ACPI battery driver emits POWER_SUPPLY_STATUS_FULL when power lead plugged in
When I insert the power lead or attach my T61 to the powered dock, the battery power supply status goes like this:
0.00s Discharging
{dock}
0.10s Fully charged
1.00s Charging
This causes userspace (in my case gnome-power-manager) to pop up a dialog telling me the battery is full, and the icon flickers to fully green, then 10% green and charging.
This seems to have existed as long as the power supply class was being used by the acpi battery, but we've always relied on a userspace fudge.
This is tested with 2.6.27.9-159.fc10.i686, although I seem to get the same thing with git from kernel.org.
Is this a known issue? Does anybody have any insight into what causes this? I'm fully willing to test patches or debug this further myself.
Thanks,
Richard.
Hi Richard,
This is probably related to this piece of code (drivers/acpi/battery.c), similar code exists in drivers/acpi/sbs.c, but it is not relevant to your case:
case POWER_SUPPLY_PROP_STATUS: if (battery->state & 0x01) val->intval = POWER_SUPPLY_STATUS_DISCHARGING; else if (battery->state & 0x02) val->intval = POWER_SUPPLY_STATUS_CHARGING; else if (battery->state == 0) val->intval = POWER_SUPPLY_STATUS_FULL; else val->intval = POWER_SUPPLY_STATUS_UNKNOWN; break;
Actually, state==0 means POWER_SUPPLY_STATUS_NOT_CHARGING, so if that is preferred it could be changed.
Regards,
Alex.
Quoted 26 lines · Richard Hughes
When I insert the power lead or attach my T61 to the powered dock, the battery power supply status goes like this:
0.00s Discharging
{dock}
0.10s Fully charged
1.00s ChargingThis causes userspace (in my case gnome-power-manager) to pop up a dialog telling me the battery is full, and the icon flickers to fully green, then 10% green and charging.
This seems to have existed as long as the power supply class was being used by the acpi battery, but we've always relied on a userspace fudge.
This is tested with 2.6.27.9-159.fc10.i686, although I seem to get the same thing with git from kernel.org.
Is this a known issue? Does anybody have any insight into what causes this? I'm fully willing to test patches or debug this further myself.
Thanks,
Richard.
Quoted 13 lines · Alexey Starikovskiy
This is probably related to this piece of code (
drivers/acpi/battery.c), similar code exists indrivers/acpi/sbs.c, but it is not relevant to your case:case POWER_SUPPLY_PROP_STATUS: if (battery->state & 0x01) val->intval = POWER_SUPPLY_STATUS_DISCHARGING; else if (battery->state & 0x02) val->intval = POWER_SUPPLY_STATUS_CHARGING; else if (battery->state == 0) val->intval = POWER_SUPPLY_STATUS_FULL; else val->intval = POWER_SUPPLY_STATUS_UNKNOWN; break;
Quoted 1 line
Actually, state==0 means
POWER_SUPPLY_STATUS_NOT_CHARGING, so if that is preferred it could be changed.
It should be fixed, yes. Batteries being idle without being full are really common in laptops with battery-life-saving functions (charge/stop-charge threshold control).
Signature · 4 lines
"One disk to rule them all, One disk to find them. One disk to bring them all and in the darkness grind them. In the Land of Redmond where the shadows lie." -- The Silicon Valley Tarot Henrique Holschuh
Quoted 14 lines · Henrique de Moraes Holschuh
Quoted 13 lines · Alexey Starikovskiy
This is probably related to this piece of code (
drivers/acpi/battery.c), similar code exists indrivers/acpi/sbs.c, but it is not relevant to your case:case POWER_SUPPLY_PROP_STATUS: if (battery->state & 0x01) val->intval = POWER_SUPPLY_STATUS_DISCHARGING; else if (battery->state & 0x02) val->intval = POWER_SUPPLY_STATUS_CHARGING; else if (battery->state == 0) val->intval = POWER_SUPPLY_STATUS_FULL; else val->intval = POWER_SUPPLY_STATUS_UNKNOWN; break;
Quoted 5 lines
Quoted 1 line
Actually, state==0 means
POWER_SUPPLY_STATUS_NOT_CHARGING, so if that is preferred it could be changed.It should be fixed, yes. Batteries being idle without being full are really common in laptops with battery-life-saving functions (charge/stop-charge threshold control).
I suspected this might be the case. Is there a way we can get true battery state out of acpi for the battery? I always thought there could be two booleans: charging and discharging.
I guess fully charged isn't just !charging and !discharging.
Richard.
Quoted 20 lines · Richard Hughes
Quoted 14 lines · Henrique de Moraes Holschuh
Quoted 13 lines · Alexey Starikovskiy
This is probably related to this piece of code (
drivers/acpi/battery.c), similar code exists indrivers/acpi/sbs.c, but it is not relevant to your case:case POWER_SUPPLY_PROP_STATUS: if (battery->state & 0x01) val->intval = POWER_SUPPLY_STATUS_DISCHARGING; else if (battery->state & 0x02) val->intval = POWER_SUPPLY_STATUS_CHARGING; else if (battery->state == 0) val->intval = POWER_SUPPLY_STATUS_FULL; else val->intval = POWER_SUPPLY_STATUS_UNKNOWN; break;Quoted 4 lines
Quoted 1 line
Actually, state==0 means
POWER_SUPPLY_STATUS_NOT_CHARGING, so if that is preferred it could be changed.It should be fixed, yes. Batteries being idle without being full are really common in laptops with battery-life-saving functions (charge/stop-charge threshold control).
Quoted 7 lines
I suspected this might be the case. Is there a way we can get true battery state out of acpi for the battery? I always thought there could be two booleans: charging and discharging.
I guess fully charged isn't just !charging and !discharging.
Richard.
How about such definition: Fully charged == current_capacity >= 90 % of last_capacity && !charging and !discharging?
Alex.
Quoted 25 lines · Alexey Starikovskiy
Quoted 24 lines · Richard Hughes
Quoted 14 lines · Henrique de Moraes Holschuh
Quoted 13 lines · Alexey Starikovskiy
This is probably related to this piece of code (
drivers/acpi/battery.c), similar code exists indrivers/acpi/sbs.c, but it is not relevant to your case:case POWER_SUPPLY_PROP_STATUS: if (battery->state & 0x01) val->intval = POWER_SUPPLY_STATUS_DISCHARGING; else if (battery->state & 0x02) val->intval = POWER_SUPPLY_STATUS_CHARGING; else if (battery->state == 0) val->intval = POWER_SUPPLY_STATUS_FULL; else val->intval = POWER_SUPPLY_STATUS_UNKNOWN; break;Quoted 4 lines
Quoted 1 line
Actually, state==0 means
POWER_SUPPLY_STATUS_NOT_CHARGING, so if that is preferred it could be changed.It should be fixed, yes. Batteries being idle without being full are really common in laptops with battery-life-saving functions (charge/stop-charge threshold control).
I suspected this might be the case. Is there a way we can get true battery state out of acpi for the battery? I always thought there could be two booleans: charging and discharging.
Quoted 5 lines
Quoted 3 lines
I guess fully charged isn't just !charging and !discharging.
Richard.
How about such definition: Fully charged ==
current_capacity>= 90 % oflast_capacity&& !charging and !discharging?
Not good. It is usual to tell the EC to stop charging at 95% or 98%.
I don't understand, why this guesswork over fully charged? If you cannot detect fully charged, then *don't*.
But if you must sinthesize it, and you can get an up-to-date "last full capacity" from the battery when comparing, I suggest:
full = (current capacity == last full capacity) && !charging &&
!discharging
That would *still* be wrong in a few corner cases, but at least they're rare corner cases that happens only when the pack recalibrates its fuel gauge.
If there isn't a reliable way to detect the "full" state, just drop the fully charged detection altogether.
Signature · 4 lines
"One disk to rule them all, One disk to find them. One disk to bring them all and in the darkness grind them. In the Land of Redmond where the shadows lie." -- The Silicon Valley Tarot Henrique Holschuh
Quoted 4 lines · Henrique de Moraes Holschuh
Quoted 1 line · Alexey Starikovskiy
How about such definition: Fully charged ==
current_capacity>= 90 % oflast_capacity&& !charging and !discharging?Not good. It is usual to tell the EC to stop charging at 95% or 98%.
No. You don't understand the idea. EC does not stop charging at 95%, it will treat battery with 95% of charge as fully charged, it will not *start* charging until charge of the battery drops below this threshold. This is needed to save limited number of battery recharges until it dies. So, in other words, if EC does not charge battery, it thinks battery is *full* within some threshold.
Now we talk about sub-second interval, then EC makes a decision to charge or not the battery, and what to report in this sub-second interval. I am trying to apply same logic as EC does --
if it is above some threshold (90, 95, 98 %%) of last_capacity, report it full.
Quoted 9 lines
I don't understand, why this guesswork over fully charged? If you cannot detect fully charged, then *don't*.
But if you must sinthesize it, and you can get an up-to-date "last full capacity" from the battery when comparing, I suggest:
full = (current capacity == last full capacity) && !charging &&
!discharging
certainly, 90% is wrong, but 100% makes a day...
Quoted 3 lines
That would *still* be wrong in a few corner cases, but at least they're rare corner cases that happens only when the pack recalibrates its fuel gauge.
full in this case is not exact term. As any other term beside current_now and voltage_now. Capacity of the battery is estimated, so any number that was depending on it, is estimated too.
Quoted 2 lines
If there isn't a reliable way to detect the "full" state, just drop the fully charged detection altogether.
People are used to see "full" state of the battery. I think we could tolerate not-full-enough for sub-second interval instead of dropping full state altogether.
Regards,
Alex.
PATCH 1/1 ACPI battery driver emits POWER_SUPPLY_STATUS_FULL when power lead plugged in
Quoted 9 lines · Alexey Starikovskiy
Quoted 8 lines
I don't understand, why this guesswork over fully charged? If you cannot detect fully charged, then *don't*.
But if you must sinthesize it, and you can get an up-to-date "last full capacity" from the battery when comparing, I suggest:
full = (current capacity == last full capacity) && !charging &&
!dischargingcertainly, 90% is wrong, but 100% makes a day...
I think we need some sort of logic like this.
Quoted 4 lines
Quoted 2 lines
That would *still* be wrong in a few corner cases, but at least they're rare corner cases that happens only when the pack recalibrates its fuel gauge.
full in this case is not exact term. As any other term beside
current_nowandvoltage_now. Capacity of the battery is estimated, so any number that was depending on it, is estimated too.
Right, never underestimate the brokenness of some people's batteries out there. Coupled with broken BIOS's, some of the fix-up code in HAL is 'interesting'. I think all the fix-up code in HAL belongs in in the kernel.
Quoted 4 lines
Quoted 2 lines
If there isn't a reliable way to detect the "full" state, just drop the fully charged detection altogether.
People are used to see "full" state of the battery. I think we could tolerate not-full-enough for sub-second interval instead of dropping full state altogether.
We shouldn't drop the full state, we should just add some metric like above. What about something like the attached (untested) patch? Would something this be accepted?
Richard.
drivers/acpi/battery.c +33 -1
@@ -138,6 +138,38 @@ static int acpi_battery_technology(struct acpi_battery *battery)static int acpi_battery_get_state (struct acpi_battery *battery); +static int acpi_battery_is_charged (struct acpi_battery *battery) +{ +int percentage; + +/* either charging or discharging */ +if (battery->state !=0 ) +return 0 ; + +/* battery not reporting charge */ +if (battery->full_charge_capacity ==ACPI_BATTERY_VALUE_UNKNOWN || + battery->capacity_now ==0 ) +return 0 ; + +/* good batteries update full_charge as the batteries degrade */ +if (battery->full_charge_capacity !=ACPI_BATTERY_VALUE_UNKNOWN && + battery->full_charge_capacity !=0 ) { + percentage = (100 * battery->capacity_now) / battery->full_charge_capacity; +if (percentage >90 ) +return 1 ; + } + +/* fallback to using design values for broken batteries */ +if (battery->design_capacity !=ACPI_BATTERY_VALUE_UNKNOWN && + battery->design_capacity !=0 ) { + percentage = (100 * battery->capacity_now) / battery->design_capacity; +if (percentage >90 ) +return 1 ; + } + +return 0 ; +} +static int acpi_battery_get_property (struct power_supply *psy,enum power_supply_property psp,union power_supply_propval *val)
@@ -155,7 +187,7 @@ static int acpi_battery_get_property(struct power_supply *psy, val->intval =POWER_SUPPLY_STATUS_DISCHARGING ; else if (battery->state & 0x02) val->intval = POWER_SUPPLY_STATUS_CHARGING; - else if (battery->state == 0) + else if (acpi_battery_is_charged(battery)) val->intval = POWER_SUPPLY_STATUS_FULL; else val->intval = POWER_SUPPLY_STATUS_UNKNOWN;
Looks good to me.
Quoted 34 lines · Richard Hughes
Quoted 9 lines · Alexey Starikovskiy
Quoted 8 lines
I don't understand, why this guesswork over fully charged? If you cannot detect fully charged, then *don't*.
But if you must sinthesize it, and you can get an up-to-date "last full capacity" from the battery when comparing, I suggest:
full = (current capacity == last full capacity) && !charging &&
!dischargingcertainly, 90% is wrong, but 100% makes a day...
I think we need some sort of logic like this.
Quoted 4 lines
Quoted 2 lines
That would *still* be wrong in a few corner cases, but at least they're rare corner cases that happens only when the pack recalibrates its fuel gauge.
full in this case is not exact term. As any other term beside
current_nowandvoltage_now. Capacity of the battery is estimated, so any number that was depending on it, is estimated too.Right, never underestimate the brokenness of some people's batteries out there. Coupled with broken BIOS's, some of the fix-up code in HAL is 'interesting'. I think all the fix-up code in HAL belongs in in the kernel.
Quoted 3 lines
Quoted 2 lines
If there isn't a reliable way to detect the "full" state, just drop the fully charged detection altogether.
People are used to see "full" state of the battery. I think we could tolerate not-full-enough for sub-second interval instead of dropping full state altogether.
We shouldn't drop the full state, we should just add some metric like above. What about something like the attached (untested) patch? Would something this be accepted?
Richard.
drivers/acpi/battery.c static int acpi_battery_technology(struct acpi_battery *battery) · line 159
Quoted 6 lines · Richard Hughes
drivers/acpi/battery.c +6
-0+/* good batteries update full_charge as the batteries degrade */ +if (battery->full_charge_capacity !=ACPI_BATTERY_VALUE_UNKNOWN && + battery->full_charge_capacity !=0 ) { + percentage = (100 * battery->capacity_now) / battery->full_charge_capacity; +if (percentage >90 ) +return 1 ;
You guys have to remember that the hardware can know when the cells are physically full. That has _nothing_ to do with any level estimation, battery cells behave differently when they are full, and that's what the overcharge protection circuitry detects.
So, the above test will still break on any proper battery subsystem with the high watermark set below 100%, as those systems update full_charge_capacity *only* when the cells really are full (and not because the EC decided to stop the charging before they were full).
Thus, it will break if you set the threshold to stop charging (high watermark) above 90% but below 100% on a T-, X-, R- or W-series ThinkPad, for example.
The test would still have to be:
if (battery->full_charge_capacity != ACPI_BATTERY_VALUE_UNKNOWN && battery->full_charge_capacity != 0 && battery->capacity_now == battery->full_charge_capacity) return 1;
or, if there is crap so bad out there that requires it:
if (battery->full_charge_capacity != ACPI_BATTERY_VALUE_UNKNOWN &&
battery->full_charge_capacity != 0 &&
battery->capacity_now == battery->full_charge_capacity) {
percentage = (100 * battery->capacity_now) / battery->full_charge_capacity;
if (percentage > 90)
return 1;to work well on proper battery firmware set to stop before the battery is full.
If that can't work well enough with the crap out there, I am out of ideas, and I'd say we'd have to quirk either the good or the bad systems to properly implement the FULL state.
As for the sub-second "blinks" the EC does in battery states, if one wants to avoid that, better report states only after they have been stable for one or two seconds. Not that a report of CHARGING->IDLE->FULL is incorrect or a problem IMHO, but I don't know if that's what you guys are observing.
Signature · 4 lines
"One disk to rule them all, One disk to find them. One disk to bring them all and in the darkness grind them. In the Land of Redmond where the shadows lie." -- The Silicon Valley Tarot Henrique Holschuh
Quoted 4 lines · Henrique de Moraes Holschuh
So, the above test will still break on any proper battery subsystem with the
high watermark set below 100%, as those systems updatefull_charge_capacity*only* when the cells really are full (and not because the EC decided to stop the charging before they were full).
This is what I observed when testing my patch.
The attached patch checks the last full and design charge, as this seems to work in all cases I have here. In the case of broken batteries or broken hardware, we just return UNKNOWN in this "settling" state, which is much better for userspace than falling back to full.
With the attached patch userspace gets the right states. In the future, maybe we can do some sort of metric over time (watching to see if the present charge changes) but for the most part the patch fixes things up for userspace.
Please review,
Richard.
Quoted 1 line
From
3b0fb1239e5bc064766ffa3d7a45265e722fb9ebMon Sep 17 00:00:00 2001
From: Richard Hughes <[email protected]>
Date: Sun, 25 Jan 2009 15:05:50 +0000
Subject: [PATCH] battery: don't assume we are fully charged when not charging or discharging
On hardware like the T61 it can take a couple of seconds for the battery to start charging after the power is connected, and we incorrectly tell userspace that we are fully charged, and then go back to charging.
Only mark a battery as fully charged when the preset charge matches either the last full charge, or the design charge.
--- drivers/acpi/battery.c | 25 ++++++++++++++++++++++++- 1 files changed, 24 insertions(+), 1 deletions(-)
drivers/acpi/battery.c +24 -1
@@ -138,6 +138,29 @@ static int acpi_battery_technology(struct acpi_battery *battery)static int acpi_battery_get_state (struct acpi_battery *battery); +static int acpi_battery_is_charged (struct acpi_battery *battery) +{ +/* either charging or discharging */ +if (battery->state !=0 ) +return 0 ; + +/* battery not reporting charge */ +if (battery->capacity_now ==ACPI_BATTERY_VALUE_UNKNOWN || + battery->capacity_now ==0 ) +return 0 ; + +/* good batteries update full_charge as the batteries degrade */ +if (battery->full_charge_capacity == battery->capacity_now) +return 1 ; + +/* fallback to using design values for broken batteries */ +if (battery->design_capacity == battery->capacity_now) +return 1 ; + +/* we don't do any sort of metric based on percentages */ +return 0 ; +} +static int acpi_battery_get_property (struct power_supply *psy,enum power_supply_property psp,union power_supply_propval *val)
@@ -155,7 +178,7 @@ static int acpi_battery_get_property(struct power_supply *psy, val->intval =POWER_SUPPLY_STATUS_DISCHARGING ; else if (battery->state & 0x02) val->intval = POWER_SUPPLY_STATUS_CHARGING; - else if (battery->state == 0) + else if (acpi_battery_is_charged(battery)) val->intval = POWER_SUPPLY_STATUS_FULL; else val->intval = POWER_SUPPLY_STATUS_UNKNOWN;
Signature · 1 line
1.6.0.6
Quoted 13 lines · Richard Hughes
Quoted 4 lines · Henrique de Moraes Holschuh
So, the above test will still break on any proper battery subsystem with the
high watermark set below 100%, as those systems updatefull_charge_capacity*only* when the cells really are full (and not because the EC decided to stop the charging before they were full).This is what I observed when testing my patch.
The attached patch checks the last full and design charge, as this seems to work in all cases I have here. In the case of broken batteries or broken hardware, we just return UNKNOWN in this "settling" state, which is much better for userspace than falling back to full.
Quoted 6 lines
With the attached patch userspace gets the right states. In the future, maybe we can do some sort of metric over time (watching to see if the present charge changes) but for the most part the patch fixes things up for userspace.
else val->intval = POWER_SUPPLY_STATUS_UNKNOWN;
This last else should return STATUS_NOT_CHARGING, IMHO. We know this little bit about it.
Quoted 6 lines
Please review,
Richard.
Quoted 3 lines · Alexey Starikovskiy
Quoted 1 line
val->intval = POWER_SUPPLY_STATUS_UNKNOWN;This last else should return
STATUS_NOT_CHARGING, IMHO. We know this little bit about it.
I don't think so; I mean it just as well means STATUS_NOT_DISCHARGING. We don't actually know what the battery is doing internally, hence the UNKNOWN.
Richard.
Re: [patch] ACPI battery driver emits POWER_SUPPLY_STATUS_FULL when power lead plugged in (resend)
In reply to Henrique de Moraes HolschuhQuoted 4 lines · Henrique de Moraes Holschuh
So, the above test will still break on any proper battery subsystem with the
high watermark set below 100%, as those systems updatefull_charge_capacity*only* when the cells really are full (and not because the EC decided to stop the charging before they were full).
This is what I observed when testing my patch.
The attached patch checks the last full and design charge, as this seems to work in all cases I have here. In the case of broken batteries or broken hardware, we just return UNKNOWN in this "settling" state, which is much better for userspace than falling back to full.
With the attached patch userspace gets the right states. In the future, maybe we can do some sort of metric over time (watching to see if the present charge changes) but for the most part the patch fixes things up for userspace.
Please review,
Richard.
Quoted 1 line
From
3b0fb1239e5bc064766ffa3d7a45265e722fb9ebMon Sep 17 00:00:00 2001
From: Richard Hughes <[email protected]>
Date: Sun, 25 Jan 2009 15:05:50 +0000
Subject: [PATCH] battery: don't assume we are fully charged when not charging or discharging
On hardware like the T61 it can take a couple of seconds for the battery to start charging after the power is connected, and we incorrectly tell userspace that we are fully charged, and then go back to charging.
Only mark a battery as fully charged when the preset charge matches either the last full charge, or the design charge.
--- drivers/acpi/battery.c | 25 ++++++++++++++++++++++++- 1 files changed, 24 insertions(+), 1 deletions(-)
drivers/acpi/battery.c +24 -1
@@ -138,6 +138,29 @@ static int acpi_battery_technology(struct acpi_battery *battery)static int acpi_battery_get_state (struct acpi_battery *battery); +static int acpi_battery_is_charged (struct acpi_battery *battery) +{ +/* either charging or discharging */ +if (battery->state !=0 ) +return 0 ; + +/* battery not reporting charge */ +if (battery->capacity_now ==ACPI_BATTERY_VALUE_UNKNOWN || + battery->capacity_now ==0 ) +return 0 ; + +/* good batteries update full_charge as the batteries degrade */ +if (battery->full_charge_capacity == battery->capacity_now) +return 1 ; + +/* fallback to using design values for broken batteries */ +if (battery->design_capacity == battery->capacity_now) +return 1 ; + +/* we don't do any sort of metric based on percentages */ +return 0 ; +} +static int acpi_battery_get_property (struct power_supply *psy,enum power_supply_property psp,union power_supply_propval *val)
@@ -155,7 +178,7 @@ static int acpi_battery_get_property(struct power_supply *psy, val->intval =POWER_SUPPLY_STATUS_DISCHARGING ; else if (battery->state & 0x02) val->intval = POWER_SUPPLY_STATUS_CHARGING; - else if (battery->state == 0) + else if (acpi_battery_is_charged(battery)) val->intval = POWER_SUPPLY_STATUS_FULL; else val->intval = POWER_SUPPLY_STATUS_UNKNOWN;
Signature · 1 line
1.6.0.6
Re: [patch] ACPI battery driver emits POWER_SUPPLY_STATUS_FULL when power lead plugged in (resend)
Quoted 9 lines · Richard Hughes
The attached patch checks the last full and design charge, as this seems to work in all cases I have here. In the case of broken batteries or broken hardware, we just return UNKNOWN in this "settling" state, which is much better for userspace than falling back to full.
With the attached patch userspace gets the right states. In the future, maybe we can do some sort of metric over time (watching to see if the present charge changes) but for the most part the patch fixes things up for userspace.
I am ok with this patch, but it does have *one* corner case.
Brand new good batteries will be reported as full while still charging, when they're near 100% (they will be above the design capacity).
That isn't enough for me to complain about the patch, and the patch makes it MUCH better than the current broken behaviour.
So you can have my Acked-by if you want it, for whatever little it is worth.
Signature · 4 lines
"One disk to rule them all, One disk to find them. One disk to bring them all and in the darkness grind them. In the Land of Redmond where the shadows lie." -- The Silicon Valley Tarot Henrique Holschuh
Len Brown
reviewerRe: [patch] ACPI battery driver emits POWER_SUPPLY_STATUS_FULL when power lead plugged in (resend)
Quoted 13 lines · Henrique de Moraes Holschuh
Quoted 9 lines · Richard Hughes
The attached patch checks the last full and design charge, as this seems to work in all cases I have here. In the case of broken batteries or broken hardware, we just return UNKNOWN in this "settling" state, which is much better for userspace than falling back to full.
With the attached patch userspace gets the right states. In the future, maybe we can do some sort of metric over time (watching to see if the present charge changes) but for the most part the patch fixes things up for userspace.
I am ok with this patch, but it does have *one* corner case.
Quoted 7 lines
Brand new good batteries will be reported as full while still charging, when they're near 100% (they will be above the design capacity).
That isn't enough for me to complain about the patch, and the patch makes it MUCH better than the current broken behaviour.
So you can have my Acked-by if you want it, for whatever little it is worth.
Applied to acpi-test.
thanks,
Len Brown, Intel Open Source Technology Center
Re: [patch] ACPI battery driver emits POWER_SUPPLY_STATUS_FULL when power lead plugged in (resend)
Quoted 1 line · Len Brown
Applied to acpi-test.
Thanks dude.
Richard.