schizophrenic G5 ...
Hi,
I have a water cooled dual 2.5 GHz G5 (Powermac7,3). It has YDL 6.0 on
it. Using the stock YDL 2.6.23 kernel this machine "appears" to work fine.
After finally getting it to boot under 2.6.27, it will shut itself off
if put under any significant load. And it is doing it very quickly. Like within a few seconds of becoming busy. I just discovered it is spitting out messages about "temperature way above maximum" (from therm_pm72.c).
This one has the Panasonic cooling system. I have checked behind the
cover and see no evidence of leaks.
When put under load under the stock YDL kernel, the cpu fans will speed
up for about 2 minutes. Then over the next minute or so they will slow down almost to idle. Thereafter a whirring sound can be heard every 15 to 30 seconds lasting about 5 seconds. Which I am guessing is the pump? The exhaust air barely gets warm?
Anyone have any ideas? Could the cooling system NOT be correctly
thermally connected to the cpus?
kevin
Quoted 13 lines · Kevin Diggs
Hi,
I have a water cooled dual 2.5 GHz G5 (Powermac7,3). It has YDL 6.0 on
it. Using the stock YDL 2.6.23 kernel this machine "appears" to work fine.After finally getting it to boot under 2.6.27, it will shut itself off
if put under any significant load. And it is doing it very quickly. Like within a few seconds of becoming busy. I just discovered it is spitting out messages about "temperature way above maximum" (fromtherm_pm72.c).This one has the Panasonic cooling system. I have checked behind the
cover and see no evidence of leaks.
Quoted 8 lines
When put under load under the stock YDL kernel, the cpu fans will speed
up for about 2 minutes. Then over the next minute or so they will slow down almost to idle. Thereafter a whirring sound can be heard every 15 to 30 seconds lasting about 5 seconds. Which I am guessing is the pump? The exhaust air barely gets warm?Anyone have any ideas? Could the cooling system NOT be correctly
thermally connected to the cpus?
I have approx. the same here taking dust under the desk, I'll give it a spin but i might have to wait a couple of days...
If mine works, then we'll have to run some more intensive debugging to see what's going on.
Cheers,
Ben.
Quoted 10 lines · Benjamin Herrenschmidt
Quoted 8 lines · Kevin Diggs
Hi,
I have a water cooled dual 2.5 GHz G5 (Powermac7,3). It has YDL 6.0 on
it. Using the stock YDL 2.6.23 kernel this machine "appears" to work fine.After finally getting it to boot under 2.6.27, it will shut itself off
if put under any significant load. And it is doing it very quickly. Like within a few seconds of becoming busy. I just discovered it is spitting out messages about "temperature way above maximum" (fromtherm_pm72.c).
Quoted 9 lines
Quoted 8 lines
This one has the Panasonic cooling system. I have checked behind the
cover and see no evidence of leaks.When put under load under the stock YDL kernel, the cpu fans will speed
up for about 2 minutes. Then over the next minute or so they will slow down almost to idle. Thereafter a whirring sound can be heard every 15 to 30 seconds lasting about 5 seconds. Which I am guessing is the pump? The exhaust air barely gets warm?Anyone have any ideas? Could the cooling system NOT be correctly
thermally connected to the cpus?
I would appreciate it if one of the many people on this list that are way more smarterer than me could tell me something like, "If this were true you would have toasted the cpus already!"
Quoted 11 lines
I have approx. the same here taking dust under the desk, I'll give it a spin but i might have to wait a couple of days...
If mine works, then we'll have to run some more intensive debugging to see what's going on.
Cheers,
Ben.
Ben,
I would appreciate it. I am now kinda afraid to turn the thing on.
Quoted 6 lines · On Sun, 21 Dec 2008 16:11:43 -0800 Kevin Diggs <[email protected]> wrote:
Hi,
I have a water cooled dual 2.5 GHz G5 (Powermac7,3). It has
YDL 6.0 on it. Using the stock YDL 2.6.23 kernel this machine "appears" to work fine.
Quoted 6 lines
After finally getting it to boot under 2.6.27, it will shut
itself off if put under any significant load. And it is doing it very quickly. Like within a few seconds of becoming busy. I just discovered it is spitting out messages about "temperature way above maximum" (fromtherm_pm72.c).
I have a very similar problem on my mac at work.
I don't know atm how to look up the critical temperature that is fused. My mac reported only 55 degrees for the one cpu.
The critical temperature can be read from the device-tree if i remember it correctly.
I heard that there exists a bootable CD which contains a tool to refuse the CPU. Dont know where to download it, so my pragmatic solution was to relocate the machine to a room with air conditioning ;-)
And I also run the ONE cpu at lowest frequency.
ck
Signature · 2 lines
Hi, I am a signature virus. Please copy me into your ~/.signature to help me spread.
Quoted 10 lines
I have a very similar problem on my mac at work.
I don't know atm how to look up the critical temperature that is fused. My mac reported only 55 degrees for the one cpu.
The critical temperature can be read from the device-tree if i remember it correctly.
I heard that there exists a bootable CD which contains a tool to refuse the CPU. Dont know where to download it, so my pragmatic solution was to relocate the machine to a room with air conditioning ;-)
And I also run the ONE cpu at lowest frequency.
The calibration info is in an i2c EEPROM iirc, though we read it's content via the device-tree.
Cheers,
Ben.
Quoted 28 lines · Christian Krafft
Quoted 6 lines · On Sun, 21 Dec 2008 16:11:43 -0800 Kevin Diggs <[email protected]> wrote:
Hi,
I have a water cooled dual 2.5 GHz G5 (Powermac7,3). It has
YDL 6.0 on it. Using the stock YDL 2.6.23 kernel this machine "appears" to work fine.Quoted 6 lines
After finally getting it to boot under 2.6.27, it will shut
itself off if put under any significant load. And it is doing it very quickly. Like within a few seconds of becoming busy. I just discovered it is spitting out messages about "temperature way above maximum" (fromtherm_pm72.c).I have a very similar problem on my mac at work.
I don't know atm how to look up the critical temperature that is fused. My mac reported only 55 degrees for the one cpu.
The critical temperature can be read from the device-tree if i remember it correctly.
I heard that there exists a bootable CD which contains a tool to refuse the CPU. Dont know where to download it, so my pragmatic solution was to relocate the machine to a room with air conditioning ;-)
And I also run the ONE cpu at lowest frequency.
Quoted 2 lines
ck
Critical temperature? If it is in the device tree are we sure it isn't (from the 970fx_thermal_diode_an, page 2, second paragraph):
In the PowerPC970FX family, the thermal diode is calibrated at a specified calibration temperature, usually around 70C, with no power on the chip, VDD = 0.0V, and 100 micro-amps being driven through the diode. The voltage across the diode is measured; it should be between 0.60V and 0.80V. The measured voltage and temperature is stored in Thermal Diode Calibration fuse bits. A second lower temperature value is used to set the second calibration point, refer to the datasheet for this value.
On page 3 it also has:
Reading Thermal Diode Calibration Data Via JTAG
In order to access the Thermal Diode Calibration data stored in each processor, a sequence of JTAG commands must be issued, usually over the IIC bus. By using JTAG commands, the desired data will appear serially on the PowerPC970FX TDO pin or can be read using IIC. The detailed information on how to perform the read operation of the calibration registers is found in the PowerPC970FX User s Manual. Reading the thermal diode calibration register should be a one-time-only procedure. It is assumed that the Thermal Diode Calibration data stored in each processor will be captured and stored in system ROM for subsequent use.
kevin
Quoted 5 lines · Kevin Diggs
Hi,
I have a water cooled dual 2.5 GHz G5 (Powermac7,3). It has YDL 6.0
on it. Using the stock YDL 2.6.23 kernel this machine "appears" to work fine.
Quoted 10 lines
After finally getting it to boot under 2.6.27, it will shut itself
off if put under any significant load. And it is doing it very quickly. Like within a few seconds of becoming busy. I just discovered it is spitting out messages about "temperature way above maximum" (fromtherm_pm72.c).This one has the Panasonic cooling system. I have checked behind the
cover and see no evidence of leaks.When put under load under the stock YDL kernel, the cpu fans will
speed up for about 2 minutes. Then over the next minute or so they will slow down almost to idle. Thereafter a whirring sound can be heard every 15 to 30 seconds lasting about 5 seconds. Which I am guessing is the pump? The exhaust air barely gets warm?
If I run:
while true; do
echo -n "cpu0\: "; cat cpu0_temperature; echo -ne "\t"; cat cpu0_current; echo ""; echo -n "cpu1\: "; cat cpu1_temperature; echo -ne "\t"; cat cpu1_current; echo ""; sleep 1;
done
in one window and:
time /home/kevdig//r-970 -b4 -s1|nice -19 bzip2 -9v|dd bs=4b count=400000 of=/dev/null
in two others I see different results between 2.6.23 and 2.6.27. Under the stock YDL 6.0 2.6.23 kernel, the temperatures level off at 50 and 70. Peak temps are about 56 and 76. Idle temps are about 46 and 54.
Under 2.6.27, if I run ONE I see cpu1 temps range from 74 -> 89 -> 105
-> 111 -> 86. All one second apart. This happened pretty fast. Once I saw the 111 I ^c'ed the process. Can the temp really change that fast?
kevin