Skip to contentSkip to conversation

Pinnacle dual Hybrid pro PCI-express - linuxTV!

linux-dvb CityK 8 participants 16 messages Jan 14, 2009 – Jul 6, 2009 1 message not in the archive Media (V4L/DVB)

lore
Share & tools
lore

A message that is not in the archive (sent off-list or not yet received): [email protected]

CityK

author
#1 lore raw
Quoted 4 lines · Catimimi

Hi,

As I didn't yet subscribe to the list, I reply directly to your discussion with Romain

sorry, I don't recall it offhand.

Quoted 60 lines

in ordezr to send you the result of :

lspci -vvxxx

for the Pinnacle PCTV Dual Hybrid Pro PCI Express (3010i)

______________________

04:00.0 Multimedia controller: Philips Semiconductors Device 7162
Subsystem: Pinnacle Systems Inc. Device 0100
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 16 bytes
Interrupt: pin A routed to IRQ 5
Region 0: Memory at dde00000 (64-bit, non-prefetchable) [size=1M]
Capabilities: [40] Message Signalled Interrupts: Mask- 64bit+
Queue=0/5 Enable-
Address: 0000000000000000 Data: 0000
Capabilities: [50] Express (v1) Endpoint, MSI 00
DevCap: MaxPayload 128 bytes, PhantFunc 0, Latency L0s
<256ns, L1 <1us
ExtTag- AttnBtn- AttnInd- PwrInd- RBE- FLReset-
DevCtl: Report errors: Correctable- Non-Fatal- Fatal-
Unsupported-
RlxdOrd+ ExtTag- PhantFunc- AuxPwr- NoSnoop- MaxPayload 128 bytes, MaxReadReq 128 bytes
DevSta: CorrErr- UncorrErr+ FatalErr- UnsuppReq+ AuxPwr-
TransPend-

                LnkCap: Port #1, Speed 2.5GT/s, Width x1, ASPM L0s L1,

Latency L0 <4us, L1 <64us
ClockPM- Suprise- LLActRep- BwNot-
LnkCtl: ASPM Disabled; RCB 128 bytes Disabled- Retrain-
CommClk-
ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
LnkSta: Speed 2.5GT/s, Width x1, TrErr- Train- SlotClk-
DLActive- BWMgmt- ABWMgmt-
Capabilities: [74] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA
PME(D0+,D1+,D2+,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [80] Vendor Specific Information <?>
00: 31 11 62 71 07 00 10 00 00 00 80 04 04 00 00 00
10: 04 00 e0 dd 00 00 00 00 00 00 00 00 00 00 00 00
20: 00 00 00 00 00 00 00 00 00 00 00 00 bd 11 00 01
30: 00 00 00 00 40 00 00 00 00 00 00 00 05 01 00 00
40: 05 50 8a 00 00 00 00 00 00 00 00 00 00 00 00 00
50: 10 74 01 00 80 00 28 00 10 00 0a 00 11 6c 03 01
60: 08 00 11 00 00 0a 00 00 00 00 00 00 00 00 00 00
70: 00 00 00 00 01 80 02 3e 00 00 00 00 00 00 00 00
80: 09 00 50 00 03 0c 00 00 02 02 00 00 00 00 00 00
90: 00 04 00 00 00 00 00 08 00 00 10 00 00 00 00 00
a0: 01 00 00 04 03 18 00 00 00 00 01 04 00 00 00 00
b0: 00 00 00 00 00 00 00 00 00 00 00 20 01 2a 00 00
c0: 01 00 00 00 00 00 00 00 01 00 00 00 00 00 00 00
d0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
e0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
f0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00

Quoted 1 line

I hope it'll help.

Could you put it in the wiki if its not already contained there. Thanks.

Quoted 5 lines

I tried the driver found here : http://jusst.de/hg/saa716x
It compiles and install, but if I try : modprobe saa716x_hybrid.ko I get a fatal error : module not found.

I can't find any message in dmesg.

try without the ".ko", i.e. instead, use:

modprobe saa716x_hybrid

Quoted 2 lines

Ready for further trials.
Michel.

#3 lore raw
Quoted 5 lines · Catimimi

try without the ".ko", i.e. instead, use:

modprobe saa716x_hybrid

OK, shame on me, it works but nothing happens.

Of course ;-) The PCI ID of the card is not listed. I happen to have the same card, you can add the ID to the list but note that the frontend is not there yet... so the module will load, will print some something... and that's it.
I have a couple of patches queued and I plan to do some experimentation in the weekend though ;)

Luca

#5 lore raw
Quoted 7 lines · Catimimi
Quoted 4 lines · Luca Tettamanti

Of course ;-) The PCI ID of the card is not listed. I happen to have the same card, you can add the ID to the list but note that the frontend is not there yet... so the module will load, will print some something... and that's it.

I did that too but without success. I also loaded the frontend modules.

Sorry, I meat that the correct frontend (TDA10046A) is not compiled by default.

Quoted 4 lines
Quoted 2 lines

I have a couple of patches queued and I plan to do some experimentation in the weekend though ;)

OK, If I can help, tell me.

Only minor fixes, I'm still trying to understand the code ;-) Manu Abraham is doing the hard work...

L

#6 lore raw
In reply to Luca Tettamanti

Hi,

I also own a pair of Pinnacle 3010ix.

Luca, where should the PCI ID go? I can't believe that adding a new card to the supported card list is just that simple. Do you know a web page with information about it?.

Thanks

-----Mensaje original-----
De: [email protected] [mailto:[email protected]] En nombre de Luca Tettamanti
Enviado el: jueves, 15 de enero de 2009 16:44
Para: Catimimi
CC: [email protected]; Linux-media
Asunto: Re: [linux-dvb] Pinnacle dual Hybrid pro PCI-express - linuxTV!

Quoted 5 lines · Catimimi

try without the ".ko", i.e. instead, use:

modprobe saa716x_hybrid

OK, shame on me, it works but nothing happens.

Of course ;-) The PCI ID of the card is not listed. I happen to have the same card, you can add the ID to the list but note that the frontend is not there yet... so the module will load, will print some something... and that's it.
I have a couple of patches queued and I plan to do some experimentation in the weekend though ;)

Luca

_______________________________________________
linux-dvb users mailing list
For V4L/DVB development, please use instead [email protected] [email protected]
http://www.linuxtv.org/cgi-bin/mailman/listinfo/linux-dvb

#7 lore raw

Hi,

Is this thread saying that the Pinnacle 3010i is now supported under linux? if so does this go for the Pinnacle 7010i too?

Thanks,

Matt

2009/3/27 dCrypt <[email protected]>:

Quoted 47 lines

Hi,

I also own a pair of Pinnacle 3010ix.

Luca, where should the PCI ID go? I can't believe that adding a new card to the supported card list is just that simple. Do you know a web page with information about it?.

Thanks

-----Mensaje original-----
De: [email protected] [mailto:[email protected]] En nombre de Luca Tettamanti
Enviado el: jueves, 15 de enero de 2009 16:44
Para: Catimimi
CC: [email protected]; Linux-media
Asunto: Re: [linux-dvb] Pinnacle dual Hybrid pro PCI-express - linuxTV!

Quoted 5 lines · Catimimi

try without the ".ko", i.e. instead, use:

modprobe saa716x_hybrid

OK, shame on me, it works but nothing happens.

Of course ;-) The PCI ID of the card is not listed. I happen to have the same card, you can add the ID to the list but note that the frontend is not there yet... so the module will load, will print some something... and that's it.
I have a couple of patches queued and I plan to do some experimentation in the weekend though ;)

Luca

_______________________________________________
linux-dvb users mailing list
For V4L/DVB development, please use instead [email protected] [email protected]
http://www.linuxtv.org/cgi-bin/mailman/listinfo/linux-dvb

_______________________________________________
linux-dvb users mailing list
For V4L/DVB development, please use instead [email protected] [email protected]
http://www.linuxtv.org/cgi-bin/mailman/listinfo/linux-dvb

#8 lore raw

Hi,

Is this thread saying that the Pinnacle 3010i is now supported under linux? if so does this go for the Pinnacle 7010i too?

Thanks,

Matt

2009/3/27 dCrypt <[email protected]>:

Quoted 47 lines

Hi,

I also own a pair of Pinnacle 3010ix.

Luca, where should the PCI ID go? I can't believe that adding a new card to the supported card list is just that simple. Do you know a web page with information about it?.

Thanks

-----Mensaje original-----
De: [email protected] [mailto:[email protected]] En nombre de Luca Tettamanti
Enviado el: jueves, 15 de enero de 2009 16:44
Para: Catimimi
CC: [email protected]; Linux-media
Asunto: Re: [linux-dvb] Pinnacle dual Hybrid pro PCI-express - linuxTV!

Quoted 5 lines · Catimimi

try without the ".ko", i.e. instead, use:

modprobe saa716x_hybrid

OK, shame on me, it works but nothing happens.

Of course ;-) The PCI ID of the card is not listed. I happen to have the same card, you can add the ID to the list but note that the frontend is not there yet... so the module will load, will print some something... and that's it.
I have a couple of patches queued and I plan to do some experimentation in the weekend though ;)

Luca

_______________________________________________
linux-dvb users mailing list
For V4L/DVB development, please use instead [email protected] [email protected]
http://www.linuxtv.org/cgi-bin/mailman/listinfo/linux-dvb

_______________________________________________
linux-dvb users mailing list
For V4L/DVB development, please use instead [email protected] [email protected]
http://www.linuxtv.org/cgi-bin/mailman/listinfo/linux-dvb

author
#9 lore raw
In reply to Catimimi
Quoted 4 lines · Catimimi
Quoted 2 lines · CityK

Could you put it in the wiki if its not already contained there. Thanks.

It was done yesterday.

Yep, saw that about 10 minutes later after I responded to this message :P . Thanks.

#10 lore raw

[linux-dvb] SAA716x

In reply to CityK

Hi all,

I'm trying to add my Pinnacle 3010i to the driver found here : http://jusst.de/hg/saa716x
I already got some preliminary results but in order to understand what I'm doing it would be great to get the result of "lspci -vvxxx" for at least one of the supported cards :

- Twinhan/Azurewave VP-6090
- Avermedia HC82
- Avermedia H788

I didn't find this test in the WIKI, so thanks in advance for posting this information. Michel.

#11 lore raw

Re: [linux-dvb] SAA716x

Quoted 9 lines · Catimimi

Hi all,

I'm trying to add my Pinnacle 3010i to the driver found here :
http://jusst.de/hg/saa716x
I already got some preliminary results but in order to understand what I'm doing it would be
great to get the result of "lspci -vvxxx" for at least one of the supported cards :

Quoted 3 lines

- Twinhan/Azurewave VP-6090
- Avermedia HC82
- Avermedia H788

They are not completely working yet. Currently some parts of the chip is working, but no stream yet. Can you please post some pictures of your card ?

Regards,
Manu

#12 lore raw

Re: [linux-dvb] SAA716x

Quoted 7 lines · Manu Abraham

Can you please post some
pictures of your card ?

Regards,
Manu

Hi,

You can find two high resolution pictures here :

http://catimimi.free.fr/Pinnacle/

I think that they are too heavy for the wiki.
I'm willing to help in any test with this Pinnacle 3010i card.

Regards.
Michel.

#13 lore raw

[linux-dvb] SAA716x

In reply to CityK

Hi all,

I'm trying to add my Pinnacle 3010i to the driver found here :
http://jusst.de/hg/saa716x
I already got some preliminary results but in order to understand what I'm doing it would be
great to get the result of "lspci -vvxxx" for at least one of the supported cards :

- Twinhan/Azurewave VP-6090
- Avermedia HC82
- Avermedia H788

I didn't find this test in the WIKI, so thanks in advance for posting this information.
Michel.

_______________________________________________
linux-dvb users mailing list
For V4L/DVB development, please use instead [email protected] [email protected]
http://www.linuxtv.org/cgi-bin/mailman/listinfo/linux-dvb

#14 lore raw

Re: [linux-dvb] SAA716x

VP6090 output from lspci -vvv and lspci -vvvn is here:

http://www.interlink.com.au/rad/quattros/

Quoted 28 lines · Catimimi

Hi all,

I'm trying to add my Pinnacle 3010i to the driver found here :
http://jusst.de/hg/saa716x
I already got some preliminary results but in order to understand what I'm doing it would be
great to get the result of "lspci -vvxxx" for at least one of the supported cards :

- Twinhan/Azurewave VP-6090
- Avermedia HC82
- Avermedia H788

I didn't find this test in the WIKI, so thanks in advance for posting this information.
Michel.

_______________________________________________
linux-dvb users mailing list
For V4L/DVB development, please use instead [email protected] [email protected]
http://www.linuxtv.org/cgi-bin/mailman/listinfo/linux-dvb

#15 lore raw

Re: [linux-dvb] SAA716x

Many thanks for the link, but it concerns device 1822:0037 and the supported device is 1822:0027 Anyway, I think that it can help.

Michel.

Quoted 41 lines · Konstantin Dimitrov

VP6090 output from lspci -vvv and lspci -vvvn is here:

http://www.interlink.com.au/rad/quattros/

Quoted 22 lines · Catimimi

Hi all,

I'm trying to add my Pinnacle 3010i to the driver found here :
http://jusst.de/hg/saa716x
I already got some preliminary results but in order to understand what I'm doing it would be
great to get the result of "lspci -vvxxx" for at least one of the supported cards :

- Twinhan/Azurewave VP-6090
- Avermedia HC82
- Avermedia H788

I didn't find this test in the WIKI, so thanks in advance for posting this information.
Michel.

Quoted 7 lines

_______________________________________________
linux-dvb users mailing list
For V4L/DVB development, please use instead [email protected] [email protected]
http://www.linuxtv.org/cgi-bin/mailman/listinfo/linux-dvb

--
To unsubscribe from this list: send the line "unsubscribe linux-media" in the body of a message to [email protected]
More majordomo info at http://vger.kernel.org/majordomo-info.html

#16 lore raw

Re: [linux-dvb] SAA716x

In reply to Konstantin Dimitrov

Am Mittwoch, den 21.01.2009, 12:43 +0200 schrieb Konstantin Dimitrov:

Quoted 34 lines

VP6090 output from lspci -vvv and lspci -vvvn is here:

http://www.interlink.com.au/rad/quattros/

Quoted 22 lines · Catimimi

Hi all,

I'm trying to add my Pinnacle 3010i to the driver found here :
http://jusst.de/hg/saa716x
I already got some preliminary results but in order to understand what I'm doing it would be
great to get the result of "lspci -vvxxx" for at least one of the supported cards :

- Twinhan/Azurewave VP-6090
- Avermedia HC82
- Avermedia H788

I didn't find this test in the WIKI, so thanks in advance for posting this information.
Michel.

Quoted 6 lines

_______________________________________________
linux-dvb users mailing list
For V4L/DVB development, please use instead [email protected] [email protected]
http://www.linuxtv.org/cgi-bin/mailman/listinfo/linux-dvb

Quoted 5 lines

_______________________________________________
linux-dvb users mailing list
For V4L/DVB development, please use instead [email protected] [email protected]
http://www.linuxtv.org/cgi-bin/mailman/listinfo/linux-dvb

hi,
unfortunately at last for me and some other guys the HC82 is not working with the 716x driver. but you can find my lspci output at:
http://www.linuxtv.org/wiki/index.php/AVerMedia_AVerTV_Hybrid_NanoExpress_(HC82)
martin