v4l/bttv Add support to the GeoVision GV-800(S)
PATCH 1/1 v4l/bttv Add support to the GeoVision GV-800(S)
Hello all,
I have a GeoVision GV-800(S) card, it has 4 CONEXANT BT878A chips. It has 16 video inputs and 4 audio inputs, and it is almost identical to the GV-800, as seen on http://bttv-gallery.de .
The only difference appears to be the analog mux, it has a CD22M3494 in place of the MT8816AP. The card has a blue PCB, as seen in this
picture: http://www.gsbr.com.br/imagem/kits/GeoVision%20GV%20800.jpg .
This card wasn't originally supported, and it was detected as UNKNOWN/GENERIC. The video inputs weren't working, so I tried "forcing" a few cards like the GeoVision GV-600, but there was still no video. So I made a patch to support this card, based on the Kodicom 4400r.
The GV-800(S) is identified as follows:
# lspci ... 02:00.0 Multimedia video controller: Brooktree Corporation Bt878 Video Capture (rev 11) 02:00.1 Multimedia controller: Brooktree Corporation Bt878 Audio Capture (rev 11) 02:04.0 Multimedia video controller: Brooktree Corporation Bt878 Video Capture (rev 11) 02:04.1 Multimedia controller: Brooktree Corporation Bt878 Audio Capture (rev 11) 02:08.0 Multimedia video controller: Brooktree Corporation Bt878 Video Capture (rev 11) 02:08.1 Multimedia controller: Brooktree Corporation Bt878 Audio Capture (rev 11) 02:0c.0 Multimedia video controller: Brooktree Corporation Bt878 Video Capture (rev 11) 02:0c.1 Multimedia controller: Brooktree Corporation Bt878 Audio Capture (rev 11)
# lspci -nv
...
02:00.0 0400: 109e:036e (rev 11)
Subsystem: 800a:763d
Flags: bus master, medium devsel, latency 32, IRQ 10
Memory at cdfff000 (32-bit, prefetchable) [size=4K]
Capabilities: [44] Vital Product Data <?>
Capabilities: [4c] Power Management version 2
Kernel modules: bttv02:00.1 0480: 109e:0878 (rev 11)
Subsystem: 800a:763d
Flags: bus master, medium devsel, latency 32, IRQ 10 Memory at cdffe000 (32-bit, prefetchable) [size=4K]
Capabilities: [44] Vital Product Data <?>
Capabilities: [4c] Power Management version 2
02:04.0 0400: 109e:036e (rev 11)
Subsystem: 800b:763d
Flags: bus master, medium devsel, latency 32, IRQ 10 Memory at cdffd000 (32-bit, prefetchable) [size=4K]
Capabilities: [44] Vital Product Data <?>
Capabilities: [4c] Power Management version 2 Kernel modules: bttv
02:04.1 0480: 109e:0878 (rev 11)
Subsystem: 800b:763d
Flags: bus master, medium devsel, latency 32, IRQ 10 Memory at cdffc000 (32-bit, prefetchable) [size=4K]
Capabilities: [44] Vital Product Data <?>
Capabilities: [4c] Power Management version 2
02:08.0 0400: 109e:036e (rev 11)
Subsystem: 800c:763d
Flags: bus master, medium devsel, latency 32, IRQ 10 Memory at cdffb000 (32-bit, prefetchable) [size=4K]
Capabilities: [44] Vital Product Data <?>
Capabilities: [4c] Power Management version 2 Kernel modules: bttv
02:08.1 0480: 109e:0878 (rev 11)
Subsystem: 800c:763d
Flags: bus master, medium devsel, latency 32, IRQ 10 Memory at cdffa000 (32-bit, prefetchable) [size=4K]
Capabilities: [44] Vital Product Data <?>
Capabilities: [4c] Power Management version 2
02:0c.0 0400: 109e:036e (rev 11)
Subsystem: 800d:763d
Flags: bus master, medium devsel, latency 32, IRQ 10 Memory at cdff9000 (32-bit, prefetchable) [size=4K]
Capabilities: [44] Vital Product Data <?>
Capabilities: [4c] Power Management version 2 Kernel modules: bttv
02:0c.1 0480: 109e:0878 (rev 11)
Subsystem: 800d:763d
Flags: bus master, medium devsel, latency 32, IRQ 10 Memory at cdff8000 (32-bit, prefetchable) [size=4K]
Capabilities: [44] Vital Product Data <?>
Capabilities: [4c] Power Management version 2
As you can see, the GV-800(S) card is almost identical to the GV-800 on bttv-gallery, so this patch might also work for that card. If not, only a few changes should be required on the gv800s_write() function.
After this patch, the video inputs work correctly on linux 2.6.24 and 2.6.27 using the software 'motion'. The input order may seem a little odd, but it's the order the original software/driver uses, and I decided to keep that order to get the most out of the card.
I tried to get the audio working with the snd-bt87x module, but I only get noise from every audio input, even after selecting a different mux with alsamixer. Also, after trying to play sound from those sources, I randomly get a RISC error about an invalid RISC opcode, and then that output stops working. I also can't change the sampling rate when recording. Any pointers to adding audio support are welcome.
This mail was sent using Evolution as described in email-clients.txt, I hope the tabs/spaces are now ok.
---
linux/Documentation/video4linux/CARDLIST.bttv +2 -0
@@ -155,3 +155,5 @@ 154 -> PHYTEC VD-012-X1 (bt878) 155 -> PHYTEC VD-012-X2 (bt878) 156 -> IVCE-8784 [0000:f050,0001:f050,0002:f050,0003:f050] +157 -> Geovision GV-800(S) (master) [800a:763d] +158 -> Geovision GV-800(S) (slave) [800b:763d,800c:763d,800d:763d]
linux/drivers/media/video/bt8xx/bttv-cards.c +180 -1
211 lines not on this page · raw message
linux/drivers/media/video/bt8xx/bttv.h +2 -0
@@ -182,6 +182,8 @@#define BTTV_BOARD_VD012_X1 0x9a#define BTTV_BOARD_VD012_X2 0x9b#define BTTV_BOARD_IVCE8784 0x9c +#define BTTV_BOARD_GEOVISION_GV800S 0x9d +#define BTTV_BOARD_GEOVISION_GV800S_SL 0x9e/* more card-specific defines */
--
Bruno Christo
Bacharel em Ciência da Computação - UFSM