hostapd with mac80211 and rt2500pci: hostapd doesn't receive clients EAPOL keys unless mon.wlan1 is promiscuous
Hi List,
I'm trying to get my rt2500pci running as an accesspoint. So far with only very limited success. I'm running the most recent stuff from git.wireless-testing (mac80211-v2.6.25_rc5_2623_g7556b76_080322-1). I've applied these patches from Johannes Berg:
006-mac80211-sparse-check-endianness-by-default.patch 008-allow-ap-vlan-modes.patch
009-mac80211-allow-wds.patch
I've tried running hostapd-0.6.2 (patched for nl80211) up to 0.6.4, all with the same results.
This is the problem, as far as I understand it:
hostapd doesn't receive the EAPOL key from the laptop that is trying to connect (thinkpad x61s, 00:1b:77:a4:db:26. I've tried connecting from both fedora8, and windows Vista). While ethereal shows that EAPOL keys are being sent by the thinkpad. This is what hostapd lists:
wlan1: STA 00:1b:77:a4:db:26 WPA: sending 1/4 msg of 4-Way Handshake
WPA: Send EAPOL(version=1 secure=0 mic=0 ack=1 install=0 pairwise=8 kde_len=0 keyidx=0 encr=0)
wlan1: STA 00:1b:77:a4:db:26 WPA: EAPOL-Key timeout
WPA: 00:1b:77:a4:db:26 WPA_PTK entering state PTKSTART
wlan1: STA 00:1b:77:a4:db:26 WPA: sending 1/4 msg of 4-Way Handshake
WPA: Send EAPOL(version=1 secure=0 mic=0 ack=1 install=0 pairwise=8 kde_len=0 keyidx=0 encr=0)
wlan1: STA 00:1b:77:a4:db:26 WPA: EAPOL-Key timeout
repeated quite a few times, before the thinkpad gives up trying to associate.
However, if I switch mon.wlan1 on the hostapd accesspoint to promiscuous, by issuing tethereal -i mon.wlan1, then suddenly hostapd does receive the EAPOL key from the think pad, and this happens (hostapd output):
wlan1: STA 00:1b:77:a4:db:26 WPA: sending 1/4 msg of 4-Way Handshake
WPA: Send EAPOL(version=1 secure=0 mic=0 ack=1 install=0 pairwise=8 kde_len=0 keyidx=0 encr=0)
IEEE 802.1X: 123 bytes from 00:1b:77:a4:db:26
IEEE 802.1X: version=1 type=3 length=119
wlan1: STA 00:1b:77:a4:db:26 WPA: received EAPOL-Key frame (2/4 Pairwise)
WPA: 00:1b:77:a4:db:26 WPA_PTK entering state PTKCALCNEGOTIATING
WPA: PTK derivation - A1=00:0c:f6:14:05:19 A2=00:1b:77:a4:db:26
WPA: PMK - hexdump(len=32): [REMOVED]
WPA: PTK - hexdump(len=64): [REMOVED]
WPA: 00:1b:77:a4:db:26 WPA_PTK entering state PTKCALCNEGOTIATING2
WPA: 00:1b:77:a4:db:26 WPA_PTK entering state PTKINITNEGOTIATING
so, now hostapd does receive a keyframe from the thinkpad. Unfortunately hostapd hangs after "WPA_PTK entering state PTKINITNEGOTIATING", and can only be terminated with a ctrl-c. In the past (one month ago, hostapd would continue, and it was actually possible to connect the thinkpad to hostapd, however I could never connect without making either mon.wlan1 or wlan1 promiscuous by running ethereal on it, and even then I'd get some kernel OOPSES on heavy traffic). This is the tethereal -i mon.wlan1 output (thinkpad=IntelCor_a4:db:26, hostapd=SitecomE_14:05:19):
17.034743 SitecomE_14:05:19 -> IntelCor_a4:db:26 EAPOL Key 17.034747 SitecomE_14:05:19 -> IntelCor_a4:db:26 EAPOL Key 17.051720 IntelCor_a4:db:26 -> SitecomE_14:05:19 EAPOL Key 27.050899 IntelCor_a4:db:26 -> SitecomE_14:05:19 IEEE 802.11
Disassociate, SN=3012, FN=0, Flags=........
27.051921 IntelCor_a4:db:26 -> SitecomE_14:05:19 IEEE 802.11
Disassociate, SN=3012, FN=0, Flags=....R...
27.080414 IntelCor_a4:db:26 -> SitecomE_14:05:19 IEEE 802.11 Null
function (No data), SN=3013, FN=0, Flags=...P...T
27.264342 IntelCor_a4:db:26 -> SitecomE_14:05:19 IEEE 802.11 Null
function (No data), SN=3014, FN=0, Flags=.......T
27.265133 IntelCor_a4:db:26 -> SitecomE_14:05:19 IEEE 802.11 QoS Null
function (No data), SN=3014, FN=0, Flags=....R..T
The QoS and Null function stuff continues more or less forever.
Ok, to summarize: hostapd doesn't seem to work at the moment with rt2500pci and lates git.wireless-testing. The cause seems to be that EOPOL key send from the client does not arrive at hostapd. This can be 'fixed' by running tethereal on the monitor interface. Any thoughts on what might cause this?
thanks for your time!
best regards,
Bas Hulsken
some additional info:
--------------------------------------------------------------
hostapd.conf:
--------------------------------------------------------------
interface=wlan1
driver=nl80211
logger_syslog=-1
logger_syslog_level=0
logger_stdout=-1
logger_stdout_level=0
dump_file=/tmp/hostapd.dump
ctrl_interface=/var/run/hostapd
ctrl_interface_group=0
ssid=steadydecline
country_code=NL
hw_mode=g
channel=1
beacon_int=100
dtim_period=2
max_num_sta=255
rts_threshold=2347
fragm_threshold=2346
macaddr_acl=0
accept_mac_file=/etc/hostapd.accept
deny_mac_file=/etc/hostapd.deny
auth_algs=3
ignore_broadcast_ssid=0
wme_enabled=1
wme_ac_bk_cwmin=4
wme_ac_bk_cwmax=10
wme_ac_bk_aifs=7
wme_ac_bk_txop_limit=0
wme_ac_bk_acm=0
wme_ac_be_aifs=3
wme_ac_be_cwmin=4
wme_ac_be_cwmax=10
wme_ac_be_txop_limit=0
wme_ac_be_acm=0
wme_ac_vi_aifs=2
wme_ac_vi_cwmin=3
wme_ac_vi_cwmax=4
wme_ac_vi_txop_limit=94
wme_ac_vi_acm=0
wme_ac_vo_aifs=2
wme_ac_vo_cwmin=2
wme_ac_vo_cwmax=3
wme_ac_vo_txop_limit=47
wme_ac_vo_acm=0
#ieee8021x=0
eapol_version=1
eap_message=hello
eapol_key_index_workaround=0
own_ip_addr=127.0.0.1
wpa=1
wpa_passphrase=***********
wpa_key_mgmt=WPA-PSK
wpa_pairwise=TKIP
supported_rates=10 20 55 110
wpa_group_rekey=600
wpa_strict_rekey=1
wpa_gmk_rekey=86400
--------------------------------------------------------------
ifcfg-wlan1
--------------------------------------------------------------
# RaLink RT2500 802.11g Cardbus/mini-PCI
DEVICE=wlan1
ONBOOT=no
HWADDR=00:0c:f6:14:05:19
BROADCAST=192.168.3.255
IPADDR=192.168.3.1
NETMASK=255.255.255.0
NETWORK=192.168.3.0
IPV6INIT=no
MODE=Master
BOOTPROTO=none
TYPE=Wireless
ESSID=steadydecline
#WIRELESS_RTS=on
RATE=AUTO
MODE=AUTO
CHANNEL=1
--------------------------------------------------------------
iwconfig
--------------------------------------------------------------
wmaster0 no wireless extensions.
wlan1 IEEE 802.11 ESSID:"steadydecline"
Mode:Master Frequency:2.412 GHz Tx-Power=23 dBm
Retry min limit:7 RTS thr=2347 B Fragment thr=2346 B
Encryption key:off
Link Quality:0 Signal level:0 Noise level:0 Rx invalid nwid:0 Rx invalid crypt:0 Rx invalid frag:0
Tx excessive retries:0 Invalid misc:0 Missed beacon:0
mon.wlan1 IEEE 802.11 Mode:Monitor Frequency:2.412 GHz Tx-Power=23 dBm
Retry min limit:7 RTS thr=2347 B Fragment thr=2346 B
Encryption key:off
Link Quality:0 Signal level:0 Noise level:0
Rx invalid nwid:0 Rx invalid crypt:0 Rx invalid frag:0
Tx excessive retries:0 Invalid misc:0 Missed beacon:0
--------------------------------------------------------------
Johannes Berg
maintainerQuoted 6 lines
Ok, to summarize: hostapd doesn't seem to work at the moment with rt2500pci and lates git.wireless-testing. The cause seems to be that EOPOL key send from the client does not arrive at hostapd. This can be 'fixed' by running tethereal on the monitor interface. Any thoughts on what might cause this?
Can you stick a printk into the driver to print out
* the configured MAC address
* the filter flags configuration?
Whenever either changes.
johannes
Hi Johannes,
Quoted 11 lines · Johannes Berg
Quoted 5 lines
Ok, to summarize: hostapd doesn't seem to work at the moment with rt2500pci and lates git.wireless-testing. The cause seems to be that EOPOL key send from the client does not arrive at hostapd. This can be 'fixed' by running tethereal on the monitor interface. Any thoughts on what might cause this?
Can you stick a printk into the driver to print out
* the configured MAC address
* the filter flags configuration?Whenever either changes.
before I blow up the system, I guess this should do the trick? (remember, I'm not a kernel hacker ;-):
rt2500pci.c 2008-03-23 13:52:55.000000000 +0100 renamed from drivers/net/wireless/rt2x00/rt2500pci.c 2008-03-12 09:49:21.000000000 +0100 +4 -2
@@ -300,10 +300,11 @@ rt2x00pci_register_write(rt2x00dev, CSR14, reg); } - if (flags & CONFIG_UPDATE_MAC) + if (flags & CONFIG_UPDATE_MAC) { rt2x00pci_register_multiwrite(rt2x00dev, CSR3, conf->mac, sizeof(conf->mac)); - + printk(KERN_INFO "rt2500pci MAC changed: %s\n", mac2str(conf->mac)); + } if (flags & CONFIG_UPDATE_BSSID) rt2x00pci_register_multiwrite(rt2x00dev, CSR5, conf->bssid, sizeof(conf->bssid));
@@ -1767,6 +1768,7 @@ return; rt2x00dev->packet_filter = *total_flags; + printk(KERN_INFO "rt2500pci filter_flags: %d\n", rt2x00dev->packet_filter); /* * Start configuration steps. * Note that the version error will always be dropped
Quoted 1 line
johannes
oh.. btw, I also had to patch hostapd a bit.. it seemed trivial, but perhaps I'm just stupid. It seems that the NL80211_STA_STAT_* stuff in current wireless-testing has been renamed to NL80211_STA_INFO_*, so I renamed all occurrences of that in driver_nl80211.c. Was that ok? This is the patch I applied:
driver_nl80211.c 2008-03-22 17:28:39.000000000 +0100 renamed from hostapd/driver_nl80211.c 2008-03-18 13:53:20.000000000 +0100 +14 -14
@@ -598,11 +598,11 @@ struct nlattr *tb[NL80211_ATTR_MAX + 1]; struct genlmsghdr *gnlh = nlmsg_data(nlmsg_hdr(msg)); struct hostap_sta_driver_data *data = arg; - struct nlattr *stats[NL80211_STA_STAT_MAX + 1]; - static struct nla_policy stats_policy[NL80211_STA_STAT_MAX + 1] = { - [NL80211_STA_STAT_INACTIVE_TIME] = { .type = NLA_U32 }, - [NL80211_STA_STAT_RX_BYTES] = { .type = NLA_U32 }, - [NL80211_STA_STAT_TX_BYTES] = { .type = NLA_U32 }, + struct nlattr *stats[NL80211_STA_INFO_MAX + 1]; + static struct nla_policy stats_policy[NL80211_STA_INFO_MAX + 1] = { + [NL80211_STA_INFO_INACTIVE_TIME] = { .type = NLA_U32 }, + [NL80211_STA_INFO_RX_BYTES] = { .type = NLA_U32 }, + [NL80211_STA_INFO_TX_BYTES] = { .type = NLA_U32 }, }; nla_parse(tb, NL80211_ATTR_MAX, genlmsg_attrdata(gnlh, 0),
@@ -614,24 +614,24 @@ * the kernel starts sending station notifications. */ - if (!tb[NL80211_ATTR_STA_STATS]) { + if (!tb[NL80211_ATTR_STA_INFO]) { wpa_printf(MSG_DEBUG, "sta stats missing!"); return NL_SKIP; } - if (nla_parse_nested(stats, NL80211_STA_STAT_MAX, - tb[NL80211_ATTR_STA_STATS], + if (nla_parse_nested(stats, NL80211_STA_INFO_MAX, + tb[NL80211_ATTR_STA_INFO], stats_policy)) { wpa_printf(MSG_DEBUG, "failed to parse nested attributes!"); return NL_SKIP; } - if (stats[NL80211_STA_STAT_INACTIVE_TIME]) + if (stats[NL80211_STA_INFO_INACTIVE_TIME]) data->inactive_msec = - nla_get_u32(stats[NL80211_STA_STAT_INACTIVE_TIME]); - if (stats[NL80211_STA_STAT_RX_BYTES]) - data->rx_bytes = nla_get_u32(stats[NL80211_STA_STAT_RX_BYTES]); - if (stats[NL80211_STA_STAT_TX_BYTES]) - data->rx_bytes = nla_get_u32(stats[NL80211_STA_STAT_TX_BYTES]); + nla_get_u32(stats[NL80211_STA_INFO_INACTIVE_TIME]); + if (stats[NL80211_STA_INFO_RX_BYTES]) + data->rx_bytes = nla_get_u32(stats[NL80211_STA_INFO_RX_BYTES]); + if (stats[NL80211_STA_INFO_TX_BYTES]) + data->rx_bytes = nla_get_u32(stats[NL80211_STA_INFO_TX_BYTES]); return NL_SKIP; }
cheers,
Bas
Hi Johannes,
Quoted 2 lines · Bas Hulsken
before I blow up the system, I guess this should do the trick? (remember, I'm not a kernel hacker ;-):
ok.. so I decided to just give it a try.. seems to work, this is dmesg upon ifupping the interface:
phy0: Selected rate control algorithm 'pid'
Registered led device: rt2500pci-phy0:radio
rt2500pci MAC changed: 00:0c:f6:14:05:19
rt2500pci filter_flags: 2ADDRCONF(NETDEV_UP): wlan1: link is not ready
when I run hostapd, this is in dmesg:
rt2500pci MAC changed: 00:00:00:00:00:00
rt2500pci MAC changed: 00:0c:f6:14:05:19
rt2500pci MAC changed: 00:00:00:00:00:00
rt2500pci MAC changed: 00:0c:f6:14:05:19
rt2500pci filter_flags: 2
rt2500pci filter_flags: 0
rt2500pci MAC changed: 00:00:00:00:00:00
rt2500pci MAC changed: 00:0c:f6:14:05:19
rt2500pci filter_flags: 2
this is immediately on startup of hostapd, after that filter and MAC remain unchanged (at least if my printk catches everything).
thanks,
Bas
Hi Johannes,
don't mean to push you or anything, but I was wondering if you overlooked my last mail. You asked me to add some printk's to the rt2500pci driver to debug hostapd authentication failure. I did this, and these are the results:
upon ifupping the interface:
------------------------------------------------
phy0: Selected rate control algorithm 'pid'
Registered led device: rt2500pci-phy0:radio
rt2500pci MAC changed: 00:0c:f6:14:05:19
rt2500pci filter_flags: 2ADDRCONF(NETDEV_UP): wlan1: link is not ready
------------------------------------------------
when I run hostapd, this is in dmesg:
------------------------------------------------
rt2500pci MAC changed: 00:00:00:00:00:00
rt2500pci MAC changed: 00:0c:f6:14:05:19
rt2500pci MAC changed: 00:00:00:00:00:00
rt2500pci MAC changed: 00:0c:f6:14:05:19
rt2500pci filter_flags: 2
rt2500pci filter_flags: 0
rt2500pci MAC changed: 00:00:00:00:00:00
rt2500pci MAC changed: 00:0c:f6:14:05:19
rt2500pci filter_flags: 2
------------------------------------------------
this is immediately on startup of hostapd, after that filter and MAC remain unchanged (at least if my printk catches everything).
does this look ok to you? Does it explain why I can only receive EOPOL keys when in promiscuous mode?
thanks for your help,
Bas
Quoted 39 lines · Bas Hulsken
Hi Johannes,
Quoted 2 lines · Bas Hulsken
before I blow up the system, I guess this should do the trick? (remember, I'm not a kernel hacker ;-):
ok.. so I decided to just give it a try.. seems to work, this is dmesg upon ifupping the interface:
phy0: Selected rate control algorithm 'pid'
Registered led device: rt2500pci-phy0:radio
rt2500pci MAC changed: 00:0c:f6:14:05:19
rt2500pcifilter_flags: 2ADDRCONF(NETDEV_UP): wlan1: link is not readywhen I run hostapd, this is in dmesg:
rt2500pci MAC changed: 00:00:00:00:00:00
rt2500pci MAC changed: 00:0c:f6:14:05:19
rt2500pci MAC changed: 00:00:00:00:00:00
rt2500pci MAC changed: 00:0c:f6:14:05:19
rt2500pcifilter_flags: 2
rt2500pcifilter_flags: 0
rt2500pci MAC changed: 00:00:00:00:00:00
rt2500pci MAC changed: 00:0c:f6:14:05:19
rt2500pcifilter_flags: 2this is immediately on startup of hostapd, after that filter and MAC remain unchanged (at least if my printk catches everything).
thanks,
Bas--
To unsubscribe from this list: send the line "unsubscribe linux-wireless" in the body of a message to [email protected]
More majordomo info at http://vger.kernel.org/majordomo-info.html
Johannes Berg
maintainerHi Bas,
Quoted 4 lines
don't mean to push you or anything, but I was wondering if you overlooked my last mail. You asked me to add some printk's to the rt2500pci driver to debug hostapd authentication failure. I did this, and these are the results:
Sorry. I'm sure I read it but I must have forgotten, thanks for the note.
Quoted 15 lines
rt2500pci MAC changed: 00:0c:f6:14:05:19
rt2500pcifilter_flags: 2rt2500pci MAC changed: 00:00:00:00:00:00
rt2500pci MAC changed: 00:0c:f6:14:05:19
rt2500pci MAC changed: 00:00:00:00:00:00
rt2500pci MAC changed: 00:0c:f6:14:05:19
rt2500pcifilter_flags: 2
rt2500pcifilter_flags: 0
rt2500pci MAC changed: 00:00:00:00:00:00
rt2500pci MAC changed: 00:0c:f6:14:05:19
rt2500pcifilter_flags: 2
------------------------------------------------
this is immediately on startup of hostapd, after that filter and MAC remain unchanged (at least if my printk catches everything).
That looks pretty much expected.
Quoted 2 lines
does this look ok to you? Does it explain why I can only receive EOPOL keys when in promiscuous mode?
Unfortunately not, it's a bit weird. I think I'll probably have to run it myself to figure it out and do captures on the various interfaces.
johannes