Enable CODEC POST with CFG_POST_CODEC rather than with CFG_POST_DSP.
PATCH 1/1 Enable CODEC POST with CFG_POST_CODEC rather than with CFG_POST_DSP.
From: Yuri Tikhonov <[email protected]>
Signed-off-by Dmitry Rakhchev <[email protected]>
--- post/tests.c | 2 +- 1 files changed, 1 insertions(+), 1 deletions(-)
post/tests.c +1 -1
@@ -225,7 +225,7 @@ struct post_test post_list[] = CFG_POST_DSP },#endif -#if CONFIG_POST &CFG_POST_DSP +#if CONFIG_POST &CFG_POST_CODEC {"CODEC test" , "codec",
Signature · 1 line
1.5.4.2
PATCH 1/1 The patch adds new POST tests for the Lwmon5 board.
From: Yuri Tikhonov <[email protected]>
* External Watchdog test;
* dsPIC tests;
* FPGA test;
* GDC test;
* Sysmon tests.
Signed-off-by Dmitry Rakhchev <[email protected]>
Signed-off-by Yuri Tikhonov <[email protected]>
--- board/lwmon5/lwmon5.c | 19 +++ include/configs/lwmon5.h | 92 ++++++++++++++- include/post.h | 5 + include/ppc440.h | 3 + post/board/lwmon5/Makefile | 28 +++++ post/board/lwmon5/dsp.c | 58 +++++++++ post/board/lwmon5/dspic.c | 109 +++++++++++++++++ post/board/lwmon5/fpga.c | 104 ++++++++++++++++ post/board/lwmon5/gdc.c | 94 +++++++++++++++ post/board/lwmon5/sysmon.c | 265 ++++++++++++++++++++++++++++++++++++++++++ post/board/lwmon5/watchdog.c | 132 +++++++++++++++++++++ post/tests.c | 26 ++++ 12 files changed, 931 insertions(+), 4 deletions(-) create mode 100644 post/board/lwmon5/Makefile create mode 100644 post/board/lwmon5/dsp.c create mode 100644 post/board/lwmon5/dspic.c create mode 100644 post/board/lwmon5/fpga.c create mode 100644 post/board/lwmon5/gdc.c create mode 100644 post/board/lwmon5/sysmon.c create mode 100644 post/board/lwmon5/watchdog.c
board/lwmon5/lwmon5.c +19 -0
@@ -96,6 +96,25 @@ int board_early_init_f(void)gpio_write_bit (CFG_GPIO_FLASH_WP ,1 ); +#if CONFIG_POST &CFG_POST_BSPEC1 +gpio_write_bit (CFG_GPIO_HIGHSIDE ,1 ); + + reg =0 ;/* reuse as counter */ +out_be32 ((void *)CFG_DSPIC_TEST_ADDR , +in_be32 ((void *)CFG_DSPIC_TEST_ADDR ) + & ~CFG_DSPIC_TEST_MASK ); +while (!gpio_read_in_bit (CFG_GPIO_DSPIC_READY ) && reg++ <1000 ) { +udelay (1000 ); + } +gpio_write_bit (CFG_GPIO_HIGHSIDE ,0 ); +if (gpio_read_in_bit (CFG_GPIO_DSPIC_READY )) { +/* set "boot error" flag */ +out_be32 ((void *)CFG_DSPIC_TEST_ADDR , +in_be32 ((void *)CFG_DSPIC_TEST_ADDR ) | +CFG_DSPIC_TEST_MASK ); + } +#endif +/* * Reset PHY's: * The PHY's need a 2nd reset pulse, since the MDIO address is latched
include/configs/lwmon5.h +88 -4
126 lines not on this page · raw message
include/post.h +5 -0
@@ -93,6 +93,11 @@ extern int post_hotkeys_pressed(void);#define CFG_POST_CODEC 0x00002000#define CFG_POST_FPU 0x00004000#define CFG_POST_ECC 0x00008000 +#define CFG_POST_BSPEC1 0x00010000 +#define CFG_POST_BSPEC2 0x00020000 +#define CFG_POST_BSPEC3 0x00040000 +#define CFG_POST_BSPEC4 0x00080000 +#define CFG_POST_BSPEC5 0x00100000#endif /* CONFIG_POST */
include/ppc440.h +3 -0
@@ -1431,6 +1431,9 @@#define SDR0_MFR_PKT_REJ_POL 0x00200000/* Packet Reject Polarity */ #define GPT0_COMP6 0x00000098 +#define GPT0_COMP5 0x00000094 +#define GPT0_COMP4 0x00000090 +#define GPT0_COMP3 0x0000008C#if defined(CONFIG_440EPX ) || defined(CONFIG_440GRX )#define SDR0_USB2D0CR 0x0320
post/board/lwmon5/Makefile new file +28 -0
@@ -0,0 +1,28 @@ +# +# (C) Copyright 2008 Dmitry Rakhchev, EmCraft Systems, rda at emcraft.com +# +# Developed for DENX Software Engineering GmbH +# +# See file CREDITS for list of people who contributed to this +# project. +# +# This program is free software; you can redistribute it and/or +# modify it under the terms of the GNU General Public License as +# published by the Free Software Foundation; either version 2 of +# the License, or (at your option) any later version. +# +# This program is distributed in the hope that it will be useful, +# but WITHOUT ANY WARRANTY; without even the implied warranty of +# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the +# GNU General Public License for more details. +# +# You should have received a copy of the GNU General Public License +# along with this program; if not, write to the Free Software +# Foundation, Inc., 59 Temple Place, Suite 330, Boston, +# MA 02111-1307 USA + +LIB = libpostlwmon5.a + +COBJS = sysmon.o watchdog.o dspic.o fpga.o dsp.o gdc.o + +include $(TOPDIR)/post/rules.mk
post/board/lwmon5/dsp.c new file +58 -0
58 lines not on this page · raw message
post/board/lwmon5/dspic.c new file +109 -0
109 lines not on this page · raw message
post/board/lwmon5/fpga.c new file +104 -0
104 lines not on this page · raw message
post/board/lwmon5/gdc.c new file +94 -0
94 lines not on this page · raw message
post/board/lwmon5/sysmon.c new file +265 -0
265 lines not on this page · raw message
post/board/lwmon5/watchdog.c new file +132 -0
132 lines not on this page · raw message
post/tests.c +26 -0
@@ -48,6 +48,13 @@ extern int dsp_post_test (int flags);extern int codec_post_test (int flags);extern int ecc_post_test (int flags); +extern int dspic_init_post_test (int flags); +extern int dspic_post_test (int flags); +extern int gdc_post_test (int flags); +extern int fpga_post_test (int flags); +extern int lwmon5_watchdog_post_test (int flags); +extern int sysmon1_post_test (int flags); +extern int sysmon_init_f (void );extern void sysmon_reloc (void );
@@ -68,6 +75,9 @@ struct post_test post_list[] = },#endif #if CONFIG_POST & CFG_POST_WATCHDOG +#if defined(CONFIG_POST_WATCHDOG) + CONFIG_POST_WATCHDOG, +#else { "Watchdog timer test", "watchdog",
@@ -79,6 +89,7 @@ struct post_test post_list[] = CFG_POST_WATCHDOG },#endif +#endif #if CONFIG_POST &CFG_POST_I2C { "I2C test",
@@ -249,6 +260,21 @@ struct post_test post_list[] = CFG_POST_ECC },#endif +#if CONFIG_POST &CFG_POST_BSPEC1 + CONFIG_POST_BSPEC1, +#endif +#if CONFIG_POST &CFG_POST_BSPEC2 + CONFIG_POST_BSPEC2, +#endif +#if CONFIG_POST &CFG_POST_BSPEC3 + CONFIG_POST_BSPEC3, +#endif +#if CONFIG_POST &CFG_POST_BSPEC4 + CONFIG_POST_BSPEC4, +#endif +#if CONFIG_POST &CFG_POST_BSPEC4 + CONFIG_POST_BSPEC5, +#endif };unsigned int post_list_size =sizeof (post_list) /sizeof (struct post_test );
Signature · 1 line
1.5.4.2
PATCH 1/1 The patch introduces the CRITICAL feature of POST tests. If the test
From: Yuri Tikhonov <[email protected]>
Signed-off-by Dmitry Rakhchev <[email protected]>
Signed-off-by Yuri Tikhonov <[email protected]>
--- common/main.c | 8 +++++++- include/asm-arm/global_data.h | 1 + include/asm-avr32/global_data.h | 1 + include/asm-blackfin/global_data.h | 1 + include/asm-i386/global_data.h | 1 + include/asm-m68k/global_data.h | 1 + include/asm-microblaze/global_data.h | 1 + include/asm-mips/global_data.h | 1 + include/asm-nios/global_data.h | 1 + include/asm-nios2/global_data.h | 1 + include/asm-ppc/global_data.h | 1 + include/asm-sh/global_data.h | 1 + include/post.h | 4 ++++ post/post.c | 18 +++++++++++++++--- 14 files changed, 37 insertions(+), 4 deletions(-)
common/main.c +7 -1
@@ -40,7 +40,7 @@#include <post.h> -#ifdef CONFIG_SILENT_CONSOLE +#if defined(CONFIG_SILENT_CONSOLE ) || defined(CONFIG_POST )DECLARE_GLOBAL_DATA_PTR ;#endif
@@ -369,6 +369,12 @@ void main_loop (void)init_cmd_timeout ();# endif /* CONFIG_BOOT_RETRY_TIME */ +#ifdef CONFIG_POST +if (gd->flags &GD_FLG_POSTFAIL ) { + s =getenv ("failbootcmd" ); + } + else +#endif /* CONFIG_POST */ #ifdef CONFIG_BOOTCOUNT_LIMIT if (bootlimit && (bootcount > bootlimit)) { printf ("Warning: Bootlimit (%u) exceeded. Using altbootcmd.\n",
include/asm-arm/global_data.h +1 -0
@@ -60,6 +60,7 @@ typedef struct global_data {#define GD_FLG_RELOC 0x00001/* Code was relocated to RAM */ #define GD_FLG_DEVINIT 0x00002/* Devices have been initialized */ #define GD_FLG_SILENT 0x00004/* Silent mode */ +#define GD_FLG_POSTFAIL 0x00008/* Critical POST test failed */ #define DECLARE_GLOBAL_DATA_PTR register volatile gd_t *gd asm ("r8")
include/asm-avr32/global_data.h +1 -0
@@ -51,6 +51,7 @@ typedef struct global_data {#define GD_FLG_RELOC 0x00001/* Code was relocated to RAM */ #define GD_FLG_DEVINIT 0x00002/* Devices have been initialized */ #define GD_FLG_SILENT 0x00004/* Silent mode */ +#define GD_FLG_POSTFAIL 0x00008/* Critical POST test failed */ #define DECLARE_GLOBAL_DATA_PTR register gd_t *gd asm("r5")
include/asm-blackfin/global_data.h +1 -0
@@ -61,6 +61,7 @@ typedef struct global_data {#define GD_FLG_RELOC 0x00001/* Code was relocated to RAM */ #define GD_FLG_DEVINIT 0x00002/* Devices have been initialized */ #define GD_FLG_SILENT 0x00004/* Silent mode */ +#define GD_FLG_POSTFAIL 0x00008/* Critical POST test failed */ #define DECLARE_GLOBAL_DATA_PTR register gd_t * volatile gd asm ("P5")
include/asm-i386/global_data.h +1 -0
@@ -54,6 +54,7 @@ typedef struct {#define GD_FLG_RELOC 0x00001/* Code was relocated to RAM */ #define GD_FLG_DEVINIT 0x00002/* Devices have been initialized */ #define GD_FLG_SILENT 0x00004/* Silent mode */ +#define GD_FLG_POSTFAIL 0x00008/* Critical POST test failed */ extern gd_t *global_data;
include/asm-m68k/global_data.h +1 -0
@@ -68,6 +68,7 @@ typedef struct global_data {#define GD_FLG_RELOC 0x00001/* Code was relocated to RAM */ #define GD_FLG_DEVINIT 0x00002/* Devices have been initialized */ #define GD_FLG_SILENT 0x00004/* Silent mode */ +#define GD_FLG_POSTFAIL 0x00008/* Critical POST test failed */ #if 0 extern gd_t *global_data;
include/asm-microblaze/global_data.h +1 -0
@@ -52,6 +52,7 @@ typedef struct global_data {#define GD_FLG_RELOC 0x00001/* Code was relocated to RAM */ #define GD_FLG_DEVINIT 0x00002/* Devices have been initialized */ #define GD_FLG_SILENT 0x00004/* Silent mode */ +#define GD_FLG_POSTFAIL 0x00008/* Critical POST test failed */ #define DECLARE_GLOBAL_DATA_PTR register volatile gd_t *gd asm ("r31")
include/asm-mips/global_data.h +1 -0
@@ -54,6 +54,7 @@ typedef struct global_data {#define GD_FLG_RELOC 0x00001/* Code was relocated to RAM */ #define GD_FLG_DEVINIT 0x00002/* Devices have been initialized */ #define GD_FLG_SILENT 0x00004/* Silent mode */ +#define GD_FLG_POSTFAIL 0x00008/* Critical POST test failed */ #define DECLARE_GLOBAL_DATA_PTR register volatile gd_t *gd asm ("k0")
include/asm-nios/global_data.h +1 -0
@@ -45,6 +45,7 @@ typedef struct global_data {#define GD_FLG_RELOC 0x00001/* Code was relocated to RAM */ #define GD_FLG_DEVINIT 0x00002/* Devices have been initialized */ #define GD_FLG_SILENT 0x00004/* Silent mode */ +#define GD_FLG_POSTFAIL 0x00008/* Critical POST test failed */ #define DECLARE_GLOBAL_DATA_PTR register gd_t *gd asm ("%g7")
include/asm-nios2/global_data.h +1 -0
@@ -44,6 +44,7 @@ typedef struct global_data {#define GD_FLG_RELOC 0x00001/* Code was relocated to RAM */ #define GD_FLG_DEVINIT 0x00002/* Devices have been initialized */ #define GD_FLG_SILENT 0x00004/* Silent mode */ +#define GD_FLG_POSTFAIL 0x00008/* Critical POST test failed */ #define DECLARE_GLOBAL_DATA_PTR register gd_t *gd asm ("r15")
include/asm-ppc/global_data.h +1 -0
@@ -164,6 +164,7 @@ typedef struct global_data {#define GD_FLG_RELOC 0x00001/* Code was relocated to RAM */ #define GD_FLG_DEVINIT 0x00002/* Devices have been initialized */ #define GD_FLG_SILENT 0x00004/* Silent mode */ +#define GD_FLG_POSTFAIL 0x00008/* Critical POST test failed */ #if 1 #define DECLARE_GLOBAL_DATA_PTR register volatile gd_t *gd asm ("r2")
include/asm-sh/global_data.h +1 -0
@@ -44,6 +44,7 @@ typedef struct global_data#define GD_FLG_RELOC 0x00001/* Code was relocated to RAM */ #define GD_FLG_DEVINIT 0x00002/* Devices have been initialized */ #define GD_FLG_SILENT 0x00004/* Silent mode */ +#define GD_FLG_POSTFAIL 0x00008/* Critical POST test failed */ #define DECLARE_GLOBAL_DATA_PTR register gd_t *gd asm ("r13")
include/post.h +4 -0
@@ -42,12 +42,16 @@#define POST_REBOOT 0x0800/* test may cause rebooting */ #define POST_PREREL 0x1000/* test runs before relocation */ +#define POST_CRITICAL 0x2000/* Use failbootcmd if test failed */ +#define POST_MEM (POST_RAM | POST_ROM)#define POST_ALWAYS (POST_NORMAL | \ POST_SLOWTEST | \ POST_MANUAL | \ POST_POWERON ) +#define POST_FAIL_SAVE 0x80 +#ifndef __ASSEMBLY__ struct post_test {
post/post.c +15 -3
@@ -157,8 +157,10 @@ static void post_bootmode_test_off (void)static void post_get_flags (int *test_flags) { -int flag[] = {POST_POWERON ,POST_NORMAL ,POST_SLOWTEST }; -char *var[] = {"post_poweron" ,"post_normal" ,"post_slowtest" }; +int flag[] = {POST_POWERON ,POST_NORMAL ,POST_SLOWTEST , +POST_CRITICAL }; +char *var[] = {"post_poweron" ,"post_normal" ,"post_slowtest" , +"post_critical" };int varnum =sizeof (var) /sizeof (var[0 ]);char list[128 ];/* long enough for POST list */ char *name;
@@ -224,7 +226,9 @@ static int post_run_single (struct post_test *test,if (!(flags &POST_REBOOT )) {if ((test_flags &POST_REBOOT ) && !(flags &POST_MANUAL )) { -post_bootmode_test_on (i); +post_bootmode_test_on ( + (gd->flags &GD_FLG_POSTFAIL ) ? +POST_FAIL_SAVE | i : i); }if (test_flags &POST_PREREL )
@@ -236,10 +240,14 @@ static int post_run_single (struct post_test *test,if (test_flags &POST_PREREL ) {if ((*test->test) (flags) ==0 )post_log_mark_succ ( test->testid ); +else if (test_flags &POST_CRITICAL ) + gd->flags |=GD_FLG_POSTFAIL ; }else {if ((*test->test) (flags) !=0 ) {post_log ("FAILED\n" );show_boot_progress (-32 ); +if (test_flags &POST_CRITICAL ) + gd->flags |=GD_FLG_POSTFAIL ; }else post_log ("PASSED\n" );
@@ -266,6 +274,10 @@ int post_run (char *name, int flags)unsigned int last;if (post_bootmode_get (&last) &POST_POWERTEST ) { +if (last &POST_FAIL_SAVE ) { + last &= ~POST_FAIL_SAVE ; + gd->flags |=GD_FLG_POSTFAIL ; + }if (last < post_list_size && (flags & test_flags[last] &POST_ALWAYS ) && (flags & test_flags[last] &POST_MEM )) {
Signature · 1 line
1.5.4.2
PATCH 1/1 Some fixes to dspic, fpga, and gdc post tests for lwmon5.
From: Yuri Tikhonov <[email protected]>
Signed-off-by Dmitry Rakhchev <[email protected]>
Signed-off-by Yuri Tikhonov <[email protected]>
--- post/board/lwmon5/dspic.c | 2 +- post/board/lwmon5/fpga.c | 4 ++++ post/board/lwmon5/gdc.c | 2 +- 3 files changed, 6 insertions(+), 2 deletions(-)
post/board/lwmon5/dspic.c +1 -1
@@ -94,9 +94,9 @@ int dspic_post_test(int flags) } data =dspic_read (DSPIC_SYS_ERROR_REG ); -if (data !=0 ) ret =1 ;if (data ==-1 ) {post_log ("dsPIC : failed read system error\n" ); + ret =1 ; }else {post_log ("dsPIC SYS-ERROR code: 0x%04X\n" , data); }
post/board/lwmon5/fpga.c +4 -0
@@ -39,6 +39,7 @@ DECLARE_GLOBAL_DATA_PTR;#define FPGA_VERSION_REG 0xC4000040#define FPGA_RAM_START 0xC4200000#define FPGA_RAM_END 0xC4203FFF +#define FPGA_STAT 0xC400000C#define FPGA_PWM_CTRL_REG 0xC4000020#define FPGA_PWM_TV_REG 0xC4000024
@@ -93,6 +94,9 @@ int fpga_post_test(int flags)post_log ("FPGA : version %u.%u\n" , (version >>8 ) &0xFF , version &0xFF ); +/* Enable write to FPGA RAM */ +out_be32 ((void *)FPGA_STAT ,in_be32 ((void *)FPGA_STAT ) |0x1000 ); + read_value =get_ram_size ((void *)CFG_FPGA_BASE_1 ,0x4000 );post_log ("FPGA RAM size: %d bytes\n" , read_value);
post/board/lwmon5/gdc.c +1 -1
@@ -35,7 +35,7 @@DECLARE_GLOBAL_DATA_PTR ; -#define GDC_SCRATCH_REG 0xC1FF8044 +#define GDC_SCRATCH_REG 0xC1FF8008#define GDC_VERSION_REG 0xC1FF8084#define GDC_RAM_START 0xC0000000#define GDC_RAM_END 0xC2000000
Signature · 1 line
1.5.4.2
PATCH 1/1 Add support for the lwmon5 board reset via GPIO58.
From: Yuri Tikhonov <[email protected]>
Signed-off-by Dmitry Rakhchev <[email protected]>
Signed-off-by Yuri Tikhonov <[email protected]>
--- board/lwmon5/lwmon5.c | 5 +++++ include/configs/lwmon5.h | 2 ++ 2 files changed, 7 insertions(+), 0 deletions(-)
board/lwmon5/lwmon5.c +5 -0
@@ -594,3 +594,8 @@ void video_get_info_str (int line_number, char *info) }#endif #endif /* CONFIG_VIDEO */ + +void board_reset (void ) +{ +gpio_write_bit (CFG_GPIO_BOARD_RESET ,1 ); +}
include/configs/lwmon5.h +2 -0
@@ -36,6 +36,7 @@#define CONFIG_BOARD_EARLY_INIT_F 1/* Call board_early_init_f */ #define CONFIG_BOARD_POSTCLK_INIT 1/* Call board_postclk_init */ #define CONFIG_MISC_INIT_R 1/* Call misc_init_r */ +#define CONFIG_BOARD_RESET 1/* Call board_reset */ /*----------------------------------------------------------------------- * Base addresses -- Note these are effective addresses where the
@@ -516,6 +517,7 @@#define CFG_GPIO_EEPROM_EXT_WP 55#define CFG_GPIO_HIGHSIDE 56#define CFG_GPIO_EEPROM_INT_WP 57 +#define CFG_GPIO_BOARD_RESET 58#define CFG_GPIO_LIME_S 59#define CFG_GPIO_LIME_RST 60#define CFG_GPIO_SYSMON_STATUS 62
Signature · 1 line
1.5.4.2
PATCH 1/1 The patch introduces the alternative configuration of the log buffer for
From: Yuri Tikhonov <[email protected]>
To enable this, alternative, configuration the U-Boot board configuration
file for lwmon5 includes the definitions of alternative addresses for header (CONFIG_ALT_LH_ADDR) and buffer (CONFIG_ALT_LB_ADDR).
The Linux shall be configured with the CONFIG_ALT_LB_LOCATION option set,
and has the BOARD_ALT_LH_ADDR and BOARD_ALT_LB_ADDR constants defined in the lwmon5 board-specific header (arch/ppc/platforms/4xx/lwmon5.h).
Signed-off-by Yuri Tikhonov <[email protected]>
--- common/cmd_bootm.c | 4 ++++ common/cmd_log.c | 38 ++++++++++++++++++++++++++++++++------ include/configs/lwmon5.h | 2 ++ include/ppc440.h | 2 ++ lib_ppc/board.c | 4 ++++ 5 files changed, 44 insertions(+), 6 deletions(-)
common/cmd_bootm.c +4 -0
@@ -545,11 +545,15 @@ do_bootm_linux (cmd_tbl_t *cmdtp, int flag, }#ifdef CONFIG_LOGBUFFER +#ifndef CONFIG_ALT_LB_ADDR kbd=gd->bd;/* Prevent initrd from overwriting logbuffer */ if (initrd_high < (kbd->bi_memsize-LOGBUFF_LEN -LOGBUFF_OVERHEAD )) initrd_high = kbd->bi_memsize-LOGBUFF_LEN -LOGBUFF_OVERHEAD ;debug ("## Logbuffer at 0x%08lX " , kbd->bi_memsize-LOGBUFF_LEN ); +#else +debug ("## Logbuffer at 0x%08lX " ,CONFIG_ALT_LB_ADDR ); +#endif #endif /*
common/cmd_log.c +32 -6
@@ -59,14 +59,25 @@ static char buf[1024];static unsigned console_loglevel =3 ;static unsigned default_message_loglevel =4 ;static unsigned log_version =1 ; +#ifdef CONFIG_ALT_LB_ADDR +static volatile logbuff_t *log; +#else static logbuff_t *log; +#endif +static char *lbuf;void logbuff_init_ptrs (void ) {unsigned long tag, post_word;char *s; +#ifdef CONFIG_ALT_LB_ADDR + log = (logbuff_t *)CONFIG_ALT_LH_ADDR ; + lbuf = (char *)CONFIG_ALT_LB_ADDR ; +#else log = (logbuff_t *)(gd->bd->bi_memsize-LOGBUFF_LEN ) -1 ; + lbuf = log->buf; +#endif /* Set up log version */ if ((s =getenv ("logversion" )) !=NULL )
@@ -101,11 +112,26 @@ void logbuff_init_ptrs (void)void logbuff_reset (void ) { +#ifndef CONFIG_ALT_LB_ADDR memset (log,0 ,sizeof (logbuff_t)); -if (log_version ==2 ) +#endif +if (log_version ==2 ) { log->v2.tag =LOGBUFF_MAGIC ; -else +#ifdef CONFIG_ALT_LB_ADDR + log->v2.start =0 ; + log->v2.con =0 ; + log->v2.end =0 ; + log->v2.chars =0 ; +#endif + }else { log->v1.tag =LOGBUFF_MAGIC ; +#ifdef CONFIG_ALT_LB_ADDR + log->v1.dummy =0 ; + log->v1.start =0 ; + log->v1.size =0 ; + log->v1.chars =0 ; +#endif + } }int drv_logbuff_init (void )
@@ -188,7 +214,7 @@ int do_log (cmd_tbl_t *cmdtp, int flag, int argc, char *argv[]) size = log->v1.size; }for (i=0 ; i < (size&LOGBUFF_MASK ); i++) { - s = (char *)log->buf+((start+i)&LOGBUFF_MASK ); + s = lbuf+((start+i)&LOGBUFF_MASK );putc (*s); }return 0 ;
@@ -196,7 +222,7 @@ int do_log (cmd_tbl_t *cmdtp, int flag, int argc, char *argv[])logbuff_reset ();return 0 ; }else if (strcmp (argv[1 ],"info" ) ==0 ) { -printf ("Logbuffer at %08lx\n" , (unsigned long )log->buf); +printf ("Logbuffer at %08lx\n" , (unsigned long )lbuf);if (log_version ==2 ) {printf ("log_start = %08lx\n" , log->v2.start);printf ("log_end = %08lx\n" , log->v2.end);
@@ -257,14 +283,14 @@ static int logbuff_printk(const char *line) line_feed =0 ;for (; p < buf_end; p++) {if (log_version ==2 ) { - log->buf[log->v2.end &LOGBUFF_MASK ] = *p; + lbuf[log->v2.end &LOGBUFF_MASK ] = *p; log->v2.end++;if (log->v2.end - log->v2.start >LOGBUFF_LEN ) log->v2.start++; log->v2.chars++; }else { - log->buf[(log->v1.start + log->v1.size) & + lbuf[(log->v1.start + log->v1.size) &LOGBUFF_MASK ] = *p;if (log->v1.size <LOGBUFF_LEN ) log->v1.size++;
include/configs/lwmon5.h +2 -0
@@ -244,6 +244,8 @@#define CFG_POST_CACHE_ADDR 0x7fff0000/* free virtual address */ #define CONFIG_LOGBUFFER +#define CONFIG_ALT_LH_ADDR (CFG_PERIPHERAL_BASE + GPT0_COMP1) +#define CONFIG_ALT_LB_ADDR (CFG_OCM_BASE)#define CFG_CONSOLE_IS_IN_ENV /* Otherwise it catches logbuffer as output */ /*-----------------------------------------------------------------------
include/ppc440.h +2 -0
@@ -1434,6 +1434,8 @@#define GPT0_COMP5 0x00000094#define GPT0_COMP4 0x00000090#define GPT0_COMP3 0x0000008C +#define GPT0_COMP2 0x00000088 +#define GPT0_COMP1 0x00000084#if defined(CONFIG_440EPX ) || defined(CONFIG_440GRX )#define SDR0_USB2D0CR 0x0320
lib_ppc/board.c +4 -0
@@ -436,10 +436,12 @@ void board_init_f (ulong bootflag) addr =CFG_SDRAM_BASE +get_effective_memsize ();#ifdef CONFIG_LOGBUFFER +#ifndef CONFIG_ALT_LB_ADDR /* reserve kernel log buffer */ addr -= (LOGBUFF_RESERVE );debug ("Reserving %dk for kernel logbuffer at %08lx\n" ,LOGBUFF_LEN , addr);#endif +#endif #ifdef CONFIG_PRAM /*
@@ -1126,9 +1128,11 @@ void board_init_r (gd_t *id, ulong dest_addr) pram=0 ;#endif #ifdef CONFIG_LOGBUFFER +#ifndef CONFIG_ALT_LB_ADDR /* Also take the logbuffer into account (pram is in kB) */ pram += (LOGBUFF_LEN +LOGBUFF_OVERHEAD )/1024 ;#endif +#endif sprintf ((char *)memsz,"%ldk" , (bd->bi_memsize /1024 ) - pram);setenv ("mem" , (char *)memsz); }
Signature · 1 line
1.5.4.2
PATCH 1/1 Fix backlight in the lwmon5 POST.
From: Yuri Tikhonov <[email protected]>
Backlight was switcehd on even when temperature was too low.
Signed-off-by Dmitry Rakhchev <[email protected]>
Signed-off-by Yuri Tikhonov <[email protected]>
--- board/lwmon5/lwmon5.c | 24 +++++++++++++++++++++--- post/board/lwmon5/fpga.c | 10 ---------- post/board/lwmon5/sysmon.c | 33 ++++++++------------------------- 3 files changed, 29 insertions(+), 38 deletions(-)
board/lwmon5/lwmon5.c +21 -3
@@ -567,11 +567,13 @@ unsigned int board_video_init (void)return CFG_LIME_BASE_0 ; } -void board_backlight_switch (int flag) +#define DEFAULT_BRIGHTNESS 0x64 + +static void board_backlight_brightness (int brightness) { -if (flag) { +if (brightness >0 ) {/* pwm duty, lamp on */ -out_be32 ((void *)(CFG_FPGA_BASE_0 +0x00000024 ),0x64 ); +out_be32 ((void *)(CFG_FPGA_BASE_0 +0x00000024 ), brightness);out_be32 ((void *)(CFG_FPGA_BASE_0 +0x00000020 ),0x701 ); }else {/* lamp off */
@@ -580,6 +582,22 @@ void board_backlight_switch (int flag) } } +void board_backlight_switch (int flag) +{ +char * param; +int rc; + +if (flag) { + param =getenv ("brightness" ); + rc = param ?simple_strtol (param,NULL ,10 ) :-1 ; +if (rc <0 ) + rc =DEFAULT_BRIGHTNESS ; + }else { + rc =0 ; + } +board_backlight_brightness (rc); +} +#if defined(CONFIG_CONSOLE_EXTRA_INFO )/* * Return text to be printed besides the logo.
post/board/lwmon5/fpga.c +0 -10
@@ -41,16 +41,6 @@ DECLARE_GLOBAL_DATA_PTR;#define FPGA_RAM_END 0xC4203FFF#define FPGA_STAT 0xC400000C -#define FPGA_PWM_CTRL_REG 0xC4000020 -#define FPGA_PWM_TV_REG 0xC4000024 - -/* Turn on backlight, set brightness */ -void fpga_backlight_enable (int pwm) -{ -out_be16 ((void *)FPGA_PWM_CTRL_REG ,0x0701 ); -out_be16 ((void *)FPGA_PWM_TV_REG , pwm); -} -#if CONFIG_POST &CFG_POST_BSPEC3 static int one_scratch_test (uint value)
post/board/lwmon5/sysmon.c +8 -25
@@ -49,18 +49,16 @@#include <watchdog.h> #include <i2c.h> +#if defined(CONFIG_VIDEO ) +#include <mb862xx.h> +#endif +#if CONFIG_POST &CFG_POST_SYSMON DECLARE_GLOBAL_DATA_PTR ; -#define DEFAULT_BRIGHTNESS 50 -/* from dspic.c */ extern int dspic_read (ushort reg); -/* from fpga.c */ -extern void fpga_backlight_enable (int v); - -static int sysmon_temp_invalid;#define RELOC (x) if (x != NULL) x = (void *) ((ulong) (x) + gd->reloc_off)
@@ -70,7 +68,6 @@ typedef struct sysmon_table_s sysmon_table_t;static void sysmon_dspic_init (sysmon_t * this);static int sysmon_dspic_read (sysmon_t * this,uint addr);static void sysmon_backlight_disable (sysmon_table_t * this); -static void sysmon_backlight_enable (sysmon_table_t * this);struct sysmon_s {
@@ -120,7 +117,7 @@ static sysmon_table_t sysmon_table[] = 100, 1000, -0x8000, 0x7FFF, 0xFFFF, 0x8000+4750, 0x8000+5250, 0, 0x8000+4750, 0x8000+5250, 0, 0x12CA}, - {"+ 5 V standby" ,"V" , &sysmon_dspic,NULL , sysmon_backlight_enable, + {"+ 5 V standby" ,"V" , &sysmon_dspic,NULL ,NULL ,100 ,1000 ,-0x8000 ,0x7FFF ,0xFFFF ,0x8000 +4750 ,0x8000 +5250 ,0 , 0x8000+4750, 0x8000+5250, 0, 0x12C6}, };
@@ -205,23 +202,9 @@ static int sysmon_dspic_read (sysmon_t * this, uint addr)static void sysmon_backlight_disable (sysmon_table_t * this) { -if (!this->val_valid_alt) - sysmon_temp_invalid =1 ; -} - -static void sysmon_backlight_enable (sysmon_table_t * this) -{ -char * param; -int rc; - -if (!sysmon_temp_invalid) { - param =getenv ("brightness" ); - rc = param ?simple_strtol (param,NULL ,10 ) :-1 ; -if (rc >=0 ) -fpga_backlight_enable (rc); -else -fpga_backlight_enable (DEFAULT_BRIGHTNESS ); - } +#if defined(CONFIG_VIDEO ) +board_backlight_switch (this->val_valid_alt); +#endif }int sysmon_post_test (int flags)
Signature · 1 line
1.5.4.2
PATCH 1/1 lwmon5: Fix register test logic to match the specific GDC h/w.
From: Yuri Tikhonov <[email protected]>
Signed-off-by Dmitry Rakhchev <[email protected]>
Signed-off-by Yuri Tikhonov <[email protected]>
--- post/board/lwmon5/gdc.c | 18 ++++++++++++------ 1 files changed, 12 insertions(+), 6 deletions(-)
post/board/lwmon5/gdc.c +12 -6
@@ -35,7 +35,7 @@DECLARE_GLOBAL_DATA_PTR ; -#define GDC_SCRATCH_REG 0xC1FF8008 +#define GDC_SCRATCH_REG 0xC1FF8044#define GDC_VERSION_REG 0xC1FF8084#define GDC_RAM_START 0xC0000000#define GDC_RAM_END 0xC2000000
@@ -44,7 +44,7 @@ DECLARE_GLOBAL_DATA_PTR;static int gdc_test_reg_one (uint value) { -int ret =0 ; +int ret;uint read_value;/* write test pattern */
@@ -56,10 +56,9 @@ static int gdc_test_reg_one(uint value)if (read_value != value) {post_log ("GDC SCRATCH test failed write %08X, read %08X\n" , value, read_value); - ret =1 ; } -return ret; +return (read_value != value); }/* Verify GDC, get memory size */
@@ -71,9 +70,16 @@ int gdc_post_test(int flags)post_log ("\n" ); old_value =in_be32 ((void *)GDC_SCRATCH_REG ); -if (gdc_test_reg_one (0x55555555 )) +/* +* GPIOC2 register behaviour: the LIME graphics processor has a +* maximum of 5 GPIO ports that can be used in this hardware +* configuration. Thus only the bits for these 5 GPIOs can be +* activated in the GPIOC2 register. All other bits will always be +* read as zero. +*/ +if (gdc_test_reg_one (0x00150015 )) ret =1 ; -if (gdc_test_reg_one (0xAAAAAAAA )) +if (gdc_test_reg_one (0x000A000A )) ret =1 ;out_be32 ((void *)GDC_SCRATCH_REG , old_value);
Signature · 1 line
1.5.4.2
PATCH 1/1 POST: preparations for moving CONFIG_POST to Makefiles
From: Yuri Tikhonov <[email protected]>
Remove CONFIG_POST ifdefs from the post/ source files.
Signed-off-by Yuri Tikhonov <[email protected]>
Signed-off-by Wolfgang Denk <[email protected]>
--- post/board/lwmon/sysmon.c | 3 --- post/board/lwmon5/dsp.c | 5 ----- post/board/lwmon5/dspic.c | 4 ---- post/board/lwmon5/fpga.c | 4 ---- post/board/lwmon5/gdc.c | 4 ---- post/board/lwmon5/sysmon.c | 3 --- post/board/lwmon5/watchdog.c | 4 ---- post/board/netta/codec.c | 3 --- post/board/netta/dsp.c | 3 --- post/cpu/mpc8xx/cache.c | 3 --- post/cpu/mpc8xx/cache_8xx.S | 2 -- post/cpu/mpc8xx/ether.c | 4 ---- post/cpu/mpc8xx/spr.c | 3 --- post/cpu/mpc8xx/uart.c | 4 ---- post/cpu/mpc8xx/usb.c | 4 ---- post/cpu/mpc8xx/watchdog.c | 3 --- post/cpu/ppc4xx/cache.c | 3 --- post/cpu/ppc4xx/cache_4xx.S | 3 --- post/cpu/ppc4xx/denali_ecc.c | 4 ++-- post/cpu/ppc4xx/ether.c | 3 --- post/cpu/ppc4xx/fpu.c | 2 -- post/cpu/ppc4xx/spr.c | 3 --- post/cpu/ppc4xx/uart.c | 3 --- post/cpu/ppc4xx/watchdog.c | 3 --- post/drivers/i2c.c | 3 --- post/drivers/memory.c | 3 --- post/drivers/rtc.c | 3 --- post/lib_ppc/andi.c | 3 --- post/lib_ppc/asm.S | 3 --- post/lib_ppc/b.c | 3 --- post/lib_ppc/cmp.c | 3 --- post/lib_ppc/cmpi.c | 3 --- post/lib_ppc/complex.c | 3 --- post/lib_ppc/cpu.c | 3 --- post/lib_ppc/cr.c | 3 --- post/lib_ppc/fpu/20001122-1.c | 3 --- post/lib_ppc/fpu/20010114-2.c | 3 --- post/lib_ppc/fpu/20010226-1.c | 3 --- post/lib_ppc/fpu/980619-1.c | 3 --- post/lib_ppc/fpu/acc1.c | 3 --- post/lib_ppc/fpu/compare-fp-1.c | 3 --- post/lib_ppc/fpu/fpu.c | 3 --- post/lib_ppc/fpu/mul-subnormal-single-1.c | 3 --- post/lib_ppc/load.c | 3 --- post/lib_ppc/multi.c | 3 --- post/lib_ppc/rlwimi.c | 3 --- post/lib_ppc/rlwinm.c | 3 --- post/lib_ppc/rlwnm.c | 3 --- post/lib_ppc/srawi.c | 3 --- post/lib_ppc/store.c | 3 --- post/lib_ppc/string.c | 3 --- post/lib_ppc/three.c | 3 --- post/lib_ppc/threei.c | 3 --- post/lib_ppc/threex.c | 3 --- post/lib_ppc/two.c | 3 --- post/lib_ppc/twox.c | 3 --- post/post.c | 4 ---- post/tests.c | 4 ---- 58 files changed, 2 insertions(+), 182 deletions(-)
post/board/lwmon/sysmon.c +0 -3
@@ -24,8 +24,6 @@#include <post.h> #include <common.h> -#ifdef CONFIG_POST -/* * SYSMON test *
@@ -328,4 +326,3 @@ int sysmon_post_test (int flags) }#endif /* CONFIG_POST & CFG_POST_SYSMON */ -#endif /* CONFIG_POST */
post/board/lwmon5/dsp.c +0 -5
@@ -24,11 +24,8 @@#include <common.h> -#ifdef CONFIG_POST -#include <post.h> -#if CONFIG_POST &CFG_POST_DSP #include <asm/io.h>
@@ -54,5 +51,3 @@ int dsp_post_test(int flags) }#endif /* CONFIG_POST & CFG_POST_DSP */ -#endif /* CONFIG_POST */ -
post/board/lwmon5/dspic.c +0 -4
@@ -24,8 +24,6 @@#include <common.h> -#ifdef CONFIG_POST -/* There are two tests for dsPIC currently implemented: * 1. dsPIC ready test. Done in board_early_init_f(). Only result verified here. * 2. dsPIC POST result test. This test gets dsPIC POST codes and version.
@@ -105,5 +103,3 @@ int dspic_post_test(int flags) }#endif /* CONFIG_POST & CFG_POST_BSPEC2 */ -#endif /* CONFIG_POST */ -
post/board/lwmon5/fpga.c +0 -4
@@ -23,8 +23,6 @@*/ #include <common.h> -#ifdef CONFIG_POST -/* This test performs testing of FPGA SCRATCH register, * gets FPGA version and run get_ram_size() on FPGA memory */
@@ -94,5 +92,3 @@ int fpga_post_test(int flags) }#endif /* CONFIG_POST & CFG_POST_BSPEC3 */ -#endif /* CONFIG_POST */ -
post/board/lwmon5/gdc.c +0 -4
@@ -23,8 +23,6 @@*/ #include <common.h> -#ifdef CONFIG_POST -/* This test attempts to verify board GDC. A scratch register tested, then * simple memory test (get_ram_size()) run over GDC memory. */
@@ -96,5 +94,3 @@ int gdc_post_test(int flags) return ret; }#endif /* CONFIG_POST & CFG_POST_BSPEC4 */ -#endif /* CONFIG_POST */ -
post/board/lwmon5/sysmon.c +0 -3
@@ -25,8 +25,6 @@#include <post.h> #include <common.h> -#ifdef CONFIG_POST -/* * SYSMON test *
@@ -245,4 +243,3 @@ int sysmon_post_test (int flags) }#endif /* CONFIG_POST & CFG_POST_SYSMON */ -#endif /* CONFIG_POST */
post/board/lwmon5/watchdog.c +0 -4
@@ -29,8 +29,6 @@* trigger watchdog reset. */ -#ifdef CONFIG_POST -#include <post.h> #if CONFIG_POST &CFG_POST_WATCHDOG
@@ -128,5 +126,3 @@ int lwmon5_watchdog_post_test(int flags)#endif /* CONFIG_POST & CFG_POST_WATCHDOG */ -#endif /* CONFIG_POST */ -
post/board/netta/codec.c +0 -3
@@ -31,8 +31,6 @@* in the board specific function. */ -#ifdef CONFIG_POST -#include <post.h> #if CONFIG_POST &CFG_POST_CODEC
@@ -45,4 +43,3 @@ int codec_post_test (int flags) }#endif /* CONFIG_POST & CFG_POST_CODEC */ -#endif /* CONFIG_POST */
post/board/netta/dsp.c +0 -3
@@ -31,8 +31,6 @@* in the board specific function. */ -#ifdef CONFIG_POST -#include <post.h> #if CONFIG_POST &CFG_POST_DSP
@@ -45,4 +43,3 @@ int dsp_post_test (int flags) }#endif /* CONFIG_POST & CFG_POST_DSP */ -#endif /* CONFIG_POST */
post/cpu/mpc8xx/cache.c +0 -3
@@ -29,8 +29,6 @@* several test scenarios. */ -#ifdef CONFIG_POST -#include <post.h> #include <watchdog.h>
@@ -78,4 +76,3 @@ int cache_post_test (int flags) }#endif /* CONFIG_POST & CFG_POST_CACHE */ -#endif /* CONFIG_POST */
post/cpu/mpc8xx/cache_8xx.S +0 -2
@@ -22,7 +22,6 @@ #include <config.h> -#ifdef CONFIG_POST #if defined(CONFIG_MPC823) || \ defined(CONFIG_MPC850) || \ defined(CONFIG_MPC855) || \
@@ -492,4 +491,3 @@ cache_post_test6_data: #endif /* CONFIG_MPC823 || MPC850 || MPC855 || MPC860 */ #endif /* CONFIG_POST & CFG_POST_CACHE */ -#endif /* CONFIG_POST */
post/cpu/mpc8xx/ether.c +0 -4
@@ -35,8 +35,6 @@* TEST_NUM - number of tests */ -#ifdef CONFIG_POST -#include <post.h> #if CONFIG_POST &CFG_POST_ETHER #if defined(CONFIG_8xx)
@@ -627,5 +625,3 @@ int ether_post_test (int flags) }#endif /* CONFIG_POST & CFG_POST_ETHER */ - -#endif /* CONFIG_POST */
post/cpu/mpc8xx/spr.c +0 -3
@@ -33,8 +33,6 @@* corresponding table value. */ -#ifdef CONFIG_POST -#include <post.h> #if CONFIG_POST &CFG_POST_SPR
@@ -149,4 +147,3 @@ int spr_post_test (int flags) return ret; }#endif /* CONFIG_POST & CFG_POST_SPR */ -#endif /* CONFIG_POST */
post/cpu/mpc8xx/uart.c +0 -4
@@ -36,8 +36,6 @@* TEST_NUM - number of tests */ -#ifdef CONFIG_POST -#include <post.h> #if CONFIG_POST &CFG_POST_UART #if defined(CONFIG_8xx)
@@ -556,5 +554,3 @@ int uart_post_test (int flags) }#endif /* CONFIG_POST & CFG_POST_UART */ - -#endif /* CONFIG_POST */
post/cpu/mpc8xx/usb.c +0 -4
@@ -34,8 +34,6 @@* Initialization Example. */ -#ifdef CONFIG_POST -#include <post.h> #if CONFIG_POST &CFG_POST_USB
@@ -265,5 +263,3 @@ int usb_post_test (int flags) }#endif /* CONFIG_POST & CFG_POST_USB */ - -#endif /* CONFIG_POST */
post/cpu/mpc8xx/watchdog.c +0 -3
@@ -33,8 +33,6 @@* reboots, on the second iteration the test routine reports a success. */ -#ifdef CONFIG_POST -#include <post.h> #include <watchdog.h>
@@ -75,4 +73,3 @@ int watchdog_post_test (int flags) }#endif /* CONFIG_POST & CFG_POST_WATCHDOG */ -#endif /* CONFIG_POST */
post/cpu/ppc4xx/cache.c +0 -3
@@ -31,8 +31,6 @@* several test scenarios. */ -#ifdef CONFIG_POST -#include <post.h> #if CONFIG_POST &CFG_POST_CACHE
@@ -122,4 +120,3 @@ int cache_post_test (int flags) }#endif /* CONFIG_POST & CFG_POST_CACHE */ -#endif /* CONFIG_POST */
post/cpu/ppc4xx/cache_4xx.S +0 -3
@@ -25,8 +25,6 @@ #include <config.h> -#ifdef CONFIG_POST - #include <post.h> #include <ppc_asm.tmpl> #include <ppc_defs.h>
@@ -489,4 +487,3 @@ cache_post_test_inst: blr #endif /* CONFIG_POST & CFG_POST_CACHE */ -#endif /* CONFIG_POST */
post/cpu/ppc4xx/denali_ecc.c +2 -2
@@ -31,7 +31,7 @@#include <common.h> #include <watchdog.h> -#if defined(CONFIG_POST ) && (defined(CONFIG_440EPX ) || defined(CONFIG_440GRX )) +#if defined(CONFIG_440EPX ) || defined(CONFIG_440GRX )#include <post.h>
@@ -268,4 +268,4 @@ int ecc_post_test(int flags)return ret; }#endif /* CONFIG_POST & CFG_POST_ECC */ -#endif /* defined(CONFIG_POST) && ... */ +#endif /* defined(CONFIG_440EPX) || defined(CONFIG_440GRX) */
post/cpu/ppc4xx/ether.c +0 -3
@@ -37,8 +37,6 @@* TEST_NUM - number of tests */ -#ifdef CONFIG_POST -#include <post.h> #if CONFIG_POST &CFG_POST_ETHER
@@ -430,4 +428,3 @@ out_free: }#endif /* CONFIG_POST & CFG_POST_ETHER */ -#endif /* CONFIG_POST */
post/cpu/ppc4xx/fpu.c +0 -2
@@ -25,7 +25,6 @@#include <config.h> -#ifdef CONFIG_POST #if defined(CONFIG_440EP ) || \ defined(CONFIG_440EPX )
@@ -56,4 +55,3 @@ void fpu_enable(void) }#endif -#endif /* CONFIG_POST */
post/cpu/ppc4xx/spr.c +0 -3
@@ -35,8 +35,6 @@* corresponding table value. */ -#ifdef CONFIG_POST -#include <post.h> #if CONFIG_POST &CFG_POST_SPR
@@ -199,4 +197,3 @@ int spr_post_test (int flags) }#endif /* CONFIG_POST & CFG_POST_SPR */ -#endif /* CONFIG_POST */
post/cpu/ppc4xx/uart.c +0 -3
@@ -32,8 +32,6 @@* characters are transmitted. */ -#ifdef CONFIG_POST -#include <post.h> #if CONFIG_POST &CFG_POST_UART
@@ -389,4 +387,3 @@ int uart_post_test (int flags) }#endif /* CONFIG_POST & CFG_POST_UART */ -#endif /* CONFIG_POST */
post/cpu/ppc4xx/watchdog.c +0 -3
@@ -35,8 +35,6 @@* reboots, on the second iteration the test routine reports a success. */ -#ifdef CONFIG_POST -#include <post.h> #if CONFIG_POST &CFG_POST_WATCHDOG
@@ -68,4 +66,3 @@ int watchdog_post_test (int flags) }#endif /* CONFIG_POST & CFG_POST_WATCHDOG */ -#endif /* CONFIG_POST */
post/drivers/i2c.c +0 -3
@@ -23,8 +23,6 @@#include <common.h> -#ifdef CONFIG_POST -/* * I2C test *
@@ -91,4 +89,3 @@ int i2c_post_test (int flags) }#endif /* CONFIG_POST & CFG_POST_I2C */ -#endif /* CONFIG_POST */
post/drivers/memory.c +0 -3
@@ -150,8 +150,6 @@* the whole RAM. */ -#ifdef CONFIG_POST -#include <post.h> #include <watchdog.h>
@@ -483,4 +481,3 @@ int memory_post_test (int flags) }#endif /* CONFIG_POST & CFG_POST_MEMORY */ -#endif /* CONFIG_POST */
post/drivers/rtc.c +0 -3
@@ -38,8 +38,6 @@* nonleap-years. */ -#ifdef CONFIG_POST -#include <post.h> #include <rtc.h>
@@ -180,4 +178,3 @@ int rtc_post_test (int flags) }#endif /* CONFIG_POST & CFG_POST_RTC */ -#endif /* CONFIG_POST */
post/lib_ppc/andi.c +0 -3
@@ -32,8 +32,6 @@* different sets of operand registers and result registers. */ -#ifdef CONFIG_POST -#include <post.h> #include "cpu_asm.h"
@@ -120,4 +118,3 @@ int cpu_post_test_andi (void) }#endif -#endif
post/lib_ppc/asm.S +0 -3
@@ -22,8 +22,6 @@ #include <config.h> -#ifdef CONFIG_POST - #include <post.h> #include <ppc_asm.tmpl> #include <ppc_defs.h>
@@ -358,4 +356,3 @@ cpu_post_complex_2_loop: blr #endif -#endif
post/lib_ppc/b.c +0 -3
@@ -37,8 +37,6 @@* linked in U-Boot at build time. */ -#ifdef CONFIG_POST -#include <post.h> #include "cpu_asm.h"
@@ -194,4 +192,3 @@ int cpu_post_test_b (void) }#endif -#endif
post/lib_ppc/cmp.c +0 -3
@@ -36,8 +36,6 @@* the result in and the expected result. */ -#ifdef CONFIG_POST -#include <post.h> #include "cpu_asm.h"
@@ -130,4 +128,3 @@ int cpu_post_test_cmp (void) }#endif -#endif
post/lib_ppc/cmpi.c +0 -3
@@ -36,8 +36,6 @@* the result in and the expected result. */ -#ifdef CONFIG_POST -#include <post.h> #include "cpu_asm.h"
@@ -130,4 +128,3 @@ int cpu_post_test_cmpi (void) }#endif -#endif
post/lib_ppc/complex.c +0 -3
@@ -31,8 +31,6 @@* calculations, but probably under different timing conditions, etc. */ -#ifdef CONFIG_POST -#include <post.h> #include "cpu_asm.h"
@@ -123,4 +121,3 @@ int cpu_post_test_complex (void) }#endif -#endif
post/lib_ppc/cpu.c +0 -3
@@ -32,8 +32,6 @@* For more details refer to post/cpu/ *.c files. */ -#ifdef CONFIG_POST -#include <watchdog.h> #include <post.h> #include <asm/mmu.h>
@@ -147,4 +145,3 @@ int cpu_post_test (int flags) }#endif /* CONFIG_POST & CFG_POST_CPU */ -#endif /* CONFIG_POST */
post/lib_ppc/cr.c +0 -3
@@ -46,8 +46,6 @@* expected one. */ -#ifdef CONFIG_POST -#include <post.h> #include "cpu_asm.h"
@@ -353,4 +351,3 @@ int cpu_post_test_cr (void) }#endif -#endif
post/lib_ppc/fpu/20001122-1.c +0 -3
@@ -26,8 +26,6 @@#include <common.h> -#ifdef CONFIG_POST -#include <post.h> #if CONFIG_POST &CFG_POST_FPU
@@ -59,4 +57,3 @@ int fpu_post_test_math1 (void) }#endif /* CONFIG_POST & CFG_POST_FPU */ -#endif /* CONFIG_POST */
post/lib_ppc/fpu/20010114-2.c +0 -3
@@ -26,8 +26,6 @@#include <common.h> -#ifdef CONFIG_POST -#include <post.h> #if CONFIG_POST &CFG_POST_FPU
@@ -63,4 +61,3 @@ int fpu_post_test_math2 (void) }#endif /* CONFIG_POST & CFG_POST_FPU */ -#endif /* CONFIG_POST */
post/lib_ppc/fpu/20010226-1.c +0 -3
@@ -26,8 +26,6 @@#include <common.h> -#ifdef CONFIG_POST -#include <post.h> #if CONFIG_POST &CFG_POST_FPU
@@ -51,4 +49,3 @@ int fpu_post_test_math3 (void) }#endif /* CONFIG_POST & CFG_POST_FPU */ -#endif /* CONFIG_POST */
post/lib_ppc/fpu/980619-1.c +0 -3
@@ -26,8 +26,6 @@#include <common.h> -#ifdef CONFIG_POST -#include <post.h> #if CONFIG_POST &CFG_POST_FPU
@@ -57,4 +55,3 @@ int fpu_post_test_math4 (void) }#endif /* CONFIG_POST & CFG_POST_FPU */ -#endif /* CONFIG_POST */
post/lib_ppc/fpu/acc1.c +0 -3
@@ -26,8 +26,6 @@#include <common.h> -#ifdef CONFIG_POST -#include <post.h> #if CONFIG_POST &CFG_POST_FPU
@@ -54,4 +52,3 @@ int fpu_post_test_math5 (void) }#endif /* CONFIG_POST & CFG_POST_FPU */ -#endif /* CONFIG_POST */
post/lib_ppc/fpu/compare-fp-1.c +0 -3
@@ -28,8 +28,6 @@#include <common.h> -#ifdef CONFIG_POST -#include <post.h> #if CONFIG_POST &CFG_POST_FPU
@@ -222,4 +220,3 @@ int fpu_post_test_math6 (void) }#endif /* CONFIG_POST & CFG_POST_FPU */ -#endif /* CONFIG_POST */
post/lib_ppc/fpu/fpu.c +0 -3
@@ -34,8 +34,6 @@* For more details refer to post/cpu/ *.c files. */ -#ifdef CONFIG_POST -#include <post.h> #if CONFIG_POST &CFG_POST_FPU
@@ -89,4 +87,3 @@ int fpu_post_test (int flags) }#endif /* CONFIG_POST & CFG_POST_FPU */ -#endif /* CONFIG_POST */
post/lib_ppc/fpu/mul-subnormal-single-1.c +0 -3
@@ -28,8 +28,6 @@#include <common.h> -#ifdef CONFIG_POST -#include <post.h> #if CONFIG_POST &CFG_POST_FPU
@@ -100,4 +98,3 @@ int fpu_post_test_math7 (void) }#endif /* CONFIG_POST & CFG_POST_FPU */ -#endif /* CONFIG_POST */
post/lib_ppc/load.c +0 -3
@@ -41,8 +41,6 @@* register (it must change for "load with update" instructions). */ -#ifdef CONFIG_POST -#include <post.h> #include "cpu_asm.h"
@@ -252,4 +250,3 @@ int cpu_post_test_load (void) }#endif -#endif
post/lib_ppc/multi.c +0 -3
@@ -33,8 +33,6 @@* of the source and target buffers are then compared. */ -#ifdef CONFIG_POST -#include <post.h> #include "cpu_asm.h"
@@ -78,4 +76,3 @@ int cpu_post_test_multi (void) }#endif -#endif
post/lib_ppc/rlwimi.c +0 -3
@@ -32,8 +32,6 @@* different sets of operand registers and result registers. */ -#ifdef CONFIG_POST -#include <post.h> #include "cpu_asm.h"
@@ -159,4 +157,3 @@ int cpu_post_test_rlwimi (void) }#endif -#endif
post/lib_ppc/rlwinm.c +0 -3
@@ -32,8 +32,6 @@* different sets of operand registers and result registers. */ -#ifdef CONFIG_POST -#include <post.h> #include "cpu_asm.h"
@@ -152,4 +150,3 @@ int cpu_post_test_rlwinm (void) }#endif -#endif
post/lib_ppc/rlwnm.c +0 -3
@@ -32,8 +32,6 @@* different sets of operand registers and result registers. */ -#ifdef CONFIG_POST -#include <post.h> #include "cpu_asm.h"
@@ -162,4 +160,3 @@ int cpu_post_test_rlwnm (void) }#endif -#endif
post/lib_ppc/srawi.c +0 -3
@@ -32,8 +32,6 @@* different sets of operand registers and result registers. */ -#ifdef CONFIG_POST -#include <post.h> #include "cpu_asm.h"
@@ -153,4 +151,3 @@ int cpu_post_test_srawi (void) }#endif -#endif
post/lib_ppc/store.c +0 -3
@@ -41,8 +41,6 @@* with update" instructions). */ -#ifdef CONFIG_POST -#include <post.h> #include "cpu_asm.h"
@@ -232,4 +230,3 @@ int cpu_post_test_store (void) }#endif -#endif
post/lib_ppc/string.c +0 -3
@@ -33,8 +33,6 @@* of the source and target buffers are then compared. */ -#ifdef CONFIG_POST -#include <post.h> #include "cpu_asm.h"
@@ -103,4 +101,3 @@ int cpu_post_test_string (void) }#endif -#endif
post/lib_ppc/three.c +0 -3
@@ -35,8 +35,6 @@* different sets of operand registers and result registers. */ -#ifdef CONFIG_POST -#include <post.h> #include "cpu_asm.h"
@@ -256,4 +254,3 @@ int cpu_post_test_three (void) }#endif -#endif
post/lib_ppc/threei.c +0 -3
@@ -34,8 +34,6 @@* different sets of operand registers and result registers. */ -#ifdef CONFIG_POST -#include <post.h> #include "cpu_asm.h"
@@ -134,4 +132,3 @@ int cpu_post_test_threei (void) }#endif -#endif
post/lib_ppc/threex.c +0 -3
@@ -35,8 +35,6 @@* different sets of operand registers and result registers. */ -#ifdef CONFIG_POST -#include <post.h> #include "cpu_asm.h"
@@ -226,4 +224,3 @@ int cpu_post_test_threex (void) }#endif -#endif
post/lib_ppc/two.c +0 -3
@@ -35,8 +35,6 @@* different sets of operand registers and result registers. */ -#ifdef CONFIG_POST -#include <post.h> #include "cpu_asm.h"
@@ -173,4 +171,3 @@ int cpu_post_test_two (void) }#endif -#endif
post/lib_ppc/twox.c +0 -3
@@ -35,8 +35,6 @@* different sets of operand registers and result registers. */ -#ifdef CONFIG_POST -#include <post.h> #include "cpu_asm.h"
@@ -173,4 +171,3 @@ int cpu_post_test_twox (void) }#endif -#endif
post/post.c +0 -4
@@ -30,8 +30,6 @@#include <logbuff.h> #endif -#ifdef CONFIG_POST -DECLARE_GLOBAL_DATA_PTR ;#define POST_MAX_NUMBER 32
@@ -442,5 +440,3 @@ unsigned long post_time_ms (unsigned long base)return 0 ;/* Not implemented yet */ #endif } - -#endif /* CONFIG_POST */
post/tests.c +0 -4
@@ -27,8 +27,6 @@#include <common.h> -#ifdef CONFIG_POST -#include <post.h> extern int cache_post_test (int flags);
@@ -278,5 +276,3 @@ struct post_test post_list[] = };unsigned int post_list_size =sizeof (post_list) /sizeof (struct post_test ); - -#endif /* CONFIG_POST */
Signature · 1 line
1.5.4.2
PATCH 1/1 POST: move CONFIG_POST to Makefiles
From: Yuri Tikhonov <[email protected]>
Introduce the new logical option CONFIG_HAS_POST which is set when the platform has CONFIG_POST set. Use CONFIG_HAS_POST in the post/ Makefiles to determine should the POST libs be compiled for the selected target platform, or not.
To avoid breaking u-boot linking process, the empty post/libpost.a file is created for platforms which do not have POSTs.
Signed-off-by Yuri Tikhonov <[email protected]>
Signed-off-by Wolfgang Denk <[email protected]>
--- Makefile | 10 +-------- include/common.h | 11 ++++++++++ post/Makefile | 47 ++++++++++++++++++++++++++++++++++++++++--- post/board/lwmon5/Makefile | 3 +- post/cpu/ppc4xx/Makefile | 5 ++- post/drivers/Makefile | 6 +--- post/lib_ppc/Makefile | 11 ++++----- post/lib_ppc/fpu/Makefile | 6 ++-- post/rules.mk | 2 + 9 files changed, 72 insertions(+), 29 deletions(-)
Makefile +1 -9
@@ -233,18 +233,10 @@ LIBS += drivers/rtc/librtc.a LIBS += drivers/serial/libserial.a LIBS += drivers/usb/libusb.a LIBS += drivers/video/libvideo.a -LIBS += post/libpost.a post/drivers/libpostdrivers.a -LIBS += $(shell if [ -d post/lib_$(ARCH) ]; then echo \ - "post/lib_$(ARCH)/libpost$(ARCH).a"; fi) -LIBS += $(shell if [ -d post/lib_$(ARCH)/fpu ]; then echo \ - "post/lib_$(ARCH)/fpu/libpost$(ARCH)fpu.a"; fi) -LIBS += $(shell if [ -d post/cpu/$(CPU) ]; then echo \ - "post/cpu/$(CPU)/libpost$(CPU).a"; fi) -LIBS += $(shell if [ -d post/board/$(BOARDDIR) ]; then echo \ - "post/board/$(BOARDDIR)/libpost$(BOARD).a"; fi) LIBS += common/libcommon.a LIBS += libfdt/libfdt.a LIBS += api/libapi.a +LIBS += post/libpost.a LIBS := $(addprefix $(obj),$(LIBS)) .PHONY : $(LIBS) $(VERSION_FILE)
include/common.h +11 -0
@@ -672,4 +672,15 @@ void inline show_boot_progress (int val);#define ARRAY_SIZE (x) (sizeof(x) / sizeof((x)[0])) +/* Multicore arch functions */ +#ifdef CONFIG_MP +int cpu_status (int nr); +int cpu_reset (int nr); +int cpu_release (int nr,int argc,char *argv[]); +#endif + +#ifdef CONFIG_POST +#define CONFIG_HAS_POST +#endif +#endif /* __COMMON_H_ */
post/Makefile +43 -4
54 lines not on this page · raw message
post/board/lwmon5/Makefile +2 -1
@@ -20,9 +20,10 @@ # along with this program; if not, write to the Free Software # Foundation, Inc., 59 Temple Place, Suite 330, Boston, # MA 02111-1307 USA +include $(TOPDIR)/include/autoconf.mk LIB = libpostlwmon5.a -COBJS = sysmon.o watchdog.o dspic.o fpga.o dsp.o gdc.o +COBJS-$(CONFIG_HAS_POST) += sysmon.o watchdog.o dspic.o fpga.o dsp.o gdc.o include $(TOPDIR)/post/rules.mk
post/cpu/ppc4xx/Makefile +3 -2
@@ -20,10 +20,11 @@ # Foundation, Inc., 59 Temple Place, Suite 330, Boston, # MA 02111-1307 USA # +include $(TOPDIR)/include/autoconf.mk LIB = libpostppc4xx.a -AOBJS = cache_4xx.o -COBJS = cache.o denali_ecc.o ether.o fpu.o spr.o uart.o watchdog.o +AOBJS-$(CONFIG_HAS_POST) += cache_4xx.o +COBJS-$(CONFIG_HAS_POST) += cache.o denali_ecc.o ether.o fpu.o spr.o uart.o watchdog.o include $(TOPDIR)/post/rules.mk
post/drivers/Makefile +2 -4
@@ -20,12 +20,10 @@ # Foundation, Inc., 59 Temple Place, Suite 330, Boston, # MA 02111-1307 USA # - - -SUBDIRS = +include $(TOPDIR)/config.mk LIB = libpostdrivers.a -COBJS = i2c.o memory.o rtc.o +COBJS-$(CONFIG_HAS_POST) += i2c.o memory.o rtc.o include $(TOPDIR)/post/rules.mk
post/lib_ppc/Makefile +5 -6
@@ -20,14 +20,13 @@ # Foundation, Inc., 59 Temple Place, Suite 330, Boston, # MA 02111-1307 USA # - -SUBDIRS = fpu +include $(TOPDIR)/config.mk LIB = libpostppc.a -AOBJS = asm.o -COBJS = cpu.o cmp.o cmpi.o two.o twox.o three.o threex.o -COBJS += threei.o andi.o srawi.o rlwnm.o rlwinm.o rlwimi.o -COBJS += store.o load.o cr.o b.o multi.o string.o complex.o +AOBJS-$(CONFIG_HAS_POST) += asm.o +COBJS-$(CONFIG_HAS_POST) += cpu.o cmp.o cmpi.o two.o twox.o three.o threex.o +COBJS-$(CONFIG_HAS_POST) += threei.o andi.o srawi.o rlwnm.o rlwinm.o rlwimi.o +COBJS-$(CONFIG_HAS_POST) += store.o load.o cr.o b.o multi.o string.o complex.o include $(TOPDIR)/post/rules.mk
post/lib_ppc/fpu/Makefile +3 -3
@@ -20,12 +20,12 @@ # Foundation, Inc., 59 Temple Place, Suite 330, Boston, # MA 02111-1307 USA # - +include $(TOPDIR)/config.mk LIB = libpostppcfpu.a -COBJS += fpu.o 20001122-1.o 20010114-2.o 20010226-1.o 980619-1.o -COBJS += acc1.o compare-fp-1.o mul-subnormal-single-1.o +COBJS-$(CONFIG_HAS_POST) += fpu.o 20001122-1.o 20010114-2.o 20010226-1.o 980619-1.o +COBJS-$(CONFIG_HAS_POST) += acc1.o compare-fp-1.o mul-subnormal-single-1.o include $(TOPDIR)/post/rules.mk
post/rules.mk +2 -0
@@ -23,6 +23,8 @@ include $(TOPDIR)/config.mk +COBJS := $(COBJS-y) +AOBJS := $(AOBJS-y) SRCS := $(AOBJS:.o=.S) $(COBJS:.o=.c) OBJS := $(addprefix $(obj),$(AOBJS) $(COBJS)) LIB := $(obj)$(LIB)
Signature · 1 line
1.5.4.2
PATCH 1/1 lwmon5 watchdog: limit trigger rate
From: Yuri Tikhonov <[email protected]>
Limit the rate of h/w watch-dog triggering on the LWMON5 board by the CONFIG_WD_MAX_RATE value.
Note that an earlier version of this patch which used microseconds instead of ticks dis not work. The problem was that we used usec2ticks() to convert microseconds into ticks. usec2ticks() uses get_tbclk(), which in turn calls get_sys_info(). It turns out that this function does a lot of prolonged operations (like divisions) which take too much time so we do not trigger the watchdog in time, and it resets the system.
Signed-off-by Yuri Tikhonov <[email protected]>
--- board/lwmon5/lwmon5.c | 18 ++++++++++++++++++ include/asm-ppc/global_data.h | 3 +++ include/configs/lwmon5.h | 1 + 3 files changed, 22 insertions(+), 0 deletions(-)
board/lwmon5/lwmon5.c +18 -0
@@ -476,6 +476,24 @@ int is_pci_host(struct pci_controller *hose)void hw_watchdog_reset (void ) {int val; +#if defined(CONFIG_WD_MAX_RATE ) +unsigned long long ct =get_ticks (); + +/* +* Don't allow watch-dog triggering more frequently than +* the predefined value CONFIG_WD_MAX_RATE [ticks]. +*/ +if (ct >= gd->wdt_last) { +if ((ct - gd->wdt_last) <CONFIG_WD_MAX_RATE ) +return ; + }else { +/* Time base counter had been reset */ +if (((unsigned long long )(-1 ) - gd->wdt_last + ct) < +CONFIG_WD_MAX_RATE ) +return ; + } + gd->wdt_last =get_ticks (); +#endif /* * Toggle watchdog output
include/asm-ppc/global_data.h +3 -0
@@ -155,6 +155,9 @@ typedef struct global_data {#if defined(CONFIG_LWMON ) || defined(CONFIG_LWMON5 )unsigned long kbd_status;#endif +#if defined(CONFIG_WD_MAX_RATE ) +unsigned long long wdt_last;/* trace watch-dog triggering rate */ +#endif void **jt;/* jump table */ } gd_t;
include/configs/lwmon5.h +1 -0
@@ -455,6 +455,7 @@#define CONFIG_HW_WATCHDOG 1/* Use external HW-Watchdog */ #define CONFIG_WD_PERIOD 40000/* in usec */ +#define CONFIG_WD_MAX_RATE 66600/* in ticks */ /* * For booting Linux, the board info and command line data
Signature · 1 line
1.5.4.2
PATCH 1/1 Added watchdog triggering calls in the "mtest" test function.
From: Sergei Poselenov <[email protected]>
Signed-off-by Sergei Poselenov <[email protected]>
--- common/cmd_mem.c | 7 +++++++ 1 files changed, 7 insertions(+), 0 deletions(-)
common/cmd_mem.c +7 -0
@@ -35,6 +35,7 @@#ifdef CONFIG_HAS_DATAFLASH #include <dataflash.h> #endif +#include <watchdog.h> #if defined(CONFIG_CMD_MEMORY ) \ || defined(CONFIG_CMD_I2C ) \
@@ -868,6 +869,7 @@ int do_mem_mtest (cmd_tbl_t *cmdtp, int flag, int argc, char *argv[]) } } start[test_offset] = pattern; +WATCHDOG_RESET ();/* * Check for addr bits stuck low or shorted.
@@ -905,6 +907,7 @@ int do_mem_mtest (cmd_tbl_t *cmdtp, int flag, int argc, char *argv[])* Fill memory with a known pattern. */ for (pattern =1 , offset =0 ; offset < num_words; pattern++, offset++) { +WATCHDOG_RESET (); start[offset] = pattern; }
@@ -912,6 +915,7 @@ int do_mem_mtest (cmd_tbl_t *cmdtp, int flag, int argc, char *argv[])* Check each location and invert it for the second pass. */ for (pattern =1 , offset =0 ; offset < num_words; pattern++, offset++) { +WATCHDOG_RESET (); temp = start[offset];if (temp != pattern) { printf ("\nFAILURE (read/write) @ 0x%.8lx:"
@@ -928,6 +932,7 @@ int do_mem_mtest (cmd_tbl_t *cmdtp, int flag, int argc, char *argv[])* Check each location for the inverted pattern and zero it. */ for (pattern =1 , offset =0 ; offset < num_words; pattern++, offset++) { +WATCHDOG_RESET (); anti_pattern = ~pattern; temp = start[offset];if (temp != anti_pattern) {
@@ -954,6 +959,7 @@ int do_mem_mtest (cmd_tbl_t *cmdtp, int flag, int argc, char *argv[]) pattern, "");for (addr=start,val=pattern; addr<end; addr++) { +WATCHDOG_RESET (); *addr = val; val += incr; }
@@ -961,6 +967,7 @@ int do_mem_mtest (cmd_tbl_t *cmdtp, int flag, int argc, char *argv[])puts ("Reading..." );for (addr=start,val=pattern; addr<end; addr++) { +WATCHDOG_RESET (); readback = *addr;if (readback != val) { printf ("\nMem error @ 0x%08X: "
Signature · 1 line
1.5.4.2
PATCH 1/1 lwmon5 watchdog: limit trigger rate
In reply to Wolfgang DenkQuoted 13 lines · Wolfgang Denk
From: Yuri Tikhonov <[email protected]>
Limit the rate of h/w watch-dog triggering on the LWMON5 board by the
CONFIG_WD_MAX_RATEvalue.Note that an earlier version of this patch which used microseconds instead of ticks dis not work. The problem was that we used
usec2ticks()to convert microseconds into ticks.usec2ticks()usesget_tbclk(), which in turn callsget_sys_info(). It turns out that this function does a lot of prolonged operations (like divisions) which take too much time so we do not trigger the watchdog in time, and it resets the system.
Quoted 1 line
Signed-off-by Yuri Tikhonov <[email protected]>
Applied to u-boot-ppc4xx repository. Thanks.
Best regards,
Stefan
=====================================================================
DENX Software Engineering GmbH, MD: Wolfgang Denk & Detlev Zundel
HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany
Phone: +49-8142-66989-0 Fax: +49-8142-66989-80 Email: office at denx.de
=====================================================================
PATCH 1/1 lwmon5: Fix register test logic to match the specific GDC h/w.
In reply to Wolfgang DenkQuoted 4 lines · Wolfgang Denk
From: Yuri Tikhonov <[email protected]>
Signed-off-by Dmitry Rakhchev <[email protected]>Signed-off-by Yuri Tikhonov <[email protected]>
Already included in current U-Boot.
Best regards,
Stefan
=====================================================================
DENX Software Engineering GmbH, MD: Wolfgang Denk & Detlev Zundel
HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany
Phone: +49-8142-66989-0 Fax: +49-8142-66989-80 Email: office at denx.de
=====================================================================
PATCH 1/1 Fix backlight in the lwmon5 POST.
In reply to Wolfgang DenkQuoted 6 lines · Wolfgang Denk
From: Yuri Tikhonov <[email protected]>
Backlight was switcehd on even when temperature was too low.
Signed-off-by Dmitry Rakhchev <[email protected]>Signed-off-by Yuri Tikhonov <[email protected]>
Already included in current U-Boot.
Best regards,
Stefan
=====================================================================
DENX Software Engineering GmbH, MD: Wolfgang Denk & Detlev Zundel
HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany
Phone: +49-8142-66989-0 Fax: +49-8142-66989-80 Email: office at denx.de
=====================================================================
PATCH 1/1 Add support for the lwmon5 board reset via GPIO58.
In reply to Wolfgang DenkQuoted 4 lines · Wolfgang Denk
From: Yuri Tikhonov <[email protected]>
Signed-off-by Dmitry Rakhchev <[email protected]>Signed-off-by Yuri Tikhonov <[email protected]>
Already included in current U-Boot.
Best regards,
Stefan
=====================================================================
DENX Software Engineering GmbH, MD: Wolfgang Denk & Detlev Zundel
HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany
Phone: +49-8142-66989-0 Fax: +49-8142-66989-80 Email: office at denx.de
=====================================================================
PATCH 1/1 Some fixes to dspic, fpga, and gdc post tests for lwmon5.
In reply to Wolfgang DenkQuoted 4 lines · Wolfgang Denk
From: Yuri Tikhonov <[email protected]>
Signed-off-by Dmitry Rakhchev <[email protected]>Signed-off-by Yuri Tikhonov <[email protected]>
Already included in current U-Boot.
Best regards,
Stefan
=====================================================================
DENX Software Engineering GmbH, MD: Wolfgang Denk & Detlev Zundel
HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany
Phone: +49-8142-66989-0 Fax: +49-8142-66989-80 Email: office at denx.de
=====================================================================
PATCH 1/1 The patch adds new POST tests for the Lwmon5 board.
In reply to Wolfgang DenkQuoted 10 lines · Wolfgang Denk
From: Yuri Tikhonov <[email protected]>
* External Watchdog test;
* dsPIC tests;
* FPGA test;
* GDC test;
* Sysmon tests.Signed-off-by Dmitry Rakhchev <[email protected]>Signed-off-by Yuri Tikhonov <[email protected]>
Already included in current U-Boot.
Best regards,
Stefan
=====================================================================
DENX Software Engineering GmbH, MD: Wolfgang Denk & Detlev Zundel
HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany
Phone: +49-8142-66989-0 Fax: +49-8142-66989-80 Email: office at denx.de
=====================================================================