dig[2] & WM9705_PDEN;
+}
+
+/*
+ * Read a sample from the WM9705 adc in polling mode.
+ */
+static int wm9705_poll_sample(struct wm97xx *wm, int adcsel, int *sample)
+{
+	int timeout = 5 * delay;
+
+	if (!wm->pen_probably_down) {
+		u16 data = wm97xx_reg_read(wm, AC97_WM97XX_DIGITISER_RD);
+		if (!(data & WM97XX_PEN_DOWN))
+			return RC_PENUP;
+		wm->pen_probably_down = 1;
+	}
+
+	/* set up digitiser */
+	if (adcsel & 0x8000)
+		adcsel = ((adcsel & 0x7fff) + 3) << 12;
+
+	if (wm->mach_ops && wm->mach_ops->pre_sample)
+		wm->mach_ops->pre_sample(adcsel);
+	wm97xx_reg_write(wm, AC97_WM97XX_DIGITISER1,
+			 adcsel | WM97XX_POLL | WM97XX_DELAY(delay));
+
+	/* wait 3 AC97 time slots + delay for conversion */
+	poll_delay(delay);
+
+	/* wait for POLL to go low */
+	while ((wm97xx_reg_read(wm, AC97_WM97XX_DIGITISER1) & WM97XX_POLL)
+	       && timeout) {
+		udelay(AC97_LINK_FRAME);
+		timeout--;
+	}
+
+	if (timeout <= 0) {
+		/* If PDEN is set, we can get a timeout when pen goes up */
+		if (is_pden(wm))
+			wm->pen_probably_down = 0;
+		else
+			dev_dbg(wm->dev, "adc sample timeout");
+		return RC_PENUP;
+	}
+
+	*sample = wm97xx_reg_read(wm, AC97_WM97XX_DIGITISER_RD);
+	if (wm->mach_ops && wm->mach_ops->post_sample)
+		wm->mach_ops->post_sample(adcsel);
+
+	/* check we have correct sample */
+	if ((*sample & WM97XX_ADCSEL_MASK) != adcsel) {
+		dev_dbg(wm->dev, "adc wrong sample, read %x got %x", adcsel,
+		*sample & WM97XX_ADCSEL_MASK);
+		return RC_PENUP;
+	}
+
+	if (!(*sample & WM97XX_PEN_DOWN)) {
+		wm->pen_probably_down = 0;
+		return RC_PENUP;
+	}
+
+	return RC_VALID;
+}
+
+/*
+ * Sample the WM9705 touchscreen in polling mode
+ */
+static int wm9705_poll_touch(struct wm97xx *wm, struct wm97xx_data *data)
+{
+	int rc;
+
+	rc = wm9705_poll_sample(wm, WM97XX_ADCSEL_X, &data->x);
+	if (rc != RC_VALID)
+		return rc;
+	rc = wm9705_poll_sample(wm, WM97XX_ADCSEL_Y, &data->y);
+	if (rc != RC_VALID)
+		return rc;
+	if (pil) {
+		rc = wm9705_poll_sample(wm, WM97XX_ADCSEL_PRES, &data->p);
+		if (rc != RC_VALID)
+			return rc;
+	} else
+		data->p = DEFAULT_PRESSURE;
+
+	return RC_VALID;
+}
+
+/*
+ * Enable WM9705 continuous mode, i.e. touch data is streamed across
+ * an AC97 slot
+ */
+static int wm9705_acc_enable(struct wm97xx *wm, int enable)
+{
+	u16 dig1, dig2;
+	int ret = 0;
+
+	dig1 = wm->dig[1];
+	dig2 = wm->dig[2];
+
+	if (enable) {
+		/* continous mode */
+		if (wm->mach_ops->acc_startup &&
+		    (ret = wm->mach_ops->acc_startup(wm)) < 0)
+			return ret;
+		dig1 &= ~(WM97XX_CM_RATE_MASK | WM97XX_ADCSEL_MASK |
+			  WM97XX_DELAY_MASK | WM97XX_SLT_MASK);
+		dig1 |= WM97XX_CTC | WM97XX_COO | WM97XX_SLEN |
+			WM97XX_DELAY(delay) |
+			WM97XX_SLT(wm->acc_slot) |
+			WM97XX_RATE(wm->acc_rate);
+		if (pil)
+			dig1 |= WM97XX_ADCSEL_PRES;
+		dig2 |= WM9705_PDEN;
+	} else {
+		dig1 &= ~(WM97XX_CTC | WM97XX_COO | WM97XX_SLEN);
+		dig2 &= ~WM9705_PDEN;
+		if (wm->mach_ops->acc_shutdown)
+			wm->mach_ops->acc_shutdown(wm);
+	}
+
+	wm97xx_reg_write(wm, AC97_WM97XX_DIGITISER1, dig1);
+	wm97xx_reg_write(wm, AC97_WM97XX_DIGITISER2, dig2);
+	return ret;
+}
+
+struct wm97xx_codec_drv wm9705_codec = {
+	.id = 	WM9705_ID2,
+	.name = "wm9705",
+	.poll_sample = wm9705_poll_sample,
+	.poll_touch = wm9705_poll_touch,
+	.acc_enable = wm9705_acc_enable,
+	.phy_init = wm9705_phy_init,
+	.dig_enable = wm9705_dig_enable,
+	.dig_restore = wm9705_dig_restore,
+	.aux_prepare = wm9705_aux_prepare,
+};
+EXPORT_SYMBOL_GPL(wm9705_codec);
+
+/* Module information */
+MODULE_AUTHOR("Liam Girdwood <[email protected]>");
+MODULE_DESCRIPTION("WM9705 Touch Screen Driver");
+MODULE_LICENSE("GPL");
Signature · 1 line
1.5.3.8
author
#3 lore raw

PATCH 3/6 Add chip driver for WM9712 touchscreen

Cc Dmitry Baryshkov <[email protected]>
Cc Stanley Cai <[email protected]>
Cc Rodolfo Giometti <[email protected]>
Cc Russell King <[email protected]>
Cc Marc Kleine-Budde <[email protected]>
Cc Ian Molton <[email protected]>
Cc Vince Sanders <[email protected]>
Cc Andrew Zabolotny <[email protected]>
---
 drivers/input/touchscreen/wm9712.c |  461 ++++++++++++++++++++++++++++++++++++
 1 files changed, 461 insertions(+), 0 deletions(-)
 create mode 100644 drivers/input/touchscreen/wm9712.c
drivers/input/touchscreen/wm9712.c new file +461 -0
new file mode 100644
index 0000000..eaab326
@@ -0,0 +1,461 @@
+/*
+ * wm9712.c  --  Codec driver for Wolfson WM9712 AC97 Codecs.
+ *
+ * Copyright 2003, 2004, 2005, 2006, 2007 Wolfson Microelectronics PLC.
+ * Author: Liam Girdwood
+ *         [email protected] or [email protected]
+ * Parts Copyright : Ian Molton <[email protected]>
+ *                   Andrew Zabolotny <[email protected]>
+ *                   Russell King <[email protected]>
+ *
+ *  This program is free software; you can redistribute  it and/or modify it
+ *  under  the terms of  the GNU General  Public License as published by the
+ *  Free Software Foundation;  either version 2 of the  License, or (at your
+ *  option) any later version.
+ *
+ */
+
+#include <linux/module.h>
+#include <linux/moduleparam.h>
+#include <linux/version.h>
+#include <linux/kernel.h>
+#include <linux/input.h>
+#include <linux/delay.h>
+#include <linux/bitops.h>
+#include <linux/wm97xx.h>
+
+#define TS_NAME			"wm97xx"
+#define WM9712_VERSION		"0.61"
+#define DEFAULT_PRESSURE	0xb0c0
+
+/*
+ * Module parameters
+ */
+
+/*
+ * Set internal pull up for pen detect.
+ *
+ * Pull up is in the range 1.02k (least sensitive) to 64k (most sensitive)
+ * i.e. pull up resistance = 64k Ohms / rpu.
+ *
+ * Adjust this value if you are having problems with pen detect not
+ * detecting any down event.
+ */
+static int rpu = 8;
+module_param(rpu, int, 0);
+MODULE_PARM_DESC(rpu, "Set internal pull up resitor for pen detect.");
+
+/*
+ * Set current used for pressure measurement.
+ *
+ * Set pil = 2 to use 400uA
+ *     pil = 1 to use 200uA and
+ *     pil = 0 to disable pressure measurement.
+ *
+ * This is used to increase the range of values returned by the adc
+ * when measureing touchpanel pressure.
+ */
+static int pil;
+module_param(pil, int, 0);
+MODULE_PARM_DESC(pil, "Set current used for pressure measurement.");
+
+/*
+ * Set threshold for pressure measurement.
+ *
+ * Pen down pressure below threshold is ignored.
+ */
+static int pressure = DEFAULT_PRESSURE & 0xfff;
+module_param(pressure, int, 0);
+MODULE_PARM_DESC(pressure, "Set threshold for pressure measurement.");
+
+/*
+ * Set adc sample delay.
+ *
+ * For accurate touchpanel measurements, some settling time may be
+ * required between the switch matrix applying a voltage across the
+ * touchpanel plate and the ADC sampling the signal.
+ *
+ * This delay can be set by setting delay = n, where n is the array
+ * position of the delay in the array delay_table below.
+ * Long delays > 1ms are supported for completeness, but are not
+ * recommended.
+ */
+static int delay = 3;
+module_param(delay, int, 0);
+MODULE_PARM_DESC(delay, "Set adc sample delay.");
+
+/*
+ * Set five_wire = 1 to use a 5 wire touchscreen.
+ *
+ * NOTE: Five wire mode does not allow for readback of pressure.
+ */
+static int five_wire;
+module_param(five_wire, int, 0);
+MODULE_PARM_DESC(five_wire, "Set to '1' to use 5-wire touchscreen.");
+
+/*
+ * Set adc mask function.
+ *
+ * Sources of glitch noise, such as signals driving an LCD display, may feed
+ * through to the touch screen plates and affect measurement accuracy. In
+ * order to minimise this, a signal may be applied to the MASK pin to delay or
+ * synchronise the sampling.
+ *
+ * 0 = No delay or sync
+ * 1 = High on pin stops conversions
+ * 2 = Edge triggered, edge on pin delays conversion by delay param (above)
+ * 3 = Edge triggered, edge on pin starts conversion after delay param
+ */
+static int mask;
+module_param(mask, int, 0);
+MODULE_PARM_DESC(mask, "Set adc mask function.");
+
+/*
+ * Coordinate Polling Enable.
+ *
+ * Set to 1 to enable coordinate polling. e.g. x,y[,p] is sampled together
+ * for every poll.
+ */
+static int coord;
+module_param(coord, int, 0);
+MODULE_PARM_DESC(coord, "Polling coordinate mode");
+
+/*
+ * ADC sample delay times in uS
+ */
+static const int delay_table[] = {
+	21,    /* 1 AC97 Link frames */
+	42,    /* 2 */
+	84,    /* 4 */
+	167,   /* 8 */
+	333,   /* 16 */
+	667,   /* 32 */
+	1000,  /* 48 */
+	1333,  /* 64 */
+	2000,  /* 96 */
+	2667,  /* 128 */
+	3333,  /* 160 */
+	4000,  /* 192 */
+	4667,  /* 224 */
+	5333,  /* 256 */
+	6000,  /* 288 */
+	0      /* No delay, switch matrix always on */
+};
+
+/*
+ * Delay after issuing a POLL command.
+ *
+ * The delay is 3 AC97 link frames + the touchpanel settling delay
+ */
+static inline void poll_delay(int d)
+{
+	udelay(3 * AC97_LINK_FRAME + delay_table[d]);
+}
+
+/*
+ * set up the physical settings of the WM9712
+ */
+static void wm9712_phy_init(struct wm97xx *wm)
+{
+	u16 dig1 = 0;
+	u16 dig2 = WM97XX_RPR | WM9712_RPU(1);
+
+	/* WM9712 rpu */
+	if (rpu) {
+		dig2 &= 0xffc0;
+		dig2 |= WM9712_RPU(rpu);
+		dev_dbg(wm->dev, "setting pen detect pull-up to %d Ohms",
+			64000 / rpu);
+	}
+
+	/* touchpanel pressure current*/
+	if (pil == 2) {
+		dig2 |= WM9712_PIL;
+		dev_dbg(wm->dev,
+			"setting pressure measurement current to 400uA.");
+	} else if (pil)
+		dev_dbg(wm->dev,
+			"setting pressure measurement current to 200uA.");
+	if (!pil)
+		pressure = 0;
+
+	/* WM9712 five wire */
+	if (five_wire) {
+		dig2 |= WM9712_45W;
+		dev_dbg(wm->dev, "setting 5-wire touchscreen mode.");
+	}
+
+	/* polling mode sample settling delay */
+	if (delay < 0 || delay > 15) {
+		dev_dbg(wm->dev, "supplied delay out of range.");
+		delay = 4;
+	}
+	dig1 &= 0xff0f;
+	dig1 |= WM97XX_DELAY(delay);
+	dev_dbg(wm->dev, "setting adc sample delay to %d u Secs.",
+		delay_table[delay]);
+
+	/* mask */
+	dig2 |= ((mask & 0x3) << 6);
+	if (mask) {
+		u16 reg;
+		/* Set GPIO4 as Mask Pin*/
+		reg = wm97xx_reg_read(wm, AC97_MISC_AFE);
+		wm97xx_reg_write(wm, AC97_MISC_AFE, reg | WM97XX_GPIO_4);
+		reg = wm97xx_reg_read(wm, AC97_GPIO_CFG);
+		wm97xx_reg_write(wm, AC97_GPIO_CFG, reg | WM97XX_GPIO_4);
+	}
+
+	/* wait - coord mode */
+	if (coord)
+		dig2 |= WM9712_WAIT;
+
+	wm97xx_reg_write(wm, AC97_WM97XX_DIGITISER1, dig1);
+	wm97xx_reg_write(wm, AC97_WM97XX_DIGITISER2, dig2);
+}
+
+static void wm9712_dig_enable(struct wm97xx *wm, int enable)
+{
+	u16 dig2 = wm->dig[2];
+
+	if (enable) {
+		wm97xx_reg_write(wm, AC97_WM97XX_DIGITISER2,
+				 dig2 | WM97XX_PRP_DET_DIG);
+		wm97xx_reg_read(wm, AC97_WM97XX_DIGITISER_RD); /* dummy read */
+	} else
+		wm97xx_reg_write(wm, AC97_WM97XX_DIGITISER2,
+				 dig2 & ~WM97XX_PRP_DET_DIG);
+}
+
+static void wm9712_aux_prepare(struct wm97xx *wm)
+{
+	memcpy(wm->dig_save, wm->dig, sizeof(wm->dig));
+	wm97xx_reg_write(wm, AC97_WM97XX_DIGITISER1, 0);
+	wm97xx_reg_write(wm, AC97_WM97XX_DIGITISER2, WM97XX_PRP_DET_DIG);
+}
+
+static void wm9712_dig_restore(struct wm97xx *wm)
+{
+	wm97xx_reg_write(wm, AC97_WM97XX_DIGITISER1, wm->dig_save[1]);
+	wm97xx_reg_write(wm, AC97_WM97XX_DIGITISER2, wm->dig_save[2]);
+}
+
+static inline int is_pden(struct wm97xx *wm)
+{
+	return wm->dig[2] & WM9712_PDEN;
+}
+
+/*
+ * Read a sample from the WM9712 adc in polling mode.
+ */
+static int wm9712_poll_sample(struct wm97xx *wm, int adcsel, int *sample)
+{
+	int timeout = 5 * delay;
+
+	if (!wm->pen_probably_down) {
+		u16 data = wm97xx_reg_read(wm, AC97_WM97XX_DIGITISER_RD);
+		if (!(data & WM97XX_PEN_DOWN))
+			return RC_PENUP;
+		wm->pen_probably_down = 1;
+	}
+
+	/* set up digitiser */
+	if (adcsel & 0x8000)
+		adcsel = ((adcsel & 0x7fff) + 3) << 12;
+
+	if (wm->mach_ops && wm->mach_ops->pre_sample)
+		wm->mach_ops->pre_sample(adcsel);
+	wm97xx_reg_write(wm, AC97_WM97XX_DIGITISER1,
+			 adcsel | WM97XX_POLL | WM97XX_DELAY(delay));
+
+	/* wait 3 AC97 time slots + delay for conversion */
+	poll_delay(delay);
+
+	/* wait for POLL to go low */
+	while ((wm97xx_reg_read(wm, AC97_WM97XX_DIGITISER1) & WM97XX_POLL)
+	       && timeout) {
+		udelay(AC97_LINK_FRAME);
+		timeout--;
+	}
+
+	if (timeout <= 0) {
+		/* If PDEN is set, we can get a timeout when pen goes up */
+		if (is_pden(wm))
+			wm->pen_probably_down = 0;
+		else
+			dev_dbg(wm->dev, "adc sample timeout");
+		return RC_PENUP;
+	}
+
+	*sample = wm97xx_reg_read(wm, AC97_WM97XX_DIGITISER_RD);
+	if (wm->mach_ops && wm->mach_ops->post_sample)
+		wm->mach_ops->post_sample(adcsel);
+
+	/* check we have correct sample */
+	if ((*sample & WM97XX_ADCSEL_MASK) != adcsel) {
+		dev_dbg(wm->dev, "adc wrong sample, read %x got %x", adcsel,
+		*sample & WM97XX_ADCSEL_MASK);
+		return RC_PENUP;
+	}
+
+	if (!(*sample & WM97XX_PEN_DOWN)) {
+		wm->pen_probably_down = 0;
+		return RC_PENUP;
+	}
+
+	return RC_VALID;
+}
+
+/*
+ * Read a coord from the WM9712 adc in polling mode.
+ */
+static int wm9712_poll_coord(struct wm97xx *wm, struct wm97xx_data *data)
+{
+	int timeout = 5 * delay;
+
+	if (!wm->pen_probably_down) {
+		u16 data_rd = wm97xx_reg_read(wm, AC97_WM97XX_DIGITISER_RD);
+		if (!(data_rd & WM97XX_PEN_DOWN))
+			return RC_PENUP;
+		wm->pen_probably_down = 1;
+	}
+
+	/* set up digitiser */
+	if (wm->mach_ops && wm->mach_ops->pre_sample)
+		wm->mach_ops->pre_sample(WM97XX_ADCSEL_X | WM97XX_ADCSEL_Y);
+
+	wm97xx_reg_write(wm, AC97_WM97XX_DIGITISER1,
+		WM97XX_COO | WM97XX_POLL | WM97XX_DELAY(delay));
+
+	/* wait 3 AC97 time slots + delay for conversion and read x */
+	poll_delay(delay);
+	data->x = wm97xx_reg_read(wm, AC97_WM97XX_DIGITISER_RD);
+	/* wait for POLL to go low */
+	while ((wm97xx_reg_read(wm, AC97_WM97XX_DIGITISER1) & WM97XX_POLL)
+	       && timeout) {
+		udelay(AC97_LINK_FRAME);
+		timeout--;
+	}
+
+	if (timeout <= 0) {
+		/* If PDEN is set, we can get a timeout when pen goes up */
+		if (is_pden(wm))
+			wm->pen_probably_down = 0;
+		else
+			dev_dbg(wm->dev, "adc sample timeout");
+		return RC_PENUP;
+	}
+
+	/* read back y data */
+	data->y = wm97xx_reg_read(wm, AC97_WM97XX_DIGITISER_RD);
+	if (pil)
+		data->p = wm97xx_reg_read(wm, AC97_WM97XX_DIGITISER_RD);
+	else
+		data->p = DEFAULT_PRESSURE;
+
+	if (wm->mach_ops && wm->mach_ops->post_sample)
+		wm->mach_ops->post_sample(WM97XX_ADCSEL_X | WM97XX_ADCSEL_Y);
+
+	/* check we have correct sample */
+	if (!(data->x & WM97XX_ADCSEL_X) || !(data->y & WM97XX_ADCSEL_Y))
+		goto err;
+	if (pil && !(data->p & WM97XX_ADCSEL_PRES))
+		goto err;
+
+	if (!(data->x & WM97XX_PEN_DOWN)) {
+		wm->pen_probably_down = 0;
+		return RC_PENUP;
+	}
+	return RC_VALID;
+err:
+	return RC_PENUP;
+}
+
+/*
+ * Sample the WM9712 touchscreen in polling mode
+ */
+static int wm9712_poll_touch(struct wm97xx *wm, struct wm97xx_data *data)
+{
+	int rc;
+
+	if (coord) {
+		rc = wm9712_poll_coord(wm, data);
+		if (rc != RC_VALID)
+			return rc;
+	} else {
+		rc = wm9712_poll_sample(wm, WM97XX_ADCSEL_X, &data->x);
+		if (rc != RC_VALID)
+			return rc;
+
+		rc = wm9712_poll_sample(wm, WM97XX_ADCSEL_Y, &data->y);
+		if (rc != RC_VALID)
+			return rc;
+
+		if (pil && !five_wire) {
+			rc = wm9712_poll_sample(wm, WM97XX_ADCSEL_PRES,
+						&data->p);
+			if (rc != RC_VALID)
+				return rc;
+		} else
+			data->p = DEFAULT_PRESSURE;
+	}
+	return RC_VALID;
+}
+
+/*
+ * Enable WM9712 continuous mode, i.e. touch data is streamed across
+ * an AC97 slot
+ */
+static int wm9712_acc_enable(struct wm97xx *wm, int enable)
+{
+	u16 dig1, dig2;
+	int ret = 0;
+
+	dig1 = wm->dig[1];
+	dig2 = wm->dig[2];
+
+	if (enable) {
+		/* continous mode */
+		if (wm->mach_ops->acc_startup) {
+			ret = wm->mach_ops->acc_startup(wm);
+			if (ret < 0)
+				return ret;
+		}
+		dig1 &= ~(WM97XX_CM_RATE_MASK | WM97XX_ADCSEL_MASK |
+			WM97XX_DELAY_MASK | WM97XX_SLT_MASK);
+		dig1 |= WM97XX_CTC | WM97XX_COO | WM97XX_SLEN |
+			WM97XX_DELAY(delay) |
+			WM97XX_SLT(wm->acc_slot) |
+			WM97XX_RATE(wm->acc_rate);
+		if (pil)
+			dig1 |= WM97XX_ADCSEL_PRES;
+		dig2 |= WM9712_PDEN;
+	} else {
+		dig1 &= ~(WM97XX_CTC | WM97XX_COO | WM97XX_SLEN);
+		dig2 &= ~WM9712_PDEN;
+		if (wm->mach_ops->acc_shutdown)
+			wm->mach_ops->acc_shutdown(wm);
+	}
+
+	wm97xx_reg_write(wm, AC97_WM97XX_DIGITISER1, dig1);
+	wm97xx_reg_write(wm, AC97_WM97XX_DIGITISER2, dig2);
+	return 0;
+}
+
+struct wm97xx_codec_drv wm9712_codec = {
+	.id = 	WM9712_ID2,
+	.name = "wm9712",
+	.poll_sample = wm9712_poll_sample,
+	.poll_touch = wm9712_poll_touch,
+	.acc_enable = wm9712_acc_enable,
+	.phy_init = wm9712_phy_init,
+	.dig_enable = wm9712_dig_enable,
+	.dig_restore = wm9712_dig_restore,
+	.aux_prepare = wm9712_aux_prepare,
+};
+EXPORT_SYMBOL_GPL(wm9712_codec);
+
+/* Module information */
+MODULE_AUTHOR("Liam Girdwood <[email protected]>");
+MODULE_DESCRIPTION("WM9712 Touch Screen Driver");
+MODULE_LICENSE("GPL");
Signature · 1 line
1.5.3.8
author
#4 lore raw

PATCH 4/6 Add chip driver for WM9713 touchscreen

Cc Dmitry Baryshkov <[email protected]>
Cc Stanley Cai <[email protected]>
Cc Rodolfo Giometti <[email protected]>
Cc Russell King <[email protected]>
Cc Marc Kleine-Budde <[email protected]>
Cc Ian Molton <[email protected]>
Cc Vince Sanders <[email protected]>
Cc Andrew Zabolotny <[email protected]>
---
 drivers/input/touchscreen/wm9713.c |  459 ++++++++++++++++++++++++++++++++++++
 1 files changed, 459 insertions(+), 0 deletions(-)
 create mode 100644 drivers/input/touchscreen/wm9713.c
drivers/input/touchscreen/wm9713.c new file +459 -0
new file mode 100644
index 0000000..5067e59
@@ -0,0 +1,459 @@
+/*
+ * wm9713.c  --  Codec touch driver for Wolfson WM9713 AC97 Codec.
+ *
+ * Copyright 2003, 2004, 2005, 2006, 2007, 2008 Wolfson Microelectronics PLC.
+ * Author: Liam Girdwood
+ *         [email protected] or [email protected]
+ * Parts Copyright : Ian Molton <[email protected]>
+ *                   Andrew Zabolotny <[email protected]>
+ *                   Russell King <[email protected]>
+ *
+ *  This program is free software; you can redistribute  it and/or modify it
+ *  under  the terms of  the GNU General  Public License as published by the
+ *  Free Software Foundation;  either version 2 of the  License, or (at your
+ *  option) any later version.
+ *
+ */
+
+#include <linux/module.h>
+#include <linux/moduleparam.h>
+#include <linux/version.h>
+#include <linux/kernel.h>
+#include <linux/input.h>
+#include <linux/delay.h>
+#include <linux/bitops.h>
+#include <linux/wm97xx.h>
+
+#define TS_NAME			"wm97xx"
+#define WM9713_VERSION		"0.53"
+#define DEFAULT_PRESSURE	0xb0c0
+
+/*
+ * Module parameters
+ */
+
+/*
+ * Set internal pull up for pen detect.
+ *
+ * Pull up is in the range 1.02k (least sensitive) to 64k (most sensitive)
+ * i.e. pull up resistance = 64k Ohms / rpu.
+ *
+ * Adjust this value if you are having problems with pen detect not
+ * detecting any down event.
+ */
+static int rpu = 8;
+module_param(rpu, int, 0);
+MODULE_PARM_DESC(rpu, "Set internal pull up resitor for pen detect.");
+
+/*
+ * Set current used for pressure measurement.
+ *
+ * Set pil = 2 to use 400uA
+ *     pil = 1 to use 200uA and
+ *     pil = 0 to disable pressure measurement.
+ *
+ * This is used to increase the range of values returned by the adc
+ * when measureing touchpanel pressure.
+ */
+static int pil;
+module_param(pil, int, 0);
+MODULE_PARM_DESC(pil, "Set current used for pressure measurement.");
+
+/*
+ * Set threshold for pressure measurement.
+ *
+ * Pen down pressure below threshold is ignored.
+ */
+static int pressure = DEFAULT_PRESSURE & 0xfff;
+module_param(pressure, int, 0);
+MODULE_PARM_DESC(pressure, "Set threshold for pressure measurement.");
+
+/*
+ * Set adc sample delay.
+ *
+ * For accurate touchpanel measurements, some settling time may be
+ * required between the switch matrix applying a voltage across the
+ * touchpanel plate and the ADC sampling the signal.
+ *
+ * This delay can be set by setting delay = n, where n is the array
+ * position of the delay in the array delay_table below.
+ * Long delays > 1ms are supported for completeness, but are not
+ * recommended.
+ */
+static int delay = 4;
+module_param(delay, int, 0);
+MODULE_PARM_DESC(delay, "Set adc sample delay.");
+
+/*
+ * Set adc mask function.
+ *
+ * Sources of glitch noise, such as signals driving an LCD display, may feed
+ * through to the touch screen plates and affect measurement accuracy. In
+ * order to minimise this, a signal may be applied to the MASK pin to delay or
+ * synchronise the sampling.
+ *
+ * 0 = No delay or sync
+ * 1 = High on pin stops conversions
+ * 2 = Edge triggered, edge on pin delays conversion by delay param (above)
+ * 3 = Edge triggered, edge on pin starts conversion after delay param
+ */
+static int mask;
+module_param(mask, int, 0);
+MODULE_PARM_DESC(mask, "Set adc mask function.");
+
+/*
+ * Coordinate Polling Enable.
+ *
+ * Set to 1 to enable coordinate polling. e.g. x,y[,p] is sampled together
+ * for every poll.
+ */
+static int coord;
+module_param(coord, int, 0);
+MODULE_PARM_DESC(coord, "Polling coordinate mode");
+
+/*
+ * ADC sample delay times in uS
+ */
+static const int delay_table[] = {
+	21,    /* 1 AC97 Link frames */
+	42,    /* 2 */
+	84,    /* 4 */
+	167,   /* 8 */
+	333,   /* 16 */
+	667,   /* 32 */
+	1000,  /* 48 */
+	1333,  /* 64 */
+	2000,  /* 96 */
+	2667,  /* 128 */
+	3333,  /* 160 */
+	4000,  /* 192 */
+	4667,  /* 224 */
+	5333,  /* 256 */
+	6000,  /* 288 */
+	0      /* No delay, switch matrix always on */
+};
+
+/*
+ * Delay after issuing a POLL command.
+ *
+ * The delay is 3 AC97 link frames + the touchpanel settling delay
+ */
+static inline void poll_delay(int d)
+{
+	udelay(3 * AC97_LINK_FRAME + delay_table[d]);
+}
+
+/*
+ * set up the physical settings of the WM9713
+ */
+static void wm9713_phy_init(struct wm97xx *wm)
+{
+	u16 dig1 = 0, dig2, dig3;
+
+	/* default values */
+	dig2 = WM97XX_DELAY(4) | WM97XX_SLT(5);
+	dig3 = WM9712_RPU(1);
+
+	/* rpu */
+	if (rpu) {
+		dig3 &= 0xffc0;
+		dig3 |= WM9712_RPU(rpu);
+		dev_info(wm->dev, "setting pen detect pull-up to %d Ohms\n",
+			 64000 / rpu);
+	}
+
+	/* touchpanel pressure */
+	if (pil == 2) {
+		dig3 |= WM9712_PIL;
+		dev_info(wm->dev,
+			 "setting pressure measurement current to 400uA.");
+	} else if (pil)
+		dev_info(wm->dev,
+			 "setting pressure measurement current to 200uA.");
+	if (!pil)
+		pressure = 0;
+
+	/* sample settling delay */
+	if (delay < 0 || delay > 15) {
+		dev_info(wm->dev, "supplied delay out of range.");
+		delay = 4;
+		dev_info(wm->dev, "setting adc sample delay to %d u Secs.",
+			 delay_table[delay]);
+	}
+	dig2 &= 0xff0f;
+	dig2 |= WM97XX_DELAY(delay);
+
+	/* mask */
+	dig3 |= ((mask & 0x3) << 4);
+	if (coord)
+		dig3 |= WM9713_WAIT;
+
+	wm->misc = wm97xx_reg_read(wm, 0x5a);
+
+	wm97xx_reg_write(wm, AC97_WM9713_DIG1, dig1);
+	wm97xx_reg_write(wm, AC97_WM9713_DIG2, dig2);
+	wm97xx_reg_write(wm, AC97_WM9713_DIG3, dig3);
+	wm97xx_reg_write(wm, AC97_GPIO_STICKY, 0x0);
+}
+
+static void wm9713_dig_enable(struct wm97xx *wm, int enable)
+{
+	u16 val;
+
+	if (enable) {
+		val = wm97xx_reg_read(wm, AC97_EXTENDED_MID);
+		wm97xx_reg_write(wm, AC97_EXTENDED_MID, val & 0x7fff);
+		wm97xx_reg_write(wm, AC97_WM9713_DIG3, wm->dig[2] |
+				 WM97XX_PRP_DET_DIG);
+		wm97xx_reg_read(wm, AC97_WM97XX_DIGITISER_RD); /* dummy read */
+	} else {
+		wm97xx_reg_write(wm, AC97_WM9713_DIG3, wm->dig[2] &
+					~WM97XX_PRP_DET_DIG);
+		val = wm97xx_reg_read(wm, AC97_EXTENDED_MID);
+		wm97xx_reg_write(wm, AC97_EXTENDED_MID, val | 0x8000);
+	}
+}
+
+static void wm9713_dig_restore(struct wm97xx *wm)
+{
+	wm97xx_reg_write(wm, AC97_WM9713_DIG1, wm->dig_save[0]);
+	wm97xx_reg_write(wm, AC97_WM9713_DIG2, wm->dig_save[1]);
+	wm97xx_reg_write(wm, AC97_WM9713_DIG3, wm->dig_save[2]);
+}
+
+static void wm9713_aux_prepare(struct wm97xx *wm)
+{
+	memcpy(wm->dig_save, wm->dig, sizeof(wm->dig));
+	wm97xx_reg_write(wm, AC97_WM9713_DIG1, 0);
+	wm97xx_reg_write(wm, AC97_WM9713_DIG2, 0);
+	wm97xx_reg_write(wm, AC97_WM9713_DIG3, WM97XX_PRP_DET_DIG);
+}
+
+static inline int is_pden(struct wm97xx *wm)
+{
+	return wm->dig[2] & WM9713_PDEN;
+}
+
+/*
+ * Read a sample from the WM9713 adc in polling mode.
+ */
+static int wm9713_poll_sample(struct wm97xx *wm, int adcsel, int *sample)
+{
+	u16 dig1;
+	int timeout = 5 * delay;
+
+	if (!wm->pen_probably_down) {
+		u16 data = wm97xx_reg_read(wm, AC97_WM97XX_DIGITISER_RD);
+		if (!(data & WM97XX_PEN_DOWN))
+			return RC_PENUP;
+		wm->pen_probably_down = 1;
+	}
+
+	/* set up digitiser */
+	if (adcsel & 0x8000)
+		adcsel = 1 << ((adcsel & 0x7fff) + 3);
+
+	dig1 = wm97xx_reg_read(wm, AC97_WM9713_DIG1);
+	dig1 &= ~WM9713_ADCSEL_MASK;
+
+	if (wm->mach_ops && wm->mach_ops->pre_sample)
+		wm->mach_ops->pre_sample(adcsel);
+	wm97xx_reg_write(wm, AC97_WM9713_DIG1, dig1 | adcsel | WM9713_POLL);
+
+	/* wait 3 AC97 time slots + delay for conversion */
+	poll_delay(delay);
+
+	/* wait for POLL to go low */
+	while ((wm97xx_reg_read(wm, AC97_WM9713_DIG1) & WM9713_POLL) &&
+		timeout) {
+		udelay(AC97_LINK_FRAME);
+		timeout--;
+	}
+
+	if (timeout <= 0) {
+		/* If PDEN is set, we can get a timeout when pen goes up */
+		if (is_pden(wm))
+			wm->pen_probably_down = 0;
+		else
+			dev_dbg(wm->dev, "adc sample timeout");
+		return RC_PENUP;
+	}
+
+	*sample = wm97xx_reg_read(wm, AC97_WM97XX_DIGITISER_RD);
+	if (wm->mach_ops && wm->mach_ops->post_sample)
+		wm->mach_ops->post_sample(adcsel);
+
+	/* check we have correct sample */
+	if ((*sample & WM97XX_ADCSRC_MASK) != ffs(adcsel >> 1) << 12) {
+		dev_dbg(wm->dev, "adc wrong sample, read %x got %x", adcsel,
+			*sample & WM97XX_ADCSRC_MASK);
+		return RC_PENUP;
+	}
+
+	if (!(*sample & WM97XX_PEN_DOWN)) {
+		wm->pen_probably_down = 0;
+		return RC_PENUP;
+	}
+
+	return RC_VALID;
+}
+
+/*
+ * Read a coordinate from the WM9713 adc in polling mode.
+ */
+static int wm9713_poll_coord(struct wm97xx *wm, struct wm97xx_data *data)
+{
+	u16 dig1;
+	int timeout = 5 * delay;
+
+	if (!wm->pen_probably_down) {
+		u16 data = wm97xx_reg_read(wm, AC97_WM97XX_DIGITISER_RD);
+		if (!(data & WM97XX_PEN_DOWN))
+			return RC_PENUP;
+		wm->pen_probably_down = 1;
+	}
+
+	/* set up digitiser */
+	dig1 = wm97xx_reg_read(wm, AC97_WM9713_DIG1);
+	dig1 &= ~WM9713_ADCSEL_MASK;
+	if (pil)
+		dig1 |= WM97XX_ADCSEL_PRES;
+
+	if (wm->mach_ops && wm->mach_ops->pre_sample)
+		wm->mach_ops->pre_sample(WM97XX_ADCSEL_X | WM97XX_ADCSEL_Y);
+	wm97xx_reg_write(wm, AC97_WM9713_DIG1,
+			 dig1 | WM9713_POLL | WM9713_COO);
+
+	/* wait 3 AC97 time slots + delay for conversion */
+	poll_delay(delay);
+	data->x = wm97xx_reg_read(wm, AC97_WM97XX_DIGITISER_RD);
+	/* wait for POLL to go low */
+	while ((wm97xx_reg_read(wm, AC97_WM9713_DIG1) & WM9713_POLL)
+	       && timeout) {
+		udelay(AC97_LINK_FRAME);
+		timeout--;
+	}
+
+	if (timeout <= 0) {
+		/* If PDEN is set, we can get a timeout when pen goes up */
+		if (is_pden(wm))
+			wm->pen_probably_down = 0;
+		else
+			dev_dbg(wm->dev, "adc sample timeout");
+		return RC_PENUP;
+	}
+
+	/* read back data */
+	data->y = wm97xx_reg_read(wm, AC97_WM97XX_DIGITISER_RD);
+	if (pil)
+		data->p = wm97xx_reg_read(wm, AC97_WM97XX_DIGITISER_RD);
+	else
+		data->p = DEFAULT_PRESSURE;
+
+	if (wm->mach_ops && wm->mach_ops->post_sample)
+		wm->mach_ops->post_sample(WM97XX_ADCSEL_X | WM97XX_ADCSEL_Y);
+
+	/* check we have correct sample */
+	if (!(data->x & WM97XX_ADCSEL_X) || !(data->y & WM97XX_ADCSEL_Y))
+		goto err;
+	if (pil && !(data->p & WM97XX_ADCSEL_PRES))
+		goto err;
+
+	if (!(data->x & WM97XX_PEN_DOWN)) {
+		wm->pen_probably_down = 0;
+		return RC_PENUP;
+	}
+	return RC_VALID;
+err:
+	return RC_PENUP;
+}
+
+/*
+ * Sample the WM9713 touchscreen in polling mode
+ */
+static int wm9713_poll_touch(struct wm97xx *wm, struct wm97xx_data *data)
+{
+	int rc;
+
+	if (coord) {
+		rc = wm9713_poll_coord(wm, data);
+		if (rc != RC_VALID)
+			return rc;
+	} else {
+		rc = wm9713_poll_sample(wm, WM9713_ADCSEL_X, &data->x);
+		if (rc != RC_VALID)
+			return rc;
+		rc = wm9713_poll_sample(wm, WM9713_ADCSEL_Y, &data->y);
+		if (rc != RC_VALID)
+			return rc;
+		if (pil) {
+			rc = wm9713_poll_sample(wm, WM9713_ADCSEL_PRES,
+						&data->p);
+			if (rc != RC_VALID)
+				return rc;
+		} else
+			data->p = DEFAULT_PRESSURE;
+	}
+	return RC_VALID;
+}
+
+/*
+ * Enable WM9713 continuous mode, i.e. touch data is streamed across
+ * an AC97 slot
+ */
+static int wm9713_acc_enable(struct wm97xx *wm, int enable)
+{
+	u16 dig1, dig2, dig3;
+	int ret = 0;
+
+	dig1 = wm->dig[0];
+	dig2 = wm->dig[1];
+	dig3 = wm->dig[2];
+
+	if (enable) {
+		/* continous mode */
+		if (wm->mach_ops->acc_startup &&
+			(ret = wm->mach_ops->acc_startup(wm)) < 0)
+			return ret;
+
+		dig1 &= ~WM9713_ADCSEL_MASK;
+		dig1 |= WM9713_CTC | WM9713_COO | WM9713_ADCSEL_X |
+			WM9713_ADCSEL_Y;
+		if (pil)
+			dig1 |= WM9713_ADCSEL_PRES;
+		dig2 &= ~(WM97XX_DELAY_MASK | WM97XX_SLT_MASK  |
+			WM97XX_CM_RATE_MASK);
+		dig2 |= WM97XX_SLEN | WM97XX_DELAY(delay) |
+		WM97XX_SLT(wm->acc_slot) | WM97XX_RATE(wm->acc_rate);
+		dig3 |= WM9713_PDEN;
+	} else {
+		dig1 &= ~(WM9713_CTC | WM9713_COO);
+		dig2 &= ~WM97XX_SLEN;
+		dig3 &= ~WM9713_PDEN;
+		if (wm->mach_ops->acc_shutdown)
+			wm->mach_ops->acc_shutdown(wm);
+	}
+
+	wm97xx_reg_write(wm, AC97_WM9713_DIG1, dig1);
+	wm97xx_reg_write(wm, AC97_WM9713_DIG2, dig2);
+	wm97xx_reg_write(wm, AC97_WM9713_DIG3, dig3);
+	return ret;
+}
+
+struct wm97xx_codec_drv wm9713_codec = {
+	.id = 	WM9713_ID2,
+	.name = "wm9713",
+	.poll_sample = wm9713_poll_sample,
+	.poll_touch = wm9713_poll_touch,
+	.acc_enable = wm9713_acc_enable,
+	.phy_init = wm9713_phy_init,
+	.dig_enable = wm9713_dig_enable,
+	.dig_restore = wm9713_dig_restore,
+	.aux_prepare = wm9713_aux_prepare,
+};
+EXPORT_SYMBOL_GPL(wm9713_codec);
+
+/* Module information */
+MODULE_AUTHOR("Liam Girdwood <[email protected]>");
+MODULE_DESCRIPTION("WM9713 Touch Screen Driver");
+MODULE_LICENSE("GPL");
Signature · 1 line
1.5.3.8
author
#5 lore raw

PATCH 5/6 Driver for WM97xx touchscreens in streaming mode on Mainstone

Cc Dmitry Baryshkov <[email protected]>
Cc Stanley Cai <[email protected]>
Cc Rodolfo Giometti <[email protected]>
Cc Russell King <[email protected]>
Cc Marc Kleine-Budde <[email protected]>
Cc Ian Molton <[email protected]>
Cc Vince Sanders <[email protected]>
Cc Andrew Zabolotny <[email protected]>
---
 drivers/input/touchscreen/mainstone-wm97xx.c |  298 ++++++++++++++++++++++++++
 1 files changed, 298 insertions(+), 0 deletions(-)
 create mode 100644 drivers/input/touchscreen/mainstone-wm97xx.c
drivers/input/touchscreen/mainstone-wm97xx.c new file +298 -0
new file mode 100644
index 0000000..8e1c35d
@@ -0,0 +1,298 @@
+/*
+ * mainstone-wm97xx.c  --  Mainstone Continuous Touch screen driver for
+ *                         Wolfson WM97xx AC97 Codecs.
+ *
+ * Copyright 2004, 2007 Wolfson Microelectronics PLC.
+ * Author: Liam Girdwood
+ *         [email protected] or [email protected]
+ * Parts Copyright : Ian Molton <[email protected]>
+ *                   Andrew Zabolotny <[email protected]>
+ *
+ *  This program is free software; you can redistribute  it and/or modify it
+ *  under  the terms of  the GNU General  Public License as published by the
+ *  Free Software Foundation;  either version 2 of the  License, or (at your
+ *  option) any later version.
+ *
+ * Notes:
+ *     This is a wm97xx extended touch driver to capture touch
+ *     data in a continuous manner on the Intel XScale archictecture
+ *
+ *  Features:
+ *       - codecs supported:- WM9705, WM9712, WM9713
+ *       - processors supported:- Intel XScale PXA25x, PXA26x, PXA27x
+ *
+ */
+
+#include <linux/module.h>
+#include <linux/moduleparam.h>
+#include <linux/version.h>
+#include <linux/kernel.h>
+#include <linux/init.h>
+#include <linux/delay.h>
+#include <linux/irq.h>
+#include <linux/interrupt.h>
+#include <linux/wm97xx.h>
+#include <linux/io.h>
+#include <asm/arch/pxa-regs.h>
+
+#define VERSION		"0.13"
+
+struct continuous {
+	u16 id;    /* codec id */
+	u8 code;   /* continuous code */
+	u8 reads;  /* number of coord reads per read cycle */
+	u32 speed; /* number of coords per second */
+};
+
+#define WM_READS(sp) ((sp / HZ) + 1)
+
+static const struct continuous cinfo[] = {
+	{WM9705_ID2, 0, WM_READS(94), 94},
+	{WM9705_ID2, 1, WM_READS(188), 188},
+	{WM9705_ID2, 2, WM_READS(375), 375},
+	{WM9705_ID2, 3, WM_READS(750), 750},
+	{WM9712_ID2, 0, WM_READS(94), 94},
+	{WM9712_ID2, 1, WM_READS(188), 188},
+	{WM9712_ID2, 2, WM_READS(375), 375},
+	{WM9712_ID2, 3, WM_READS(750), 750},
+	{WM9713_ID2, 0, WM_READS(94), 94},
+	{WM9713_ID2, 1, WM_READS(120), 120},
+	{WM9713_ID2, 2, WM_READS(154), 154},
+	{WM9713_ID2, 3, WM_READS(188), 188},
+};
+
+/* continuous speed index */
+static int sp_idx;
+static u16 last, tries;
+
+/*
+ * Pen sampling frequency (Hz) in continuous mode.
+ */
+static int cont_rate = 200;
+module_param(cont_rate, int, 0);
+MODULE_PARM_DESC(cont_rate, "Sampling rate in continuous mode (Hz)");
+
+/*
+ * Pen down detection.
+ *
+ * This driver can either poll or use an interrupt to indicate a pen down
+ * event. If the irq request fails then it will fall back to polling mode.
+ */
+static int pen_int;
+module_param(pen_int, int, 0);
+MODULE_PARM_DESC(pen_int, "Pen down detection (1 = interrupt, 0 = polling)");
+
+/*
+ * Pressure readback.
+ *
+ * Set to 1 to read back pen down pressure
+ */
+static int pressure;
+module_param(pressure, int, 0);
+MODULE_PARM_DESC(pressure, "Pressure readback (1 = pressure, 0 = no pressure)");
+
+/*
+ * AC97 touch data slot.
+ *
+ * Touch screen readback data ac97 slot
+ */
+static int ac97_touch_slot = 5;
+module_param(ac97_touch_slot, int, 0);
+MODULE_PARM_DESC(ac97_touch_slot, "Touch screen data slot AC97 number");
+
+
+/* flush AC97 slot 5 FIFO on pxa machines */
+#ifdef CONFIG_PXA27x
+static void wm97xx_acc_pen_up(struct wm97xx *wm)
+{
+	set_current_state(TASK_INTERRUPTIBLE);
+	schedule_timeout(1);
+
+	while (MISR & (1 << 2))
+		MODR;
+}
+#else
+static void wm97xx_acc_pen_up(struct wm97xx *wm)
+{
+	int count = 16;
+	set_current_state(TASK_INTERRUPTIBLE);
+	schedule_timeout(1);
+
+	while (count < 16) {
+		MODR;
+		count--;
+	}
+}
+#endif
+
+static int wm97xx_acc_pen_down(struct wm97xx *wm)
+{
+	u16 x, y, p = 0x100 | WM97XX_ADCSEL_PRES;
+	int reads = 0;
+
+	/* data is never immediately available after pen down irq */
+	set_current_state(TASK_INTERRUPTIBLE);
+	schedule_timeout(1);
+
+	if (tries > 5) {
+		tries = 0;
+		return RC_PENUP;
+	}
+
+	x = MODR;
+	if (x == last) {
+		tries++;
+		return RC_AGAIN;
+	}
+	last = x;
+	do {
+		if (reads)
+			x = MODR;
+		y = MODR;
+		if (pressure)
+			p = MODR;
+
+		/* are samples valid */
+		if ((x & 0x7000) != WM97XX_ADCSEL_X ||
+			(y & 0x7000) != WM97XX_ADCSEL_Y ||
+			(p & 0x7000) != WM97XX_ADCSEL_PRES)
+			goto up;
+
+		/* coordinate is good */
+		tries = 0;
+		input_report_abs(wm->input_dev, ABS_X, x & 0xfff);
+		input_report_abs(wm->input_dev, ABS_Y, y & 0xfff);
+		input_report_abs(wm->input_dev, ABS_PRESSURE, p & 0xfff);
+		input_sync(wm->input_dev);
+		reads++;
+	} while (reads < cinfo[sp_idx].reads);
+up:
+	return RC_PENDOWN | RC_AGAIN;
+}
+
+static int wm97xx_acc_startup(struct wm97xx *wm)
+{
+	int idx = 0;
+
+	/* check we have a codec */
+	if (wm->ac97 == NULL)
+		return -ENODEV;
+
+	/* Go you big red fire engine */
+	for (idx = 0; idx < ARRAY_SIZE(cinfo); idx++) {
+		if (wm->id != cinfo[idx].id)
+			continue;
+		sp_idx = idx;
+		if (cont_rate <= cinfo[idx].speed)
+			break;
+	}
+	wm->acc_rate = cinfo[sp_idx].code;
+	wm->acc_slot = ac97_touch_slot;
+	dev_info(wm->dev,
+		 "mainstone accelerated touchscreen driver, %d samples/sec\n",
+		 cinfo[sp_idx].speed);
+
+	/* codec specific irq config */
+	if (pen_int) {
+		switch (wm->id) {
+		case WM9705_ID2:
+			wm->pen_irq = IRQ_GPIO(4);
+			set_irq_type(IRQ_GPIO(4), IRQT_BOTHEDGE);
+			break;
+		case WM9712_ID2:
+		case WM9713_ID2:
+			/* enable pen down interrupt */
+			/* use PEN_DOWN GPIO 13 to assert IRQ on GPIO line 2 */
+			wm->pen_irq = MAINSTONE_AC97_IRQ;
+			wm97xx_config_gpio(wm, WM97XX_GPIO_13, WM97XX_GPIO_IN,
+					   WM97XX_GPIO_POL_HIGH,
+					   WM97XX_GPIO_STICKY,
+					   WM97XX_GPIO_WAKE);
+			wm97xx_config_gpio(wm, WM97XX_GPIO_2, WM97XX_GPIO_OUT,
+					   WM97XX_GPIO_POL_HIGH,
+					   WM97XX_GPIO_NOTSTICKY,
+					   WM97XX_GPIO_NOWAKE);
+			break;
+		default:
+			dev_err(wm->dev,
+				"pen down irq not supported on this device\n");
+			pen_int = 0;
+			break;
+		}
+	}
+
+	return 0;
+}
+
+static void wm97xx_acc_shutdown(struct wm97xx *wm)
+{
+	/* codec specific deconfig */
+	if (pen_int) {
+		switch (wm->id & 0xffff) {
+		case WM9705_ID2:
+			wm->pen_irq = 0;
+			break;
+		case WM9712_ID2:
+		case WM9713_ID2:
+			/* disable interrupt */
+			wm->pen_irq = 0;
+			break;
+		}
+	}
+}
+
+static void wm97xx_irq_enable(struct wm97xx *wm, int enable)
+{
+	if (enable)
+		enable_irq(wm->pen_irq);
+	else
+		disable_irq(wm->pen_irq);
+}
+
+static struct wm97xx_mach_ops mainstone_mach_ops = {
+	.acc_enabled = 1,
+	.acc_pen_up = wm97xx_acc_pen_up,
+	.acc_pen_down = wm97xx_acc_pen_down,
+	.acc_startup = wm97xx_acc_startup,
+	.acc_shutdown = wm97xx_acc_shutdown,
+	.irq_enable = wm97xx_irq_enable,
+};
+
+static int mainstone_wm97xx_probe(struct platform_device *pdev)
+{
+	struct wm97xx *wm = platform_get_drvdata(pdev);
+	return wm97xx_register_mach_ops(wm, &mainstone_mach_ops);
+}
+
+static int mainstone_wm97xx_remove(struct platform_device *pdev)
+{
+	struct wm97xx *wm = platform_get_drvdata(pdev);
+	wm97xx_unregister_mach_ops(wm);
+	return 0;
+}
+
+static struct platform_driver mainstone_wm97xx_driver = {
+	.probe = mainstone_wm97xx_probe,
+	.remove = mainstone_wm97xx_remove,
+	.driver = {
+		.name = "wm97xx-touch",
+	},
+};
+
+static int __init mainstone_wm97xx_init(void)
+{
+	return platform_driver_register(&mainstone_wm97xx_driver);
+}
+
+static void __exit mainstone_wm97xx_exit(void)
+{
+	platform_driver_unregister(&mainstone_wm97xx_driver);
+}
+
+module_init(mainstone_wm97xx_init);
+module_exit(mainstone_wm97xx_exit);
+
+/* Module information */
+MODULE_AUTHOR("Liam Girdwood <[email protected]>");
+MODULE_DESCRIPTION("wm97xx continuous touch driver for mainstone");
+MODULE_LICENSE("GPL");
Signature · 1 line
1.5.3.8
author
#6 lore raw

PATCH 6/6 Build system and MAINTAINERS entry for WM97xx touchscreen drivers

---
 MAINTAINERS                        |   10 +++++++
 drivers/input/touchscreen/Kconfig  |   52 ++++++++++++++++++++++++++++++++++++
 drivers/input/touchscreen/Makefile |    7 +++++
 3 files changed, 69 insertions(+), 0 deletions(-)
MAINTAINERS +10 -0
index 2340cfb..f02851c 100644
@@ -4204,6 +4204,16 @@ L:	[email protected]
 W:	http://oops.ghostprotocols.net:81/blog
 S:	Maintained
 
+WM97XX TOUCHSCREEN DRIVERS
+P:	Mark Brown
+M:	[email protected]
+P:	Liam Girdwood
+M:	[email protected]
+L:	[email protected]
+T:	git git://opensource.wolfsonmicro.com/linux-2.6-touch
+W:	http://opensource.wolfsonmicro.com/node/7
+S:	Supported
+
 X.25 NETWORK LAYER
 P:	Henner Eisen
 M:	[email protected]
drivers/input/touchscreen/Kconfig +52 -0

58 lines not on this page · raw message

drivers/input/touchscreen/Makefile +7 -0
index 35d4097..d38156e 100644
@@ -4,6 +4,8 @@
 
 # Each configuration option enables a list of files.
 
+wm97xx-ts-y := wm97xx-core.o
+
 obj-$(CONFIG_TOUCHSCREEN_ADS7846)	+= ads7846.o
 obj-$(CONFIG_TOUCHSCREEN_BITSY)		+= h3600_ts_input.o
 obj-$(CONFIG_TOUCHSCREEN_CORGI)		+= corgi_ts.o
@@ -19,3 +21,8 @@ obj-$(CONFIG_TOUCHSCREEN_PENMOUNT)	+= penmount.o
 obj-$(CONFIG_TOUCHSCREEN_TOUCHRIGHT)	+= touchright.o
 obj-$(CONFIG_TOUCHSCREEN_TOUCHWIN)	+= touchwin.o
 obj-$(CONFIG_TOUCHSCREEN_UCB1400)	+= ucb1400_ts.o
+obj-$(CONFIG_TOUCHSCREEN_WM97XX)	+= wm97xx-ts.o
+obj-$(CONFIG_TOUCHSCREEN_WM97XX_MAINSTONE)	+= mainstone-wm97xx.o
+wm97xx-ts-$(CONFIG_TOUCHSCREEN_WM9705)  += wm9705.o
+wm97xx-ts-$(CONFIG_TOUCHSCREEN_WM9712)  += wm9712.o
+wm97xx-ts-$(CONFIG_TOUCHSCREEN_WM9713)  += wm9713.o
Signature · 1 line
1.5.3.8
maintainer
#7 lore raw

Re: [PATCH 1/6] Core driver for WM97xx touchscreens

In reply to Mark Brown

Hi Mark,

Quoted 5 lines · Mark Brown
drivers/input/touchscreen/wm97xx-core.c new file +5 -0
+
+	/* register our battery device */
+	wm->battery_dev = platform_device_alloc("wm97xx-battery", 0);
+	if (!wm->battery_dev)
+		goto batt_err;

...

drivers/input/touchscreen/wm97xx-core.c line 627

Quoted 5 lines

+ batt_err:

drivers/input/touchscreen/wm97xx-core.c new file +4 -0
+	input_unregister_device(wm->input_dev);
+	kfree(wm);
+	return ret;
+}

The probe error handling is not quite correct. When we reach the fragment above ret variable is 0 so if platfrom_device_alloc() fails we will return 0 and the device will be considered bound but in half-dead state. Please make sure that proper error is returned in all cases. Also please do not mix out of line and in-line error unwinding (input_free_device() should be called in the error path and if you are concerned about double-free after input_unregister_device() just set wm->input_dev to NULL there).

Thanks.

Signature · 1 line
Dmitry
author
#8 lore raw

Re: [PATCH 1/6] Core driver for WM97xx touchscreens

Quoted 7 lines · Dmitry Torokhov

The probe error handling is not quite correct. When we reach the fragment above ret variable is 0 so if platfrom_device_alloc() fails we will return 0 and the device will be considered bound but in half-dead state. Please make sure that proper error is returned in all cases. Also please do not mix out of line and in-line error unwinding (input_free_device() should be called in the error path and if you are concerned about double-free after input_unregister_device() just set wm->input_dev to NULL there).

Thanks for the review, I've implemented these changes and will resubmit as a followup to this e-mail, also including a change from Dmitry Baryshkov to make the devices unnumbered.

author
#9 lore raw

PATCH 1/1 Core driver for WM97xx touchscreens

This patch series adds support for the touchscreen controllers provided by Wolfson Microelectronics WM97xx series chips in both polled and streaming modes.

These drivers have been maintained out of tree since 2003. During that time the driver the primary maintainer was Liam Girdwood and a number of people have made contributions including Stanley Cai, Rodolfo Giometti, Russell King, Marc Kleine-Budde, Ian Molton, Vincent Sanders, Andrew Zabolotny, Graeme Gregory, Mike Arthur and myself. Apologies to anyone I have omitted.

Cc Dmitry Baryshkov <[email protected]>
Cc Stanley Cai <[email protected]>
Cc Rodolfo Giometti <[email protected]>
Cc Russell King <[email protected]>
Cc Marc Kleine-Budde <[email protected]>
Cc Ian Molton <[email protected]>
Cc Vincent Sanders <[email protected]>
Cc Andrew Zabolotny <[email protected]>
---
 drivers/input/touchscreen/wm97xx-core.c |  732 +++++++++++++++++++++++++++++++
 include/linux/wm97xx.h                  |  309 +++++++++++++
 2 files changed, 1041 insertions(+), 0 deletions(-)
 create mode 100644 drivers/input/touchscreen/wm97xx-core.c
 create mode 100644 include/linux/wm97xx.h
drivers/input/touchscreen/wm97xx-core.c new file +732 -0
new file mode 100644
index 0000000..44cf033
@@ -0,0 +1,732 @@
+/*
+ * wm97xx-core.c  --  Touch screen driver core for Wolfson WM9705, WM9712
+ *                    and WM9713 AC97 Codecs.
+ *
+ * Copyright 2003, 2004, 2005, 2006, 2007, 2008 Wolfson Microelectronics PLC.
+ * Author: Liam Girdwood
+ *         [email protected] or [email protected]
+ * Parts Copyright : Ian Molton <[email protected]>
+ *                   Andrew Zabolotny <[email protected]>
+ *                   Russell King <[email protected]>
+ *
+ *  This program is free software; you can redistribute  it and/or modify it
+ *  under  the terms of  the GNU General  Public License as published by the
+ *  Free Software Foundation;  either version 2 of the  License, or (at your
+ *  option) any later version.
+ *
+ * Notes:
+ *
+ *  Features:
+ *       - supports WM9705, WM9712, WM9713
+ *       - polling mode
+ *       - continuous mode (arch-dependent)
+ *       - adjustable rpu/dpp settings
+ *       - adjustable pressure current
+ *       - adjustable sample settle delay
+ *       - 4 and 5 wire touchscreens (5 wire is WM9712 only)
+ *       - pen down detection
+ *       - battery monitor
+ *       - sample AUX adcs
+ *       - power management
+ *       - codec GPIO
+ *       - codec event notification
+ * Todo
+ *       - Support for async sampling control for noisy LCDs.
+ *
+ */
+
+#include <linux/module.h>
+#include <linux/moduleparam.h>
+#include <linux/version.h>
+#include <linux/kernel.h>
+#include <linux/init.h>
+#include <linux/delay.h>
+#include <linux/string.h>
+#include <linux/proc_fs.h>
+#include <linux/pm.h>
+#include <linux/interrupt.h>
+#include <linux/bitops.h>
+#include <linux/workqueue.h>
+#include <linux/wm97xx.h>
+#include <linux/uaccess.h>
+#include <linux/io.h>
+
+#define TS_NAME			"wm97xx"
+#define WM_CORE_VERSION		"0.65"
+#define DEFAULT_PRESSURE	0xb0c0
+
+
+/*
+ * Touchscreen absolute values
+ *
+ * These parameters are used to help the input layer discard out of
+ * range readings and reduce jitter etc.
+ *
+ *   o min, max:- indicate the min and max values your touch screen returns
+ *   o fuzz:- use a higher number to reduce jitter
+ *
+ * The default values correspond to Mainstone II in QVGA mode
+ *
+ * Please read
+ * Documentation/input/input-programming.txt for more details.
+ */
+
+static int abs_x[3] = {350, 3900, 5};
+module_param_array(abs_x, int, NULL, 0);
+MODULE_PARM_DESC(abs_x, "Touchscreen absolute X min, max, fuzz");
+
+static int abs_y[3] = {320, 3750, 40};
+module_param_array(abs_y, int, NULL, 0);
+MODULE_PARM_DESC(abs_y, "Touchscreen absolute Y min, max, fuzz");
+
+static int abs_p[3] = {0, 150, 4};
+module_param_array(abs_p, int, NULL, 0);
+MODULE_PARM_DESC(abs_p, "Touchscreen absolute Pressure min, max, fuzz");
+
+/*
+ * wm97xx IO access, all IO locking done by AC97 layer
+ */
+int wm97xx_reg_read(struct wm97xx *wm, u16 reg)
+{
+	if (wm->ac97)
+		return wm->ac97->bus->ops->read(wm->ac97, reg);
+	else
+		return -1;
+}
+EXPORT_SYMBOL_GPL(wm97xx_reg_read);
+
+void wm97xx_reg_write(struct wm97xx *wm, u16 reg, u16 val)
+{
+	/* cache digitiser registers */
+	if (reg >= AC97_WM9713_DIG1 && reg <= AC97_WM9713_DIG3)
+		wm->dig[(reg - AC97_WM9713_DIG1) >> 1] = val;
+
+	/* cache gpio regs */
+	if (reg >= AC97_GPIO_CFG && reg <= AC97_MISC_AFE)
+		wm->gpio[(reg - AC97_GPIO_CFG) >> 1] = val;
+
+	/* wm9713 irq reg */
+	if (reg == 0x5a)
+		wm->misc = val;
+
+	if (wm->ac97)
+		wm->ac97->bus->ops->write(wm->ac97, reg, val);
+}
+EXPORT_SYMBOL_GPL(wm97xx_reg_write);
+
+/**
+ *	wm97xx_read_aux_adc - Read the aux adc.
+ *	@wm: wm97xx device.
+ *  @adcsel: codec ADC to be read
+ *
+ *	Reads the selected AUX ADC.
+ */
+
+int wm97xx_read_aux_adc(struct wm97xx *wm, u16 adcsel)
+{
+	int power_adc = 0, auxval;
+	u16 power = 0;
+
+	/* get codec */
+	mutex_lock(&wm->codec_mutex);
+
+	/* When the touchscreen is not in use, we may have to power up
+	 * the AUX ADC before we can use sample the AUX inputs->
+	 */
+	if (wm->id == WM9713_ID2 &&
+	    (power = wm97xx_reg_read(wm, AC97_EXTENDED_MID)) & 0x8000) {
+		power_adc = 1;
+		wm97xx_reg_write(wm, AC97_EXTENDED_MID, power & 0x7fff);
+	}
+
+	/* Prepare the codec for AUX reading */
+	wm->codec->aux_prepare(wm);
+
+	/* Turn polling mode on to read AUX ADC */
+	wm->pen_probably_down = 1;
+	wm->codec->poll_sample(wm, adcsel, &auxval);
+
+	if (power_adc)
+		wm97xx_reg_write(wm, AC97_EXTENDED_MID, power | 0x8000);
+
+	wm->codec->dig_restore(wm);
+
+	wm->pen_probably_down = 0;
+
+	mutex_unlock(&wm->codec_mutex);
+	return auxval & 0xfff;
+}
+EXPORT_SYMBOL_GPL(wm97xx_read_aux_adc);
+
+/**
+ *	wm97xx_get_gpio - Get the status of a codec GPIO.
+ *	@wm: wm97xx device.
+ *      @gpio: gpio
+ *
+ *	Get the status of a codec GPIO pin
+ */
+
+enum wm97xx_gpio_status wm97xx_get_gpio(struct wm97xx *wm, u32 gpio)
+{
+	u16 status;
+	enum wm97xx_gpio_status ret;
+
+	mutex_lock(&wm->codec_mutex);
+	status = wm97xx_reg_read(wm, AC97_GPIO_STATUS);
+
+	if (status & gpio)
+		ret = WM97XX_GPIO_HIGH;
+	else
+		ret = WM97XX_GPIO_LOW;
+
+	mutex_unlock(&wm->codec_mutex);
+	return ret;
+}
+EXPORT_SYMBOL_GPL(wm97xx_get_gpio);
+
+/**
+ *	wm97xx_set_gpio - Set the status of a codec GPIO.
+ *	@wm: wm97xx device.
+ *  @gpio: gpio
+ *
+ *
+ *	Set the status of a codec GPIO pin
+ */
+
+void wm97xx_set_gpio(struct wm97xx *wm, u32 gpio,
+				enum wm97xx_gpio_status status)
+{
+	u16 reg;
+
+	mutex_lock(&wm->codec_mutex);
+	reg = wm97xx_reg_read(wm, AC97_GPIO_STATUS);
+
+	if (status & WM97XX_GPIO_HIGH)
+		reg |= gpio;
+	else
+		reg &= ~gpio;
+
+	if (wm->id == WM9712_ID2)
+		wm97xx_reg_write(wm, AC97_GPIO_STATUS, reg << 1);
+	else
+		wm97xx_reg_write(wm, AC97_GPIO_STATUS, reg);
+	mutex_unlock(&wm->codec_mutex);
+}
+EXPORT_SYMBOL_GPL(wm97xx_set_gpio);
+
+/*
+ * Codec GPIO pin configuration, this sets pin direction, polarity,
+ * stickyness and wake up.
+ */
+void wm97xx_config_gpio(struct wm97xx *wm, u32 gpio, enum wm97xx_gpio_dir dir,
+		   enum wm97xx_gpio_pol pol, enum wm97xx_gpio_sticky sticky,
+		   enum wm97xx_gpio_wake wake)
+{
+	u16 reg;
+
+	mutex_lock(&wm->codec_mutex);
+	reg = wm97xx_reg_read(wm, AC97_GPIO_POLARITY);
+
+	if (pol == WM97XX_GPIO_POL_HIGH)
+		reg |= gpio;
+	else
+		reg &= ~gpio;
+
+	wm97xx_reg_write(wm, AC97_GPIO_POLARITY, reg);
+	reg = wm97xx_reg_read(wm, AC97_GPIO_STICKY);
+
+	if (sticky == WM97XX_GPIO_STICKY)
+		reg |= gpio;
+	else
+		reg &= ~gpio;
+
+	wm97xx_reg_write(wm, AC97_GPIO_STICKY, reg);
+	reg = wm97xx_reg_read(wm, AC97_GPIO_WAKEUP);
+
+	if (wake == WM97XX_GPIO_WAKE)
+		reg |= gpio;
+	else
+		reg &= ~gpio;
+
+	wm97xx_reg_write(wm, AC97_GPIO_WAKEUP, reg);
+	reg = wm97xx_reg_read(wm, AC97_GPIO_CFG);
+
+	if (dir == WM97XX_GPIO_IN)
+		reg |= gpio;
+	else
+		reg &= ~gpio;
+
+	wm97xx_reg_write(wm, AC97_GPIO_CFG, reg);
+	mutex_unlock(&wm->codec_mutex);
+}
+EXPORT_SYMBOL_GPL(wm97xx_config_gpio);
+
+/*
+ * Handle a pen down interrupt.
+ */
+static void wm97xx_pen_irq_worker(struct work_struct *work)
+{
+	struct wm97xx *wm = container_of(work, struct wm97xx, pen_event_work);
+
+	/* do we need to enable the touch panel reader */
+	if (wm->id == WM9705_ID2) {
+		if (wm97xx_reg_read(wm, AC97_WM97XX_DIGITISER_RD) &
+					WM97XX_PEN_DOWN)
+			wm->pen_is_down = 1;
+		else
+			wm->pen_is_down = 0;
+	} else {
+		u16 status, pol;
+		mutex_lock(&wm->codec_mutex);
+		status = wm97xx_reg_read(wm, AC97_GPIO_STATUS);
+		pol = wm97xx_reg_read(wm, AC97_GPIO_POLARITY);
+
+		if (WM97XX_GPIO_13 & pol & status) {
+			wm->pen_is_down = 1;
+			wm97xx_reg_write(wm, AC97_GPIO_POLARITY, pol &
+						~WM97XX_GPIO_13);
+		} else {
+			wm->pen_is_down = 0;
+			wm97xx_reg_write(wm, AC97_GPIO_POLARITY, pol |
+					 WM97XX_GPIO_13);
+		}
+
+		if (wm->id == WM9712_ID2)
+			wm97xx_reg_write(wm, AC97_GPIO_STATUS, (status &
+						~WM97XX_GPIO_13) << 1);
+		else
+			wm97xx_reg_write(wm, AC97_GPIO_STATUS, status &
+						~WM97XX_GPIO_13);
+		mutex_unlock(&wm->codec_mutex);
+	}
+
+	queue_delayed_work(wm->ts_workq, &wm->ts_reader, 0);
+
+	if (!wm->pen_is_down && wm->mach_ops && wm->mach_ops->acc_enabled)
+		wm->mach_ops->acc_pen_up(wm);
+	wm->mach_ops->irq_enable(wm, 1);
+}
+
+/*
+ * Codec PENDOWN irq handler
+ *
+ * We have to disable the codec interrupt in the handler because it can
+ * take upto 1ms to clear the interrupt source. The interrupt is then enabled
+ * again in the slow handler when the source has been cleared.
+ */
+static irqreturn_t wm97xx_pen_interrupt(int irq, void *dev_id)
+{
+	struct wm97xx *wm = dev_id;
+	wm->mach_ops->irq_enable(wm, 0);
+	queue_work(wm->ts_workq, &wm->pen_event_work);
+	return IRQ_HANDLED;
+}
+
+/*
+ * initialise pen IRQ handler and workqueue
+ */
+static int wm97xx_init_pen_irq(struct wm97xx *wm)
+{
+	u16 reg;
+
+	/* If an interrupt is supplied an IRQ enable operation must also be
+	 * provided. */
+	BUG_ON(!wm->mach_ops->irq_enable);
+
+	INIT_WORK(&wm->pen_event_work, wm97xx_pen_irq_worker);
+
+	if (request_irq(wm->pen_irq, wm97xx_pen_interrupt, IRQF_SHARED,
+			"wm97xx-pen", wm)) {
+		dev_err(wm->dev,
+			"Failed to register pen down interrupt, polling");
+		wm->pen_irq = 0;
+		return -EINVAL;
+	}
+
+	/* enable PEN down on wm9712/13 */
+	if (wm->id != WM9705_ID2) {
+		reg = wm97xx_reg_read(wm, AC97_MISC_AFE);
+		wm97xx_reg_write(wm, AC97_MISC_AFE, reg & 0xfffb);
+		reg = wm97xx_reg_read(wm, 0x5a);
+		wm97xx_reg_write(wm, 0x5a, reg & ~0x0001);
+	}
+
+	return 0;
+}
+
+static int wm97xx_read_samples(struct wm97xx *wm)
+{
+	struct wm97xx_data data;
+	int rc;
+
+	mutex_lock(&wm->codec_mutex);
+
+	if (wm->mach_ops && wm->mach_ops->acc_enabled)
+		rc = wm->mach_ops->acc_pen_down(wm);
+	else
+		rc = wm->codec->poll_touch(wm, &data);
+
+	if (rc & RC_PENUP) {
+		if (wm->pen_is_down) {
+			wm->pen_is_down = 0;
+			dev_dbg(wm->dev, "pen up\n");
+			input_report_abs(wm->input_dev, ABS_PRESSURE, 0);
+			input_sync(wm->input_dev);
+		} else if (!(rc & RC_AGAIN)) {
+			/* We need high frequency updates only while
+			* pen is down, the user never will be able to
+			* touch screen faster than a few times per
+			* second... On the other hand, when the user
+			* is actively working with the touchscreen we
+			* don't want to lose the quick response. So we
+			* will slowly increase sleep time after the
+			* pen is up and quicky restore it to ~one task
+			* switch when pen is down again.
+			*/
+			if (wm->ts_reader_interval < HZ / 10)
+				wm->ts_reader_interval++;
+		}
+
+	} else if (rc & RC_VALID) {
+		dev_dbg(wm->dev,
+			"pen down: x=%x:%d, y=%x:%d, pressure=%x:%d\n",
+			data.x >> 12, data.x & 0xfff, data.y >> 12,
+			data.y & 0xfff, data.p >> 12, data.p & 0xfff);
+		input_report_abs(wm->input_dev, ABS_X, data.x & 0xfff);
+		input_report_abs(wm->input_dev, ABS_Y, data.y & 0xfff);
+		input_report_abs(wm->input_dev, ABS_PRESSURE, data.p & 0xfff);
+		input_sync(wm->input_dev);
+		wm->pen_is_down = 1;
+		wm->ts_reader_interval = wm->ts_reader_min_interval;
+	} else if (rc & RC_PENDOWN) {
+		dev_dbg(wm->dev, "pen down");
+		wm->pen_is_down = 1;
+		wm->ts_reader_interval = wm->ts_reader_min_interval;
+	}
+
+	mutex_unlock(&wm->codec_mutex);
+	return rc;
+}
+
+/*
+* The touchscreen sample reader.
+*/
+static void wm97xx_ts_reader(struct work_struct *work)
+{
+	int rc;
+	struct wm97xx *wm = container_of(work, struct wm97xx, ts_reader.work);
+
+	BUG_ON(!wm->codec);
+
+	do {
+		rc = wm97xx_read_samples(wm);
+	} while (rc & RC_AGAIN);
+
+	if (wm->pen_is_down || !wm->pen_irq)
+		queue_delayed_work(wm->ts_workq, &wm->ts_reader,
+				   wm->ts_reader_interval);
+}
+
+/**
+ *	wm97xx_ts_input_open - Open the touch screen input device.
+ *	@idev:	Input device to be opened.
+ *
+ *	Called by the input sub system to open a wm97xx touchscreen device.
+ *  Starts the touchscreen thread and touch digitiser.
+ */
+static int wm97xx_ts_input_open(struct input_dev *idev)
+{
+	struct wm97xx *wm = input_get_drvdata(idev);
+
+	wm->ts_workq = create_singlethread_workqueue("kwm97xx");
+	if (wm->ts_workq == NULL) {
+		dev_err(wm->dev,
+			"Failed to create workqueue\n");
+		return -EINVAL;
+	}
+
+	/* start digitiser */
+	if (wm->mach_ops && wm->mach_ops->acc_enabled)
+		wm->codec->acc_enable(wm, 1);
+	wm->codec->dig_enable(wm, 1);
+
+	INIT_DELAYED_WORK(&wm->ts_reader, wm97xx_ts_reader);
+
+	wm->ts_reader_min_interval = HZ >= 100 ? HZ / 100 : 1;
+	if (wm->ts_reader_min_interval < 1)
+		wm->ts_reader_min_interval = 1;
+	wm->ts_reader_interval = wm->ts_reader_min_interval;
+
+	wm->pen_is_down = 0;
+	if (wm->pen_irq)
+		wm97xx_init_pen_irq(wm);
+	else
+		dev_err(wm->dev, "No IRQ specified\n");
+
+	/* If we either don't have an interrupt for pen down events or
+	 * failed to acquire it then we need to poll.
+	 */
+	if (wm->pen_irq == 0)
+		queue_delayed_work(wm->ts_workq, &wm->ts_reader,
+				   wm->ts_reader_interval);
+
+	return 0;
+}
+
+/**
+ *	wm97xx_ts_input_close - Close the touch screen input device.
+ *	@idev:	Input device to be closed.
+ *
+ *	Called by the input sub system to close a wm97xx touchscreen device.
+ *  Kills the touchscreen thread and stops the touch digitiser.
+ */
+
+static void wm97xx_ts_input_close(struct input_dev *idev)
+{
+	struct wm97xx *wm = input_get_drvdata(idev);
+
+	if (wm->pen_irq)
+		free_irq(wm->pen_irq, wm);
+
+	wm->pen_is_down = 0;
+
+	/* ts_reader rearms itself so we need to explicitly stop it
+	 * before we destroy the workqueue.
+	 */
+	cancel_delayed_work_sync(&wm->ts_reader);
+	destroy_workqueue(wm->ts_workq);
+
+	/* stop digitiser */
+	wm->codec->dig_enable(wm, 0);
+	if (wm->mach_ops && wm->mach_ops->acc_enabled)
+		wm->codec->acc_enable(wm, 0);
+}
+
+static int wm97xx_probe(struct device *dev)
+{
+	struct wm97xx *wm;
+	int ret = 0, id = 0;
+
+	wm = kzalloc(sizeof(struct wm97xx), GFP_KERNEL);
+	if (!wm)
+		return -ENOMEM;
+	mutex_init(&wm->codec_mutex);
+
+	wm->dev = dev;
+	dev->driver_data = wm;
+	wm->ac97 = to_ac97_t(dev);
+
+	/* check that we have a supported codec */
+	id = wm97xx_reg_read(wm, AC97_VENDOR_ID1);
+	if (id != WM97XX_ID1) {
+		dev_err(dev, "Device with vendor %04x is not a wm97xx\n", id);
+		ret = -ENODEV;
+		goto alloc_err;
+	}
+
+	wm->id = wm97xx_reg_read(wm, AC97_VENDOR_ID2);
+
+	dev_info(wm->dev, "detected a wm97%02x codec", wm->id & 0xff);
+
+	switch (wm->id & 0xff) {
+#ifdef CONFIG_TOUCHSCREEN_WM9705
+	case 0x05:
+		wm->codec = &wm9705_codec;
+		break;
+#endif
+#ifdef CONFIG_TOUCHSCREEN_WM9712
+	case 0x12:
+		wm->codec = &wm9712_codec;
+		break;
+#endif
+#ifdef CONFIG_TOUCHSCREEN_WM9713
+	case 0x13:
+		wm->codec = &wm9713_codec;
+		break;
+#endif
+	default:
+		dev_err(wm->dev, "Support for wm97%02x not compiled in.\n",
+			wm->id & 0xff);
+		ret = -ENODEV;
+		goto alloc_err;
+	}
+
+	wm->input_dev = input_allocate_device();
+	if (wm->input_dev == NULL) {
+		ret = -ENOMEM;
+		goto alloc_err;
+	}
+
+	/* set up touch configuration */
+	wm->input_dev->name = "wm97xx touchscreen";
+	wm->input_dev->open = wm97xx_ts_input_open;
+	wm->input_dev->close = wm97xx_ts_input_close;
+	set_bit(EV_ABS, wm->input_dev->evbit);
+	set_bit(ABS_X, wm->input_dev->absbit);
+	set_bit(ABS_Y, wm->input_dev->absbit);
+	set_bit(ABS_PRESSURE, wm->input_dev->absbit);
+	input_set_abs_params(wm->input_dev, ABS_X, abs_x[0], abs_x[1],
+			     abs_x[2], 0);
+	input_set_abs_params(wm->input_dev, ABS_Y, abs_y[0], abs_y[1],
+			     abs_y[2], 0);
+	input_set_abs_params(wm->input_dev, ABS_PRESSURE, abs_p[0], abs_p[1],
+			     abs_p[2], 0);
+	input_set_drvdata(wm->input_dev, wm);
+	wm->input_dev->dev.parent = dev;
+	ret = input_register_device(wm->input_dev);
+	if (ret < 0) {
+		goto dev_alloc_err;
+	}
+
+	/* set up physical characteristics */
+	wm->codec->phy_init(wm);
+
+	/* load gpio cache */
+	wm->gpio[0] = wm97xx_reg_read(wm, AC97_GPIO_CFG);
+	wm->gpio[1] = wm97xx_reg_read(wm, AC97_GPIO_POLARITY);
+	wm->gpio[2] = wm97xx_reg_read(wm, AC97_GPIO_STICKY);
+	wm->gpio[3] = wm97xx_reg_read(wm, AC97_GPIO_WAKEUP);
+	wm->gpio[4] = wm97xx_reg_read(wm, AC97_GPIO_STATUS);
+	wm->gpio[5] = wm97xx_reg_read(wm, AC97_MISC_AFE);
+
+	/* register our battery device */
+	wm->battery_dev = platform_device_alloc("wm97xx-battery", -1);
+	if (!wm->battery_dev) {
+		ret = -ENOMEM;
+		goto batt_err;
+	}
+	platform_set_drvdata(wm->battery_dev, wm);
+	wm->battery_dev->dev.parent = dev;
+	ret = platform_device_register(wm->battery_dev);
+	if (ret < 0)
+		goto batt_reg_err;
+
+	/* register our extended touch device (for machine specific
+	 * extensions) */
+	wm->touch_dev = platform_device_alloc("wm97xx-touch", -1);
+	if (!wm->touch_dev) {
+		ret = -ENOMEM;
+		goto touch_err;
+	}
+	platform_set_drvdata(wm->touch_dev, wm);
+	wm->touch_dev->dev.parent = dev;
+	ret = platform_device_register(wm->touch_dev);
+	if (ret < 0)
+		goto touch_reg_err;
+
+	return ret;
+
+ touch_reg_err:
+	platform_device_put(wm->touch_dev);
+ touch_err:
+	platform_device_unregister(wm->battery_dev);
+	wm->battery_dev = 0;
+ batt_reg_err:
+	platform_device_put(wm->battery_dev);
+ batt_err:
+	input_unregister_device(wm->input_dev);
+	wm->input_dev = 0;
+ dev_alloc_err:
+	input_free_device(wm->input_dev);
+ alloc_err:
+	kfree(wm);
+
+	return ret;
+}
+
+static int wm97xx_remove(struct device *dev)
+{
+	struct wm97xx *wm = dev_get_drvdata(dev);
+
+	platform_device_unregister(wm->battery_dev);
+	platform_device_unregister(wm->touch_dev);
+	input_unregister_device(wm->input_dev);
+
+	kfree(wm);
+	return 0;
+}
+
+#ifdef CONFIG_PM
+int wm97xx_resume(struct device *dev)
+{
+	struct wm97xx *wm = dev_get_drvdata(dev);
+
+	/* restore digitiser and gpios */
+	if (wm->id == WM9713_ID2) {
+		wm97xx_reg_write(wm, AC97_WM9713_DIG1, wm->dig[0]);
+		wm97xx_reg_write(wm, 0x5a, wm->misc);
+		if (wm->ts_use_count) {
+			u16 reg;
+			reg = wm97xx_reg_read(wm, AC97_EXTENDED_MID) & 0x7fff;
+			wm97xx_reg_write(wm, AC97_EXTENDED_MID, reg);
+		}
+	}
+
+	wm97xx_reg_write(wm, AC97_WM9713_DIG2, wm->dig[1]);
+	wm97xx_reg_write(wm, AC97_WM9713_DIG3, wm->dig[2]);
+
+	wm97xx_reg_write(wm, AC97_GPIO_CFG, wm->gpio[0]);
+	wm97xx_reg_write(wm, AC97_GPIO_POLARITY, wm->gpio[1]);
+	wm97xx_reg_write(wm, AC97_GPIO_STICKY, wm->gpio[2]);
+	wm97xx_reg_write(wm, AC97_GPIO_WAKEUP, wm->gpio[3]);
+	wm97xx_reg_write(wm, AC97_GPIO_STATUS, wm->gpio[4]);
+	wm97xx_reg_write(wm, AC97_MISC_AFE, wm->gpio[5]);
+
+	return 0;
+}
+
+#else
+#define wm97xx_resume		NULL
+#endif
+
+/*
+ * Machine specific operations
+ */
+int wm97xx_register_mach_ops(struct wm97xx *wm,
+			     struct wm97xx_mach_ops *mach_ops)
+{
+	mutex_lock(&wm->codec_mutex);
+	if (wm->mach_ops) {
+		mutex_unlock(&wm->codec_mutex);
+		return -EINVAL;
+	}
+	wm->mach_ops = mach_ops;
+	mutex_unlock(&wm->codec_mutex);
+	return 0;
+}
+EXPORT_SYMBOL_GPL(wm97xx_register_mach_ops);
+
+void wm97xx_unregister_mach_ops(struct wm97xx *wm)
+{
+	mutex_lock(&wm->codec_mutex);
+	wm->mach_ops = NULL;
+	mutex_unlock(&wm->codec_mutex);
+}
+EXPORT_SYMBOL_GPL(wm97xx_unregister_mach_ops);
+
+static struct device_driver wm97xx_driver = {
+	.name = 	"ac97",
+	.bus = 		&ac97_bus_type,
+	.owner = 	THIS_MODULE,
+	.probe = 	wm97xx_probe,
+	.remove = 	wm97xx_remove,
+	.resume =	wm97xx_resume,
+};
+
+static int __init wm97xx_init(void)
+{
+	return driver_register(&wm97xx_driver);
+}
+
+static void __exit wm97xx_exit(void)
+{
+	driver_unregister(&wm97xx_driver);
+}
+
+module_init(wm97xx_init);
+module_exit(wm97xx_exit);
+
+/* Module information */
+MODULE_AUTHOR("Liam Girdwood <[email protected]>");
+MODULE_DESCRIPTION("WM97xx Core - Touch Screen / AUX ADC / GPIO Driver");
+MODULE_LICENSE("GPL");
include/linux/wm97xx.h new file +309 -0

309 lines not on this page · raw message

Signature · 1 line
1.5.4
author
#10 lore raw

PATCH 1/1 Add chip driver for WM9705 touchscreen

Cc Dmitry Baryshkov <[email protected]>
Cc Stanley Cai <[email protected]>
Cc Rodolfo Giometti <[email protected]>
Cc Russell King <[email protected]>
Cc Marc Kleine-Budde <[email protected]>
Cc Ian Molton <[email protected]>
Cc Vince Sanders <[email protected]>
Cc Andrew Zabolotny <[email protected]>
---
 drivers/input/touchscreen/wm9705.c |  352 ++++++++++++++++++++++++++++++++++++
 1 files changed, 352 insertions(+), 0 deletions(-)
 create mode 100644 drivers/input/touchscreen/wm9705.c
drivers/input/touchscreen/wm9705.c new file +352 -0
new file mode 100644
index 0000000..f185104
@@ -0,0 +1,352 @@
+/*
+ * wm9705.c  --  Codec driver for Wolfson WM9705 AC97 Codec.
+ *
+ * Copyright 2003, 2004, 2005, 2006, 2007 Wolfson Microelectronics PLC.
+ * Author: Liam Girdwood
+ *         [email protected] or [email protected]
+ * Parts Copyright : Ian Molton <[email protected]>
+ *                   Andrew Zabolotny <[email protected]>
+ *                   Russell King <[email protected]>
+ *
+ *  This program is free software; you can redistribute  it and/or modify it
+ *  under  the terms of  the GNU General  Public License as published by the
+ *  Free Software Foundation;  either version 2 of the  License, or (at your
+ *  option) any later version.
+ *
+ */
+
+#include <linux/module.h>
+#include <linux/moduleparam.h>
+#include <linux/version.h>
+#include <linux/kernel.h>
+#include <linux/input.h>
+#include <linux/delay.h>
+#include <linux/bitops.h>
+#include <linux/wm97xx.h>
+
+#define TS_NAME			"wm97xx"
+#define WM9705_VERSION		"0.62"
+#define DEFAULT_PRESSURE	0xb0c0
+
+/*
+ * Module parameters
+ */
+
+/*
+ * Set current used for pressure measurement.
+ *
+ * Set pil = 2 to use 400uA
+ *     pil = 1 to use 200uA and
+ *     pil = 0 to disable pressure measurement.
+ *
+ * This is used to increase the range of values returned by the adc
+ * when measureing touchpanel pressure.
+ */
+static int pil;
+module_param(pil, int, 0);
+MODULE_PARM_DESC(pil, "Set current used for pressure measurement.");
+
+/*
+ * Set threshold for pressure measurement.
+ *
+ * Pen down pressure below threshold is ignored.
+ */
+static int pressure = DEFAULT_PRESSURE & 0xfff;
+module_param(pressure, int, 0);
+MODULE_PARM_DESC(pressure, "Set threshold for pressure measurement.");
+
+/*
+ * Set adc sample delay.
+ *
+ * For accurate touchpanel measurements, some settling time may be
+ * required between the switch matrix applying a voltage across the
+ * touchpanel plate and the ADC sampling the signal.
+ *
+ * This delay can be set by setting delay = n, where n is the array
+ * position of the delay in the array delay_table below.
+ * Long delays > 1ms are supported for completeness, but are not
+ * recommended.
+ */
+static int delay = 4;
+module_param(delay, int, 0);
+MODULE_PARM_DESC(delay, "Set adc sample delay.");
+
+/*
+ * Pen detect comparator threshold.
+ *
+ * 0 to Vmid in 15 steps, 0 = use zero power comparator with Vmid threshold
+ * i.e. 1 =  Vmid/15 threshold
+ *      15 =  Vmid/1 threshold
+ *
+ * Adjust this value if you are having problems with pen detect not
+ * detecting any down events.
+ */
+static int pdd = 8;
+module_param(pdd, int, 0);
+MODULE_PARM_DESC(pdd, "Set pen detect comparator threshold");
+
+/*
+ * Set adc mask function.
+ *
+ * Sources of glitch noise, such as signals driving an LCD display, may feed
+ * through to the touch screen plates and affect measurement accuracy. In
+ * order to minimise this, a signal may be applied to the MASK pin to delay or
+ * synchronise the sampling.
+ *
+ * 0 = No delay or sync
+ * 1 = High on pin stops conversions
+ * 2 = Edge triggered, edge on pin delays conversion by delay param (above)
+ * 3 = Edge triggered, edge on pin starts conversion after delay param
+ */
+static int mask;
+module_param(mask, int, 0);
+MODULE_PARM_DESC(mask, "Set adc mask function.");
+
+/*
+ * ADC sample delay times in uS
+ */
+static const int delay_table[] = {
+	21,    /* 1 AC97 Link frames */
+	42,    /* 2                  */
+	84,    /* 4                  */
+	167,   /* 8                  */
+	333,   /* 16                 */
+	667,   /* 32                 */
+	1000,  /* 48                 */
+	1333,  /* 64                 */
+	2000,  /* 96                 */
+	2667,  /* 128                */
+	3333,  /* 160                */
+	4000,  /* 192                */
+	4667,  /* 224                */
+	5333,  /* 256                */
+	6000,  /* 288                */
+	0      /* No delay, switch matrix always on */
+};
+
+/*
+ * Delay after issuing a POLL command.
+ *
+ * The delay is 3 AC97 link frames + the touchpanel settling delay
+ */
+static inline void poll_delay(int d)
+{
+	udelay(3 * AC97_LINK_FRAME + delay_table[d]);
+}
+
+/*
+ * set up the physical settings of the WM9705
+ */
+static void wm9705_phy_init(struct wm97xx *wm)
+{
+	u16 dig1 = 0, dig2 = WM97XX_RPR;
+
+	/*
+	* mute VIDEO and AUX as they share X and Y touchscreen
+	* inputs on the WM9705
+	*/
+	wm97xx_reg_write(wm, AC97_AUX, 0x8000);
+	wm97xx_reg_write(wm, AC97_VIDEO, 0x8000);
+
+	/* touchpanel pressure current*/
+	if (pil == 2) {
+		dig2 |= WM9705_PIL;
+		dev_dbg(wm->dev,
+			"setting pressure measurement current to 400uA.");
+	} else if (pil)
+		dev_dbg(wm->dev,
+			"setting pressure measurement current to 200uA.");
+	if (!pil)
+		pressure = 0;
+
+	/* polling mode sample settling delay */
+	if (delay != 4) {
+		if (delay < 0 || delay > 15) {
+			dev_dbg(wm->dev, "supplied delay out of range.");
+			delay = 4;
+		}
+	}
+	dig1 &= 0xff0f;
+	dig1 |= WM97XX_DELAY(delay);
+	dev_dbg(wm->dev, "setting adc sample delay to %d u Secs.",
+		delay_table[delay]);
+
+	/* WM9705 pdd */
+	dig2 |= (pdd & 0x000f);
+	dev_dbg(wm->dev, "setting pdd to Vmid/%d", 1 - (pdd & 0x000f));
+
+	/* mask */
+	dig2 |= ((mask & 0x3) << 4);
+
+	wm97xx_reg_write(wm, AC97_WM97XX_DIGITISER1, dig1);
+	wm97xx_reg_write(wm, AC97_WM97XX_DIGITISER2, dig2);
+}
+
+static void wm9705_dig_enable(struct wm97xx *wm, int enable)
+{
+	if (enable) {
+		wm97xx_reg_write(wm, AC97_WM97XX_DIGITISER2,
+				 wm->dig[2] | WM97XX_PRP_DET_DIG);
+		wm97xx_reg_read(wm, AC97_WM97XX_DIGITISER_RD); /* dummy read */
+	} else
+		wm97xx_reg_write(wm, AC97_WM97XX_DIGITISER2,
+				 wm->dig[2] & ~WM97XX_PRP_DET_DIG);
+}
+
+static void wm9705_aux_prepare(struct wm97xx *wm)
+{
+	memcpy(wm->dig_save, wm->dig, sizeof(wm->dig));
+	wm97xx_reg_write(wm, AC97_WM97XX_DIGITISER1, 0);
+	wm97xx_reg_write(wm, AC97_WM97XX_DIGITISER2, WM97XX_PRP_DET_DIG);
+}
+
+static void wm9705_dig_restore(struct wm97xx *wm)
+{
+	wm97xx_reg_write(wm, AC97_WM97XX_DIGITISER1, wm->dig_save[1]);
+	wm97xx_reg_write(wm, AC97_WM97XX_DIGITISER2, wm->dig_save[2]);
+}
+
+static inline int is_pden(struct wm97xx *wm)
+{
+	return wm->dig[2] & WM9705_PDEN;
+}
+
+/*
+ * Read a sample from the WM9705 adc in polling mode.
+ */
+static int wm9705_poll_sample(struct wm97xx *wm, int adcsel, int *sample)
+{
+	int timeout = 5 * delay;
+
+	if (!wm->pen_probably_down) {
+		u16 data = wm97xx_reg_read(wm, AC97_WM97XX_DIGITISER_RD);
+		if (!(data & WM97XX_PEN_DOWN))
+			return RC_PENUP;
+		wm->pen_probably_down = 1;
+	}
+
+	/* set up digitiser */
+	if (adcsel & 0x8000)
+		adcsel = ((adcsel & 0x7fff) + 3) << 12;
+
+	if (wm->mach_ops && wm->mach_ops->pre_sample)
+		wm->mach_ops->pre_sample(adcsel);
+	wm97xx_reg_write(wm, AC97_WM97XX_DIGITISER1,
+			 adcsel | WM97XX_POLL | WM97XX_DELAY(delay));
+
+	/* wait 3 AC97 time slots + delay for conversion */
+	poll_delay(delay);
+
+	/* wait for POLL to go low */
+	while ((wm97xx_reg_read(wm, AC97_WM97XX_DIGITISER1) & WM97XX_POLL)
+	       && timeout) {
+		udelay(AC97_LINK_FRAME);
+		timeout--;
+	}
+
+	if (timeout <= 0) {
+		/* If PDEN is set, we can get a timeout when pen goes up */
+		if (is_pden(wm))
+			wm->pen_probably_down = 0;
+		else
+			dev_dbg(wm->dev, "adc sample timeout");
+		return RC_PENUP;
+	}
+
+	*sample = wm97xx_reg_read(wm, AC97_WM97XX_DIGITISER_RD);
+	if (wm->mach_ops && wm->mach_ops->post_sample)
+		wm->mach_ops->post_sample(adcsel);
+
+	/* check we have correct sample */
+	if ((*sample & WM97XX_ADCSEL_MASK) != adcsel) {
+		dev_dbg(wm->dev, "adc wrong sample, read %x got %x", adcsel,
+		*sample & WM97XX_ADCSEL_MASK);
+		return RC_PENUP;
+	}
+
+	if (!(*sample & WM97XX_PEN_DOWN)) {
+		wm->pen_probably_down = 0;
+		return RC_PENUP;
+	}
+
+	return RC_VALID;
+}
+
+/*
+ * Sample the WM9705 touchscreen in polling mode
+ */
+static int wm9705_poll_touch(struct wm97xx *wm, struct wm97xx_data *data)
+{
+	int rc;
+
+	rc = wm9705_poll_sample(wm, WM97XX_ADCSEL_X, &data->x);
+	if (rc != RC_VALID)
+		return rc;
+	rc = wm9705_poll_sample(wm, WM97XX_ADCSEL_Y, &data->y);
+	if (rc != RC_VALID)
+		return rc;
+	if (pil) {
+		rc = wm9705_poll_sample(wm, WM97XX_ADCSEL_PRES, &data->p);
+		if (rc != RC_VALID)
+			return rc;
+	} else
+		data->p = DEFAULT_PRESSURE;
+
+	return RC_VALID;
+}
+
+/*
+ * Enable WM9705 continuous mode, i.e. touch data is streamed across
+ * an AC97 slot
+ */
+static int wm9705_acc_enable(struct wm97xx *wm, int enable)
+{
+	u16 dig1, dig2;
+	int ret = 0;
+
+	dig1 = wm->dig[1];
+	dig2 = wm->dig[2];
+
+	if (enable) {
+		/* continous mode */
+		if (wm->mach_ops->acc_startup &&
+		    (ret = wm->mach_ops->acc_startup(wm)) < 0)
+			return ret;
+		dig1 &= ~(WM97XX_CM_RATE_MASK | WM97XX_ADCSEL_MASK |
+			  WM97XX_DELAY_MASK | WM97XX_SLT_MASK);
+		dig1 |= WM97XX_CTC | WM97XX_COO | WM97XX_SLEN |
+			WM97XX_DELAY(delay) |
+			WM97XX_SLT(wm->acc_slot) |
+			WM97XX_RATE(wm->acc_rate);
+		if (pil)
+			dig1 |= WM97XX_ADCSEL_PRES;
+		dig2 |= WM9705_PDEN;
+	} else {
+		dig1 &= ~(WM97XX_CTC | WM97XX_COO | WM97XX_SLEN);
+		dig2 &= ~WM9705_PDEN;
+		if (wm->mach_ops->acc_shutdown)
+			wm->mach_ops->acc_shutdown(wm);
+	}
+
+	wm97xx_reg_write(wm, AC97_WM97XX_DIGITISER1, dig1);
+	wm97xx_reg_write(wm, AC97_WM97XX_DIGITISER2, dig2);
+	return ret;
+}
+
+struct wm97xx_codec_drv wm9705_codec = {
+	.id = 	WM9705_ID2,
+	.name = "wm9705",
+	.poll_sample = wm9705_poll_sample,
+	.poll_touch = wm9705_poll_touch,
+	.acc_enable = wm9705_acc_enable,
+	.phy_init = wm9705_phy_init,
+	.dig_enable = wm9705_dig_enable,
+	.dig_restore = wm9705_dig_restore,
+	.aux_prepare = wm9705_aux_prepare,
+};
+EXPORT_SYMBOL_GPL(wm9705_codec);
+
+/* Module information */
+MODULE_AUTHOR("Liam Girdwood <[email protected]>");
+MODULE_DESCRIPTION("WM9705 Touch Screen Driver");
+MODULE_LICENSE("GPL");
Signature · 1 line
1.5.4
author
#11 lore raw

PATCH 1/1 Add chip driver for WM9712 touchscreen

Cc Dmitry Baryshkov <[email protected]>
Cc Stanley Cai <[email protected]>
Cc Rodolfo Giometti <[email protected]>
Cc Russell King <[email protected]>
Cc Marc Kleine-Budde <[email protected]>
Cc Ian Molton <[email protected]>
Cc Vince Sanders <[email protected]>
Cc Andrew Zabolotny <[email protected]>
---
 drivers/input/touchscreen/wm9712.c |  461 ++++++++++++++++++++++++++++++++++++
 1 files changed, 461 insertions(+), 0 deletions(-)
 create mode 100644 drivers/input/touchscreen/wm9712.c
drivers/input/touchscreen/wm9712.c new file +461 -0
new file mode 100644
index 0000000..eaab326
@@ -0,0 +1,461 @@
+/*
+ * wm9712.c  --  Codec driver for Wolfson WM9712 AC97 Codecs.
+ *
+ * Copyright 2003, 2004, 2005, 2006, 2007 Wolfson Microelectronics PLC.
+ * Author: Liam Girdwood
+ *         [email protected] or [email protected]
+ * Parts Copyright : Ian Molton <[email protected]>
+ *                   Andrew Zabolotny <[email protected]>
+ *                   Russell King <[email protected]>
+ *
+ *  This program is free software; you can redistribute  it and/or modify it
+ *  under  the terms of  the GNU General  Public License as published by the
+ *  Free Software Foundation;  either version 2 of the  License, or (at your
+ *  option) any later version.
+ *
+ */
+
+#include <linux/module.h>
+#include <linux/moduleparam.h>
+#include <linux/version.h>
+#include <linux/kernel.h>
+#include <linux/input.h>
+#include <linux/delay.h>
+#include <linux/bitops.h>
+#include <linux/wm97xx.h>
+
+#define TS_NAME			"wm97xx"
+#define WM9712_VERSION		"0.61"
+#define DEFAULT_PRESSURE	0xb0c0
+
+/*
+ * Module parameters
+ */
+
+/*
+ * Set internal pull up for pen detect.
+ *
+ * Pull up is in the range 1.02k (least sensitive) to 64k (most sensitive)
+ * i.e. pull up resistance = 64k Ohms / rpu.
+ *
+ * Adjust this value if you are having problems with pen detect not
+ * detecting any down event.
+ */
+static int rpu = 8;
+module_param(rpu, int, 0);
+MODULE_PARM_DESC(rpu, "Set internal pull up resitor for pen detect.");
+
+/*
+ * Set current used for pressure measurement.
+ *
+ * Set pil = 2 to use 400uA
+ *     pil = 1 to use 200uA and
+ *     pil = 0 to disable pressure measurement.
+ *
+ * This is used to increase the range of values returned by the adc
+ * when measureing touchpanel pressure.
+ */
+static int pil;
+module_param(pil, int, 0);
+MODULE_PARM_DESC(pil, "Set current used for pressure measurement.");
+
+/*
+ * Set threshold for pressure measurement.
+ *
+ * Pen down pressure below threshold is ignored.
+ */
+static int pressure = DEFAULT_PRESSURE & 0xfff;
+module_param(pressure, int, 0);
+MODULE_PARM_DESC(pressure, "Set threshold for pressure measurement.");
+
+/*
+ * Set adc sample delay.
+ *
+ * For accurate touchpanel measurements, some settling time may be
+ * required between the switch matrix applying a voltage across the
+ * touchpanel plate and the ADC sampling the signal.
+ *
+ * This delay can be set by setting delay = n, where n is the array
+ * position of the delay in the array delay_table below.
+ * Long delays > 1ms are supported for completeness, but are not
+ * recommended.
+ */
+static int delay = 3;
+module_param(delay, int, 0);
+MODULE_PARM_DESC(delay, "Set adc sample delay.");
+
+/*
+ * Set five_wire = 1 to use a 5 wire touchscreen.
+ *
+ * NOTE: Five wire mode does not allow for readback of pressure.
+ */
+static int five_wire;
+module_param(five_wire, int, 0);
+MODULE_PARM_DESC(five_wire, "Set to '1' to use 5-wire touchscreen.");
+
+/*
+ * Set adc mask function.
+ *
+ * Sources of glitch noise, such as signals driving an LCD display, may feed
+ * through to the touch screen plates and affect measurement accuracy. In
+ * order to minimise this, a signal may be applied to the MASK pin to delay or
+ * synchronise the sampling.
+ *
+ * 0 = No delay or sync
+ * 1 = High on pin stops conversions
+ * 2 = Edge triggered, edge on pin delays conversion by delay param (above)
+ * 3 = Edge triggered, edge on pin starts conversion after delay param
+ */
+static int mask;
+module_param(mask, int, 0);
+MODULE_PARM_DESC(mask, "Set adc mask function.");
+
+/*
+ * Coordinate Polling Enable.
+ *
+ * Set to 1 to enable coordinate polling. e.g. x,y[,p] is sampled together
+ * for every poll.
+ */
+static int coord;
+module_param(coord, int, 0);
+MODULE_PARM_DESC(coord, "Polling coordinate mode");
+
+/*
+ * ADC sample delay times in uS
+ */
+static const int delay_table[] = {
+	21,    /* 1 AC97 Link frames */
+	42,    /* 2 */
+	84,    /* 4 */
+	167,   /* 8 */
+	333,   /* 16 */
+	667,   /* 32 */
+	1000,  /* 48 */
+	1333,  /* 64 */
+	2000,  /* 96 */
+	2667,  /* 128 */
+	3333,  /* 160 */
+	4000,  /* 192 */
+	4667,  /* 224 */
+	5333,  /* 256 */
+	6000,  /* 288 */
+	0      /* No delay, switch matrix always on */
+};
+
+/*
+ * Delay after issuing a POLL command.
+ *
+ * The delay is 3 AC97 link frames + the touchpanel settling delay
+ */
+static inline void poll_delay(int d)
+{
+	udelay(3 * AC97_LINK_FRAME + delay_table[d]);
+}
+
+/*
+ * set up the physical settings of the WM9712
+ */
+static void wm9712_phy_init(struct wm97xx *wm)
+{
+	u16 dig1 = 0;
+	u16 dig2 = WM97XX_RPR | WM9712_RPU(1);
+
+	/* WM9712 rpu */
+	if (rpu) {
+		dig2 &= 0xffc0;
+		dig2 |= WM9712_RPU(rpu);
+		dev_dbg(wm->dev, "setting pen detect pull-up to %d Ohms",
+			64000 / rpu);
+	}
+
+	/* touchpanel pressure current*/
+	if (pil == 2) {
+		dig2 |= WM9712_PIL;
+		dev_dbg(wm->dev,
+			"setting pressure measurement current to 400uA.");
+	} else if (pil)
+		dev_dbg(wm->dev,
+			"setting pressure measurement current to 200uA.");
+	if (!pil)
+		pressure = 0;
+
+	/* WM9712 five wire */
+	if (five_wire) {
+		dig2 |= WM9712_45W;
+		dev_dbg(wm->dev, "setting 5-wire touchscreen mode.");
+	}
+
+	/* polling mode sample settling delay */
+	if (delay < 0 || delay > 15) {
+		dev_dbg(wm->dev, "supplied delay out of range.");
+		delay = 4;
+	}
+	dig1 &= 0xff0f;
+	dig1 |= WM97XX_DELAY(delay);
+	dev_dbg(wm->dev, "setting adc sample delay to %d u Secs.",
+		delay_table[delay]);
+
+	/* mask */
+	dig2 |= ((mask & 0x3) << 6);
+	if (mask) {
+		u16 reg;
+		/* Set GPIO4 as Mask Pin*/
+		reg = wm97xx_reg_read(wm, AC97_MISC_AFE);
+		wm97xx_reg_write(wm, AC97_MISC_AFE, reg | WM97XX_GPIO_4);
+		reg = wm97xx_reg_read(wm, AC97_GPIO_CFG);
+		wm97xx_reg_write(wm, AC97_GPIO_CFG, reg | WM97XX_GPIO_4);
+	}
+
+	/* wait - coord mode */
+	if (coord)
+		dig2 |= WM9712_WAIT;
+
+	wm97xx_reg_write(wm, AC97_WM97XX_DIGITISER1, dig1);
+	wm97xx_reg_write(wm, AC97_WM97XX_DIGITISER2, dig2);
+}
+
+static void wm9712_dig_enable(struct wm97xx *wm, int enable)
+{
+	u16 dig2 = wm->dig[2];
+
+	if (enable) {
+		wm97xx_reg_write(wm, AC97_WM97XX_DIGITISER2,
+				 dig2 | WM97XX_PRP_DET_DIG);
+		wm97xx_reg_read(wm, AC97_WM97XX_DIGITISER_RD); /* dummy read */
+	} else
+		wm97xx_reg_write(wm, AC97_WM97XX_DIGITISER2,
+				 dig2 & ~WM97XX_PRP_DET_DIG);
+}
+
+static void wm9712_aux_prepare(struct wm97xx *wm)
+{
+	memcpy(wm->dig_save, wm->dig, sizeof(wm->dig));
+	wm97xx_reg_write(wm, AC97_WM97XX_DIGITISER1, 0);
+	wm97xx_reg_write(wm, AC97_WM97XX_DIGITISER2, WM97XX_PRP_DET_DIG);
+}
+
+static void wm9712_dig_restore(struct wm97xx *wm)
+{
+	wm97xx_reg_write(wm, AC97_WM97XX_DIGITISER1, wm->dig_save[1]);
+	wm97xx_reg_write(wm, AC97_WM97XX_DIGITISER2, wm->dig_save[2]);
+}
+
+static inline int is_pden(struct wm97xx *wm)
+{
+	return wm->dig[2] & WM9712_PDEN;
+}
+
+/*
+ * Read a sample from the WM9712 adc in polling mode.
+ */
+static int wm9712_poll_sample(struct wm97xx *wm, int adcsel, int *sample)
+{
+	int timeout = 5 * delay;
+
+	if (!wm->pen_probably_down) {
+		u16 data = wm97xx_reg_read(wm, AC97_WM97XX_DIGITISER_RD);
+		if (!(data & WM97XX_PEN_DOWN))
+			return RC_PENUP;
+		wm->pen_probably_down = 1;
+	}
+
+	/* set up digitiser */
+	if (adcsel & 0x8000)
+		adcsel = ((adcsel & 0x7fff) + 3) << 12;
+
+	if (wm->mach_ops && wm->mach_ops->pre_sample)
+		wm->mach_ops->pre_sample(adcsel);
+	wm97xx_reg_write(wm, AC97_WM97XX_DIGITISER1,
+			 adcsel | WM97XX_POLL | WM97XX_DELAY(delay));
+
+	/* wait 3 AC97 time slots + delay for conversion */
+	poll_delay(delay);
+
+	/* wait for POLL to go low */
+	while ((wm97xx_reg_read(wm, AC97_WM97XX_DIGITISER1) & WM97XX_POLL)
+	       && timeout) {
+		udelay(AC97_LINK_FRAME);
+		timeout--;
+	}
+
+	if (timeout <= 0) {
+		/* If PDEN is set, we can get a timeout when pen goes up */
+		if (is_pden(wm))
+			wm->pen_probably_down = 0;
+		else
+			dev_dbg(wm->dev, "adc sample timeout");
+		return RC_PENUP;
+	}
+
+	*sample = wm97xx_reg_read(wm, AC97_WM97XX_DIGITISER_RD);
+	if (wm->mach_ops && wm->mach_ops->post_sample)
+		wm->mach_ops->post_sample(adcsel);
+
+	/* check we have correct sample */
+	if ((*sample & WM97XX_ADCSEL_MASK) != adcsel) {
+		dev_dbg(wm->dev, "adc wrong sample, read %x got %x", adcsel,
+		*sample & WM97XX_ADCSEL_MASK);
+		return RC_PENUP;
+	}
+
+	if (!(*sample & WM97XX_PEN_DOWN)) {
+		wm->pen_probably_down = 0;
+		return RC_PENUP;
+	}
+
+	return RC_VALID;
+}
+
+/*
+ * Read a coord from the WM9712 adc in polling mode.
+ */
+static int wm9712_poll_coord(struct wm97xx *wm, struct wm97xx_data *data)
+{
+	int timeout = 5 * delay;
+
+	if (!wm->pen_probably_down) {
+		u16 data_rd = wm97xx_reg_read(wm, AC97_WM97XX_DIGITISER_RD);
+		if (!(data_rd & WM97XX_PEN_DOWN))
+			return RC_PENUP;
+		wm->pen_probably_down = 1;
+	}
+
+	/* set up digitiser */
+	if (wm->mach_ops && wm->mach_ops->pre_sample)
+		wm->mach_ops->pre_sample(WM97XX_ADCSEL_X | WM97XX_ADCSEL_Y);
+
+	wm97xx_reg_write(wm, AC97_WM97XX_DIGITISER1,
+		WM97XX_COO | WM97XX_POLL | WM97XX_DELAY(delay));
+
+	/* wait 3 AC97 time slots + delay for conversion and read x */
+	poll_delay(delay);
+	data->x = wm97xx_reg_read(wm, AC97_WM97XX_DIGITISER_RD);
+	/* wait for POLL to go low */
+	while ((wm97xx_reg_read(wm, AC97_WM97XX_DIGITISER1) & WM97XX_POLL)
+	       && timeout) {
+		udelay(AC97_LINK_FRAME);
+		timeout--;
+	}
+
+	if (timeout <= 0) {
+		/* If PDEN is set, we can get a timeout when pen goes up */
+		if (is_pden(wm))
+			wm->pen_probably_down = 0;
+		else
+			dev_dbg(wm->dev, "adc sample timeout");
+		return RC_PENUP;
+	}
+
+	/* read back y data */
+	data->y = wm97xx_reg_read(wm, AC97_WM97XX_DIGITISER_RD);
+	if (pil)
+		data->p = wm97xx_reg_read(wm, AC97_WM97XX_DIGITISER_RD);
+	else
+		data->p = DEFAULT_PRESSURE;
+
+	if (wm->mach_ops && wm->mach_ops->post_sample)
+		wm->mach_ops->post_sample(WM97XX_ADCSEL_X | WM97XX_ADCSEL_Y);
+
+	/* check we have correct sample */
+	if (!(data->x & WM97XX_ADCSEL_X) || !(data->y & WM97XX_ADCSEL_Y))
+		goto err;
+	if (pil && !(data->p & WM97XX_ADCSEL_PRES))
+		goto err;
+
+	if (!(data->x & WM97XX_PEN_DOWN)) {
+		wm->pen_probably_down = 0;
+		return RC_PENUP;
+	}
+	return RC_VALID;
+err:
+	return RC_PENUP;
+}
+
+/*
+ * Sample the WM9712 touchscreen in polling mode
+ */
+static int wm9712_poll_touch(struct wm97xx *wm, struct wm97xx_data *data)
+{
+	int rc;
+
+	if (coord) {
+		rc = wm9712_poll_coord(wm, data);
+		if (rc != RC_VALID)
+			return rc;
+	} else {
+		rc = wm9712_poll_sample(wm, WM97XX_ADCSEL_X, &data->x);
+		if (rc != RC_VALID)
+			return rc;
+
+		rc = wm9712_poll_sample(wm, WM97XX_ADCSEL_Y, &data->y);
+		if (rc != RC_VALID)
+			return rc;
+
+		if (pil && !five_wire) {
+			rc = wm9712_poll_sample(wm, WM97XX_ADCSEL_PRES,
+						&data->p);
+			if (rc != RC_VALID)
+				return rc;
+		} else
+			data->p = DEFAULT_PRESSURE;
+	}
+	return RC_VALID;
+}
+
+/*
+ * Enable WM9712 continuous mode, i.e. touch data is streamed across
+ * an AC97 slot
+ */
+static int wm9712_acc_enable(struct wm97xx *wm, int enable)
+{
+	u16 dig1, dig2;
+	int ret = 0;
+
+	dig1 = wm->dig[1];
+	dig2 = wm->dig[2];
+
+	if (enable) {
+		/* continous mode */
+		if (wm->mach_ops->acc_startup) {
+			ret = wm->mach_ops->acc_startup(wm);
+			if (ret < 0)
+				return ret;
+		}
+		dig1 &= ~(WM97XX_CM_RATE_MASK | WM97XX_ADCSEL_MASK |
+			WM97XX_DELAY_MASK | WM97XX_SLT_MASK);
+		dig1 |= WM97XX_CTC | WM97XX_COO | WM97XX_SLEN |
+			WM97XX_DELAY(delay) |
+			WM97XX_SLT(wm->acc_slot) |
+			WM97XX_RATE(wm->acc_rate);
+		if (pil)
+			dig1 |= WM97XX_ADCSEL_PRES;
+		dig2 |= WM9712_PDEN;
+	} else {
+		dig1 &= ~(WM97XX_CTC | WM97XX_COO | WM97XX_SLEN);
+		dig2 &= ~WM9712_PDEN;
+		if (wm->mach_ops->acc_shutdown)
+			wm->mach_ops->acc_shutdown(wm);
+	}
+
+	wm97xx_reg_write(wm, AC97_WM97XX_DIGITISER1, dig1);
+	wm97xx_reg_write(wm, AC97_WM97XX_DIGITISER2, dig2);
+	return 0;
+}
+
+struct wm97xx_codec_drv wm9712_codec = {
+	.id = 	WM9712_ID2,
+	.name = "wm9712",
+	.poll_sample = wm9712_poll_sample,
+	.poll_touch = wm9712_poll_touch,
+	.acc_enable = wm9712_acc_enable,
+	.phy_init = wm9712_phy_init,
+	.dig_enable = wm9712_dig_enable,
+	.dig_restore = wm9712_dig_restore,
+	.aux_prepare = wm9712_aux_prepare,
+};
+EXPORT_SYMBOL_GPL(wm9712_codec);
+
+/* Module information */
+MODULE_AUTHOR("Liam Girdwood <[email protected]>");
+MODULE_DESCRIPTION("WM9712 Touch Screen Driver");
+MODULE_LICENSE("GPL");
Signature · 1 line
1.5.4
author
#12 lore raw

PATCH 1/1 Add chip driver for WM9713 touchscreen

Cc Dmitry Baryshkov <[email protected]>
Cc Stanley Cai <[email protected]>
Cc Rodolfo Giometti <[email protected]>
Cc Russell King <[email protected]>
Cc Marc Kleine-Budde <[email protected]>
Cc Ian Molton <[email protected]>
Cc Vince Sanders <[email protected]>
Cc Andrew Zabolotny <[email protected]>
---
 drivers/input/touchscreen/wm9713.c |  459 ++++++++++++++++++++++++++++++++++++
 1 files changed, 459 insertions(+), 0 deletions(-)
 create mode 100644 drivers/input/touchscreen/wm9713.c
drivers/input/touchscreen/wm9713.c new file +459 -0
new file mode 100644
index 0000000..5067e59
@@ -0,0 +1,459 @@
+/*
+ * wm9713.c  --  Codec touch driver for Wolfson WM9713 AC97 Codec.
+ *
+ * Copyright 2003, 2004, 2005, 2006, 2007, 2008 Wolfson Microelectronics PLC.
+ * Author: Liam Girdwood
+ *         [email protected] or [email protected]
+ * Parts Copyright : Ian Molton <[email protected]>
+ *                   Andrew Zabolotny <[email protected]>
+ *                   Russell King <[email protected]>
+ *
+ *  This program is free software; you can redistribute  it and/or modify it
+ *  under  the terms of  the GNU General  Public License as published by the
+ *  Free Software Foundation;  either version 2 of the  License, or (at your
+ *  option) any later version.
+ *
+ */
+
+#include <linux/module.h>
+#include <linux/moduleparam.h>
+#include <linux/version.h>
+#include <linux/kernel.h>
+#include <linux/input.h>
+#include <linux/delay.h>
+#include <linux/bitops.h>
+#include <linux/wm97xx.h>
+
+#define TS_NAME			"wm97xx"
+#define WM9713_VERSION		"0.53"
+#define DEFAULT_PRESSURE	0xb0c0
+
+/*
+ * Module parameters
+ */
+
+/*
+ * Set internal pull up for pen detect.
+ *
+ * Pull up is in the range 1.02k (least sensitive) to 64k (most sensitive)
+ * i.e. pull up resistance = 64k Ohms / rpu.
+ *
+ * Adjust this value if you are having problems with pen detect not
+ * detecting any down event.
+ */
+static int rpu = 8;
+module_param(rpu, int, 0);
+MODULE_PARM_DESC(rpu, "Set internal pull up resitor for pen detect.");
+
+/*
+ * Set current used for pressure measurement.
+ *
+ * Set pil = 2 to use 400uA
+ *     pil = 1 to use 200uA and
+ *     pil = 0 to disable pressure measurement.
+ *
+ * This is used to increase the range of values returned by the adc
+ * when measureing touchpanel pressure.
+ */
+static int pil;
+module_param(pil, int, 0);
+MODULE_PARM_DESC(pil, "Set current used for pressure measurement.");
+
+/*
+ * Set threshold for pressure measurement.
+ *
+ * Pen down pressure below threshold is ignored.
+ */
+static int pressure = DEFAULT_PRESSURE & 0xfff;
+module_param(pressure, int, 0);
+MODULE_PARM_DESC(pressure, "Set threshold for pressure measurement.");
+
+/*
+ * Set adc sample delay.
+ *
+ * For accurate touchpanel measurements, some settling time may be
+ * required between the switch matrix applying a voltage across the
+ * touchpanel plate and the ADC sampling the signal.
+ *
+ * This delay can be set by setting delay = n, where n is the array
+ * position of the delay in the array delay_table below.
+ * Long delays > 1ms are supported for completeness, but are not
+ * recommended.
+ */
+static int delay = 4;
+module_param(delay, int, 0);
+MODULE_PARM_DESC(delay, "Set adc sample delay.");
+
+/*
+ * Set adc mask function.
+ *
+ * Sources of glitch noise, such as signals driving an LCD display, may feed
+ * through to the touch screen plates and affect measurement accuracy. In
+ * order to minimise this, a signal may be applied to the MASK pin to delay or
+ * synchronise the sampling.
+ *
+ * 0 = No delay or sync
+ * 1 = High on pin stops conversions
+ * 2 = Edge triggered, edge on pin delays conversion by delay param (above)
+ * 3 = Edge triggered, edge on pin starts conversion after delay param
+ */
+static int mask;
+module_param(mask, int, 0);
+MODULE_PARM_DESC(mask, "Set adc mask function.");
+
+/*
+ * Coordinate Polling Enable.
+ *
+ * Set to 1 to enable coordinate polling. e.g. x,y[,p] is sampled together
+ * for every poll.
+ */
+static int coord;
+module_param(coord, int, 0);
+MODULE_PARM_DESC(coord, "Polling coordinate mode");
+
+/*
+ * ADC sample delay times in uS
+ */
+static const int delay_table[] = {
+	21,    /* 1 AC97 Link frames */
+	42,    /* 2 */
+	84,    /* 4 */
+	167,   /* 8 */
+	333,   /* 16 */
+	667,   /* 32 */
+	1000,  /* 48 */
+	1333,  /* 64 */
+	2000,  /* 96 */
+	2667,  /* 128 */
+	3333,  /* 160 */
+	4000,  /* 192 */
+	4667,  /* 224 */
+	5333,  /* 256 */
+	6000,  /* 288 */
+	0      /* No delay, switch matrix always on */
+};
+
+/*
+ * Delay after issuing a POLL command.
+ *
+ * The delay is 3 AC97 link frames + the touchpanel settling delay
+ */
+static inline void poll_delay(int d)
+{
+	udelay(3 * AC97_LINK_FRAME + delay_table[d]);
+}
+
+/*
+ * set up the physical settings of the WM9713
+ */
+static void wm9713_phy_init(struct wm97xx *wm)
+{
+	u16 dig1 = 0, dig2, dig3;
+
+	/* default values */
+	dig2 = WM97XX_DELAY(4) | WM97XX_SLT(5);
+	dig3 = WM9712_RPU(1);
+
+	/* rpu */
+	if (rpu) {
+		dig3 &= 0xffc0;
+		dig3 |= WM9712_RPU(rpu);
+		dev_info(wm->dev, "setting pen detect pull-up to %d Ohms\n",
+			 64000 / rpu);
+	}
+
+	/* touchpanel pressure */
+	if (pil == 2) {
+		dig3 |= WM9712_PIL;
+		dev_info(wm->dev,
+			 "setting pressure measurement current to 400uA.");
+	} else if (pil)
+		dev_info(wm->dev,
+			 "setting pressure measurement current to 200uA.");
+	if (!pil)
+		pressure = 0;
+
+	/* sample settling delay */
+	if (delay < 0 || delay > 15) {
+		dev_info(wm->dev, "supplied delay out of range.");
+		delay = 4;
+		dev_info(wm->dev, "setting adc sample delay to %d u Secs.",
+			 delay_table[delay]);
+	}
+	dig2 &= 0xff0f;
+	dig2 |= WM97XX_DELAY(delay);
+
+	/* mask */
+	dig3 |= ((mask & 0x3) << 4);
+	if (coord)
+		dig3 |= WM9713_WAIT;
+
+	wm->misc = wm97xx_reg_read(wm, 0x5a);
+
+	wm97xx_reg_write(wm, AC97_WM9713_DIG1, dig1);
+	wm97xx_reg_write(wm, AC97_WM9713_DIG2, dig2);
+	wm97xx_reg_write(wm, AC97_WM9713_DIG3, dig3);
+	wm97xx_reg_write(wm, AC97_GPIO_STICKY, 0x0);
+}
+
+static void wm9713_dig_enable(struct wm97xx *wm, int enable)
+{
+	u16 val;
+
+	if (enable) {
+		val = wm97xx_reg_read(wm, AC97_EXTENDED_MID);
+		wm97xx_reg_write(wm, AC97_EXTENDED_MID, val & 0x7fff);
+		wm97xx_reg_write(wm, AC97_WM9713_DIG3, wm->dig[2] |
+				 WM97XX_PRP_DET_DIG);
+		wm97xx_reg_read(wm, AC97_WM97XX_DIGITISER_RD); /* dummy read */
+	} else {
+		wm97xx_reg_write(wm, AC97_WM9713_DIG3, wm->dig[2] &
+					~WM97XX_PRP_DET_DIG);
+		val = wm97xx_reg_read(wm, AC97_EXTENDED_MID);
+		wm97xx_reg_write(wm, AC97_EXTENDED_MID, val | 0x8000);
+	}
+}
+
+static void wm9713_dig_restore(struct wm97xx *wm)
+{
+	wm97xx_reg_write(wm, AC97_WM9713_DIG1, wm->dig_save[0]);
+	wm97xx_reg_write(wm, AC97_WM9713_DIG2, wm->dig_save[1]);
+	wm97xx_reg_write(wm, AC97_WM9713_DIG3, wm->dig_save[2]);
+}
+
+static void wm9713_aux_prepare(struct wm97xx *wm)
+{
+	memcpy(wm->dig_save, wm->dig, sizeof(wm->dig));
+	wm97xx_reg_write(wm, AC97_WM9713_DIG1, 0);
+	wm97xx_reg_write(wm, AC97_WM9713_DIG2, 0);
+	wm97xx_reg_write(wm, AC97_WM9713_DIG3, WM97XX_PRP_DET_DIG);
+}
+
+static inline int is_pden(struct wm97xx *wm)
+{
+	return wm->dig[2] & WM9713_PDEN;
+}
+
+/*
+ * Read a sample from the WM9713 adc in polling mode.
+ */
+static int wm9713_poll_sample(struct wm97xx *wm, int adcsel, int *sample)
+{
+	u16 dig1;
+	int timeout = 5 * delay;
+
+	if (!wm->pen_probably_down) {
+		u16 data = wm97xx_reg_read(wm, AC97_WM97XX_DIGITISER_RD);
+		if (!(data & WM97XX_PEN_DOWN))
+			return RC_PENUP;
+		wm->pen_probably_down = 1;
+	}
+
+	/* set up digitiser */
+	if (adcsel & 0x8000)
+		adcsel = 1 << ((adcsel & 0x7fff) + 3);
+
+	dig1 = wm97xx_reg_read(wm, AC97_WM9713_DIG1);
+	dig1 &= ~WM9713_ADCSEL_MASK;
+
+	if (wm->mach_ops && wm->mach_ops->pre_sample)
+		wm->mach_ops->pre_sample(adcsel);
+	wm97xx_reg_write(wm, AC97_WM9713_DIG1, dig1 | adcsel | WM9713_POLL);
+
+	/* wait 3 AC97 time slots + delay for conversion */
+	poll_delay(delay);
+
+	/* wait for POLL to go low */
+	while ((wm97xx_reg_read(wm, AC97_WM9713_DIG1) & WM9713_POLL) &&
+		timeout) {
+		udelay(AC97_LINK_FRAME);
+		timeout--;
+	}
+
+	if (timeout <= 0) {
+		/* If PDEN is set, we can get a timeout when pen goes up */
+		if (is_pden(wm))
+			wm->pen_probably_down = 0;
+		else
+			dev_dbg(wm->dev, "adc sample timeout");
+		return RC_PENUP;
+	}
+
+	*sample = wm97xx_reg_read(wm, AC97_WM97XX_DIGITISER_RD);
+	if (wm->mach_ops && wm->mach_ops->post_sample)
+		wm->mach_ops->post_sample(adcsel);
+
+	/* check we have correct sample */
+	if ((*sample & WM97XX_ADCSRC_MASK) != ffs(adcsel >> 1) << 12) {
+		dev_dbg(wm->dev, "adc wrong sample, read %x got %x", adcsel,
+			*sample & WM97XX_ADCSRC_MASK);
+		return RC_PENUP;
+	}
+
+	if (!(*sample & WM97XX_PEN_DOWN)) {
+		wm->pen_probably_down = 0;
+		return RC_PENUP;
+	}
+
+	return RC_VALID;
+}
+
+/*
+ * Read a coordinate from the WM9713 adc in polling mode.
+ */
+static int wm9713_poll_coord(struct wm97xx *wm, struct wm97xx_data *data)
+{
+	u16 dig1;
+	int timeout = 5 * delay;
+
+	if (!wm->pen_probably_down) {
+		u16 data = wm97xx_reg_read(wm, AC97_WM97XX_DIGITISER_RD);
+		if (!(data & WM97XX_PEN_DOWN))
+			return RC_PENUP;
+		wm->pen_probably_down = 1;
+	}
+
+	/* set up digitiser */
+	dig1 = wm97xx_reg_read(wm, AC97_WM9713_DIG1);
+	dig1 &= ~WM9713_ADCSEL_MASK;
+	if (pil)
+		dig1 |= WM97XX_ADCSEL_PRES;
+
+	if (wm->mach_ops && wm->mach_ops->pre_sample)
+		wm->mach_ops->pre_sample(WM97XX_ADCSEL_X | WM97XX_ADCSEL_Y);
+	wm97xx_reg_write(wm, AC97_WM9713_DIG1,
+			 dig1 | WM9713_POLL | WM9713_COO);
+
+	/* wait 3 AC97 time slots + delay for conversion */
+	poll_delay(delay);
+	data->x = wm97xx_reg_read(wm, AC97_WM97XX_DIGITISER_RD);
+	/* wait for POLL to go low */
+	while ((wm97xx_reg_read(wm, AC97_WM9713_DIG1) & WM9713_POLL)
+	       && timeout) {
+		udelay(AC97_LINK_FRAME);
+		timeout--;
+	}
+
+	if (timeout <= 0) {
+		/* If PDEN is set, we can get a timeout when pen goes up */
+		if (is_pden(wm))
+			wm->pen_probably_down = 0;
+		else
+			dev_dbg(wm->dev, "adc sample timeout");
+		return RC_PENUP;
+	}
+
+	/* read back data */
+	data->y = wm97xx_reg_read(wm, AC97_WM97XX_DIGITISER_RD);
+	if (pil)
+		data->p = wm97xx_reg_read(wm, AC97_WM97XX_DIGITISER_RD);
+	else
+		data->p = DEFAULT_PRESSURE;
+
+	if (wm->mach_ops && wm->mach_ops->post_sample)
+		wm->mach_ops->post_sample(WM97XX_ADCSEL_X | WM97XX_ADCSEL_Y);
+
+	/* check we have correct sample */
+	if (!(data->x & WM97XX_ADCSEL_X) || !(data->y & WM97XX_ADCSEL_Y))
+		goto err;
+	if (pil && !(data->p & WM97XX_ADCSEL_PRES))
+		goto err;
+
+	if (!(data->x & WM97XX_PEN_DOWN)) {
+		wm->pen_probably_down = 0;
+		return RC_PENUP;
+	}
+	return RC_VALID;
+err:
+	return RC_PENUP;
+}
+
+/*
+ * Sample the WM9713 touchscreen in polling mode
+ */
+static int wm9713_poll_touch(struct wm97xx *wm, struct wm97xx_data *data)
+{
+	int rc;
+
+	if (coord) {
+		rc = wm9713_poll_coord(wm, data);
+		if (rc != RC_VALID)
+			return rc;
+	} else {
+		rc = wm9713_poll_sample(wm, WM9713_ADCSEL_X, &data->x);
+		if (rc != RC_VALID)
+			return rc;
+		rc = wm9713_poll_sample(wm, WM9713_ADCSEL_Y, &data->y);
+		if (rc != RC_VALID)
+			return rc;
+		if (pil) {
+			rc = wm9713_poll_sample(wm, WM9713_ADCSEL_PRES,
+						&data->p);
+			if (rc != RC_VALID)
+				return rc;
+		} else
+			data->p = DEFAULT_PRESSURE;
+	}
+	return RC_VALID;
+}
+
+/*
+ * Enable WM9713 continuous mode, i.e. touch data is streamed across
+ * an AC97 slot
+ */
+static int wm9713_acc_enable(struct wm97xx *wm, int enable)
+{
+	u16 dig1, dig2, dig3;
+	int ret = 0;
+
+	dig1 = wm->dig[0];
+	dig2 = wm->dig[1];
+	dig3 = wm->dig[2];
+
+	if (enable) {
+		/* continous mode */
+		if (wm->mach_ops->acc_startup &&
+			(ret = wm->mach_ops->acc_startup(wm)) < 0)
+			return ret;
+
+		dig1 &= ~WM9713_ADCSEL_MASK;
+		dig1 |= WM9713_CTC | WM9713_COO | WM9713_ADCSEL_X |
+			WM9713_ADCSEL_Y;
+		if (pil)
+			dig1 |= WM9713_ADCSEL_PRES;
+		dig2 &= ~(WM97XX_DELAY_MASK | WM97XX_SLT_MASK  |
+			WM97XX_CM_RATE_MASK);
+		dig2 |= WM97XX_SLEN | WM97XX_DELAY(delay) |
+		WM97XX_SLT(wm->acc_slot) | WM97XX_RATE(wm->acc_rate);
+		dig3 |= WM9713_PDEN;
+	} else {
+		dig1 &= ~(WM9713_CTC | WM9713_COO);
+		dig2 &= ~WM97XX_SLEN;
+		dig3 &= ~WM9713_PDEN;
+		if (wm->mach_ops->acc_shutdown)
+			wm->mach_ops->acc_shutdown(wm);
+	}
+
+	wm97xx_reg_write(wm, AC97_WM9713_DIG1, dig1);
+	wm97xx_reg_write(wm, AC97_WM9713_DIG2, dig2);
+	wm97xx_reg_write(wm, AC97_WM9713_DIG3, dig3);
+	return ret;
+}
+
+struct wm97xx_codec_drv wm9713_codec = {
+	.id = 	WM9713_ID2,
+	.name = "wm9713",
+	.poll_sample = wm9713_poll_sample,
+	.poll_touch = wm9713_poll_touch,
+	.acc_enable = wm9713_acc_enable,
+	.phy_init = wm9713_phy_init,
+	.dig_enable = wm9713_dig_enable,
+	.dig_restore = wm9713_dig_restore,
+	.aux_prepare = wm9713_aux_prepare,
+};
+EXPORT_SYMBOL_GPL(wm9713_codec);
+
+/* Module information */
+MODULE_AUTHOR("Liam Girdwood <[email protected]>");
+MODULE_DESCRIPTION("WM9713 Touch Screen Driver");
+MODULE_LICENSE("GPL");
Signature · 1 line
1.5.4
author
#13 lore raw

PATCH 1/1 Driver for WM97xx touchscreens in streaming mode on Mainstone

Cc Dmitry Baryshkov <[email protected]>
Cc Stanley Cai <[email protected]>
Cc Rodolfo Giometti <[email protected]>
Cc Russell King <[email protected]>
Cc Marc Kleine-Budde <[email protected]>
Cc Ian Molton <[email protected]>
Cc Vince Sanders <[email protected]>
Cc Andrew Zabolotny <[email protected]>
---
 drivers/input/touchscreen/mainstone-wm97xx.c |  298 ++++++++++++++++++++++++++
 1 files changed, 298 insertions(+), 0 deletions(-)
 create mode 100644 drivers/input/touchscreen/mainstone-wm97xx.c
drivers/input/touchscreen/mainstone-wm97xx.c new file +298 -0
new file mode 100644
index 0000000..8e1c35d
@@ -0,0 +1,298 @@
+/*
+ * mainstone-wm97xx.c  --  Mainstone Continuous Touch screen driver for
+ *                         Wolfson WM97xx AC97 Codecs.
+ *
+ * Copyright 2004, 2007 Wolfson Microelectronics PLC.
+ * Author: Liam Girdwood
+ *         [email protected] or [email protected]
+ * Parts Copyright : Ian Molton <[email protected]>
+ *                   Andrew Zabolotny <[email protected]>
+ *
+ *  This program is free software; you can redistribute  it and/or modify it
+ *  under  the terms of  the GNU General  Public License as published by the
+ *  Free Software Foundation;  either version 2 of the  License, or (at your
+ *  option) any later version.
+ *
+ * Notes:
+ *     This is a wm97xx extended touch driver to capture touch
+ *     data in a continuous manner on the Intel XScale archictecture
+ *
+ *  Features:
+ *       - codecs supported:- WM9705, WM9712, WM9713
+ *       - processors supported:- Intel XScale PXA25x, PXA26x, PXA27x
+ *
+ */
+
+#include <linux/module.h>
+#include <linux/moduleparam.h>
+#include <linux/version.h>
+#include <linux/kernel.h>
+#include <linux/init.h>
+#include <linux/delay.h>
+#include <linux/irq.h>
+#include <linux/interrupt.h>
+#include <linux/wm97xx.h>
+#include <linux/io.h>
+#include <asm/arch/pxa-regs.h>
+
+#define VERSION		"0.13"
+
+struct continuous {
+	u16 id;    /* codec id */
+	u8 code;   /* continuous code */
+	u8 reads;  /* number of coord reads per read cycle */
+	u32 speed; /* number of coords per second */
+};
+
+#define WM_READS(sp) ((sp / HZ) + 1)
+
+static const struct continuous cinfo[] = {
+	{WM9705_ID2, 0, WM_READS(94), 94},
+	{WM9705_ID2, 1, WM_READS(188), 188},
+	{WM9705_ID2, 2, WM_READS(375), 375},
+	{WM9705_ID2, 3, WM_READS(750), 750},
+	{WM9712_ID2, 0, WM_READS(94), 94},
+	{WM9712_ID2, 1, WM_READS(188), 188},
+	{WM9712_ID2, 2, WM_READS(375), 375},
+	{WM9712_ID2, 3, WM_READS(750), 750},
+	{WM9713_ID2, 0, WM_READS(94), 94},
+	{WM9713_ID2, 1, WM_READS(120), 120},
+	{WM9713_ID2, 2, WM_READS(154), 154},
+	{WM9713_ID2, 3, WM_READS(188), 188},
+};
+
+/* continuous speed index */
+static int sp_idx;
+static u16 last, tries;
+
+/*
+ * Pen sampling frequency (Hz) in continuous mode.
+ */
+static int cont_rate = 200;
+module_param(cont_rate, int, 0);
+MODULE_PARM_DESC(cont_rate, "Sampling rate in continuous mode (Hz)");
+
+/*
+ * Pen down detection.
+ *
+ * This driver can either poll or use an interrupt to indicate a pen down
+ * event. If the irq request fails then it will fall back to polling mode.
+ */
+static int pen_int;
+module_param(pen_int, int, 0);
+MODULE_PARM_DESC(pen_int, "Pen down detection (1 = interrupt, 0 = polling)");
+
+/*
+ * Pressure readback.
+ *
+ * Set to 1 to read back pen down pressure
+ */
+static int pressure;
+module_param(pressure, int, 0);
+MODULE_PARM_DESC(pressure, "Pressure readback (1 = pressure, 0 = no pressure)");
+
+/*
+ * AC97 touch data slot.
+ *
+ * Touch screen readback data ac97 slot
+ */
+static int ac97_touch_slot = 5;
+module_param(ac97_touch_slot, int, 0);
+MODULE_PARM_DESC(ac97_touch_slot, "Touch screen data slot AC97 number");
+
+
+/* flush AC97 slot 5 FIFO on pxa machines */
+#ifdef CONFIG_PXA27x
+static void wm97xx_acc_pen_up(struct wm97xx *wm)
+{
+	set_current_state(TASK_INTERRUPTIBLE);
+	schedule_timeout(1);
+
+	while (MISR & (1 << 2))
+		MODR;
+}
+#else
+static void wm97xx_acc_pen_up(struct wm97xx *wm)
+{
+	int count = 16;
+	set_current_state(TASK_INTERRUPTIBLE);
+	schedule_timeout(1);
+
+	while (count < 16) {
+		MODR;
+		count--;
+	}
+}
+#endif
+
+static int wm97xx_acc_pen_down(struct wm97xx *wm)
+{
+	u16 x, y, p = 0x100 | WM97XX_ADCSEL_PRES;
+	int reads = 0;
+
+	/* data is never immediately available after pen down irq */
+	set_current_state(TASK_INTERRUPTIBLE);
+	schedule_timeout(1);
+
+	if (tries > 5) {
+		tries = 0;
+		return RC_PENUP;
+	}
+
+	x = MODR;
+	if (x == last) {
+		tries++;
+		return RC_AGAIN;
+	}
+	last = x;
+	do {
+		if (reads)
+			x = MODR;
+		y = MODR;
+		if (pressure)
+			p = MODR;
+
+		/* are samples valid */
+		if ((x & 0x7000) != WM97XX_ADCSEL_X ||
+			(y & 0x7000) != WM97XX_ADCSEL_Y ||
+			(p & 0x7000) != WM97XX_ADCSEL_PRES)
+			goto up;
+
+		/* coordinate is good */
+		tries = 0;
+		input_report_abs(wm->input_dev, ABS_X, x & 0xfff);
+		input_report_abs(wm->input_dev, ABS_Y, y & 0xfff);
+		input_report_abs(wm->input_dev, ABS_PRESSURE, p & 0xfff);
+		input_sync(wm->input_dev);
+		reads++;
+	} while (reads < cinfo[sp_idx].reads);
+up:
+	return RC_PENDOWN | RC_AGAIN;
+}
+
+static int wm97xx_acc_startup(struct wm97xx *wm)
+{
+	int idx = 0;
+
+	/* check we have a codec */
+	if (wm->ac97 == NULL)
+		return -ENODEV;
+
+	/* Go you big red fire engine */
+	for (idx = 0; idx < ARRAY_SIZE(cinfo); idx++) {
+		if (wm->id != cinfo[idx].id)
+			continue;
+		sp_idx = idx;
+		if (cont_rate <= cinfo[idx].speed)
+			break;
+	}
+	wm->acc_rate = cinfo[sp_idx].code;
+	wm->acc_slot = ac97_touch_slot;
+	dev_info(wm->dev,
+		 "mainstone accelerated touchscreen driver, %d samples/sec\n",
+		 cinfo[sp_idx].speed);
+
+	/* codec specific irq config */
+	if (pen_int) {
+		switch (wm->id) {
+		case WM9705_ID2:
+			wm->pen_irq = IRQ_GPIO(4);
+			set_irq_type(IRQ_GPIO(4), IRQT_BOTHEDGE);
+			break;
+		case WM9712_ID2:
+		case WM9713_ID2:
+			/* enable pen down interrupt */
+			/* use PEN_DOWN GPIO 13 to assert IRQ on GPIO line 2 */
+			wm->pen_irq = MAINSTONE_AC97_IRQ;
+			wm97xx_config_gpio(wm, WM97XX_GPIO_13, WM97XX_GPIO_IN,
+					   WM97XX_GPIO_POL_HIGH,
+					   WM97XX_GPIO_STICKY,
+					   WM97XX_GPIO_WAKE);
+			wm97xx_config_gpio(wm, WM97XX_GPIO_2, WM97XX_GPIO_OUT,
+					   WM97XX_GPIO_POL_HIGH,
+					   WM97XX_GPIO_NOTSTICKY,
+					   WM97XX_GPIO_NOWAKE);
+			break;
+		default:
+			dev_err(wm->dev,
+				"pen down irq not supported on this device\n");
+			pen_int = 0;
+			break;
+		}
+	}
+
+	return 0;
+}
+
+static void wm97xx_acc_shutdown(struct wm97xx *wm)
+{
+	/* codec specific deconfig */
+	if (pen_int) {
+		switch (wm->id & 0xffff) {
+		case WM9705_ID2:
+			wm->pen_irq = 0;
+			break;
+		case WM9712_ID2:
+		case WM9713_ID2:
+			/* disable interrupt */
+			wm->pen_irq = 0;
+			break;
+		}
+	}
+}
+
+static void wm97xx_irq_enable(struct wm97xx *wm, int enable)
+{
+	if (enable)
+		enable_irq(wm->pen_irq);
+	else
+		disable_irq(wm->pen_irq);
+}
+
+static struct wm97xx_mach_ops mainstone_mach_ops = {
+	.acc_enabled = 1,
+	.acc_pen_up = wm97xx_acc_pen_up,
+	.acc_pen_down = wm97xx_acc_pen_down,
+	.acc_startup = wm97xx_acc_startup,
+	.acc_shutdown = wm97xx_acc_shutdown,
+	.irq_enable = wm97xx_irq_enable,
+};
+
+static int mainstone_wm97xx_probe(struct platform_device *pdev)
+{
+	struct wm97xx *wm = platform_get_drvdata(pdev);
+	return wm97xx_register_mach_ops(wm, &mainstone_mach_ops);
+}
+
+static int mainstone_wm97xx_remove(struct platform_device *pdev)
+{
+	struct wm97xx *wm = platform_get_drvdata(pdev);
+	wm97xx_unregister_mach_ops(wm);
+	return 0;
+}
+
+static struct platform_driver mainstone_wm97xx_driver = {
+	.probe = mainstone_wm97xx_probe,
+	.remove = mainstone_wm97xx_remove,
+	.driver = {
+		.name = "wm97xx-touch",
+	},
+};
+
+static int __init mainstone_wm97xx_init(void)
+{
+	return platform_driver_register(&mainstone_wm97xx_driver);
+}
+
+static void __exit mainstone_wm97xx_exit(void)
+{
+	platform_driver_unregister(&mainstone_wm97xx_driver);
+}
+
+module_init(mainstone_wm97xx_init);
+module_exit(mainstone_wm97xx_exit);
+
+/* Module information */
+MODULE_AUTHOR("Liam Girdwood <[email protected]>");
+MODULE_DESCRIPTION("wm97xx continuous touch driver for mainstone");
+MODULE_LICENSE("GPL");
Signature · 1 line
1.5.4
author
#14 lore raw

PATCH 1/1 Build system and MAINTAINERS entry for WM97xx touchscreen drivers

---
 MAINTAINERS                        |    9 ++++++
 drivers/input/touchscreen/Kconfig  |   52 ++++++++++++++++++++++++++++++++++++
 drivers/input/touchscreen/Makefile |    7 +++++
 3 files changed, 68 insertions(+), 0 deletions(-)
MAINTAINERS +9 -0
index 2340cfb..4ad793f 100644
@@ -4204,6 +4204,15 @@ L:	[email protected]
 W:	http://oops.ghostprotocols.net:81/blog
 S:	Maintained
 
+WM97XX TOUCHSCREEN DRIVERS
+P:	Mark Brown
+M:	[email protected]
+P:	Liam Girdwood
+M:	[email protected]
+L:	[email protected]
+T:	git git://opensource.wolfsonmicro.com/linux-2.6-touch
+S:	Supported
+
 X.25 NETWORK LAYER
 P:	Henner Eisen
 M:	[email protected]
drivers/input/touchscreen/Kconfig +52 -0

58 lines not on this page · raw message

drivers/input/touchscreen/Makefile +7 -0
index 35d4097..d38156e 100644
@@ -4,6 +4,8 @@
 
 # Each configuration option enables a list of files.
 
+wm97xx-ts-y := wm97xx-core.o
+
 obj-$(CONFIG_TOUCHSCREEN_ADS7846)	+= ads7846.o
 obj-$(CONFIG_TOUCHSCREEN_BITSY)		+= h3600_ts_input.o
 obj-$(CONFIG_TOUCHSCREEN_CORGI)		+= corgi_ts.o
@@ -19,3 +21,8 @@ obj-$(CONFIG_TOUCHSCREEN_PENMOUNT)	+= penmount.o
 obj-$(CONFIG_TOUCHSCREEN_TOUCHRIGHT)	+= touchright.o
 obj-$(CONFIG_TOUCHSCREEN_TOUCHWIN)	+= touchwin.o
 obj-$(CONFIG_TOUCHSCREEN_UCB1400)	+= ucb1400_ts.o
+obj-$(CONFIG_TOUCHSCREEN_WM97XX)	+= wm97xx-ts.o
+obj-$(CONFIG_TOUCHSCREEN_WM97XX_MAINSTONE)	+= mainstone-wm97xx.o
+wm97xx-ts-$(CONFIG_TOUCHSCREEN_WM9705)  += wm9705.o
+wm97xx-ts-$(CONFIG_TOUCHSCREEN_WM9712)  += wm9712.o
+wm97xx-ts-$(CONFIG_TOUCHSCREEN_WM9713)  += wm9713.o
Signature · 1 line
1.5.4
#15 lore raw
In reply to Mark Brown
Quoted 7 lines · Mark Brown

This patch series adds support for the touchscreen controllers provided by Wolfson Microelectronics WM97xx series chips in both polled and streaming modes.

Changes since last submission:
- Fix from Dmitry Baryshkov for build with CONFIG_PM. - Add the web site to the MAINTAINERS entry.

Thanks. This serie "worksforme". Is it going to be merged during this window?

Signature · 2 lines
With best wishes
Dmitry