powerpc: add fsl, fifo-depth property to Freescale SSI device nodes
Subsystems (3)
PATCH 1/1 powerpc: add fsl, fifo-depth property to Freescale SSI device nodes
The Freescale Serial Synchronous Interface (SSI) is an audio device present on some Freescale SOCs. Various implementations of the SSI have a different transmit and receive FIFO depth, but are otherwise identical. To support these variations, add a new property fsl,fifo-depth to the SSI node that specifies the depth of the FIFOs.
Also update the MPC8610 HPCD device tree with this property.
---
Updates to the SSI audio driver will come later. Currently, this driver supports only one Freescale SOC, and so it's hard-coded to use the value 8. If/when this driver is updated to support other SOCs (e.g. the i.MX parts that have a FIFO depth of 15), the driver will check for this property. I just want to get this DTS change in now.
Documentation/powerpc/dts-bindings/fsl/ssi.txt | 2 ++ arch/powerpc/boot/dts/mpc8610_hpcd.dts | 2 ++ 2 files changed, 4 insertions(+), 0 deletions(-)
Documentation/powerpc/dts-bindings/fsl/ssi.txt +2 -0
@@ -30,6 +30,8 @@ Required properties: - fsl,capture-dma: phandle to a node for the DMA channel to use for capture (recording) of audio. This is typically dictated by SOC design. See the notes below. +- fsl,fifo-depth: the number of elements in the transmit and receive FIFOs. + This number is the maximum allowed value for SFCSR[TFWM0]. Optional properties: - codec-handle : phandle to a 'codec' node that defines an audio
arch/powerpc/boot/dts/mpc8610_hpcd.dts +2 -0
@@ -217,6 +217,7 @@ codec-handle = <&cs4270>; fsl,playback-dma = <&dma00>; fsl,capture-dma = <&dma01>; + fsl,fifo-depth = <8>; }; ssi@16100 {
@@ -225,6 +226,7 @@ reg = <0x16100 0x100>; interrupt-parent = <&mpic>; interrupts = <63 2>; + fsl,fifo-depth = <8>; }; dma@21300 {
Signature · 1 line
1.6.1.3
Kumar Gala
AppliedQuoted 17 lines · Timur Tabi
The Freescale Serial Synchronous Interface (SSI) is an audio device present on some Freescale SOCs. Various implementations of the SSI have a different transmit and receive FIFO depth, but are otherwise identical. To support these variations, add a new property fsl,fifo-depth to the SSI node that specifies the depth of the FIFOs.
Also update the MPC8610 HPCD device tree with this property.
Signed-off-by Timur Tabi <[email protected]>---
Updates to the SSI audio driver will come later. Currently, this driver supports only one Freescale SOC, and so it's hard-coded to use the value 8. If/when this driver is updated to support other SOCs (e.g. the i.MX parts that have a FIFO depth of 15), the driver will check for this property. I just want to get this DTS change in now.
Quoted 3 lines
Documentation/powerpc/dts-bindings/fsl/ssi.txt | 2 ++ arch/powerpc/boot/dts/mpc8610_hpcd.dts | 2 ++ 2 files changed, 4 insertions(+), 0 deletions(-)
applied to next
- k