Skip to contentSkip to conversation

SB0880 X-Fi Titanium Fatal1ty Pro (with codecgraph)

DISCUSSION Tony "Chainsaw" Vroon 4 participants 10 messages Jul 13, 2008 – Jul 15, 2008

lore
Share & tools
lore
#0 lore raw

Good evening,

Just wanted to share that this card seems to be HD-Audio compatible (by virtue of its UAA compatibility claim);
http://uk.europe.creative.com/products/product.asp?category=1&subcategory=208&product=17791

For a while now, I've been trying to write a skeleton patch_creative.c to hook up some basic playback functions. As this has failed, I will instead post all information I can gather about the card, in the hope that such a basic patch_creative.c can be written that I can then slowly extend.
I was unable to set up proper PCM paths (and thus listen to any audio at all), but did manage to get the card detected with a simple addition to hda_intel.c:
+ /* Creative Labs UAA-compatible */
+ { PCI_DEVICE(0x1102, 0x000b), .driver_data =
AZX_DRIVER_CREATIVE },

A guess at correct mixer controls would be:
HDA_CODEC_VOLUME("PCM Playback Volume", 0x02, 0x0, HDA_OUTPUT), HDA_CODEC_MUTE("PCM Playback Switch", 0x02, 0x0, HDA_OUTPUT), HDA_CODEC_VOLUME("Surround Playback Volume", 0x03, 0x0, HDA_OUTPUT), HDA_CODEC_MUTE("Surround Playback Switch", 0x03, 0x0, HDA_OUTPUT), HDA_CODEC_VOLUME_MONO("Center Playback Volume", 0x04, 1, 0x0, HDA_OUTPUT),
HDA_CODEC_MUTE_MONO("Center Playback Switch", 0x04, 1, 0x0, HDA_OUTPUT), HDA_CODEC_VOLUME_MONO("LFE Playback Volume", 0x04, 2, 0x0, HDA_OUTPUT), HDA_CODEC_MUTE_MONO("LFE Playback Switch", 0x04, 2, 0x0, HDA_OUTPUT), HDA_CODEC_VOLUME("Side Playback Volume", 0x05, 0x0, HDA_OUTPUT), HDA_CODEC_MUTE("Side Playback Switch", 0x05, 0x0, HDA_OUTPUT),

Please find attached the codec details and the resulting codec graph.

It is a PCI-Express card, lspci information follows:
83:00.0 Audio device [0403]: Creative Labs Device [1102:000b] (rev 03)

	Subsystem: Creative Labs Device [1102:0043]
	Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-

Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 505
Region 0: Memory at d0100000 (64-bit, non-prefetchable) [size=64K] Region 2: Memory at d0200000 (64-bit, non-prefetchable) [size=2M] Region 4: Memory at d4000000 (64-bit, non-prefetchable) [size=64M]
Capabilities: [40] Power Management version 3
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA
PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [48] Message Signalled Interrupts: Mask- 64bit+ Queue=0/0
Enable+
Address: 00000000feeff00c Data: 41c9
Capabilities: [58] Express (v2) Endpoint, MSI 00
DevCap: MaxPayload 128 bytes, PhantFunc 0, Latency L0s <64ns, L1 <1us
ExtTag- AttnBtn- AttnInd- PwrInd- RBE+ FLReset-
DevCtl: Report errors: Correctable- Non-Fatal- Fatal- Unsupported-
RlxdOrd+ ExtTag- PhantFunc- AuxPwr- NoSnoop+ MaxPayload 128 bytes, MaxReadReq 512 bytes
DevSta: CorrErr+ UncorrErr- FatalErr- UnsuppReq+ AuxPwr- TransPend-
LnkCap: Port #0, Speed 2.5GT/s, Width x1, ASPM L0s L1, Latency L0
<64ns, L1 <1us
ClockPM- Suprise- LLActRep- BwNot-
LnkCtl: ASPM Disabled; RCB 64 bytes Disabled- Retrain- CommClk-
ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
LnkSta: Speed 2.5GT/s, Width x1, TrErr- Train- SlotClk- DLActive-
BWMgmt- ABWMgmt-
Capabilities: [100] Device Serial Number ff-ff-ff-ff-ff-ff-ff-ff
Capabilities: [300] Advanced Error Reporting <?>
Kernel driver in use: HDA Intel

Regards,
Tony V.

Codec: Generic 1102 SB0880
Address: 1
Vendor Id: 0x1102000d
Subsystem Id: 0x11020043
Revision Id: 0x100000
No Modem Function Group found
Default PCM:

    rates [0x160]: 44100 48000 96000
    bits [0xa]: 16 24
    formats [0x1]: PCM

Default Amp-In caps: ofs=0x67, nsteps=0x73, stepsize=0x01, mute=1 Default Amp-Out caps: ofs=0x67, nsteps=0x67, stepsize=0x01, mute=1
GPIO: io=0, o=0, i=0, unsolicited=0, wake=0
Node 0x02 [Audio Output] wcaps 0x5: Stereo Amp-Out
Amp-Out caps: ofs=0x67, nsteps=0x7f, stepsize=0x01, mute=1 Amp-Out vals: [0x40 0x40]
Converter: stream=0, channel=0
Node 0x03 [Audio Output] wcaps 0x5: Stereo Amp-Out
Amp-Out caps: ofs=0x67, nsteps=0x7f, stepsize=0x01, mute=1 Amp-Out vals: [0x67 0x67]
Converter: stream=0, channel=0
Node 0x04 [Audio Output] wcaps 0x5: Stereo Amp-Out
Amp-Out caps: ofs=0x67, nsteps=0x7f, stepsize=0x01, mute=1 Amp-Out vals: [0x67 0x67]
Converter: stream=0, channel=0
Node 0x05 [Audio Output] wcaps 0x5: Stereo Amp-Out
Amp-Out caps: ofs=0x67, nsteps=0x7f, stepsize=0x01, mute=1 Amp-Out vals: [0x67 0x67]
Converter: stream=0, channel=0
Node 0x06 [Vendor Defined Widget] wcaps 0xf0001d: Stereo Amp-Out
Amp-Out caps: ofs=0x67, nsteps=0x7f, stepsize=0x01, mute=1 Amp-Out vals: [0x67 0x67]
Node 0x07 [Audio Output] wcaps 0x205: Stereo Digital Amp-Out
Amp-Out caps: ofs=0x67, nsteps=0x7f, stepsize=0x01, mute=1 Amp-Out vals: [0x67 0x67]
Converter: stream=0, channel=0
Digital:
Digital category: 0x0
Node 0x08 [Audio Input] wcaps 0x100103: Stereo Amp-In
Amp-In caps: ofs=0x67, nsteps=0x7f, stepsize=0x01, mute=1 Amp-In vals: [0x67 0x67]
Converter: stream=0, channel=0
SDI-Select: 0
Connection: 1

     0x13

Node 0x09 [Audio Input] wcaps 0x10010b: Stereo Amp-In
Amp-In caps: ofs=0x67, nsteps=0x7f, stepsize=0x01, mute=1 Amp-In vals: [0x67 0x67]
Converter: stream=0, channel=0
SDI-Select: 0
Connection: 1

     0x14

Node 0x0a [Audio Input] wcaps 0x10011b: Stereo Amp-In
Amp-In caps: ofs=0x67, nsteps=0x7f, stepsize=0x01, mute=1 Amp-In vals: [0x67 0x67]
Converter: stream=0, channel=0
SDI-Select: 0
PCM:

    rates [0x560]: 44100 48000 96000 192000
    bits [0xa]: 16 24
    formats [0x1]: PCM
  Connection: 1
     0x15

Node 0x0b [Audio Input] wcaps 0x10011b: Stereo Amp-In
Amp-In caps: ofs=0x67, nsteps=0x7f, stepsize=0x01, mute=1 Amp-In vals: [0x67 0x67]
Converter: stream=0, channel=0
SDI-Select: 0
PCM:

    rates [0x560]: 44100 48000 96000 192000
    bits [0xa]: 16 24
    formats [0x1]: PCM
  Connection: 1
     0x16

Node 0x0c [Audio Input] wcaps 0x100303: Stereo Digital Amp-In
Amp-In caps: ofs=0x67, nsteps=0x7f, stepsize=0x01, mute=1 Amp-In vals: [0x67 0x67]
Converter: stream=0, channel=0
SDI-Select: 0
Digital: Copyright Non-Audio Pro GenLevel
Digital category: 0x70
Connection: 1

     0x17

Node 0x0d [Pin Complex] wcaps 0x400189: Stereo
Pincap 0x0814: OUT Detect
Pin Default 0x01014010: [Jack] Line Out at Ext Rear
Conn = 1/8, Color = Green
DefAssociation = 0x1, Sequence = 0x0
Pin-ctls: 0xc0: OUT HP
Unsolicited: tag=00, enabled=0
Connection: 1

     0x02

Node 0x0e [Pin Complex] wcaps 0x400189: Stereo
Pincap 0x0814: OUT Detect
Pin Default 0x01016011: [Jack] Line Out at Ext Rear
Conn = 1/8, Color = Orange
DefAssociation = 0x1, Sequence = 0x1
Pin-ctls: 0xc0: OUT HP
Unsolicited: tag=00, enabled=0
Connection: 1

     0x03

Node 0x0f [Pin Complex] wcaps 0x400189: Stereo
Pincap 0x0814: OUT Detect
Pin Default 0x01011012: [Jack] Line Out at Ext Rear
Conn = 1/8, Color = Black
DefAssociation = 0x1, Sequence = 0x2
Pin-ctls: 0xc0: OUT HP
Unsolicited: tag=00, enabled=0
Connection: 1

     0x04

Node 0x10 [Pin Complex] wcaps 0x400189: Stereo
Pincap 0x0814: OUT Detect
Pin Default 0x01012014: [Jack] Line Out at Ext Rear
Conn = 1/8, Color = Grey
DefAssociation = 0x1, Sequence = 0x4
Pin-ctls: 0xc0: OUT HP
Unsolicited: tag=00, enabled=0
Connection: 1

     0x05

Node 0x11 [Pin Complex] wcaps 0x400189: Stereo
Pincap 0x081c: OUT HP Detect
Pin Default 0x00000000: [Jack] Line Out at Ext N/A
Conn = Unknown, Color = Unknown DefAssociation = 0x0, Sequence = 0x0
Pin-ctls: 0xc0: OUT HP
Unsolicited: tag=00, enabled=0
Connection: 1

     0x02

Node 0x12 [Pin Complex] wcaps 0x400389: Stereo Digital
Pincap 0x0810: OUT
Pin Default 0x01452130: [Jack] SPDIF Out at Ext Rear
Conn = Optical, Color = Grey DefAssociation = 0x3, Sequence = 0x0
Misc = NO_PRESENCE
Pin-ctls: 0xc0: OUT HP
Unsolicited: tag=00, enabled=0
Connection: 1

     0x07

Node 0x13 [Pin Complex] wcaps 0x400089: Stereo
Pincap 0x0824: IN Detect
Pin Default 0x01813040: [Jack] Line In at Ext Rear
Conn = 1/8, Color = Blue
DefAssociation = 0x4, Sequence = 0x0
Pin-ctls: 0xa0: IN HP
Unsolicited: tag=00, enabled=0
Node 0x14 [Pin Complex] wcaps 0x400089: Stereo
Pincap 0x0824: IN Detect
Pin Default 0x02a19050: [Jack] Mic at Ext Front
Conn = 1/8, Color = Pink
DefAssociation = 0x5, Sequence = 0x0
Pin-ctls: 0xa0: IN HP
Unsolicited: tag=00, enabled=0
Node 0x15 [Pin Complex] wcaps 0x40008b: Stereo Amp-In
Amp-In caps: N/A
Amp-In vals: [0x00 0x00]
Pincap 0x0826: IN Detect Trigger
Pin Default 0x00000000: [Jack] Line Out at Ext N/A
Conn = Unknown, Color = Unknown DefAssociation = 0x0, Sequence = 0x0
Pin-ctls: 0xa0: IN HP
Unsolicited: tag=00, enabled=0
Node 0x16 [Pin Complex] wcaps 0x40008b: Stereo Amp-In
Amp-In caps: N/A
Amp-In vals: [0x00 0x00]
Pincap 0x0826: IN Detect Trigger
Pin Default 0x41911070: [N/A] Aux at Ext Rear
Conn = 1/8, Color = Black
DefAssociation = 0x7, Sequence = 0x0
Pin-ctls: 0xa0: IN HP
Unsolicited: tag=00, enabled=0
Node 0x17 [Pin Complex] wcaps 0x400289: Stereo Digital
Pincap 0x0820: IN
Pin Default 0x01c51180: [Jack] SPDIF In at Ext Rear
Conn = Optical, Color = Black DefAssociation = 0x8, Sequence = 0x0
Misc = NO_PRESENCE
Pin-ctls: 0xa0: IN HP
Unsolicited: tag=00, enabled=0
Node 0x18 [Vendor Defined Widget] wcaps 0xf00080: Mono
Unsolicited: tag=00, enabled=0

_______________________________________________
Alsa-devel mailing list
[email protected]
http://mailman.alsa-project.org/mailman/listinfo/alsa-devel

#1 lore raw

At Sun, 13 Jul 2008 22:51:42 +0100,

Quoted 32 lines · Tony "Chainsaw" Vroon

Good evening,

Just wanted to share that this card seems to be HD-Audio compatible (by virtue of its UAA compatibility claim);
http://uk.europe.creative.com/products/product.asp?category=1&subcategory=208&product=17791

For a while now, I've been trying to write a skeleton patch_creative.c to hook up some basic playback functions. As this has failed, I will instead post all information I can gather about the card, in the hope that such a basic patch_creative.c can be written that I can then slowly extend.
I was unable to set up proper PCM paths (and thus listen to any audio at all), but did manage to get the card detected with a simple addition to hda_intel.c:

(quoted diff) +2 -0
+       /* Creative Labs UAA-compatible */
+       { PCI_DEVICE(0x1102, 0x000b), .driver_data =

AZX_DRIVER_CREATIVE },

A guess at correct mixer controls would be:
HDA_CODEC_VOLUME("PCM Playback Volume", 0x02, 0x0, HDA_OUTPUT), HDA_CODEC_MUTE("PCM Playback Switch", 0x02, 0x0, HDA_OUTPUT), HDA_CODEC_VOLUME("Surround Playback Volume", 0x03, 0x0, HDA_OUTPUT), HDA_CODEC_MUTE("Surround Playback Switch", 0x03, 0x0, HDA_OUTPUT), HDA_CODEC_VOLUME_MONO("Center Playback Volume", 0x04, 1, 0x0, HDA_OUTPUT),
HDA_CODEC_MUTE_MONO("Center Playback Switch", 0x04, 1, 0x0, HDA_OUTPUT), HDA_CODEC_VOLUME_MONO("LFE Playback Volume", 0x04, 2, 0x0, HDA_OUTPUT), HDA_CODEC_MUTE_MONO("LFE Playback Switch", 0x04, 2, 0x0, HDA_OUTPUT), HDA_CODEC_VOLUME("Side Playback Volume", 0x05, 0x0, HDA_OUTPUT), HDA_CODEC_MUTE("Side Playback Switch", 0x05, 0x0, HDA_OUTPUT),

Quoted 1 line

Please find attached the codec details and the resulting codec graph.

Thanks for reporting.
I've had already a test patch on my unstable tree, but it's pending just because of lack of testing with the real hardware.

Could you try the git tree
git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound-unstable-2.6.git
?

If an external ALSA-driver tarball is preferred, get alsa-driver-unstable from the below:
http://ftp.kernel.org/pub/linux/kernel/people/tiwai/snapshot/

thanks,

Takashi

#2 lore raw

Does this hack only work with the X-Fi Titanium Fatal1ty Pro, or does it include support for all X-Fi based cards from Creative Labs? I have got a Creative X-Fi Extreme Music, that gets infact recognized by my system but modprobing the patched source (modprobe snd-hda-intel, i hope this is the right one) does not work.
Here the lspci if this helps:

http://pastebin.com/f6e5fafcb

-- beomuex

Quoted 59 lines · Takashi Iwai

At Sun, 13 Jul 2008 22:51:42 +0100,

Quoted 31 lines · Tony "Chainsaw" Vroon

Good evening,

Just wanted to share that this card seems to be HD-Audio compatible (by virtue of its UAA compatibility claim);
http://uk.europe.creative.com/products/product.asp?category=1&subcategory=208&product=17791

For a while now, I've been trying to write a skeleton patch_creative.c to hook up some basic playback functions. As this has failed, I will instead post all information I can gather about the card, in the hope that such a basic patch_creative.c can be written that I can then slowly extend.
I was unable to set up proper PCM paths (and thus listen to any audio at all), but did manage to get the card detected with a simple addition to hda_intel.c:

(quoted diff) +2 -0
+       /* Creative Labs UAA-compatible */
+       { PCI_DEVICE(0x1102, 0x000b), .driver_data =

AZX_DRIVER_CREATIVE },

A guess at correct mixer controls would be:
HDA_CODEC_VOLUME("PCM Playback Volume", 0x02, 0x0, HDA_OUTPUT), HDA_CODEC_MUTE("PCM Playback Switch", 0x02, 0x0, HDA_OUTPUT), HDA_CODEC_VOLUME("Surround Playback Volume", 0x03, 0x0, HDA_OUTPUT), HDA_CODEC_MUTE("Surround Playback Switch", 0x03, 0x0, HDA_OUTPUT), HDA_CODEC_VOLUME_MONO("Center Playback Volume", 0x04, 1, 0x0, HDA_OUTPUT),
HDA_CODEC_MUTE_MONO("Center Playback Switch", 0x04, 1, 0x0, HDA_OUTPUT), HDA_CODEC_VOLUME_MONO("LFE Playback Volume", 0x04, 2, 0x0, HDA_OUTPUT), HDA_CODEC_MUTE_MONO("LFE Playback Switch", 0x04, 2, 0x0, HDA_OUTPUT), HDA_CODEC_VOLUME("Side Playback Volume", 0x05, 0x0, HDA_OUTPUT), HDA_CODEC_MUTE("Side Playback Switch", 0x05, 0x0, HDA_OUTPUT),

Quoted 2 lines

Please find attached the codec details and the resulting codec graph.

Thanks for reporting.
I've had already a test patch on my unstable tree, but it's pending just because of lack of testing with the real hardware.

Could you try the git tree
git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound-unstable-2.6.git
?

If an external ALSA-driver tarball is preferred, get alsa-driver-unstable from the below:
http://ftp.kernel.org/pub/linux/kernel/people/tiwai/snapshot/

thanks,

Takashi
_______________________________________________
Alsa-devel mailing list
[email protected]
http://mailman.alsa-project.org/mailman/listinfo/alsa-devel

#3 lore raw

At Mon, 14 Jul 2008 15:23:16 +0200,

Quoted 3 lines · Maximilian Güntner

Does this hack only work with the X-Fi Titanium Fatal1ty Pro, or does it include support for all X-Fi based cards from Creative Labs?

It's only for X-Fi with HD-audio compatibility. It's not for native Emu20k stuff.

Quoted 4 lines

I have got a Creative X-Fi Extreme Music, that gets infact recognized by my system but modprobing the patched source (modprobe snd-hda-intel, i hope this is the right one) does not work.
Here the lspci if this helps:

Check "lspci -n". So far, 1102:0009 and 1102:000b are known to be HD-audio compatible.

Takashi

#4 lore raw
Quoted 7 lines · Takashi Iwai
Quoted 3 lines

Does this hack only work with the X-Fi Titanium Fatal1ty Pro, or does it include support for all X-Fi based cards from Creative Labs?

It's only for X-Fi with HD-audio compatibility. It's not for native Emu20k stuff.

HD-audio means what exactly?
How can i see whether a card has this feature or not? The cards you mentioned have all 64 MB X-RAM, mine has only 2 MB. Is this a indication of missing HD-Audio support ?

Quoted 10 lines

I have got a Creative X-Fi Extreme Music, that gets infact recognized by my system but modprobing the patched source (modprobe snd-hda-intel, i hope this is the right one) does not work.
Here the lspci if this helps:

Check "lspci -n". So far, 1102:0009 and 1102:000b are known to be HD-audio compatible.

This is lspci -nn
01:02.0 Multimedia audio controller [0401]: Creative Labs SB X-Fi [1102:0005]

-- beomuex

#5 lore raw

At Mon, 14 Jul 2008 15:59:53 +0200,

Quoted 11 lines · Maximilian Güntner
Quoted 7 lines · Takashi Iwai
Quoted 3 lines

Does this hack only work with the X-Fi Titanium Fatal1ty Pro, or does it include support for all X-Fi based cards from Creative Labs?

It's only for X-Fi with HD-audio compatibility. It's not for native Emu20k stuff.

HD-audio means what exactly?

It means that the board has a compatible mode with Intel HD-audio hardwares, which are seen on most of new PCs as on-board sounds. In this mode, you have no emu20k-specific DSP functionalities but acts just as a dumb playback/capture device.

Quoted 1 line

How can i see whether a card has this feature or not?

Try the driver with your PCI ID, and check whether it works.

Quoted 2 lines

The cards you mentioned have all 64 MB X-RAM, mine has only 2 MB. Is this a indication of missing HD-Audio support ?

It's irrelevant.

Quoted 6 lines
Quoted 6 lines

I have got a Creative X-Fi Extreme Music, that gets infact recognized by my system but modprobing the patched source (modprobe snd-hda-intel, i hope this is the right one) does not work.
Here the lspci if this helps:

Quoted 7 lines
Quoted 4 lines

Check "lspci -n". So far, 1102:0009 and 1102:000b are known to be HD-audio compatible.

This is lspci -nn
01:02.0 Multimedia audio controller [0401]: Creative Labs SB X-Fi [1102:0005]

You can add 1102:0005 to hda_intel.c like the above others.

Takashi

#6 lore raw

Clearly a harder reboot is required, I will power the machine off and unplug it from the AC for a few minutes. A regular powercycle resulted in the following oops report:

ACPI: PCI Interrupt Link [LK2E] enabled at IRQ 47
ACPI: PCI Interrupt 0000:83:00.0[A] -> Link [LK2E] -> GSI 47 (level, high) -> IRQ 47
PCI: Setting latency timer of device 0000:83:00.0 to 64 ALSA sound/pci/hda/hda_intel.c:2022: chipset global capabilities = 0x3500
ALSA sound/pci/hda/hda_intel.c:754: codec_mask = 0x2
ALSA sound/pci/hda/hda_codec.c:3242: autoconfig: line_outs=4 (0xd/0xf/0xe/0x10/0x0)
ALSA sound/pci/hda/hda_codec.c:3246: speaker_outs=0
(0x0/0x0/0x0/0x0/0x0)

ALSA sound/pci/hda/hda_codec.c:3250:    hp_outs=1 (0x11/0x0/0x0/0x0/0x0)
ALSA sound/pci/hda/hda_codec.c:3251:    mono: mono_out=0x0
ALSA sound/pci/hda/hda_codec.c:3259:    inputs: mic=0x14, fmic=0x0,

line=0x13, fline=0x0, cd=0x0, aux=0x0
ALSA sound/pci/hda/hda_codec.c:2336: BUG? (info->nid)
Pid: 1, comm: swapper Not tainted 2.6.26-rc7-00240-gfae47c0 #1

Call Trace:
 [<ffffffff804668ed>] snd_hda_build_pcms+0x1fc/0x29c
 [<ffffffff804ec225>] azx_probe+0x7ed/0x7fd
 [<ffffffff804639b5>] azx_send_cmd+0x0/0x130
 [<ffffffff80463ae5>] azx_get_response+0x0/0x207
 [<ffffffff8046320a>] azx_attach_pcm_stream+0x0/0x1a0
 [<ffffffff80462ed4>] azx_power_notify+0x0/0x51
 [<ffffffff80324bd1>] pci_device_probe+0xa9/0xf6
 [<ffffffff803b138a>] driver_probe_device+0xb5/0x159
 [<ffffffff803b1474>] __driver_attach+0x46/0x6d
 [<ffffffff803b142e>] __driver_attach+0x0/0x6d
 [<ffffffff803b0c9e>] bus_for_each_dev+0x44/0x78
 [<ffffffff803b0630>] bus_add_driver+0xac/0x1e6
 [<ffffffff803b1638>] driver_register+0xa2/0x11f
 [<ffffffff80324e4a>] __pci_register_driver+0x4a/0x7c
 [<ffffffff80660b68>] alsa_card_azx_init+0x0/0x15
 [<ffffffff80644656>] kernel_init+0x146/0x28b
 [<ffffffff8020cc08>] child_rip+0xa/0x12
 [<ffffffff80644510>] kernel_init+0x0/0x28b
 [<ffffffff8020cbfe>] child_rip+0x0/0x12

ACPI: PCI interrupt for device 0000:83:00.0 disabled HDA Intel: probe of 0000:83:00.0 failed with error -22 ALSA device list:
No soundcards found.

Regards,
Tony V.

_______________________________________________
Alsa-devel mailing list
[email protected]
http://mailman.alsa-project.org/mailman/listinfo/alsa-devel

#7 lore raw
In reply to Takashi Iwai
Quoted 3 lines · Takashi Iwai

Could you try the git tree
git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound-unstable-2.6.git
?

Certainly, compiled and running:
Linux prometheus 2.6.26-rc7-00240-gfae47c0 #1 SMP Mon Jul 14 22:10:33 BST 2008 x86_64 Quad-Core AMD Opteron(tm) Processor 2354 AuthenticAMD GNU/Linux

The card is detected, and the auto-detection really seems to do quite well:
ACPI: PCI Interrupt Link [LK2E] enabled at IRQ 47
ACPI: PCI Interrupt 0000:83:00.0[A] -> Link [LK2E] -> GSI 47 (level, high) -> IRQ 47
PCI: Setting latency timer of device 0000:83:00.0 to 64 ALSA sound/pci/hda/hda_intel.c:2022: chipset global capabilities = 0x3500
ALSA sound/pci/hda/hda_intel.c:754: codec_mask = 0x2
ALSA sound/pci/hda/hda_codec.c:3242: autoconfig: line_outs=4 (0xd/0xf/0xe/0x10/0x0)
ALSA sound/pci/hda/hda_codec.c:3246: speaker_outs=0
(0x0/0x0/0x0/0x0/0x0)

ALSA sound/pci/hda/hda_codec.c:3250:    hp_outs=1 (0x11/0x0/0x0/0x0/0x0)
ALSA sound/pci/hda/hda_codec.c:3251:    mono: mono_out=0x0
ALSA sound/pci/hda/hda_codec.c:3259:    inputs: mic=0x14, fmic=0x0,

line=0x13, fline=0x0, cd=0x0, aux=0x0
ALSA device list:
#0: HDA Intel at 0xd0100000 irq 47

Unfortunately, it now reverts to the same "short attention span" problem that I have seen before. This occured when I tried to write a patch_creative.c myself, and I had blamed this on my unfamiliarity with the framework:
hda_codec: num_steps = 0 for NID=0x8 (ctl = Line Capture Volume) ALSA sound/pci/hda/hda_intel.c:601: hda_intel: azx_get_response timeout, switching to polling mode: last cmd=0x101f000a
ALSA sound/pci/hda/hda_intel.c:608: hda_intel: azx_get_response timeout, switching to single_cmd mode: last cmd=0x101f000a
ALSA sound/pci/hda/hda_intel.c:666: hda-intel: get_response timeout:
IRS=0x0

I provoked this with a simple: cat /proc/asound/card0/codec#1

It produces valid-looking output the first time (that I shared with you in my initial e-mail), and then the card's short attention span gets the better of it. It is dead in the water, and no matter how hard ALSA tries, it gets no response out of it:

ALSA sound/pci/hda/hda_intel.c:666: hda-intel: get_response timeout:
IRS=0x0
ALSA sound/pci/hda/hda_intel.c:666: hda-intel: get_response timeout:
IRS=0x0
__ratelimit: 3 messages suppressed
ALSA sound/pci/hda/hda_intel.c:666: hda-intel: get_response timeout:
IRS=0x0
__ratelimit: 85 messages suppressed
ALSA sound/pci/hda/hda_intel.c:666: hda-intel: get_response timeout:
IRS=0x0

Can you perhaps decode the command from the printk to a problematic widget that should be left alone?
I will now powercycle the machine and try to use the soundcard without poking at the codec info.

Note that I've tried this card on MSI as well, and the behaviour is exactly the same (only disabling MSI is another troubleshooting step for the framework, which is equally unsuccessful).
The card displays various completely broken codec configurations once in this state, occasionally causing an 'Invalid AFG subtree' message but usually settling on a GPIO configuration with 255 I/Os (seemingly caused by reading an area of all ones):
GPIO: io=255, o=255, i=255, unsolicited=1, wake=1
IO[0]: enable=1, dir=1, wake=1, sticky=1, data=1
IO[1]: enable=1, dir=1, wake=1, sticky=1, data=1
(and so on)

The mainboard that I'm trying this on is a Tyan Thunder n6650W (S2915-E) on BIOS revision 2.07; the card is in one of the 8-lane PCI-express slots.

Regards,
Tony V.

_______________________________________________
Alsa-devel mailing list
[email protected]
http://mailman.alsa-project.org/mailman/listinfo/alsa-devel

#8 lore raw
In reply to Takashi Iwai

Sorry, I seem unable to reproduce the earlier success even after having the machine without power for over an hour:

ACPI: PCI Interrupt Link [LK2E] enabled at IRQ 47
ACPI: PCI Interrupt 0000:83:00.0[A] -> Link [LK2E] -> GSI 47 (level, high) -> IRQ 47
PCI: Setting latency timer of device 0000:83:00.0 to 64 ALSA sound/pci/hda/hda_intel.c:2022: chipset global capabilities = 0x3500
ALSA sound/pci/hda/hda_intel.c:754: codec_mask = 0x2
ALSA sound/pci/hda/hda_codec.c:3242: autoconfig: line_outs=4 (0xd/0xf/0xe/0x10/0x0)
ALSA sound/pci/hda/hda_codec.c:3246: speaker_outs=0
(0x0/0x0/0x0/0x0/0x0)

ALSA sound/pci/hda/hda_codec.c:3250:    hp_outs=1 (0x11/0x0/0x0/0x0/0x0)
ALSA sound/pci/hda/hda_codec.c:3251:    mono: mono_out=0x0
ALSA sound/pci/hda/hda_codec.c:3259:    inputs: mic=0x14, fmic=0x0,

line=0x13, fline=0x0, cd=0x0, aux=0x0
ALSA sound/pci/hda/hda_codec.c:275: Too many connections ALSA sound/pci/hda/hda_codec.c:2336: BUG? (info->nid)
Pid: 1, comm: swapper Not tainted 2.6.26-rc7-00240-gfae47c0 #1

Call Trace:
 [<ffffffff804668ed>] snd_hda_build_pcms+0x1fc/0x29c
 [<ffffffff804ec225>] azx_probe+0x7ed/0x7fd
 [<ffffffff804639b5>] azx_send_cmd+0x0/0x130
 [<ffffffff80463ae5>] azx_get_response+0x0/0x207
 [<ffffffff8046320a>] azx_attach_pcm_stream+0x0/0x1a0
 [<ffffffff80462ed4>] azx_power_notify+0x0/0x51
 [<ffffffff80324bd1>] pci_device_probe+0xa9/0xf6
 [<ffffffff803b138a>] driver_probe_device+0xb5/0x159
 [<ffffffff803b1474>] __driver_attach+0x46/0x6d
 [<ffffffff803b142e>] __driver_attach+0x0/0x6d
 [<ffffffff803b0c9e>] bus_for_each_dev+0x44/0x78
 [<ffffffff803b0630>] bus_add_driver+0xac/0x1e6
 [<ffffffff803b1638>] driver_register+0xa2/0x11f
 [<ffffffff80324e4a>] __pci_register_driver+0x4a/0x7c
 [<ffffffff80660b68>] alsa_card_azx_init+0x0/0x15
 [<ffffffff80644656>] kernel_init+0x146/0x28b
 [<ffffffff8020cc08>] child_rip+0xa/0x12
 [<ffffffff80644510>] kernel_init+0x0/0x28b
 [<ffffffff8020cbfe>] child_rip+0x0/0x12

ACPI: PCI interrupt for device 0000:83:00.0 disabled HDA Intel: probe of 0000:83:00.0 failed with error -22 ALSA device list:
No soundcards found.

I will power it down now and try again tomorrow. Perhaps you can sprinkle some strategic printk statements?
I'm certainly happy to try different configurations. To confirm, this machine is not in production use and repeated reboots are not an issue.

Regards,
Tony V.

_______________________________________________
Alsa-devel mailing list
[email protected]
http://mailman.alsa-project.org/mailman/listinfo/alsa-devel

#9 lore raw
In reply to Takashi Iwai

Being without power for longer reset it properly, it seems:
ACPI: PCI Interrupt Link [LK2E] enabled at IRQ 47
ACPI: PCI Interrupt 0000:83:00.0[A] -> Link [LK2E] -> GSI 47 (level, high) -> IRQ 47
PCI: Setting latency timer of device 0000:83:00.0 to 64 ALSA sound/pci/hda/hda_intel.c:2022: chipset global capabilities = 0x3500
ALSA sound/pci/hda/hda_intel.c:754: codec_mask = 0x2
ALSA sound/pci/hda/hda_codec.c:3242: autoconfig: line_outs=4 (0xd/0xf/0xe/0x10/0x0)
ALSA sound/pci/hda/hda_codec.c:3246: speaker_outs=0
(0x0/0x0/0x0/0x0/0x0)

ALSA sound/pci/hda/hda_codec.c:3250:    hp_outs=1 (0x11/0x0/0x0/0x0/0x0)
ALSA sound/pci/hda/hda_codec.c:3251:    mono: mono_out=0x0
ALSA sound/pci/hda/hda_codec.c:3259:    inputs: mic=0x14, fmic=0x0,

line=0x13, fline=0x0, cd=0x0, aux=0x0
ALSA device list:
#0: HDA Intel at 0xd0100000 irq 47

The mixer restore script then complained about control #4, saying it was unable to set it; the ALSA mixer state dump contains:

        control.4 {
                comment.access 'read write'
                comment.type INTEGER
                comment.count 2
                comment.range '0 - 31'
                comment.dbmin -3450
                comment.dbmax 1200
                iface MIXER
                name 'Mic Playback Volume'
                value.0 0
                value.1 0
        }

All seemed normal, until I started mplayer and got no audio:
[AO_ALSA] alsa-lib: pcm_dmix.c:996:(snd_pcm_dmix_open) unable to open slave
[AO_ALSA] Playback open error: Invalid argument
Could not open/initialize audio device -> no sound.
Audio: no sound

Kernel-side, things look like the usual 'short attention span' bug:
Pid: 3987, comm: mplayer Not tainted 2.6.26-rc7-00240-gfae47c0 #1

Call Trace:
 [<ffffffff80453c7e>] snd_pcm_hw_constraints_complete+0xbf/0x2b7
 [<ffffffff80453ee8>] snd_pcm_open_substream+0x72/0xb9
 [<ffffffff804ee718>] mutex_lock+0xd/0x1e
 [<ffffffff80453fbe>] snd_pcm_open+0x8f/0x188
 [<ffffffff80228d82>] default_wake_function+0x0/0xe
 [<ffffffff8027f1ec>] exact_lock+0xc/0x14
 [<ffffffff804466f8>] snd_open+0x40/0x53
 [<ffffffff8027f3f6>] chrdev_open+0x120/0x144
 [<ffffffff80285d28>] do_path_lookup+0x1cc/0x1ec
 [<ffffffff8027f2d6>] chrdev_open+0x0/0x144
 [<ffffffff8027b9b1>] __dentry_open+0xe6/0x1e2
 [<ffffffff80286e56>] do_filp_open+0x3ac/0x7f6
 [<ffffffff8027b740>] get_unused_fd_flags+0x7f/0x10e
 [<ffffffff8027b815>] do_sys_open+0x46/0xca
 [<ffffffff8020bdeb>] system_call_after_swapgs+0x7b/0x80

ALSA sound/core/pcm_native.c:2051: snd_pcm_hw_constraints_complete failed
ALSA sound/pci/hda/hda_codec.c:774: hda_codec_cleanup_stream: NID=0x2 ALSA sound/pci/hda/hda_codec.c:774: hda_codec_cleanup_stream: NID=0x4 ALSA sound/pci/hda/hda_codec.c:774: hda_codec_cleanup_stream: NID=0x3 ALSA sound/pci/hda/hda_codec.c:774: hda_codec_cleanup_stream: NID=0x5
hda_codec: num_steps = 0 for NID=0x2 (ctl = Front Playback Volume)
hda_codec: num_steps = 0 for NID=0x4 (ctl = Surround Playback Volume)
hda_codec: num_steps = 0 for NID=0x3 (ctl = Center Playback Volume)
hda_codec: num_steps = 0 for NID=0x3 (ctl = LFE Playback Volume)
hda_codec: num_steps = 0 for NID=0x5 (ctl = Side Playback Volume) ALSA sound/pci/hda/hda_intel.c:601: hda_intel: azx_get_response timeout, switching to polling mode: last cmd=0x102ba000
ALSA sound/pci/hda/hda_intel.c:608: hda_intel: azx_get_response timeout, switching to single_cmd mode: last cmd=0x102ba000
ALSA sound/pci/hda/hda_intel.c:666: hda-intel: get_response timeout:
IRS=0x0
ALSA sound/pci/hda/hda_intel.c:666: hda-intel: get_response timeout:
IRS=0x0
ALSA sound/pci/hda/hda_intel.c:666: hda-intel: get_response timeout:
IRS=0x0
ALSA sound/pci/hda/hda_intel.c:666: hda-intel: get_response timeout:
IRS=0x0
ALSA sound/pci/hda/hda_intel.c:666: hda-intel: get_response timeout:
IRS=0x0
ALSA sound/pci/hda/hda_intel.c:666: hda-intel: get_response timeout:
IRS=0x0
ALSA sound/pci/hda/hda_intel.c:666: hda-intel: get_response timeout:
IRS=0x0
ALSA sound/pci/hda/hda_intel.c:666: hda-intel: get_response timeout:
IRS=0x0
ALSA sound/pci/hda/hda_intel.c:666: hda-intel: get_response timeout:
IRS=0x0
ALSA sound/pci/hda/hda_intel.c:666: hda-intel: get_response timeout:
IRS=0x0
__ratelimit: 455 messages suppressed
ALSA sound/pci/hda/hda_intel.c:666: hda-intel: get_response timeout:
IRS=0x0
__ratelimit: 21 messages suppressed
ALSA sound/pci/hda/hda_intel.c:666: hda-intel: get_response timeout:
IRS=0x0
__ratelimit: 155 messages suppressed
ALSA sound/pci/hda/hda_intel.c:666: hda-intel: get_response timeout:
IRS=0x0

PCM streams are advertised, which is new:
prometheus ~ # aplay -L
default:CARD=Intel
HDA Intel, CA0110 Analog
Default Audio Device
front:CARD=Intel,DEV=0
HDA Intel, CA0110 Analog
Front speakers
surround40:CARD=Intel,DEV=0
HDA Intel, CA0110 Analog
4.0 Surround output to Front and Rear speakers
surround41:CARD=Intel,DEV=0
HDA Intel, CA0110 Analog
4.1 Surround output to Front, Rear and Subwoofer speakers
surround50:CARD=Intel,DEV=0
HDA Intel, CA0110 Analog
5.0 Surround output to Front, Center and Rear speakers
surround51:CARD=Intel,DEV=0
HDA Intel, CA0110 Analog
5.1 Surround output to Front, Center, Rear and Subwoofer speakers
surround71:CARD=Intel,DEV=0
HDA Intel, CA0110 Analog
7.1 Surround output to Front, Center, Side, Rear and Woofer speakers
null
Discard all samples (playback) or generate zero samples (capture)
prometheus ~ # aplay -l
**** List of PLAYBACK Hardware Devices ****
card 0: Intel [HDA Intel], device 0: CA0110 Analog [CA0110 Analog]
Subdevices: 1/1
Subdevice #0: subdevice #0
card 0: Intel [HDA Intel], device 1: CA0110 Digital [CA0110 Digital]
Subdevices: 1/1
Subdevice #0: subdevice #0

Sorry to report that I was too late in capturing codec info, this had already reverted to the phantom 255 GPIOs configuration.

Regards,
Tony V.

_______________________________________________
Alsa-devel mailing list
[email protected]
http://mailman.alsa-project.org/mailman/listinfo/alsa-devel