ST31500341AS vs ICH10, exception Emask 0x50 SAct 0x1 SErr 0x280900 action 0x6 frozen

DISCUSSION Soeren Sonnenburg 3 participants 5 messages Dec 2, 2008 – Dec 4, 2008 libata

Share & tools

Soeren Sonnenburg

author

2008-12-02 08:08 UTC #0 lore raw

Dear all,

I just purchased a seagate 1.5TB drive ST31500341AS, with firmware revision CC1G (which according to seagate is not affected by the cache flush bug) and I am getting the errors below (after almost a day of uptime without problems). The drive is replacing a 750G variant from seagate with which I had months of uptime and no errors whatsoever.

I hope anyone has an idea?

- relevant part of hdparm -I and lspci

ATA device, with non-removable media

	Model Number:       ST31500341AS                            
	Firmware Revision:  CC1G    
	Transport:          Serial

00:1f.2 SATA controller: Intel Corporation 82801JI (ICH10 Family) SATA AHCI Controller

- the error(tm)

ata3.00: exception Emask 0x50 SAct 0x1 SErr 0x280900 action 0x6 frozen ata3.00: irq_stat 0x08000000, interface fatal error
ata3: SError: { UnrecovData HostInt 10B8B BadCRC }
ata3.00: cmd 60/00:00:20:d4:66/01:00:1e:00:00/40 tag 0 ncq 131072 in

         res 40/00:00:20:d4:66/00:00:1e:00:00/40 Emask 0x50 (ATA bus error)

ata3.00: status: { DRDY }
ata3: hard resetting link
ata3: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
ata3.00: both IDENTIFYs aborted, assuming NODEV
ata3.00: revalidation failed (errno=-2)
ata3: hard resetting link
ata3: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
ata3.00: configured for UDMA/133
ata3: EH complete
sd 2:0:0:0: [sdc] 2930277168 512-byte hardware sectors (1500302 MB)
sd 2:0:0:0: [sdc] Write Protect is off
sd 2:0:0:0: [sdc] Mode Sense: 00 3a 00 00
sd 2:0:0:0: [sdc] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA ata3.00: exception Emask 0x10 SAct 0x1 SErr 0x280100 action 0x6 frozen ata3.00: irq_stat 0x08000000, interface fatal error
ata3: SError: { UnrecovData 10B8B BadCRC }
ata3.00: cmd 60/00:00:30:12:67/01:00:1e:00:00/40 tag 0 ncq 131072 in

         res 40/00:00:30:12:67/00:00:1e:00:00/40 Emask 0x10 (ATA bus error)

         res 40/00:00:30:17:67/00:00:1e:00:00/40 Emask 0x10 (ATA bus error)

ata3.00: status: { DRDY }
ata3: hard resetting link
ata3: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
ata3.00: both IDENTIFYs aborted, assuming NODEV
ata3.00: revalidation failed (errno=-2)
ata3: hard resetting link
ata3: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
ata3.00: configured for UDMA/133
ata3: EH complete
sd 2:0:0:0: [sdc] 2930277168 512-byte hardware sectors (1500302 MB)
sd 2:0:0:0: [sdc] Write Protect is off
sd 2:0:0:0: [sdc] Mode Sense: 00 3a 00 00
sd 2:0:0:0: [sdc] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
ata3: limiting SATA link speed to 1.5 Gbps
ata3.00: exception Emask 0x10 SAct 0x1 SErr 0x280100 action 0x6 frozen ata3.00: irq_stat 0x08000000, interface fatal error
ata3: SError: { UnrecovData 10B8B BadCRC }
ata3.00: cmd 60/00:00:30:19:67/01:00:1e:00:00/40 tag 0 ncq 131072 in

         res 40/00:00:30:19:67/00:00:1e:00:00/40 Emask 0x10 (ATA bus error)

ata3.00: status: { DRDY }
ata3: hard resetting link
ata3: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
ata3.00: both IDENTIFYs aborted, assuming NODEV
ata3.00: revalidation failed (errno=-2)
ata3: hard resetting link
ata3: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
ata3.00: configured for UDMA/133
ata3: exception Emask 0x40 SAct 0x0 SErr 0x80800 action 0x7 t4
ata3: irq_stat 0x40000001
ata3: SError: { HostInt 10B8B }
ata3: hard resetting link
ata3: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
ata3.00: failed to IDENTIFY (I/O error, err_mask=0x100)
ata3.00: revalidation failed (errno=-5)
ata3: hard resetting link
ata3: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
ata3.00: configured for UDMA/133
ata3: exception Emask 0x50 SAct 0x0 SErr 0x80800 action 0x7 t3
ata3: irq_stat 0x08000002, interface fatal error
ata3: SError: { HostInt 10B8B }
ata3: hard resetting link
ata3: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
ata3.00: configured for UDMA/133
ata3: EH complete
sd 2:0:0:0: [sdc] 2930277168 512-byte hardware sectors (1500302 MB)
sd 2:0:0:0: [sdc] Write Protect is off
sd 2:0:0:0: [sdc] Mode Sense: 00 3a 00 00
sd 2:0:0:0: [sdc] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA sd 2:0:0:0: [sdc] 2930277168 512-byte hardware sectors (1500302 MB)
sd 2:0:0:0: [sdc] Write Protect is off
sd 2:0:0:0: [sdc] Mode Sense: 00 3a 00 00
sd 2:0:0:0: [sdc] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA ata3.00: exception Emask 0x50 SAct 0x3 SErr 0x280900 action 0x6 frozen ata3.00: irq_stat 0x08000000, interface fatal error
ata3: SError: { UnrecovData HostInt 10B8B BadCRC }
ata3.00: cmd 60/00:00:30:19:67/01:00:1e:00:00/40 tag 0 ncq 131072 in

         res 40/00:08:30:1a:67/00:00:1e:00:00/40 Emask 0x50 (ATA bus error)
ata3.00: status: { DRDY }
ata3.00: cmd 60/00:08:30:1a:67/01:00:1e:00:00/40 tag 1 ncq 131072 in
         res 40/00:08:30:1a:67/00:00:1e:00:00/40 Emask 0x50 (ATA bus error)

ata3.00: status: { DRDY }
ata3: hard resetting link
ata3: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
ata3.00: both IDENTIFYs aborted, assuming NODEV
ata3.00: revalidation failed (errno=-2)
ata3: hard resetting link
ata3: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
ata3.00: configured for UDMA/133
ata3: exception Emask 0x40 SAct 0x0 SErr 0x80800 action 0x7 t4
ata3: irq_stat 0x40000001
ata3: SError: { HostInt 10B8B }
ata3: hard resetting link
ata3: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
ata3.00: configured for UDMA/133
ata3: EH complete
sd 2:0:0:0: [sdc] 2930277168 512-byte hardware sectors (1500302 MB)
sd 2:0:0:0: [sdc] Write Protect is off
sd 2:0:0:0: [sdc] Mode Sense: 00 3a 00 00
sd 2:0:0:0: [sdc] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA sd 2:0:0:0: [sdc] 2930277168 512-byte hardware sectors (1500302 MB)
sd 2:0:0:0: [sdc] Write Protect is off
sd 2:0:0:0: [sdc] Mode Sense: 00 3a 00 00
sd 2:0:0:0: [sdc] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA ata3.00: exception Emask 0x50 SAct 0x3 SErr 0x280900 action 0x6 frozen ata3.00: irq_stat 0x08000000, interface fatal error
ata3: SError: { UnrecovData HostInt 10B8B BadCRC }
ata3.00: cmd 60/00:00:30:1a:67/01:00:1e:00:00/40 tag 0 ncq 131072 in

         res 40/00:08:30:19:67/00:00:1e:00:00/40 Emask 0x50 (ATA bus error)
ata3.00: status: { DRDY }
ata3.00: cmd 60/00:08:30:19:67/01:00:1e:00:00/40 tag 1 ncq 131072 in
         res 40/00:08:30:19:67/00:00:1e:00:00/40 Emask 0x50 (ATA bus error)

ata3.00: status: { DRDY }
ata3: hard resetting link
ata3: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
ata3.00: both IDENTIFYs aborted, assuming NODEV
ata3.00: revalidation failed (errno=-2)
ata3: hard resetting link
ata3: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
ata3.00: configured for UDMA/133
ata3: exception Emask 0x40 SAct 0x0 SErr 0x80800 action 0x7 t4
ata3: irq_stat 0x40000001
ata3: SError: { HostInt 10B8B }
ata3: hard resetting link
ata3: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
ata3.00: configured for UDMA/133
ata3: EH complete
sd 2:0:0:0: [sdc] 2930277168 512-byte hardware sectors (1500302 MB)
sd 2:0:0:0: [sdc] Write Protect is off
sd 2:0:0:0: [sdc] Mode Sense: 00 3a 00 00
sd 2:0:0:0: [sdc] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA sd 2:0:0:0: [sdc] 2930277168 512-byte hardware sectors (1500302 MB)
sd 2:0:0:0: [sdc] Write Protect is off
sd 2:0:0:0: [sdc] Mode Sense: 00 3a 00 00
sd 2:0:0:0: [sdc] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA ata3.00: limiting speed to UDMA/100:PIO4
ata3.00: exception Emask 0x50 SAct 0x3 SErr 0x280900 action 0x6 frozen ata3.00: irq_stat 0x08000000, interface fatal error
ata3: SError: { UnrecovData HostInt 10B8B BadCRC }
ata3.00: cmd 60/00:00:30:19:67/01:00:1e:00:00/40 tag 0 ncq 131072 in

         res 40/00:08:30:1a:67/00:00:1e:00:00/40 Emask 0x50 (ATA bus error)
ata3.00: status: { DRDY }
ata3.00: cmd 60/00:08:30:1a:67/01:00:1e:00:00/40 tag 1 ncq 131072 in
         res 40/00:08:30:1a:67/00:00:1e:00:00/40 Emask 0x50 (ATA bus error)

ata3.00: status: { DRDY }
ata3: hard resetting link
ata3: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
ata3.00: both IDENTIFYs aborted, assuming NODEV
ata3.00: revalidation failed (errno=-2)
ata3: hard resetting link
ata3: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
ata3.00: configured for UDMA/100
ata3: exception Emask 0x40 SAct 0x0 SErr 0x80800 action 0x7 t4
ata3: irq_stat 0x40000001
ata3: SError: { HostInt 10B8B }
ata3: hard resetting link
ata3: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
ata3.00: configured for UDMA/100
ata3: EH complete
sd 2:0:0:0: [sdc] 2930277168 512-byte hardware sectors (1500302 MB)
sd 2:0:0:0: [sdc] Write Protect is off
sd 2:0:0:0: [sdc] Mode Sense: 00 3a 00 00
sd 2:0:0:0: [sdc] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA sd 2:0:0:0: [sdc] 2930277168 512-byte hardware sectors (1500302 MB)
sd 2:0:0:0: [sdc] Write Protect is off
sd 2:0:0:0: [sdc] Mode Sense: 00 3a 00 00
sd 2:0:0:0: [sdc] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA ata3.00: exception Emask 0x50 SAct 0x3 SErr 0x280900 action 0x6 frozen ata3.00: irq_stat 0x08000000, interface fatal error
ata3: SError: { UnrecovData HostInt 10B8B BadCRC }
ata3.00: cmd 60/00:00:30:1a:67/01:00:1e:00:00/40 tag 0 ncq 131072 in

         res 40/00:08:30:19:67/00:00:1e:00:00/40 Emask 0x50 (ATA bus error)
ata3.00: status: { DRDY }
ata3.00: cmd 60/00:08:30:19:67/01:00:1e:00:00/40 tag 1 ncq 131072 in
         res 40/00:08:30:19:67/00:00:1e:00:00/40 Emask 0x50 (ATA bus error)

ata3.00: status: { DRDY }
ata3: hard resetting link
ata3: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
ata3.00: both IDENTIFYs aborted, assuming NODEV
ata3.00: revalidation failed (errno=-2)
ata3: hard resetting link
ata3: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
ata3.00: configured for UDMA/100
ata3: exception Emask 0x40 SAct 0x0 SErr 0x80800 action 0x7 t4
ata3: irq_stat 0x40000001
ata3: SError: { HostInt 10B8B }
ata3: hard resetting link
ata3: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
ata3.00: configured for UDMA/100
ata3: EH complete
sd 2:0:0:0: [sdc] 2930277168 512-byte hardware sectors (1500302 MB)
sd 2:0:0:0: [sdc] Write Protect is off
sd 2:0:0:0: [sdc] Mode Sense: 00 3a 00 00
sd 2:0:0:0: [sdc] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA sd 2:0:0:0: [sdc] 2930277168 512-byte hardware sectors (1500302 MB)
sd 2:0:0:0: [sdc] Write Protect is off
sd 2:0:0:0: [sdc] Mode Sense: 00 3a 00 00
sd 2:0:0:0: [sdc] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA ata3.00: limiting speed to UDMA/33:PIO4
ata3.00: exception Emask 0x50 SAct 0x3 SErr 0x280900 action 0x6 frozen ata3.00: irq_stat 0x08000000, interface fatal error
ata3: SError: { UnrecovData HostInt 10B8B BadCRC }
ata3.00: cmd 60/00:00:30:19:67/01:00:1e:00:00/40 tag 0 ncq 131072 in

         res 40/00:08:30:1a:67/00:00:1e:00:00/40 Emask 0x50 (ATA bus error)
ata3.00: status: { DRDY }
ata3.00: cmd 60/00:08:30:1a:67/01:00:1e:00:00/40 tag 1 ncq 131072 in
         res 40/00:08:30:1a:67/00:00:1e:00:00/40 Emask 0x50 (ATA bus error)

        72 0b 00 00 00 00 00 0c 00 0a 80 00 00 00 00 00 
        1e 67 1a 30

sd 2:0:0:0: [sdc] Add. Sense: No additional sense information
end_request: I/O error, dev sdc, sector 510073136
ata3: EH complete
sd 2:0:0:0: [sdc] 2930277168 512-byte hardware sectors (1500302 MB)
sd 2:0:0:0: [sdc] Write Protect is off
sd 2:0:0:0: [sdc] Mode Sense: 00 3a 00 00
sd 2:0:0:0: [sdc] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA sd 2:0:0:0: [sdc] 2930277168 512-byte hardware sectors (1500302 MB)
sd 2:0:0:0: [sdc] Write Protect is off
sd 2:0:0:0: [sdc] Mode Sense: 00 3a 00 00
sd 2:0:0:0: [sdc] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA ata3.00: exception Emask 0x50 SAct 0x3 SErr 0x280900 action 0x6 frozen ata3.00: irq_stat 0x08000000, interface fatal error
ata3: SError: { UnrecovData HostInt 10B8B BadCRC }
ata3.00: cmd 60/00:00:30:1a:67/01:00:1e:00:00/40 tag 0 ncq 131072 in

         res 40/00:08:30:19:67/00:00:1e:00:00/40 Emask 0x50 (ATA bus error)
ata3.00: status: { DRDY }
ata3.00: cmd 60/08:08:30:19:67/00:00:1e:00:00/40 tag 1 ncq 4096 in
         res 40/00:08:30:19:67/00:00:1e:00:00/40 Emask 0x50 (ATA bus error)

ata3.00: status: { DRDY }
ata3: hard resetting link
ata3: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
ata3.00: both IDENTIFYs aborted, assuming NODEV
ata3.00: revalidation failed (errno=-2)
ata3: hard resetting link
ata3: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
ata3.00: configured for UDMA/33
ata3: exception Emask 0x40 SAct 0x0 SErr 0x80800 action 0x7 t4
ata3: irq_stat 0x40000001
ata3: SError: { HostInt 10B8B }
ata3: hard resetting link
ata3: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
ata3.00: failed to IDENTIFY (I/O error, err_mask=0x100)
ata3.00: revalidation failed (errno=-5)
ata3: hard resetting link
ata3: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
ata3.00: failed to IDENTIFY (I/O error, err_mask=0x100)
ata3.00: revalidation failed (errno=-5)
ata3.00: limiting speed to UDMA/33:PIO3
ata3: hard resetting link
ata3: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
ata3.00: configured for UDMA/33
ata3: exception Emask 0x50 SAct 0x0 SErr 0x80800 action 0x7 t3
ata3: irq_stat 0x08000002, interface fatal error
ata3: SError: { HostInt 10B8B }
ata3: hard resetting link
ata3: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
ata3.00: configured for UDMA/33
sd 2:0:0:0: [sdc] Result: hostbyte=DID_OK driverbyte=DRIVER_SENSE,SUGGEST_OK sd 2:0:0:0: [sdc] Sense Key : Aborted Command [current] [descriptor] Descriptor sense data with sense descriptors (in hex):

        72 0b 00 00 00 00 00 0c 00 0a 80 00 00 00 00 00 
        1e 67 19 30

sd 2:0:0:0: [sdc] Add. Sense: No additional sense information
end_request: I/O error, dev sdc, sector 510073392
ata3: EH complete
sd 2:0:0:0: [sdc] 2930277168 512-byte hardware sectors (1500302 MB)
sd 2:0:0:0: [sdc] Write Protect is off
sd 2:0:0:0: [sdc] Mode Sense: 00 3a 00 00
sd 2:0:0:0: [sdc] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA sd 2:0:0:0: [sdc] 2930277168 512-byte hardware sectors (1500302 MB)
sd 2:0:0:0: [sdc] Write Protect is off
sd 2:0:0:0: [sdc] Mode Sense: 00 3a 00 00
sd 2:0:0:0: [sdc] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA ata3.00: exception Emask 0x50 SAct 0x1 SErr 0x280900 action 0x6 frozen ata3.00: irq_stat 0x08000000, interface fatal error
ata3: SError: { UnrecovData HostInt 10B8B BadCRC }
ata3.00: cmd 60/08:00:40:19:67/00:00:1e:00:00/40 tag 0 ncq 4096 in

         res 40/00:00:40:19:67/00:00:1e:00:00/40 Emask 0x50 (ATA bus error)

ata3.00: status: { DRDY }
ata3: hard resetting link
ata3: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
ata3.00: both IDENTIFYs aborted, assuming NODEV
ata3.00: revalidation failed (errno=-2)
ata3: hard resetting link
ata3: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
ata3.00: configured for UDMA/33
ata3: exception Emask 0x40 SAct 0x0 SErr 0x80800 action 0x7 t4
ata3: irq_stat 0x40000001
ata3: SError: { HostInt 10B8B }
ata3: hard resetting link
ata3: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
ata3.00: configured for UDMA/33
ata3: EH complete
sd 2:0:0:0: [sdc] 2930277168 512-byte hardware sectors (1500302 MB)
sd 2:0:0:0: [sdc] Write Protect is off
sd 2:0:0:0: [sdc] Mode Sense: 00 3a 00 00
sd 2:0:0:0: [sdc] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA sd 2:0:0:0: [sdc] 2930277168 512-byte hardware sectors (1500302 MB)
sd 2:0:0:0: [sdc] Write Protect is off
sd 2:0:0:0: [sdc] Mode Sense: 00 3a 00 00
sd 2:0:0:0: [sdc] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA ata3.00: exception Emask 0x50 SAct 0x1 SErr 0x280900 action 0x6 frozen ata3.00: irq_stat 0x08000000, interface fatal error
ata3: SError: { UnrecovData HostInt 10B8B BadCRC }
ata3.00: cmd 60/08:00:48:19:67/00:00:1e:00:00/40 tag 0 ncq 4096 in

         res 40/00:00:48:19:67/00:00:1e:00:00/40 Emask 0x50 (ATA bus error)

ata3.00: status: { DRDY }
ata3: hard resetting link
ata3: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
ata3.00: both IDENTIFYs aborted, assuming NODEV
ata3.00: revalidation failed (errno=-2)
ata3: hard resetting link
ata3: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
ata3.00: configured for UDMA/33
ata3: exception Emask 0x40 SAct 0x0 SErr 0x80800 action 0x7 t4
ata3: irq_stat 0x40000001
ata3: SError: { HostInt 10B8B }
ata3: hard resetting link
ata3: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
ata3.00: qc timeout (cmd 0xec)
ata3.00: failed to IDENTIFY (I/O error, err_mask=0x4)
ata3.00: revalidation failed (errno=-5)
ata3: hard resetting link
ata3: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
ata3.00: configured for UDMA/33
ata3: exception Emask 0x40 SAct 0x0 SErr 0x80800 action 0x7 t3
ata3: SError: { HostInt 10B8B }
ata3: hard resetting link
ata3: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
ata3.00: configured for UDMA/33
ata3: EH complete
sd 2:0:0:0: [sdc] 2930277168 512-byte hardware sectors (1500302 MB)
sd 2:0:0:0: [sdc] Write Protect is off
sd 2:0:0:0: [sdc] Mode Sense: 00 3a 00 00
sd 2:0:0:0: [sdc] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA sd 2:0:0:0: [sdc] 2930277168 512-byte hardware sectors (1500302 MB)
sd 2:0:0:0: [sdc] Write Protect is off
sd 2:0:0:0: [sdc] Mode Sense: 00 3a 00 00
sd 2:0:0:0: [sdc] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA ata3.00: exception Emask 0x50 SAct 0x1 SErr 0x280900 action 0x6 frozen ata3.00: irq_stat 0x08000000, interface fatal error
ata3: SError: { UnrecovData HostInt 10B8B BadCRC }
ata3.00: cmd 60/08:00:48:19:67/00:00:1e:00:00/40 tag 0 ncq 4096 in

         res 40/00:00:48:19:67/00:00:1e:00:00/40 Emask 0x50 (ATA bus error)

Soeren

Justin Piszcz

2008-12-02 09:49 UTC #1 lore raw

Quoted 13 lines · Soeren Sonnenburg

Dear all,
I just purchased a seagate 1.5TB drive ST31500341AS, with firmware revision CC1G (which according to seagate is not affected by the cache flush bug) and I am getting the errors below (after almost a day of uptime without problems). The drive is replacing a 750G variant from seagate with which I had months of uptime and no errors whatsoever.
I hope anyone has an idea?
- relevant part of hdparm -I and lspci
ATA device, with non-removable media

Quoted 8 lines

	Model Number:       ST31500341AS
	Firmware Revision:  CC1G
	Transport:          Serial
00:1f.2 SATA controller: Intel Corporation 82801JI (ICH10 Family) SATA AHCI Controller
- the error(tm)

A few items:

         res 40/00:00:48:19:67/00:00:1e:00:00/40 Emask 0x50 (ATA bus error)
         ata3: SError: { UnrecovData HostInt 10B8B BadCRC }

These are usually realted to a bad cable or connector.

ata3: SATA link up 1.5 Gbps (SStatus 113 SControl 310)

Did you remove the 1.5 Gbps jumper so it can run at 3.0 Gbps?

Justin.

Soeren Sonnenburg

author

2008-12-02 14:05 UTC #2 lore raw

Quoted 23 lines · Justin Piszcz

Quoted 20 lines · Soeren Sonnenburg
Dear all,
I just purchased a seagate 1.5TB drive ST31500341AS, with firmware revision CC1G (which according to seagate is not affected by the cache flush bug) and I am getting the errors below (after almost a day of uptime without problems). The drive is replacing a 750G variant from seagate with which I had months of uptime and no errors whatsoever.
I hope anyone has an idea?
- relevant part of hdparm -I and lspci
ATA device, with non-removable media
	Model Number:       ST31500341AS
	Firmware Revision:  CC1G
	Transport:          Serial
00:1f.2 SATA controller: Intel Corporation 82801JI (ICH10 Family) SATA AHCI Controller

Quoted 8 lines

Quoted 1 line
- the error(tm)
A few items:
          res 40/00:00:48:19:67/00:00:1e:00:00/40 Emask 0x50 (ATA bus error)
          ata3: SError: { UnrecovData HostInt 10B8B BadCRC }
These are usually realted to a bad cable or connector.

OK, if this happens again I will try a new cable. However, the backplane
(it is this one:
http://www.raidsonic.de/en/pages/products/backplanes.php?we_objectID=4251 ) was working nicely with another disk in the same slot (but maybe I did not perfectly insert the disk...)

Quoted 3 lines

ata3: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
Did you remove the 1.5 Gbps jumper so it can run at 3.0 Gbps?

Yes. This is actually the only difference to the drive before (which was 1.5 Gbps).

For now it is all running nicely and I did a full dd if= ... read of the disk:

ata3: SATA max UDMA/133 irq_stat 0x00400040, connection status changed irq 510
ata3: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
ata3.00: HPA detected: current 2930277168, native 18446744072344861488 ata3.00: ATA-8: ST31500341AS, CC1G, max UDMA/133
ata3.00: 2930277168 sectors, multi 0: LBA48 NCQ (depth 31/32) ata3.00: configured for UDMA/133

Thank you very much!!
Soeren

Tejun Heo

2008-12-03 03:00 UTC #3 lore raw

In reply to Soeren Sonnenburg

hello,

Quoted 15 lines · Soeren Sonnenburg

I just purchased a seagate 1.5TB drive ST31500341AS, with firmware revision CC1G (which according to seagate is not affected by the cache flush bug) and I am getting the errors below (after almost a day of uptime without problems). The drive is replacing a 750G variant from seagate with which I had months of uptime and no errors whatsoever.
I hope anyone has an idea?
- relevant part of hdparm -I and lspci
ATA device, with non-removable media
	Model Number:       ST31500341AS                            
	Firmware Revision:  CC1G    
	Transport:          Serial

Quoted 8 lines

00:1f.2 SATA controller: Intel Corporation 82801JI (ICH10 Family) SATA AHCI Controller
- the error(tm)
ata3.00: exception Emask 0x50 SAct 0x1 SErr 0x280900 action 0x6 frozen ata3.00: irq_stat 0x08000000, interface fatal error
ata3: SError: { UnrecovData HostInt 10B8B BadCRC }

Your machine seems to be suffering genuine link layer problem. In most cases, this indicates hardware problem and in my experience common causes are (in the order of ballpark frequency)...

1. inadequate power supply

2. device and controller don't like each other on 3Gbps

3. cable too long or flaky connector (especially w/ eSATA cables or genders or backplanes)

4. faulty controller or drive

Signature · 1 line

tejun

Soeren Sonnenburg

author

2008-12-04 07:49 UTC #4 lore raw

Quoted 1 line · Tejun Heo

hello,

Hi Tejun, Hi list,

[...]

Quoted 9 lines

Quoted 5 lines
- the error(tm)
ata3.00: exception Emask 0x50 SAct 0x1 SErr 0x280900 action 0x6 frozen ata3.00: irq_stat 0x08000000, interface fatal error
ata3: SError: { UnrecovData HostInt 10B8B BadCRC }
Your machine seems to be suffering genuine link layer problem. In most cases, this indicates hardware problem and in my experience common causes are (in the order of ballpark frequency)...

First of all thanks for your reply! Would be nice to have an FAQ with all the errors and the most common causes somewhere...

Quoted 1 line

1. inadequate power supply

this I would exclude (as I cannot trigger the problem by increasing load while writing to the 4 disks in the machine)

Quoted 1 line

2. device and controller don't like each other on 3Gbps

possible

Quoted 2 lines

3. cable too long or flaky connector (especially w/ eSATA cables or genders or backplanes)

might have been the problem in this case.

Quoted 1 line

4. faulty controller or drive

the controller should be OK as it was working with another drive.

But as the problem only appeared once and I did all kinds of tests in the last two days without this problem to re-appear I guess it must have been either:

a) hot plug attempt with first only having a 1.5Gps drive in the backplane
b) the connection was somehow flaky between drive and backplane (drive was not inserted properly - still strange that it took >8 hrs to trigger the problem).

I will keep an eye on it, but I don't expect the problem to re-appear - but having had bad experiences with all kinds of controller/disk setups and reading about the seagate firmware bug in earlier firmware revisions of this drive made me alert..

So sorry for the noise and thanks for the helpful response! Soeren