Skip to contentSkip to conversation

staging/wlan-ng: block ioctls until card fully initialised

PATCH New Richard Kennedy 2 participants 4 messages Feb 17, 2009 – Feb 20, 2009 3 messages not in the archive Staging

lore
Share & tools
lore
#0 lore raw

PATCH 1/1 staging/wlan-ng: block ioctls until card fully initialised

Add a mutex to block ioctls before the card is fully initialised and only allow one ioctl at a time.
This stops udev trying to load the firmware before to card is fully up.

patch ported from wlan-ng-devel

Karl Relton <[email protected]> spotted that this was missing from the staging version,
http://lists.linux-wlan.com/pipermail/linux-wlan-devel/2009-February/003890.html

---
This has only had basic testing, & I haven't tried loading the firmware yet.
regards
Richard

drivers/staging/wlan-ng/p80211netdev.c +14 -0
index 59e5ad1..f6cc298 100644
@@ -623,6 +623,7 @@ static int p80211knetdev_do_ioctl(netdevice_t *dev, struct ifreq *ifr, int cmd)
 
 	WLAN_LOG_DEBUG(2, "rx'd ioctl, cmd=%d, len=%d\n", cmd, req->len);
 
+	mutex_lock(&wlandev->ioctl_lock);
 #ifdef SIOCETHTOOL
 	if (cmd == SIOCETHTOOL) {
 		result = p80211netdev_ethtool(wlandev, (void __user *) ifr->ifr_data);
@@ -662,6 +663,7 @@ static int p80211knetdev_do_ioctl(netdevice_t *dev, struct ifreq *ifr, int cmd)
 		result = -ENOMEM;
 	}
 bail:
+	mutex_unlock(&wlandev->ioctl_lock);
 	DBFEXIT;
 
 	return result; /* If allocate,copyfrom or copyto fails, return errno */
@@ -823,6 +825,13 @@ int wlan_setup(wlandevice_t *wlandev)
 		dev->ml_priv = wlandev;
 		dev->hard_start_xmit =	p80211knetdev_hard_start_xmit;
 		dev->get_stats =	p80211knetdev_get_stats;
+
+		mutex_init(&wlandev->ioctl_lock);
+		/* block ioctls until fully initialised. Don't forget to call
+		   allow_ioctls at some point!*/
+		mutex_lock(&wlandev->ioctl_lock);
+
+
 #ifdef HAVE_PRIVATE_IOCTL
 		dev->do_ioctl = 	p80211knetdev_do_ioctl;
 #endif
@@ -1207,3 +1216,8 @@ static void p80211knetdev_tx_timeout( netdevice_t *netdev)
 
 	DBFEXIT;
 }
+
+
+void p80211_allow_ioctls(wlandevice_t *wlandev) {
+	mutex_unlock(&wlandev->ioctl_lock);
+}
drivers/staging/wlan-ng/p80211netdev.h +5 -0
index 940146f..da49552 100644
@@ -235,6 +235,8 @@ typedef struct wlandevice
         u8			spy_number;
         char			spy_address[IW_MAX_SPY][ETH_ALEN];
         struct iw_quality       spy_stat[IW_MAX_SPY];
+
+	struct mutex ioctl_lock;
 } wlandevice_t;
 
 /* WEP stuff */
@@ -251,4 +253,7 @@ int	unregister_wlandev(wlandevice_t *wlandev);
 void	p80211netdev_rx(wlandevice_t *wlandev, struct sk_buff *skb);
 void	p80211netdev_hwremoved(wlandevice_t *wlandev);
 
+void p80211_allow_ioctls(wlandevice_t *wlandev);
+
+
 #endif
drivers/staging/wlan-ng/prism2usb.c +1 -1
index 8f7b1f2..78c7504 100644
@@ -149,7 +149,7 @@ static int prism2sta_probe_usb(
 
  done:
 	DBFEXIT;
-
+	p80211_allow_ioctls(wlandev);
 	usb_set_intfdata(interface, wlandev);
 	return result;
 }

A message that is not in the archive (sent off-list or not yet received): 1234213202.6875.70.camel@dellpc

A message that is not in the archive (sent off-list or not yet received): [email protected]

A message that is not in the archive (sent off-list or not yet received): 1234478293.17792.1.camel@dellpc

#4 lore raw
Quoted 9 lines · Richard Kennedy

Add a mutex to block ioctls before the card is fully initialised and only allow one ioctl at a time.
This stops udev trying to load the firmware before to card is fully up.

patch ported from wlan-ng-devel

Karl Relton <[email protected]> spotted that this was missing from the staging version,
http://lists.linux-wlan.com/pipermail/linux-wlan-devel/2009-February/003890.html

Karl sent me a patch a few days before you that also added this functionality.

Unfortunatly, both of your patches don't apply to the latest version of the wlan-ng driver as it has had a lot of work done on it recently.

Could one of you grab the linux-next tree and make a patch up against the version in it so that I can apply this?

thanks,

greg k-h

#5 lore raw
Quoted 17 lines · Greg KH
Quoted 9 lines · Richard Kennedy

Add a mutex to block ioctls before the card is fully initialised and only allow one ioctl at a time.
This stops udev trying to load the firmware before to card is fully up.

patch ported from wlan-ng-devel

Karl Relton <[email protected]> spotted that this was missing from the staging version,
http://lists.linux-wlan.com/pipermail/linux-wlan-devel/2009-February/003890.html

Karl sent me a patch a few days before you that also added this functionality.

Unfortunatly, both of your patches don't apply to the latest version of the wlan-ng driver as it has had a lot of work done on it recently.

Quoted 6 lines

Could one of you grab the linux-next tree and make a patch up against the version in it so that I can apply this?

thanks,

greg k-h

Sorry about that, I'd forgotten that wlan-ng was included in linux-next.

I've updated the patch and am just testing it & will post it shortly.

BTW thanks to Moritz Muehlenhoff for the clean-ups.

regards
Richard

#6 lore raw

PATCH 1/1 linux-next/staging/wlan-ng: block ioctls until card fully initialised

In reply to Greg KH

Add a mutex to block ioctls before the card is fully initialised and only allow one ioctl at a time.
This stops udev trying to load the firmware before to card is fully up.

patch ported from wlan-ng-devel

Karl Relton <[email protected]> spotted that this was missing from the staging version,
http://lists.linux-wlan.com/pipermail/linux-wlan-devel/2009-February/003890.html

---
Hi Greg,

patch against linux-next-20090219.
booted & working on my laptop.

sorry about the delay, it's taken me a while to get linux-next running on my laptop.

regards
Richard

drivers/staging/wlan-ng/p80211netdev.c +14 -0
index 50fa8d6..b2a606a 100644
@@ -567,6 +567,8 @@ static int p80211knetdev_do_ioctl(netdevice_t *dev, struct ifreq *ifr, int cmd)
 
 	pr_debug("rx'd ioctl, cmd=%d, len=%d\n", cmd, req->len);
 
+	mutex_lock(&wlandev->ioctl_lock);
+
 #ifdef SIOCETHTOOL
 	if (cmd == SIOCETHTOOL) {
 		result =
@@ -607,6 +609,8 @@ static int p80211knetdev_do_ioctl(netdevice_t *dev, struct ifreq *ifr, int cmd)
 		result = -ENOMEM;
 	}
 bail:
+	mutex_unlock(&wlandev->ioctl_lock);
+
 	return result;		/* If allocate,copyfrom or copyto fails, return errno */
 }
 
@@ -758,6 +762,11 @@ int wlan_setup(wlandevice_t *wlandev)
 		dev->open = p80211knetdev_open;
 		dev->stop = p80211knetdev_stop;
 
+		mutex_init(&wlandev->ioctl_lock);
+		/* block ioctls until fully initialised. Don't forget to call
+		   allow_ioctls at some point!*/
+		mutex_lock(&wlandev->ioctl_lock);
+
 #if (WIRELESS_EXT < 21)
 		dev->get_wireless_stats = p80211wext_get_wireless_stats;
 #endif
@@ -1098,3 +1107,8 @@ static void p80211knetdev_tx_timeout(netdevice_t *netdev)
 		netif_wake_queue(wlandev->netdev);
 	}
 }
+
+void p80211_allow_ioctls(wlandevice_t *wlandev)
+{
+	mutex_unlock(&wlandev->ioctl_lock);
+}
drivers/staging/wlan-ng/p80211netdev.h +3 -1
index 42e3b92..b96090d 100644
@@ -227,6 +227,8 @@ typedef struct wlandevice {
 	u8 spy_number;
 	char spy_address[IW_MAX_SPY][ETH_ALEN];
 	struct iw_quality spy_stat[IW_MAX_SPY];
+
+	struct mutex ioctl_lock;
 } wlandevice_t;
 
 /* WEP stuff */
@@ -242,5 +244,5 @@ int register_wlandev(wlandevice_t *wlandev);
 int unregister_wlandev(wlandevice_t *wlandev);
 void p80211netdev_rx(wlandevice_t *wlandev, struct sk_buff *skb);
 void p80211netdev_hwremoved(wlandevice_t *wlandev);
-
+void p80211_allow_ioctls(wlandevice_t *wlandev);
 #endif
drivers/staging/wlan-ng/prism2usb.c +1 -0
index 252312e..d8a1298 100644
@@ -170,6 +170,7 @@ failed:
 	wlandev = NULL;
 
 done:
+	p80211_allow_ioctls(wlandev);
 	usb_set_intfdata(interface, wlandev);
 	return result;
 }