MIPS: Add VCT board series support (Part 2/3)
PATCH v3 2/3 MIPS: Add VCT board series support (Part 2/3)
Signed-off-by Stefan Roese <[email protected]>
---
v3:
- Added USB EHCI support
- Added performance enhanced OneNAND read support
v2:
- Fixed issues in u-boot.lds mentioned by Andrew Dyer
board/micronas/vct/ehci.c | 110 +++++++ board/micronas/vct/gpio.c | 88 +++++ board/micronas/vct/scc.c | 669 +++++++++++++++++++++++++++++++++++++++ board/micronas/vct/scc.h | 205 ++++++++++++ board/micronas/vct/smc_eeprom.c | 394 +++++++++++++++++++++++ board/micronas/vct/top.c | 289 +++++++++++++++++ board/micronas/vct/u-boot.lds | 71 ++++ board/micronas/vct/vct.c | 117 +++++++ board/micronas/vct/vct.h | 104 ++++++ include/configs/vct.h | 340 ++++++++++++++++++++ 10 files changed, 2387 insertions(+), 0 deletions(-) create mode 100644 board/micronas/vct/ehci.c create mode 100644 board/micronas/vct/gpio.c create mode 100644 board/micronas/vct/scc.c create mode 100644 board/micronas/vct/scc.h create mode 100644 board/micronas/vct/smc_eeprom.c create mode 100644 board/micronas/vct/top.c create mode 100644 board/micronas/vct/u-boot.lds create mode 100644 board/micronas/vct/vct.c create mode 100644 board/micronas/vct/vct.h create mode 100644 include/configs/vct.h
board/micronas/vct/ehci.c new file +110 -0
@@ -0,0 +1,110 @@ +/* +* (C) Copyright 2009 Stefan Roese <[email protected]>, DENX Software Engineering +* +* Original Author Guenter Gebhardt +* Copyright (C) 2006 Micronas GmbH +* +* This program is free software; you can redistribute it and/or +* modify it under the terms of the GNU General Public License as +* published by the Free Software Foundation; either version 2 of +* the License, or (at your option) any later version. +* +* This program is distributed in the hope that it will be useful, +* but WITHOUT ANY WARRANTY; without even the implied warranty of +* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the +* GNU General Public License for more details. +* +* You should have received a copy of the GNU General Public License +* along with this program; if not, write to the Free Software +* Foundation, Inc., 59 Temple Place, Suite 330, Boston, +* MA 02111-1307 USA +*/ + +#include <common.h> + +#include "vct.h" + +int vct_ehci_hcd_init (u32 *hccr,u32 *hcor) +{ +int retval; +u32 val; +u32 addr; + +dcgu_set_reset_switch (DCGU_HW_MODULE_USB_24 ,DCGU_SWITCH_ON ); +dcgu_set_reset_switch (DCGU_HW_MODULE_USB_60 ,DCGU_SWITCH_ON ); +dcgu_set_clk_switch (DCGU_HW_MODULE_USB_24 ,DCGU_SWITCH_ON ); +dcgu_set_clk_switch (DCGU_HW_MODULE_USB_PLL ,DCGU_SWITCH_ON ); +dcgu_set_reset_switch (DCGU_HW_MODULE_USB_24 ,DCGU_SWITCH_OFF ); + +/* Wait until (DCGU_USBPHY_STAT == 7) */ + addr =DCGU_USBPHY_STAT (DCGU_BASE ); + val =reg_read (addr); +while (val !=7 ) + val =reg_read (addr); + +dcgu_set_clk_switch (DCGU_HW_MODULE_USB_60 ,DCGU_SWITCH_ON ); +dcgu_set_reset_switch (DCGU_HW_MODULE_USB_60 ,DCGU_SWITCH_OFF ); + + retval =scc_reset (SCC_USB_RW ,0 ); +if (retval) { +printf ("scc_reset(SCC_USB_RW, 0) returned: 0x%x\n" , retval); +return retval; + }else { + retval =scc_reset (SCC_CPU1_SPDMA_RW ,0 ); +if (retval) { +printf ("scc_reset(SCC_CPU1_SPDMA_RW, 0) returned: 0x%x\n" , + retval); +return retval; + } + } + +if (!retval) { +/* +* For the AGU bypass, where the SCC client provides full +* physical address +*/ +scc_set_usb_address_generation_mode (1 ); +scc_setup_dma (SCC_USB_RW ,BCU_USB_BUFFER_1 ,DMA_LINEAR , +USE_NO_FH ,DMA_READ ,0 ); +scc_setup_dma (SCC_CPU1_SPDMA_RW ,BCU_USB_BUFFER_1 ,DMA_LINEAR , +USE_NO_FH ,DMA_WRITE ,0 ); +scc_setup_dma (SCC_USB_RW ,BCU_USB_BUFFER_0 ,DMA_LINEAR , +USE_NO_FH ,DMA_WRITE ,0 ); +scc_setup_dma (SCC_CPU1_SPDMA_RW ,BCU_USB_BUFFER_0 ,DMA_LINEAR , +USE_NO_FH ,DMA_READ ,0 ); + +/* Enable memory interface */ +scc_enable (SCC_USB_RW ,1 ); + +/* Start (start_cmd=0) DMAs */ +scc_dma_cmd (SCC_USB_RW ,DMA_START ,0 ,DMA_READ ); +scc_dma_cmd (SCC_USB_RW ,DMA_START ,0 ,DMA_WRITE ); + }else { +printf ("Cannot configure USB memory channel.\n" ); +printf ("USB can not access RAM. SCC configuration failed.\n" ); +return retval; + } + +/* Wait a short while */ +udelay (300000 ); + +reg_write (USBH_BURSTSIZE (USBH_BASE ),0x00001c1c ); + +/* Set EHCI structures and DATA in RAM */ +reg_write (USBH_USBHMISC (USBH_BASE ),0x00840003 ); +/* Set USBMODE to bigendian and set host mode */ +reg_write (USBH_USBMODE (USBH_BASE ),0x00000007 ); + +/* +* USBH_BURSTSIZE MUST EQUAL 0x00001c1c in order for +* 512 byte USB transfers on the bulk pipe to work properly. +* Set USBH_BURSTSIZE to 0x00001c1c +*/ +reg_write (USBH_BURSTSIZE (USBH_BASE ),0x00001c1c ); + +/* Insert access register addresses */ + *hccr =REG_GLOBAL_START_ADDR +USBH_CAPLENGTH (USBH_BASE ); + *hcor =REG_GLOBAL_START_ADDR +USBH_USBCMD (USBH_BASE ); + +return 0 ; +}
board/micronas/vct/gpio.c new file +88 -0
88 lines not on this page · raw message
board/micronas/vct/scc.c new file +669 -0
669 lines not on this page · raw message
board/micronas/vct/scc.h new file +205 -0
205 lines not on this page · raw message
board/micronas/vct/smc_eeprom.c new file +394 -0
394 lines not on this page · raw message
board/micronas/vct/top.c new file +289 -0
289 lines not on this page · raw message
board/micronas/vct/u-boot.lds new file +71 -0
71 lines not on this page · raw message
board/micronas/vct/vct.c new file +117 -0
117 lines not on this page · raw message
board/micronas/vct/vct.h new file +104 -0
104 lines not on this page · raw message
include/configs/vct.h new file +340 -0
340 lines not on this page · raw message
Signature · 1 line
1.6.1