Skip to contentSkip to conversation

Blackfin RTC Driver updates for 2.6.27

PATCH New Bryan Wu 1 participant 9 messages Jul 27, 2008 Real time clock (RTC)

lore
Share & tools
lore

Bryan Wu

author
#0 lore raw

cover Blackfin RTC Driver updates for 2.6.27

Hi folks,

I remember I sent out most of Blackfin RTC patches before. Maybe in -mm. Here is the whole Blackfin RTC patches in my queue, please take a look.

Thanks a lot
-Bryan

author
#1 lore raw

PATCH 1/8 RTC driver: if we dont define irq_set_freq, the common rtc-dev layer will give us the same behavior of returning ENOTTY

From: Mike Frysinger <[email protected]>

---
 drivers/rtc/rtc-bfin.c |   15 ---------------
 1 files changed, 0 insertions(+), 15 deletions(-)
drivers/rtc/rtc-bfin.c +0 -15
index 8624f55..48ada59 100644
@@ -381,20 +381,6 @@ static int bfin_rtc_proc(struct device *dev, struct seq_file *seq)
 #undef yesno
 }
 
-/**
- *	bfin_irq_set_freq - make sure hardware supports requested freq
- *	@dev: pointer to RTC device structure
- *	@freq: requested frequency rate
- *
- *	The Blackfin RTC can only generate periodic events at 1 per
- *	second (1 Hz), so reject any attempt at changing it.
- */
-static int bfin_irq_set_freq(struct device *dev, int freq)
-{
-	dev_dbg_stamp(dev);
-	return -ENOTTY;
-}
-
 static struct rtc_class_ops bfin_rtc_ops = {
 	.open          = bfin_rtc_open,
 	.release       = bfin_rtc_release,
@@ -404,7 +390,6 @@ static struct rtc_class_ops bfin_rtc_ops = {
 	.read_alarm    = bfin_rtc_read_alarm,
 	.set_alarm     = bfin_rtc_set_alarm,
 	.proc          = bfin_rtc_proc,
-	.irq_set_freq  = bfin_irq_set_freq,
 };
 
 static int __devinit bfin_rtc_probe(struct platform_device *pdev)
Signature · 1 line
1.5.6
author
#2 lore raw

PATCH 2/8 RTC driver: Fix bug Only RTC interrupt can wake up deeper sleep core.

In reply to Bryan Wu

From: Sonic Zhang <[email protected]>

---
 drivers/rtc/rtc-bfin.c |   28 ++++++++++++++++++++++++++++
 1 files changed, 28 insertions(+), 0 deletions(-)
drivers/rtc/rtc-bfin.c +28 -0
index 48ada59..a568d29 100644
@@ -430,6 +430,30 @@ static int __devexit bfin_rtc_remove(struct platform_device *pdev)
 	return 0;
 }
 
+#ifdef CONFIG_PM
+static int bfin_rtc_suspend(struct platform_device *pdev, pm_message_t state)
+{
+#ifdef PM_WAKEUP_SIC_IWR
+	struct bfin_rtc *rtc = dev_get_drvdata(&pdev->dev);
+#endif
+	bfin_rtc_reset(&pdev->dev);
+#ifdef PM_WAKEUP_SIC_IWR
+	bfin_write_RTC_SWCNT(10);
+	bfin_rtc_int_set(rtc, RTC_ISTAT_STOPWATCH);
+#endif
+	return 0;
+}
+
+static int bfin_rtc_resume(struct platform_device *pdev)
+{
+#ifdef PM_WAKEUP_SIC_IWR
+	struct bfin_rtc *rtc = dev_get_drvdata(&pdev->dev);
+	bfin_rtc_int_clear(rtc, RTC_ISTAT_STOPWATCH);
+#endif
+	return 0;
+}
+#endif
+
 static struct platform_driver bfin_rtc_driver = {
 	.driver		= {
 		.name	= "rtc-bfin",
@@ -437,6 +461,10 @@ static struct platform_driver bfin_rtc_driver = {
 	},
 	.probe		= bfin_rtc_probe,
 	.remove		= __devexit_p(bfin_rtc_remove),
+#ifdef CONFIG_PM
+	.suspend	= bfin_rtc_suspend,
+	.resume		= bfin_rtc_resume,
+#endif
 };
 
 static int __init bfin_rtc_init(void)
Signature · 1 line
1.5.6
author
#3 lore raw

PATCH 3/8 RTC driver: add support for power management framework

In reply to Bryan Wu

From: Mike Frysinger <[email protected]>

---
 drivers/rtc/rtc-bfin.c |   31 +++++++++++++++++--------------
 1 files changed, 17 insertions(+), 14 deletions(-)
drivers/rtc/rtc-bfin.c +17 -14
index a568d29..23b991d 100644
@@ -2,7 +2,7 @@
  * Blackfin On-Chip Real Time Clock Driver
  *  Supports BF52[257]/BF53[123]/BF53[467]/BF54[24789]
  *
- * Copyright 2004-2007 Analog Devices Inc.
+ * Copyright 2004-2008 Analog Devices Inc.
  *
  * Enter bugs at http://blackfin.uclinux.org/
  *
@@ -412,6 +412,8 @@ static int __devinit bfin_rtc_probe(struct platform_device *pdev)
 
 	platform_set_drvdata(pdev, rtc);
 
+	device_init_wakeup(&pdev->dev, 1);
+
 	return 0;
 
  err:
@@ -433,25 +435,28 @@ static int __devexit bfin_rtc_remove(struct platform_device *pdev)
 #ifdef CONFIG_PM
 static int bfin_rtc_suspend(struct platform_device *pdev, pm_message_t state)
 {
-#ifdef PM_WAKEUP_SIC_IWR
 	struct bfin_rtc *rtc = dev_get_drvdata(&pdev->dev);
-#endif
-	bfin_rtc_reset(&pdev->dev);
-#ifdef PM_WAKEUP_SIC_IWR
-	bfin_write_RTC_SWCNT(10);
-	bfin_rtc_int_set(rtc, RTC_ISTAT_STOPWATCH);
-#endif
+
+	if (device_may_wakeup(&pdev->dev))
+		enable_irq_wake(IRQ_RTC);
+	else
+		bfin_rtc_int_clear(rtc, -1);
+
 	return 0;
 }
 
 static int bfin_rtc_resume(struct platform_device *pdev)
 {
-#ifdef PM_WAKEUP_SIC_IWR
-	struct bfin_rtc *rtc = dev_get_drvdata(&pdev->dev);
-	bfin_rtc_int_clear(rtc, RTC_ISTAT_STOPWATCH);
-#endif
+	if (device_may_wakeup(&pdev->dev))
+		disable_irq_wake(IRQ_RTC);
+	else
+		bfin_write_RTC_ISTAT(-1);
+
 	return 0;
 }
+#else
+# define bfin_rtc_suspend NULL
+# define bfin_rtc_resume  NULL
 #endif
 
 static struct platform_driver bfin_rtc_driver = {
@@ -461,10 +466,8 @@ static struct platform_driver bfin_rtc_driver = {
 	},
 	.probe		= bfin_rtc_probe,
 	.remove		= __devexit_p(bfin_rtc_remove),
-#ifdef CONFIG_PM
 	.suspend	= bfin_rtc_suspend,
 	.resume		= bfin_rtc_resume,
-#endif
 };
 
 static int __init bfin_rtc_init(void)
Signature · 1 line
1.5.6
author
#4 lore raw

PATCH 4/8 RTC driver: dont bother passing the rtc struct down to bfin_rtc_int_{set,clear} since it isnt needed (shaves off ~100bytes)

In reply to Bryan Wu

From: Mike Frysinger <[email protected]>

---
 drivers/rtc/rtc-bfin.c |   20 +++++++++-----------
 1 files changed, 9 insertions(+), 11 deletions(-)
drivers/rtc/rtc-bfin.c +9 -11
index 23b991d..56656dd 100644
@@ -238,12 +238,12 @@ static void bfin_rtc_release(struct device *dev)
 	free_irq(IRQ_RTC, dev);
 }
 
-static void bfin_rtc_int_set(struct bfin_rtc *rtc, u16 rtc_int)
+static void bfin_rtc_int_set(u16 rtc_int)
 {
 	bfin_write_RTC_ISTAT(rtc_int);
 	bfin_write_RTC_ICTL(bfin_read_RTC_ICTL() | rtc_int);
 }
-static void bfin_rtc_int_clear(struct bfin_rtc *rtc, u16 rtc_int)
+static void bfin_rtc_int_clear(u16 rtc_int)
 {
 	bfin_write_RTC_ICTL(bfin_read_RTC_ICTL() & rtc_int);
 }
@@ -252,7 +252,7 @@ static void bfin_rtc_int_set_alarm(struct bfin_rtc *rtc)
 	/* Blackfin has different bits for whether the alarm is
 	 * more than 24 hours away.
 	 */
-	bfin_rtc_int_set(rtc, (rtc->rtc_alarm.tm_yday == -1 ? RTC_ISTAT_ALARM : RTC_ISTAT_ALARM_DAY));
+	bfin_rtc_int_set(rtc->rtc_alarm.tm_yday == -1 ? RTC_ISTAT_ALARM : RTC_ISTAT_ALARM_DAY);
 }
 static int bfin_rtc_ioctl(struct device *dev, unsigned int cmd, unsigned long arg)
 {
@@ -266,21 +266,21 @@ static int bfin_rtc_ioctl(struct device *dev, unsigned int cmd, unsigned long ar
 	switch (cmd) {
 	case RTC_PIE_ON:
 		dev_dbg_stamp(dev);
-		bfin_rtc_int_set(rtc, RTC_ISTAT_STOPWATCH);
+		bfin_rtc_int_set(RTC_ISTAT_STOPWATCH);
 		bfin_write_RTC_SWCNT(rtc->rtc_dev->irq_freq);
 		break;
 	case RTC_PIE_OFF:
 		dev_dbg_stamp(dev);
-		bfin_rtc_int_clear(rtc, ~RTC_ISTAT_STOPWATCH);
+		bfin_rtc_int_clear(~RTC_ISTAT_STOPWATCH);
 		break;
 
 	case RTC_UIE_ON:
 		dev_dbg_stamp(dev);
-		bfin_rtc_int_set(rtc, RTC_ISTAT_SEC);
+		bfin_rtc_int_set(RTC_ISTAT_SEC);
 		break;
 	case RTC_UIE_OFF:
 		dev_dbg_stamp(dev);
-		bfin_rtc_int_clear(rtc, ~RTC_ISTAT_SEC);
+		bfin_rtc_int_clear(~RTC_ISTAT_SEC);
 		break;
 
 	case RTC_AIE_ON:
@@ -289,7 +289,7 @@ static int bfin_rtc_ioctl(struct device *dev, unsigned int cmd, unsigned long ar
 		break;
 	case RTC_AIE_OFF:
 		dev_dbg_stamp(dev);
-		bfin_rtc_int_clear(rtc, ~(RTC_ISTAT_ALARM | RTC_ISTAT_ALARM_DAY));
+		bfin_rtc_int_clear(~(RTC_ISTAT_ALARM | RTC_ISTAT_ALARM_DAY));
 		break;
 
 	default:
@@ -435,12 +435,10 @@ static int __devexit bfin_rtc_remove(struct platform_device *pdev)
 #ifdef CONFIG_PM
 static int bfin_rtc_suspend(struct platform_device *pdev, pm_message_t state)
 {
-	struct bfin_rtc *rtc = dev_get_drvdata(&pdev->dev);
-
 	if (device_may_wakeup(&pdev->dev))
 		enable_irq_wake(IRQ_RTC);
 	else
-		bfin_rtc_int_clear(rtc, -1);
+		bfin_rtc_int_clear(-1);
 
 	return 0;
 }
Signature · 1 line
1.5.6
author
#5 lore raw

PATCH 5/8 Blackfin RTC Driver: disable the write complete irq upon close

In reply to Bryan Wu

From: Mike Frysinger <[email protected]>

---
 drivers/rtc/rtc-bfin.c |    8 ++++----
 1 files changed, 4 insertions(+), 4 deletions(-)
drivers/rtc/rtc-bfin.c +4 -4
index 56656dd..d53772f 100644
@@ -144,13 +144,13 @@ static void bfin_rtc_sync_pending(struct device *dev)
  * Initialize the RTC.  Enable pre-scaler to scale RTC clock
  * to 1Hz and clear interrupt/status registers.
  */
-static void bfin_rtc_reset(struct device *dev)
+static void bfin_rtc_reset(struct device *dev, u16 rtc_ictl)
 {
 	struct bfin_rtc *rtc = dev_get_drvdata(dev);
 	dev_dbg_stamp(dev);
 	bfin_rtc_sync_pending(dev);
 	bfin_write_RTC_PREN(0x1);
-	bfin_write_RTC_ICTL(RTC_ISTAT_WRITE_COMPLETE);
+	bfin_write_RTC_ICTL(rtc_ictl);
 	bfin_write_RTC_SWCNT(0);
 	bfin_write_RTC_ALARM(0);
 	bfin_write_RTC_ISTAT(0xFFFF);
@@ -226,7 +226,7 @@ static int bfin_rtc_open(struct device *dev)
 
 	ret = request_irq(IRQ_RTC, bfin_rtc_interrupt, IRQF_SHARED, to_platform_device(dev)->name, dev);
 	if (!ret)
-		bfin_rtc_reset(dev);
+		bfin_rtc_reset(dev, RTC_ISTAT_WRITE_COMPLETE);
 
 	return ret;
 }
@@ -234,7 +234,7 @@ static int bfin_rtc_open(struct device *dev)
 static void bfin_rtc_release(struct device *dev)
 {
 	dev_dbg_stamp(dev);
-	bfin_rtc_reset(dev);
+	bfin_rtc_reset(dev, 0);
 	free_irq(IRQ_RTC, dev);
 }
 
Signature · 1 line
1.5.6
author
#6 lore raw

PATCH 6/8 Blackfin RTC Driver: wait for the write complete interrupt complete before sleeping

In reply to Bryan Wu

From: Mike Frysinger <[email protected]>

Since we use the write complete interrupt, wait for it
to complete before sleeping so we don't wake right back up due to it

---
 drivers/rtc/rtc-bfin.c |    5 +++--
 1 files changed, 3 insertions(+), 2 deletions(-)
drivers/rtc/rtc-bfin.c +3 -2
index d53772f..e6b0470 100644
@@ -435,9 +435,10 @@ static int __devexit bfin_rtc_remove(struct platform_device *pdev)
 #ifdef CONFIG_PM
 static int bfin_rtc_suspend(struct platform_device *pdev, pm_message_t state)
 {
-	if (device_may_wakeup(&pdev->dev))
+	if (device_may_wakeup(&pdev->dev)) {
 		enable_irq_wake(IRQ_RTC);
-	else
+		bfin_rtc_sync_pending(&pdev->dev);
+	} else
 		bfin_rtc_int_clear(-1);
 
 	return 0;
Signature · 1 line
1.5.6
author
#7 lore raw

PATCH 7/8 Blackfin RTC Driver: convert PIE handling to irq_set_state() as pointed out by David Brownell

In reply to Bryan Wu

From: Mike Frysinger <[email protected]>

---
 drivers/rtc/rtc-bfin.c |   28 ++++++++++++++++++----------
 1 files changed, 18 insertions(+), 10 deletions(-)
drivers/rtc/rtc-bfin.c +18 -10
index e6b0470..ceebce7 100644
@@ -264,16 +264,6 @@ static int bfin_rtc_ioctl(struct device *dev, unsigned int cmd, unsigned long ar
 	bfin_rtc_sync_pending(dev);
 
 	switch (cmd) {
-	case RTC_PIE_ON:
-		dev_dbg_stamp(dev);
-		bfin_rtc_int_set(RTC_ISTAT_STOPWATCH);
-		bfin_write_RTC_SWCNT(rtc->rtc_dev->irq_freq);
-		break;
-	case RTC_PIE_OFF:
-		dev_dbg_stamp(dev);
-		bfin_rtc_int_clear(~RTC_ISTAT_STOPWATCH);
-		break;
-
 	case RTC_UIE_ON:
 		dev_dbg_stamp(dev);
 		bfin_rtc_int_set(RTC_ISTAT_SEC);
@@ -381,6 +371,23 @@ static int bfin_rtc_proc(struct device *dev, struct seq_file *seq)
 #undef yesno
 }
 
+static int bfin_irq_set_state(struct device *dev, int enabled)
+{
+	struct bfin_rtc *rtc = dev_get_drvdata(dev);
+
+	dev_dbg_stamp(dev);
+
+	bfin_rtc_sync_pending(dev);
+
+	if (enabled) {
+		bfin_rtc_int_set(RTC_ISTAT_STOPWATCH);
+		bfin_write_RTC_SWCNT(rtc->rtc_dev->irq_freq);
+	} else
+		bfin_rtc_int_clear(~RTC_ISTAT_STOPWATCH);
+
+	return 0;
+}
+
 static struct rtc_class_ops bfin_rtc_ops = {
 	.open          = bfin_rtc_open,
 	.release       = bfin_rtc_release,
@@ -390,6 +397,7 @@ static struct rtc_class_ops bfin_rtc_ops = {
 	.read_alarm    = bfin_rtc_read_alarm,
 	.set_alarm     = bfin_rtc_set_alarm,
 	.proc          = bfin_rtc_proc,
+	.irq_set_state = bfin_irq_set_state,
 };
 
 static int __devinit bfin_rtc_probe(struct platform_device *pdev)
Signature · 1 line
1.5.6
author
#8 lore raw

PATCH 8/8 Blackfin RTC Driver: drop PIE/stopwatch code since the hardware can only do a max of 1HZ and this same functionality is provided by UIE

In reply to Bryan Wu

From: Mike Frysinger <[email protected]>

---
 drivers/rtc/rtc-bfin.c |   46 ++++++++++++++--------------------------------
 1 files changed, 14 insertions(+), 32 deletions(-)
drivers/rtc/rtc-bfin.c +14 -32
index ceebce7..a1af4c2 100644
@@ -32,6 +32,15 @@
  * writes to clear status registers complete immediately.
  */
 
+/* It may seem odd that there is no SWCNT code in here (which would be exposed
+ * via the periodic interrupt event, or PIE).  Since the Blackfin RTC peripheral
+ * runs in units of seconds (N/HZ) but the Linux framework runs in units of HZ
+ * (2^N HZ), there is no point in keeping code that only provides 1 HZ PIEs.
+ * The same exact behavior can be accomplished by using the update interrupt
+ * event (UIE).  Maybe down the line the RTC peripheral will suck less in which
+ * case we can re-introduce PIE support.
+ */
+
 #include <linux/bcd.h>
 #include <linux/completion.h>
 #include <linux/delay.h>
@@ -151,7 +160,6 @@ static void bfin_rtc_reset(struct device *dev, u16 rtc_ictl)
 	bfin_rtc_sync_pending(dev);
 	bfin_write_RTC_PREN(0x1);
 	bfin_write_RTC_ICTL(rtc_ictl);
-	bfin_write_RTC_SWCNT(0);
 	bfin_write_RTC_ALARM(0);
 	bfin_write_RTC_ISTAT(0xFFFF);
 	rtc->rtc_wrote_regs = 0;
@@ -194,14 +202,6 @@ static irqreturn_t bfin_rtc_interrupt(int irq, void *dev_id)
 		}
 	}
 
-	if (rtc_ictl & RTC_ISTAT_STOPWATCH) {
-		if (rtc_istat & RTC_ISTAT_STOPWATCH) {
-			bfin_write_RTC_ISTAT(RTC_ISTAT_STOPWATCH);
-			events |= RTC_PF | RTC_IRQF;
-			bfin_write_RTC_SWCNT(rtc->rtc_dev->irq_freq);
-		}
-	}
-
 	if (rtc_ictl & RTC_ISTAT_SEC) {
 		if (rtc_istat & RTC_ISTAT_SEC) {
 			bfin_write_RTC_ISTAT(RTC_ISTAT_SEC);
@@ -361,33 +361,14 @@ static int bfin_rtc_proc(struct device *dev, struct seq_file *seq)
 	seq_printf(seq,
 		"alarm_IRQ\t: %s\n"
 		"wkalarm_IRQ\t: %s\n"
-		"seconds_IRQ\t: %s\n"
-		"periodic_IRQ\t: %s\n",
+		"seconds_IRQ\t: %s\n",
 		yesno(ictl & RTC_ISTAT_ALARM),
 		yesno(ictl & RTC_ISTAT_ALARM_DAY),
-		yesno(ictl & RTC_ISTAT_SEC),
-		yesno(ictl & RTC_ISTAT_STOPWATCH));
+		yesno(ictl & RTC_ISTAT_SEC));
 	return 0;
 #undef yesno
 }
 
-static int bfin_irq_set_state(struct device *dev, int enabled)
-{
-	struct bfin_rtc *rtc = dev_get_drvdata(dev);
-
-	dev_dbg_stamp(dev);
-
-	bfin_rtc_sync_pending(dev);
-
-	if (enabled) {
-		bfin_rtc_int_set(RTC_ISTAT_STOPWATCH);
-		bfin_write_RTC_SWCNT(rtc->rtc_dev->irq_freq);
-	} else
-		bfin_rtc_int_clear(~RTC_ISTAT_STOPWATCH);
-
-	return 0;
-}
-
 static struct rtc_class_ops bfin_rtc_ops = {
 	.open          = bfin_rtc_open,
 	.release       = bfin_rtc_release,
@@ -397,7 +378,6 @@ static struct rtc_class_ops bfin_rtc_ops = {
 	.read_alarm    = bfin_rtc_read_alarm,
 	.set_alarm     = bfin_rtc_set_alarm,
 	.proc          = bfin_rtc_proc,
-	.irq_set_state = bfin_irq_set_state,
 };
 
 static int __devinit bfin_rtc_probe(struct platform_device *pdev)
@@ -416,7 +396,9 @@ static int __devinit bfin_rtc_probe(struct platform_device *pdev)
 		ret = PTR_ERR(rtc->rtc_dev);
 		goto err;
 	}
-	rtc->rtc_dev->irq_freq = 1;
+
+	/* see comment at top of file about stopwatch/PIE */
+	bfin_write_RTC_SWCNT(0);
 
 	platform_set_drvdata(pdev, rtc);
 
Signature · 1 line
1.5.6