Signed-of-by Yinghai Lu <[email protected]>
--- arch/x86/kernel/apic.c | 92 ++----------------------------------------------- 1 file changed, 5 insertions(+), 87 deletions(-)
arch/x86/kernel/apic.c +2 -86
@@ -478,90 +478,6 @@ static void __cpuinit setup_APIC_timer(vclockevents_register_device (levt); } -#ifdef CONFIG_X86_64 -/* -* In this function we calibrate APIC bus clocks to the external -* timer. Unfortunately we cannot use jiffies and the timer irq -* to calibrate, since some later bootup code depends on getting -* the first irq? Ugh. -* -* We want to do the calibration only once since we -* want to have local timer irqs syncron. CPUs connected -* by the same APIC bus have the very same bus frequency. -* And we want to have irqs off anyways, no accidental -* APIC irq that way. -*/ - -#define TICK_COUNT 100000000 - -static int __init calibrate_APIC_clock (void ) -{ -unsigned apic, apic_start; -unsigned long tsc, tsc_start; -int result; - -local_irq_disable (); - -/* -* Put whatever arbitrary (but long enough) timeout -* value into the APIC clock, we just want to get the -* counter running for calibration. -* -* No interrupt enable ! -*/ -__setup_APIC_LVTT (250000000 ,0 ,0 ); - - apic_start =apic_read (APIC_TMCCT ); -#ifdef CONFIG_X86_PM_TIMER -if (apic_calibrate_pmtmr && pmtmr_ioport) { -pmtimer_wait (5000 );/* 5ms wait */ - apic =apic_read (APIC_TMCCT ); - result = (apic_start - apic) *1000L /5 ; - } else -#endif - { -rdtscll (tsc_start); - -do { - apic =apic_read (APIC_TMCCT ); -rdtscll (tsc); - }while ((tsc - tsc_start) <TICK_COUNT && - (apic_start - apic) <TICK_COUNT ); - - result = (apic_start - apic) *1000L * tsc_khz / - (tsc - tsc_start); - } - -local_irq_enable (); - -printk (KERN_DEBUG "APIC timer calibration result %d\n" , result); - -printk (KERN_INFO "Detected %d.%03d MHz APIC timer.\n" , - result /1000 /1000 , result /1000 %1000 ); - -/* Calculate the scaled math multiplication factor */ - lapic_clockevent.mult =div_sc (result,NSEC_PER_SEC , - lapic_clockevent.shift); - lapic_clockevent.max_delta_ns = -clockevent_delta2ns (0x7FFFFF , &lapic_clockevent); - lapic_clockevent.min_delta_ns = -clockevent_delta2ns (0xF , &lapic_clockevent); - - calibration_result = (result *APIC_DIVISOR ) /HZ ; - -/* -* Do a sanity check on the APIC calibration result -*/ -if (calibration_result < (1000000 /HZ )) { -printk (KERN_WARNING -"APIC frequency too slow, disabling apic timer\n" ); -return -1 ; - } - -return 0 ; -} - -#else /* * In this functions we calibrate APIC bus clocks to the external timer. *
@@ -659,6 +575,7 @@ static int __init calibrate_APIC_clock(v delta = lapic_cal_t1 - lapic_cal_t2;apic_printk (APIC_VERBOSE ,"... lapic delta = %ld\n" , delta); +#ifdef CONFIG_X86_PM_TIMER /* Check, if the PM timer is available */ deltapm = lapic_cal_pm2 - lapic_cal_pm1;apic_printk (APIC_VERBOSE ,"... PM timer delta = %ld\n" , deltapm);
@@ -687,6 +604,7 @@ static int __init calibrate_APIC_clock(v } pm_referenced =1 ; } +#endif /* Calculate the scaled math multiplication factor */ lapic_clockevent.mult = div_sc(delta, TICK_NSEC * LAPIC_CAL_LOOPS,
@@ -773,8 +691,6 @@ static int __init calibrate_APIC_clock(vreturn 0 ; } -#endif -/* * Setup the boot APIC *