clk: rs9: Fix I2C accessors
PATCH v4 1/1 clk: rs9: Fix I2C accessors
Add custom I2C accessors to this driver, since the regular I2C regmap ones do not generate the exact I2C transfers required by the chip. On I2C write, it is mandatory to send transfer length first, on read the chip returns the transfer length in first byte. Instead of always reading back 8 bytes, which is the default and also the size of the entire register file, set BCP register to 1 to read out 1 byte which is less wasteful.
---
V2: Fix endianness handling in rs9_regmap_i2c_read() i2c_transfer
V3: - Disable regcache, the driver does a couple of I2C writes on boot
and that is all, so it only adds complexity
- Set regmap max_register to RS9_REG_BCP which is the correct one
V4: - Do not use I2C_M_RECV_LEN due to overhead, it requires buffer 4
times the size of this devices' register file, just read two bytes via I2C
---
Cc: Alexander Stein <[email protected]>
Cc: Michael Turquette <[email protected]>
Cc: Stephen Boyd <[email protected]>
--- drivers/clk/clk-renesas-pcie.c | 65 ++++++++++++++++++++++++++++++++-- 1 file changed, 62 insertions(+), 3 deletions(-)
drivers/clk/clk-renesas-pcie.c +62 -3
@@ -90,13 +90,66 @@ static const struct regmap_access_table rs9_writeable_table = { .n_yes_ranges = ARRAY_SIZE(rs9_writeable_ranges), }; +static int rs9_regmap_i2c_write (void *context, +unsigned int reg,unsigned int val) +{ +struct i2c_client *i2c = context; +const u8 data[3 ] = { reg,1 , val }; +const int count =ARRAY_SIZE (data); +int ret; + + ret =i2c_master_send (i2c, data, count); +if (ret == count) +return 0 ; +else if (ret <0 ) +return ret; +else +return -EIO ; +} + +static int rs9_regmap_i2c_read (void *context, +unsigned int reg,unsigned int *val) +{ +struct i2c_client *i2c = context; +struct i2c_msg xfer[2 ]; +u8 txdata = reg; +u8 rxdata[2 ]; +int ret; + + xfer[0 ].addr = i2c->addr; + xfer[0 ].flags =0 ; + xfer[0 ].len =1 ; + xfer[0 ].buf = (void *)&txdata; + + xfer[1 ].addr = i2c->addr; + xfer[1 ].flags =I2C_M_RD ; + xfer[1 ].len =2 ; + xfer[1 ].buf = (void *)rxdata; + + ret =i2c_transfer (i2c->adapter, xfer,2 ); +if (ret <0 ) +return ret; +if (ret !=2 ) +return -EIO ; + +/* +* Byte 0 is transfer length, which is always 1 due +* to BCP register programming to 1 in rs9_probe(), +* ignore it and use data from Byte 1. +*/ + *val = rxdata[1 ]; +return 0 ; +} +static const struct regmap_config rs9_regmap_config = { .reg_bits =8 , .val_bits =8 , - .cache_type =REGCACHE_FLAT , - .max_register =0x8 , + .cache_type =REGCACHE_NONE , + .max_register =RS9_REG_BCP , .rd_table = &rs9_readable_table, .wr_table = &rs9_writeable_table, + .reg_write = rs9_regmap_i2c_write, + .reg_read = rs9_regmap_i2c_read, };static int rs9_get_output_config (struct rs9_driver_data *rs9,int idx)
@@ -242,11 +295,17 @@ static int rs9_probe(struct i2c_client *client)return ret; } - rs9->regmap =devm_regmap_init_i2c (client, &rs9_regmap_config); + rs9->regmap =devm_regmap_init (&client->dev,NULL , + client, &rs9_regmap_config);if (IS_ERR (rs9->regmap))return dev_err_probe (&client->dev,PTR_ERR (rs9->regmap),"Failed to allocate register map\n" ); +/* Always read back 1 Byte via I2C */ + ret =regmap_write (rs9->regmap,RS9_REG_BCP ,1 ); +if (ret <0 ) +return ret; +/* Register clock */ for (i =0 ; i < rs9->chip_info->num_clks; i++) {snprintf (name,5 ,"DIF%d" , i);
Signature · 1 line
2.35.1
Hi Marek,
Am Donnerstag, 29. September 2022, 21:55:21 CEST schrieb Marek Vasut:
Quoted 31 lines
Add custom I2C accessors to this driver, since the regular I2C regmap ones do not generate the exact I2C transfers required by the chip. On I2C write, it is mandatory to send transfer length first, on read the chip returns the transfer length in first byte. Instead of always reading back 8 bytes, which is the default and also the size of the entire register file, set BCP register to 1 to read out 1 byte which is less wasteful.
Fixes 892e0ddea1aa ("clk: rs9: Add Renesas 9-series PCIe clock generatordriver") Reported-by: Alexander Stein <[email protected]>
Signed-off-by Marek Vasut <[email protected]>---
V2: Fix endianness handling inrs9_regmap_i2c_read()i2c_transfer
V3: - Disable regcache, the driver does a couple of I2C writes on boot
and that is all, so it only adds complexity
- Set regmapmax_registertoRS9_REG_BCPwhich is the correct one
V4: - Do not useI2C_M_RECV_LENdue to overhead, it requires buffer 4
times the size of this devices' register file, just read two bytes via I2C
---
Cc: Alexander Stein <[email protected]>
Cc: Michael Turquette <[email protected]>
Cc: Stephen Boyd <[email protected]>--- drivers/clk/clk-renesas-pcie.c | 65 ++++++++++++++++++++++++++++++++-- 1 file changed, 62 insertions(+), 3 deletions(-)drivers/clk/clk-renesas-pcie.c +0
-0
drivers/clk/clk-renesas-pcie.c static const struct regmap_access_table · line 94
Quoted 5 lines
drivers/clk/clk-renesas-pcie.c +2
-0@@ -90,13 +90,66 @@ static const struct regmap_access_table rs9_writeable_table = { .n_yes_ranges = ARRAY_SIZE(rs9_writeable_ranges), }; +static int rs9_regmap_i2c_write (void *context, + unsigned int reg, unsigned int
val)
Quoted 35 lines
drivers/clk/clk-renesas-pcie.c +35
-0+{ +struct i2c_client *i2c = context; +const u8 data[3 ] = { reg,1 , val }; +const int count =ARRAY_SIZE (data); +int ret; + + ret =i2c_master_send (i2c, data, count); +if (ret == count) +return 0 ; +else if (ret <0 ) +return ret; +else +return -EIO ; +} + +static int rs9_regmap_i2c_read (void *context, +unsigned int reg,unsigned int *val) +{ +struct i2c_client *i2c = context; +struct i2c_msg xfer[2 ]; +u8 txdata = reg; +u8 rxdata[2 ]; +int ret; + + xfer[0 ].addr = i2c->addr; + xfer[0 ].flags =0 ; + xfer[0 ].len =1 ; + xfer[0 ].buf = (void *)&txdata; + + xfer[1 ].addr = i2c->addr; + xfer[1 ].flags =I2C_M_RD ; + xfer[1 ].len =2 ; + xfer[1 ].buf = (void *)rxdata; + + ret =i2c_transfer (i2c->adapter, xfer,2 );
drivers/clk/clk-renesas-pcie.c static const struct regmap_access_table rs9_writeable_table = { · line 139
Quoted 10 lines
drivers/clk/clk-renesas-pcie.c +10
-0+if (ret <0 ) +return ret; +if (ret !=2 ) +return -EIO ; + +/* +* Byte 0 is transfer length, which is always 1 due +* to BCP register programming to 1 in rs9_probe(), +* ignore it and use data from Byte 1. +*/
This comments only holds true until cache is enabled again. Cache is initialized by from reading registers using this function before BCP is set :) Anyway, that's good for now:
Quoted 19 lines
drivers/clk/clk-renesas-pcie.c +8
-2+ *val = rxdata[1 ]; +return 0 ; +} +static const struct regmap_config rs9_regmap_config = { .reg_bits =8 , .val_bits =8 , - .cache_type =REGCACHE_FLAT , - .max_register =0x8 , + .cache_type =REGCACHE_NONE , + .max_register =RS9_REG_BCP , .rd_table = &rs9_readable_table, .wr_table = &rs9_writeable_table, + .reg_write = rs9_regmap_i2c_write, + .reg_read = rs9_regmap_i2c_read, };static int rs9_get_output_config (struct rs9_driver_data *rs9,int idx)
drivers/clk/clk-renesas-pcie.c static int rs9_probe(struct i2c_client *client) · line 299
Quoted 6 lines
drivers/clk/clk-renesas-pcie.c +2
-1@@ -242,11 +295,17 @@ static int rs9_probe(struct i2c_client *client)return ret; } - rs9->regmap =devm_regmap_init_i2c (client, &rs9_regmap_config); + rs9->regmap = devm_regmap_init(&client->dev, NULL, + client,
&rs9_regmap_config);
drivers/clk/clk-renesas-pcie.c static int rs9_probe(struct i2c_client *client)
Quoted 3 lines
drivers/clk/clk-renesas-pcie.c +0
-0if (IS_ERR (rs9->regmap)) return dev_err_probe(&client->dev, PTR_ERR(rs9->regmap), "Failed to allocate register
map\n");
Quoted 9 lines
drivers/clk/clk-renesas-pcie.c +5
-0+/* Always read back 1 Byte via I2C */ + ret =regmap_write (rs9->regmap,RS9_REG_BCP ,1 ); +if (ret <0 ) +return ret; +/* Register clock */ for (i =0 ; i < rs9->chip_info->num_clks; i++) {snprintf (name,5 ,"DIF%d" , i);
Quoting Marek Vasut (2022-09-29 12:55:21)
Quoted 11 lines
Add custom I2C accessors to this driver, since the regular I2C regmap ones do not generate the exact I2C transfers required by the chip. On I2C write, it is mandatory to send transfer length first, on read the chip returns the transfer length in first byte. Instead of always reading back 8 bytes, which is the default and also the size of the entire register file, set BCP register to 1 to read out 1 byte which is less wasteful.
Fixes 892e0ddea1aa ("clk: rs9: Add Renesas 9-series PCIe clock generator driver")Reported-by Alexander Stein <[email protected]>Signed-off-by Marek Vasut <[email protected]>---
Applied to clk-fixes