Skip to contentSkip to conversation

Add support to SB800 SMBus changes

PATCH In review Shane Huang 2 participants 2 messages Feb 20, 2009 – Feb 27, 2009

Subsystems (2)
lore
Share & tools
lore
#0 lore raw

PATCH 1/1 Add support to SB800 SMBus changes

The original patch is updated with Jean's nice suggestions, please check it.

Thanks.
Shane

=== CUT HERE ===
This version of driver adds support for the AMD SB800 Family series of products. Major changes include the changes to addressing the SMBUS registers at different location from the locations in the previous compatible parts from AMD such as SB400/SB600/SB700. For SB800, the main features and register definitions of SMBUS and other interfaces are still compatible with the previous products with the only change being in how to access the internal registers for these blocks may differ.

drivers/i2c/busses/i2c-piix4.c +70 -1
diff -ruN a/drivers/i2c/busses/i2c-piix4.c b/drivers/i2c/busses/i2c-piix4.c
@@ -226,6 +226,68 @@
 	return 0;
 }
 
+static int __devinit piix4_setup_sb800(struct pci_dev *PIIX4_dev,
+				const struct pci_device_id *id)
+{
+	unsigned short smba_idx = 0xcd6;
+	u8 smba_en_lo, smba_en_hi, i2ccfg, i2ccfg_offset = 0x10, smb_en = 0x2c;
+
+	/* SB800 SMBus does not support forcing address */
+	if (force || force_addr)
+		dev_info(&PIIX4_dev->dev, "SB800 SMBus does not support "
+			"forcing address!\n");
+
+	/* Determine the address of the SMBus areas */
+	if (!request_region(smba_idx, 2, "smba_idx")) {
+		dev_err(&PIIX4_dev->dev, "SMBus base address index region "
+			"0x%x already in use!\n", smba_idx);
+		return -EBUSY;
+	}
+	outb_p(smb_en, smba_idx);
+	smba_en_lo = inb_p(smba_idx + 1);
+	outb_p(smb_en + 1, smba_idx);
+	smba_en_hi = inb_p(smba_idx + 1);
+	release_region(smba_idx, 2);
+
+	if ((smba_en_lo & 1) == 0) {
+		dev_err(&PIIX4_dev->dev,
+			"Host SMBus controller not enabled!\n");
+		return -ENODEV;
+	}
+
+	piix4_smba = ((smba_en_hi << 8) | smba_en_lo) & 0xffe0;
+	if (acpi_check_region(piix4_smba, SMBIOSIZE, piix4_driver.name))
+		return -EBUSY;
+
+	if (!request_region(piix4_smba, SMBIOSIZE, piix4_driver.name)) {
+		dev_err(&PIIX4_dev->dev, "SMBus region 0x%x already in use!\n",
+			piix4_smba);
+		return -EBUSY;
+	}
+
+	/* Request the SMBus I2C bus config region */
+	if (!request_region(piix4_smba + i2ccfg_offset, 1, "i2ccfg")) {
+		dev_err(&PIIX4_dev->dev, "SMBus I2C bus config region "
+			"0x%x already in use!\n", piix4_smba + i2ccfg_offset);
+		release_region(piix4_smba, SMBIOSIZE);
+		piix4_smba = 0;
+		return -EBUSY;
+	}
+	i2ccfg = inb_p(piix4_smba + i2ccfg_offset);
+	release_region(piix4_smba + i2ccfg_offset, 1);
+
+	if (i2ccfg & 1)
+		dev_dbg(&PIIX4_dev->dev, "Using IRQ for SMBus.\n");
+	else
+		dev_dbg(&PIIX4_dev->dev, "Using SMI# for SMBus.\n");
+
+	dev_info(&PIIX4_dev->dev,
+		 "SMBus Host Controller at 0x%x, revision %d\n",
+		 piix4_smba, i2ccfg >> 4);
+
+	return 0;
+}
+
 static int piix4_transaction(void)
 {
 	int temp;
@@ -434,7 +496,14 @@
 {
 	int retval;
 
-	retval = piix4_setup(dev, id);
+	if ((dev->vendor == PCI_VENDOR_ID_ATI) &&
+	    (dev->device == PCI_DEVICE_ID_ATI_SBX00_SMBUS) &&
+	    (dev->revision >= 0x40))
+		/* base address location etc changed in SB800 */
+		retval = piix4_setup_sb800(dev, id);
+	else
+		retval = piix4_setup(dev, id);
+
 	if (retval)
 		return retval;
 
#1 lore raw

Hi Shane,

Quoted 15 lines · Shane Huang

The original patch is updated with Jean's nice suggestions, please check it.

Thanks.
Shane

=== CUT HERE ===
This version of driver adds support for the AMD SB800 Family series of products. Major changes include the changes to addressing the SMBUS registers at different location from the locations in the previous compatible parts from AMD such as SB400/SB600/SB700. For SB800, the main features and register definitions of SMBUS and other interfaces are still compatible with the previous products with the only change being in how to access the internal registers for these blocks may differ.

Quoted 1 line

This new version of the patch looks acceptable to me. Even though I find it unfortunate that ATI/AMD changed the hardware implementation to something which is more complex to handle with no good reason that I can see :(

Quoted 8 lines

diff -ruN a/drivers/i2c/busses/i2c-piix4.c b/drivers/i2c/busses/i2c-piix4.c

drivers/i2c/busses/i2c-piix4.c +0 -0
@@ -226,6 +226,68 @@
 	return 0;
 }
 

drivers/i2c/busses/i2c-piix4.c line 238

Quoted 10 lines
drivers/i2c/busses/i2c-piix4.c +10 -0
+static int __devinit piix4_setup_sb800(struct pci_dev *PIIX4_dev,
+				const struct pci_device_id *id)
+{
+	unsigned short smba_idx = 0xcd6;
+	u8 smba_en_lo, smba_en_hi, i2ccfg, i2ccfg_offset = 0x10, smb_en = 0x2c;
+
+	/* SB800 SMBus does not support forcing address */
+	if (force || force_addr)
+		dev_info(&PIIX4_dev->dev, "SB800 SMBus does not support "
+			"forcing address!\n");

I would promote this to dev_warn(), or even dev_err() and fail.

Quoted 61 lines
drivers/i2c/busses/i2c-piix4.c +53 -1
+
+	/* Determine the address of the SMBus areas */
+	if (!request_region(smba_idx, 2, "smba_idx")) {
+		dev_err(&PIIX4_dev->dev, "SMBus base address index region "
+			"0x%x already in use!\n", smba_idx);
+		return -EBUSY;
+	}
+	outb_p(smb_en, smba_idx);
+	smba_en_lo = inb_p(smba_idx + 1);
+	outb_p(smb_en + 1, smba_idx);
+	smba_en_hi = inb_p(smba_idx + 1);
+	release_region(smba_idx, 2);
+
+	if ((smba_en_lo & 1) == 0) {
+		dev_err(&PIIX4_dev->dev,
+			"Host SMBus controller not enabled!\n");
+		return -ENODEV;
+	}
+
+	piix4_smba = ((smba_en_hi << 8) | smba_en_lo) & 0xffe0;
+	if (acpi_check_region(piix4_smba, SMBIOSIZE, piix4_driver.name))
+		return -EBUSY;
+
+	if (!request_region(piix4_smba, SMBIOSIZE, piix4_driver.name)) {
+		dev_err(&PIIX4_dev->dev, "SMBus region 0x%x already in use!\n",
+			piix4_smba);
+		return -EBUSY;
+	}
+
+	/* Request the SMBus I2C bus config region */
+	if (!request_region(piix4_smba + i2ccfg_offset, 1, "i2ccfg")) {
+		dev_err(&PIIX4_dev->dev, "SMBus I2C bus config region "
+			"0x%x already in use!\n", piix4_smba + i2ccfg_offset);
+		release_region(piix4_smba, SMBIOSIZE);
+		piix4_smba = 0;
+		return -EBUSY;
+	}
+	i2ccfg = inb_p(piix4_smba + i2ccfg_offset);
+	release_region(piix4_smba + i2ccfg_offset, 1);
+
+	if (i2ccfg & 1)
+		dev_dbg(&PIIX4_dev->dev, "Using IRQ for SMBus.\n");
+	else
+		dev_dbg(&PIIX4_dev->dev, "Using SMI# for SMBus.\n");
+
+	dev_info(&PIIX4_dev->dev,
+		 "SMBus Host Controller at 0x%x, revision %d\n",
+		 piix4_smba, i2ccfg >> 4);
+
+	return 0;
+}
+
 static int piix4_transaction(void)
 {
 	int temp;
@@ -434,7 +496,14 @@
 {
 	int retval;
 
-	retval = piix4_setup(dev, id);
+	if ((dev->vendor == PCI_VENDOR_ID_ATI) &&

drivers/i2c/busses/i2c-piix4.c line 509

Quoted 10 lines
drivers/i2c/busses/i2c-piix4.c +7 -0
+	    (dev->device == PCI_DEVICE_ID_ATI_SBX00_SMBUS) &&
+	    (dev->revision >= 0x40))
+		/* base address location etc changed in SB800 */
+		retval = piix4_setup_sb800(dev, id);
+	else
+		retval = piix4_setup(dev, id);
+
 	if (retval)
 		return retval;
 

All the rest looks good, I'll apply your patch now.

Signature · 1 line
Jean Delvare