Trouble seeing some wireless networks in latest git
Hey,
There seems to be some kind of regression in wireless drivers that makes it not possible to see some wireless networks.
This can be seen with both b43 and iwl3945 drivers.
Using Kismet wireless scanner these networks were visible under latest git.
All the networks rendered invisible seem to be from channels: 1 (one network visible), 3, 8, 12 and 13. Visible networks are in channels 1, 4, 6, 9 and 11.
Any hints how to debug this further?
--
Priit
Quoted 7 lines · Priit Laes
Hey,
There seems to be some kind of regression in wireless drivers that makes it not possible to see some wireless networks.
This can be seen with both b43 and iwl3945 drivers.
Quoted 7 lines
Using Kismet wireless scanner these networks were visible under latest git.
All the networks rendered invisible seem to be from channels: 1 (one network visible), 3, 8, 12 and 13. Visible networks are in channels 1, 4, 6, 9 and 11.Any hints how to debug this further?
This regression sounds like a perfect place to use git bisection. As it affects b43 and iwl3945, I would suspect some change in mac80211.
Larry
Quoted 14 lines · On Sunday 27 April 2008 17:43:39 Larry Finger wrote:
Quoted 13 lines · Priit Laes
Hey,
There seems to be some kind of regression in wireless drivers that makes it not possible to see some wireless networks.
This can be seen with both b43 and iwl3945 drivers.
Using Kismet wireless scanner these networks were visible under latest git.
All the networks rendered invisible seem to be from channels: 1 (one network visible), 3, 8, 12 and 13. Visible networks are in channels 1, 4, 6, 9 and 11.
Quoted 4 lines
Quoted 1 line
Any hints how to debug this further?
This regression sounds like a perfect place to use git bisection. As it affects b43 and iwl3945, I would suspect some change in mac80211.
Nah, it's a regulatory setting issue.
The default regdomain is US, which only allows chans 1-11. There's some module parameter to switch the regdomain. This is not a regression, but a feature.
Signature · 1 line
Greetings Michael.
=C3=9Chel kenal p=C3=A4eval, P, 2008-04-27 kell 17:48, kirjutas Michael=
Buesch:
Quoted 6 lines
Quoted 1 line
Quoted 1 line
Any hints how to debug this further?
Nah, it's a regulatory setting issue.
The default regdomain is US, which only allows chans 1-11. There's some module parameter to switch the regdomain. This is not a regression, but a feature.
=20
Regdomain setting seems to be OK (and missing for b43):
=EF=BB=BFiwl3945: Tunable channels: 13 802.11bg, 23 802.11a channels
Where can I set the regdomain? I couldn't find any information under Documentation and with modinfo?
Dmesg output for iwl3945 is:
=2E..
iwl3945: Intel(R) PRO/Wireless 3945ABG/BG Network Connection driver for Linux, 1.2.26ks
iwl3945: Copyright(c) 2003-2008 Intel Corporation
ACPI: PCI Interrupt 0000:03:00.0[A] -> GSI 17 (level, low) -> IRQ 17
PCI: Setting latency timer of device 0000:03:00.0 to 64
iwl3945: Detected Intel Wireless WiFi Link 3945ABG
iwl3945: Tunable channels: 13 802.11bg, 23 802.11a channels
phy0: Selected rate control algorithm 'iwl-3945-rs'
=2E..
And b43:
=2E..
b43-pci-bridge 0000:16:00.0: enabling device (0000 -> 0002)
ACPI: PCI Interrupt 0000:16:00.0[A] -> GSI 16 (level, low) -> IRQ 16
PCI: Setting latency timer of device 0000:16:00.0 to 64
ssb: Sonics Silicon Backplane found on PCI device 0000:16:00.0
b43-phy1: Broadcom 4306 WLAN found
phy1: Selected rate control algorithm 'pid'
Broadcom 43xx driver loaded [ Features: PMLR, Firmware-ID: FW13 ]
input: b43-phy1 as /devices/virtual/input/input9
b43-phy1: Loading firmware version 410.2160 (2007-05-26 15:32:10) Registered led device: b43-phy1::tx
Registered led device: b43-phy1::rx
Registered led device: b43-phy1::radio
=2E..
--
To unsubscribe from this list: send the line "unsubscribe linux-wireles= s" in
the body of a message to [email protected]
More majordomo info at http://vger.kernel.org/majordomo-info.html
Quoted 2 lines · On Sun, 27 Apr 2008 20:00:25 +0300 Priit Laes <[email protected]> wrote:
Where can I set the regdomain? I couldn't find any information under Documentation and with modinfo?
In /etc/modprobe.conf or equivalent, add:
options cfg80211 ieee80211_regdom="US" or "JP"
Currently these are the only two regulatory domains available.
Signature · 4 lines
Brian Morrison
"Arguing with an engineer is like wrestling with a pig in the mud;
after a while you realize you are muddy and the pig is enjoying it."Quoted 9 lines · Priit Laes
Ühel kenal päeval, P, 2008-04-27 kell 17:48, kirjutas Michael Buesch:
Quoted 6 lines
Quoted 1 line
Quoted 1 line
Any hints how to debug this further?
Nah, it's a regulatory setting issue.
The default regdomain is US, which only allows chans 1-11. There's some module parameter to switch the regdomain. This is not a regression, but a feature.Regdomain setting seems to be OK (and missing for b43):
iwl3945: Tunable channels: 13 802.11bg, 23 802.11a channels
This should really read "EEPROM tunable channels" instead, cfg80211 will further restrict it.
johannes