spi: s6000 spi host driver

PATCH In review Daniel Glöckner 2 participants 9 messages Mar 23, 2009 – Apr 2, 2009

Subsystems (2)

SPI Tensilica Xtensa port (xtensa)

lore

Share & tools

lore

Daniel Glöckner

author

2009-03-23 15:34 UTC #0 lore raw

PATCH 1/6 spi: s6000 spi host driver

From: Johannes Weiner <[email protected]>

The host controller has a 128 bit buffer which is shared between rx and tx. Filling and reading of this buffer happens in a dedicated workqueue. We always fill it with an integer number of words but don't cross spi_transfer boundaries.

The driver usually uses interrupts but falls back to polling if the transfer is expected to finish within a certain window of time.

Signed-off-by Johannes Weiner <[email protected]>

Signed-off-by Daniel Glöckner <[email protected]>

---
 drivers/spi/Kconfig           |    6 +
 drivers/spi/Makefile          |    1 +
 drivers/spi/spi_s6000.c       |  648 +++++++++++++++++++++++++++++++++++++++++
 drivers/spi/spi_s6000.h       |   26 ++
 include/linux/spi/spi_s6000.h |   10 +
 5 files changed, 691 insertions(+), 0 deletions(-)
 create mode 100644 drivers/spi/spi_s6000.c
 create mode 100644 drivers/spi/spi_s6000.h
 create mode 100644 include/linux/spi/spi_s6000.h

drivers/spi/Kconfig +6 -0

index 83a185d..c373717 100644
@@ -197,6 +197,12 @@ config SPI_S3C24XX_GPIO
 	  the inbuilt hardware cannot provide the transfer mode, or
 	  where the board is using non hardware connected pins.
 
+config SPI_S6000
+	tristate "S6000 SPI master"
+	depends on SPI_MASTER && XTENSA_VARIANT_S6000
+	help
+	  SPI driver for the Stretch S6000 family SoCs.
+
 config SPI_SH_SCI
 	tristate "SuperH SCI SPI controller"
 	depends on SUPERH

drivers/spi/Makefile +1 -0

index 5d04519..3a4dae7 100644
@@ -27,6 +27,7 @@ obj-$(CONFIG_SPI_MPC52xx_PSC)		+= mpc52xx_psc_spi.o
 obj-$(CONFIG_SPI_MPC83xx)		+= spi_mpc83xx.o
 obj-$(CONFIG_SPI_S3C24XX_GPIO)		+= spi_s3c24xx_gpio.o
 obj-$(CONFIG_SPI_S3C24XX)		+= spi_s3c24xx.o
+obj-$(CONFIG_SPI_S6000)			+= spi_s6000.o
 obj-$(CONFIG_SPI_TXX9)			+= spi_txx9.o
 obj-$(CONFIG_SPI_XILINX)		+= xilinx_spi.o
 obj-$(CONFIG_SPI_SH_SCI)		+= spi_sh_sci.o

drivers/spi/spi_s6000.c new file +648 -0

648 lines not on this page · raw message

drivers/spi/spi_s6000.h new file +26 -0

new file mode 100644
index 0000000..eff82e3
@@ -0,0 +1,26 @@
+#ifndef __DRIVERS_SPI_SPI_S6000_H
+#define __DRIVERS_SPI_SPI_S6000_H
+
+#define S6_SPI_RX0		0x00
+#define S6_SPI_RX1		0x04
+#define S6_SPI_RX2		0x08
+#define S6_SPI_RX3		0x0C
+#define S6_SPI_TX0		0x00
+#define S6_SPI_TX1		0x04
+#define S6_SPI_TX2		0x08
+#define S6_SPI_TX3		0x0C
+#define S6_SPI_CTRL		0x10
+#define S6_SPI_CTRL_GO_BSY		0
+#define S6_SPI_CTRL_Rx_NEG		1
+#define S6_SPI_CTRL_Tx_NEG		2
+#define S6_SPI_CTRL_CHAR_LEN		3
+#define S6_SPI_CTRL_LSB			10
+#define S6_SPI_CTRL_IE			11
+#define S6_SPI_CTRL_ASS			12
+#define S6_SPI_CTRL_CPOL		13
+#define S6_SPI_DIVIDER		0x14
+#define S6_SPI_DIVIDER_MAX		0xffff
+#define S6_SPI_SS		0x18
+#define S6_SPI_INT_CLR		0x20
+
+#endif

include/linux/spi/spi_s6000.h new file +10 -0

new file mode 100644
index 0000000..9a02bb5
@@ -0,0 +1,10 @@
+#ifndef __LINUX_SPI_SPI_S6000_H
+#define __LINUX_SPI_SPI_S6000_H
+
+struct s6_spi_platform_data {
+	const char *clock;
+	s16 bus_num;
+	u8 cs_polarity;
+};
+
+#endif

Signature · 1 line

1.6.2.107.ge47ee

Daniel Glöckner

author

2009-03-23 15:34 UTC #1 lore raw

PATCH 2/6 xtensa: add s6000 spi host to s6105 platform

Signed-off-by Daniel Glöckner <[email protected]>

---
 arch/xtensa/platforms/s6105/device.c |   48 ++++++++++++++++++++++++++++++++++
 arch/xtensa/platforms/s6105/setup.c  |    5 +++-
 2 files changed, 52 insertions(+), 1 deletions(-)

arch/xtensa/platforms/s6105/device.c +48 -0

index 9394e6f..a7ea916 100644
@@ -14,6 +14,8 @@
 #include <linux/platform_device.h>
 #include <linux/serial.h>
 #include <linux/serial_8250.h>
+#include <linux/spi/spi.h>
+#include <linux/spi/spi_s6000.h>
 
 #include <variant/hardware.h>
 #include <variant/dmac.h>

@@ -24,6 +26,7 @@
 #define UART_INTNUM		4
 #define GMAC_INTNUM		5
 #define I2C_INTNUM		6
+#define SPI_INTNUM		11
 
 static const signed char gpio3_irq_mappings[] = {
 	S6_INTC_GPIO(3),

@@ -49,11 +52,17 @@ static const signed char i2c_irq_mappings[] = {
 	-1
 };
 
+static const signed char spi_irq_mappings[] = {
+	S6_INTC_SPI,
+	-1
+};
+
 const signed char *platform_irq_mappings[NR_IRQS] = {
 	[GPIO3_INTNUM] = gpio3_irq_mappings,
 	[UART_INTNUM] = uart_irq_mappings,
 	[GMAC_INTNUM] = gmac_irq_mappings,
 	[I2C_INTNUM] = i2c_irq_mappings,
+	[SPI_INTNUM] = spi_irq_mappings,
 };
 
 static struct plat_serial8250_port serial_platform_data[] = {

@@ -173,6 +182,36 @@ static struct i2c_board_info __initdata s6_i2c_devices[] = {
 	},
 };
 
+static struct resource s6_spi_resource[] = {
+	{
+		.name   = "mem",
+		.start  = (resource_size_t)S6_REG_SPI,
+		.end    = (resource_size_t)S6_REG_SPI + 0x1000 - 1,
+		.flags  = IORESOURCE_MEM,
+	},
+	{
+		.name   = "irq",
+		.start  = (resource_size_t)SPI_INTNUM,
+		.flags  = IORESOURCE_IRQ,
+	},
+};
+
+#define S6_SPI_BUS_NUM	0
+
+static __devinitdata struct s6_spi_platform_data s6_spi_pdata = {
+	.bus_num     = S6_SPI_BUS_NUM,
+	.cs_polarity = 0x00,
+	.clock       = "PCLK",
+};
+
+#define S6_SPI_CS_BOOT_FLASH	0
+#define S6_SPI_CS_BACK_PANEL	1
+#define S6_SPI_CS_EXPANSION	3
+#define S6_SPI_CS_MMC_SLOT	4
+
+static struct spi_board_info __initdata s6_spi_devices[] = {
+};
+
 static struct platform_device platform_devices[] = {
 	{
 		.name = "serial8250",

@@ -195,6 +234,14 @@ static struct platform_device platform_devices[] = {
 			.platform_data = &s6_i2c_pdata,
 		},
 	},
+	{
+		.name = "spi_s6000",
+		.resource = s6_spi_resource,
+		.num_resources = ARRAY_SIZE(s6_spi_resource),
+		.dev = {
+			.platform_data = &s6_spi_pdata,
+		},
+	},
 };
 
 static int __init device_init(void)

@@ -203,6 +250,7 @@ static int __init device_init(void)
 
 	i2c_register_board_info(S6_I2C_BUS_NUM, s6_i2c_devices,
 				ARRAY_SIZE(s6_i2c_devices));
+	spi_register_board_info(s6_spi_devices, ARRAY_SIZE(s6_spi_devices));
 	s6_gmac_resource[5].start = prepare_phy_irq(GPIO_PHY_IRQ);
 
 	for (i = 0; i < ARRAY_SIZE(platform_devices); i++)

arch/xtensa/platforms/s6105/setup.c +4 -1

index e64db1c..5ffa148 100644
@@ -58,7 +58,10 @@ void __init platform_setup(char **cmdline)
 
 void __init platform_init(bp_tag_t *first)
 {
-	s6_setup_gpio(0);
+	s6_setup_gpio(1 << GPIO_SPI_CS0 |
+			1 << GPIO_SPI_CS1 |
+			1 << GPIO_SPI_CS3 |
+			1 << GPIO_SPI_CS4);
 	gpio_request(GPIO_LED1_NGREEN, "led1_green");
 	gpio_request(GPIO_LED1_RED, "led1_red");
 	gpio_direction_output(GPIO_LED1_NGREEN, 1);

Signature · 1 line

1.6.2.107.ge47ee

Daniel Glöckner

author

2009-03-23 15:34 UTC #2 lore raw

PATCH 3/6 xtensa: add spi mmc host to s6105 platform

In reply to Daniel Glöckner

Signed-off-by Daniel Glöckner <[email protected]>

---
 arch/xtensa/platforms/s6105/device.c |   55 ++++++++++++++++++++++++++++++++++
 1 files changed, 55 insertions(+), 0 deletions(-)

arch/xtensa/platforms/s6105/device.c +55 -0

index a7ea916..789448e 100644
@@ -11,9 +11,11 @@
 #include <linux/init.h>
 #include <linux/irq.h>
 #include <linux/phy.h>
+#include <linux/mmc/host.h>
 #include <linux/platform_device.h>
 #include <linux/serial.h>
 #include <linux/serial_8250.h>
+#include <linux/spi/mmc_spi.h>
 #include <linux/spi/spi.h>
 #include <linux/spi/spi_s6000.h>

@@ -209,7 +211,60 @@ static __devinitdata struct s6_spi_platform_data s6_spi_pdata = {
 #define S6_SPI_CS_EXPANSION	3
 #define S6_SPI_CS_MMC_SLOT	4
 
+static int __devinit s6_init_mmc_host(struct device *spi,
+				      irqreturn_t (*handler)(int, void *),
+				      void *mmc)
+{
+	int ret;
+	ret = gpio_request(GPIO_SD_WP, "mmc_wp");
+	if (ret < 0)
+		return ret;
+	ret = gpio_request(GPIO_SD_IRQ, "mmc_irq");
+	if (ret < 0)
+		return ret;
+	ret = gpio_direction_input(GPIO_SD_WP);
+	if (ret < 0)
+		return ret;
+	ret = gpio_direction_input(GPIO_SD_IRQ);
+	if (ret < 0)
+		return ret;
+	ret = gpio_to_irq(GPIO_SD_IRQ);
+	if (ret < 0)
+		return ret;
+	ret = request_irq(ret, handler,
+			  IRQF_TRIGGER_RISING | IRQF_TRIGGER_FALLING,
+			  "mmc_slot", mmc);
+	return ret;
+}
+
+static void __devexit s6_exit_mmc_host(struct device *spi, void *mmc)
+{
+	free_irq(gpio_to_irq(GPIO_SD_IRQ), mmc);
+	gpio_free(GPIO_SD_IRQ);
+	gpio_free(GPIO_SD_WP);
+}
+
+static int s6_mmc_get_ro(struct device *spi)
+{
+	return gpio_get_value(GPIO_SD_WP);
+}
+
+static struct mmc_spi_platform_data s6_spi_mmc_pdata = {
+	.caps = 0,
+	.ocr_mask = MMC_VDD_32_33,
+	.init = s6_init_mmc_host,
+	.exit = __devexit_p(s6_exit_mmc_host),
+	.get_ro = s6_mmc_get_ro,
+};
+
 static struct spi_board_info __initdata s6_spi_devices[] = {
+	{
+		.modalias = "mmc_spi",
+		.platform_data = &s6_spi_mmc_pdata,
+		.bus_num = S6_SPI_BUS_NUM,
+		.chip_select = S6_SPI_CS_MMC_SLOT,
+		.max_speed_hz = 50000000,
+	},
 };
 
 static struct platform_device platform_devices[] = {

Signature · 1 line

1.6.2.107.ge47ee

David Brownell

2009-03-24 20:09 UTC #3 lore raw

Re: [patch 3/6] xtensa: add spi mmc host to s6105 platform

Quoted 1 line · Daniel Glöckner

Signed-off-by Daniel Glöckner <[email protected]>

Looks OK to me. FWIW I don't expect to ack arch patches that just use public interfaces...

Quoted 85 lines

---
 arch/xtensa/platforms/s6105/device.c |   55 ++++++++++++++++++++++++++++++++++
 1 files changed, 55 insertions(+), 0 deletions(-)

arch/xtensa/platforms/s6105/device.c +55 -0

index a7ea916..789448e 100644
@@ -11,9 +11,11 @@
 #include <linux/init.h>
 #include <linux/irq.h>
 #include <linux/phy.h>
+#include <linux/mmc/host.h>
 #include <linux/platform_device.h>
 #include <linux/serial.h>
 #include <linux/serial_8250.h>
+#include <linux/spi/mmc_spi.h>
 #include <linux/spi/spi.h>
 #include <linux/spi/spi_s6000.h>

@@ -209,7 +211,60 @@ static __devinitdata struct s6_spi_platform_data s6_spi_pdata = {
 #define S6_SPI_CS_EXPANSION	3
 #define S6_SPI_CS_MMC_SLOT	4
 
+static int __devinit s6_init_mmc_host(struct device *spi,
+				      irqreturn_t (*handler)(int, void *),
+				      void *mmc)
+{
+	int ret;
+	ret = gpio_request(GPIO_SD_WP, "mmc_wp");
+	if (ret < 0)
+		return ret;
+	ret = gpio_request(GPIO_SD_IRQ, "mmc_irq");
+	if (ret < 0)
+		return ret;
+	ret = gpio_direction_input(GPIO_SD_WP);
+	if (ret < 0)
+		return ret;
+	ret = gpio_direction_input(GPIO_SD_IRQ);
+	if (ret < 0)
+		return ret;
+	ret = gpio_to_irq(GPIO_SD_IRQ);
+	if (ret < 0)
+		return ret;
+	ret = request_irq(ret, handler,
+			  IRQF_TRIGGER_RISING | IRQF_TRIGGER_FALLING,
+			  "mmc_slot", mmc);
+	return ret;
+}
+
+static void __devexit s6_exit_mmc_host(struct device *spi, void *mmc)
+{
+	free_irq(gpio_to_irq(GPIO_SD_IRQ), mmc);
+	gpio_free(GPIO_SD_IRQ);
+	gpio_free(GPIO_SD_WP);
+}
+
+static int s6_mmc_get_ro(struct device *spi)
+{
+	return gpio_get_value(GPIO_SD_WP);
+}
+
+static struct mmc_spi_platform_data s6_spi_mmc_pdata = {
+	.caps = 0,
+	.ocr_mask = MMC_VDD_32_33,
+	.init = s6_init_mmc_host,
+	.exit = __devexit_p(s6_exit_mmc_host),
+	.get_ro = s6_mmc_get_ro,
+};
+
 static struct spi_board_info __initdata s6_spi_devices[] = {
+	{
+		.modalias = "mmc_spi",
+		.platform_data = &s6_spi_mmc_pdata,
+		.bus_num = S6_SPI_BUS_NUM,
+		.chip_select = S6_SPI_CS_MMC_SLOT,
+		.max_speed_hz = 50000000,
+	},
 };
 
 static struct platform_device platform_devices[] = {

Signature · 1 line

1.6.2.107.ge47ee

Daniel Glöckner

author

2009-04-02 10:31 UTC #4 lore raw

Re: [patch 3/6] xtensa: add spi mmc host to s6105 platform

Quoted 2 lines · David Brownell

Looks OK to me. FWIW I don't expect to ack arch patches that just use public interfaces...

Then what do you think of patch 1/6 aka "spi: s6000 spi host driver"?

Daniel

Signature · 6 lines

Dipl.-Math. Daniel Glöckner, emlix GmbH, http://www.emlix.com
Fon +49 551 30664-0, Fax -11, Bahnhofsallee 1b, 37081 Göttingen, Germany
Geschäftsführung: Dr. Uwe Kracke, Dr. Cord Seele, Ust-IdNr.: DE 205 198 055
Sitz der Gesellschaft: Göttingen, Amtsgericht Göttingen HR B 3160

emlix - your embedded linux partner

Daniel Glöckner

author

2009-03-23 15:33 UTC #5 lore raw

PATCH 4/6 xtensa: add m25p80 to s6105 platform

In reply to Daniel Glöckner

The spi_board_info is enclosed in #ifdef CONFIG_MTD_M25P80 to not interfere with the mmc_spi driver if not used. When mmc_spi is fixed to work on a shared bus, this #ifdef can be removed.

The stage2 partition contains the kernels for all processors in the device. In our case a Linux kernel for the SCP core and maybe a non-Linux kernel for the AUX core. The size of the stage2 partition is not hardcoded in the bootloader. It depends on the first few bytes of that partition. Remaining space up to the boot config can be used for other purposes (f.ex. a filesystem).

The boot configuration is expected at address 0xfff800. The flash chip ignores the upper two address bits. Rounding down to sectors then yields an offset of 0x3f0000 for that partition.

Signed-off-by Daniel Glöckner <[email protected]>

---
 arch/xtensa/platforms/s6105/device.c |   47 ++++++++++++++++++++++++++++++++++
 1 files changed, 47 insertions(+), 0 deletions(-)

arch/xtensa/platforms/s6105/device.c +47 -0

index 789448e..bc254ac 100644
@@ -12,9 +12,12 @@
 #include <linux/irq.h>
 #include <linux/phy.h>
 #include <linux/mmc/host.h>
+#include <linux/mtd/mtd.h>
+#include <linux/mtd/partitions.h>
 #include <linux/platform_device.h>
 #include <linux/serial.h>
 #include <linux/serial_8250.h>
+#include <linux/spi/flash.h>
 #include <linux/spi/mmc_spi.h>
 #include <linux/spi/spi.h>
 #include <linux/spi/spi_s6000.h>

@@ -211,6 +214,36 @@ static __devinitdata struct s6_spi_platform_data s6_spi_pdata = {
 #define S6_SPI_CS_EXPANSION	3
 #define S6_SPI_CS_MMC_SLOT	4
 
+static struct mtd_partition s6_spi_flash_partitions[] = {
+	{
+		.name = "bootloader",
+		.size = 0x10000,
+		.offset = 0,
+	},
+	{
+		.name = "stage2",
+		.size = 0x360000,
+		.offset = 0x10000,
+	},
+	{
+		.name = "filesystem",
+		.size = 0x90000,
+		.offset = 0x370000,
+	},
+	{ /* actually 0x800 bytes at 0xfff800 */
+		.name = "bootconfig",
+		.size = 0x10000,
+		.offset = 0x3f0000,
+	}
+};
+
+static struct flash_platform_data s6_spi_flash_pdata = {
+	.name = "m25p80",
+	.parts = s6_spi_flash_partitions,
+	.nr_parts = ARRAY_SIZE(s6_spi_flash_partitions),
+	.type = "m25p32",
+};
+
 static int __devinit s6_init_mmc_host(struct device *spi,
 				      irqreturn_t (*handler)(int, void *),
 				      void *mmc)

@@ -258,6 +291,20 @@ static struct mmc_spi_platform_data s6_spi_mmc_pdata = {
 };
 
 static struct spi_board_info __initdata s6_spi_devices[] = {
+#ifdef CONFIG_MTD_M25P80
+	{
+		.modalias = "m25p80",
+		.platform_data = &s6_spi_flash_pdata,
+		.bus_num = S6_SPI_BUS_NUM,
+		.chip_select = S6_SPI_CS_BOOT_FLASH,
+#ifdef CONFIG_M25PXX_USE_FAST_READ
+		.max_speed_hz = 50000000,
+#else
+		.max_speed_hz = 33000000,
+#endif
+		.mode = SPI_MODE_3
+	},
+#endif
 	{
 		.modalias = "mmc_spi",
 		.platform_data = &s6_spi_mmc_pdata,

Signature · 1 line

1.6.2.107.ge47ee

Daniel Glöckner

author

2009-03-23 15:33 UTC #6 lore raw

PATCH 5/6 xtensa: enable s6000 spi host in s6105_defconfig

In reply to Daniel Glöckner

---
 arch/xtensa/configs/s6105_defconfig |   20 +++++++++++++++++++-
 1 files changed, 19 insertions(+), 1 deletions(-)

arch/xtensa/configs/s6105_defconfig +19 -1

index e398710..02bab6e 100644
@@ -260,6 +260,7 @@ CONFIG_MISC_DEVICES=y
 # EEPROM support
 #
 CONFIG_EEPROM_AT24=y
+# CONFIG_EEPROM_AT25 is not set
 # CONFIG_EEPROM_LEGACY is not set
 # CONFIG_EEPROM_93CX6 is not set
 CONFIG_HAVE_IDE=y

@@ -409,7 +410,22 @@ CONFIG_I2C_S6000=y
 # CONFIG_I2C_DEBUG_ALGO is not set
 # CONFIG_I2C_DEBUG_BUS is not set
 # CONFIG_I2C_DEBUG_CHIP is not set
-# CONFIG_SPI is not set
+CONFIG_SPI=y
+# CONFIG_SPI_DEBUG is not set
+CONFIG_SPI_MASTER=y
+
+#
+# SPI Master Controller Drivers
+#
+# CONFIG_SPI_BITBANG is not set
+# CONFIG_SPI_GPIO is not set
+CONFIG_SPI_S6000=y
+
+#
+# SPI Protocol Masters
+#
+# CONFIG_SPI_SPIDEV is not set
+# CONFIG_SPI_TLE62X0 is not set
 CONFIG_ARCH_REQUIRE_GPIOLIB=y
 CONFIG_GPIOLIB=y
 # CONFIG_DEBUG_GPIO is not set

@@ -433,6 +449,8 @@ CONFIG_GPIOLIB=y
 #
 # SPI GPIO expanders:
 #
+# CONFIG_GPIO_MAX7301 is not set
+# CONFIG_GPIO_MCP23S08 is not set
 # CONFIG_W1 is not set
 # CONFIG_POWER_SUPPLY is not set
 # CONFIG_HWMON is not set

Signature · 1 line

1.6.2.107.ge47ee

Daniel Glöckner

author

2009-03-23 15:37 UTC #7 lore raw

Re: [patch 5/6] xtensa: enable s6000 spi host in s6105_defconfig

arch/xtensa/configs/s6105_defconfig

Quoted 6 lines · Daniel Glöckner

---
 arch/xtensa/configs/s6105_defconfig |   20 +++++++++++++++++++-
 1 files changed, 19 insertions(+), 1 deletions(-)

arch/xtensa/configs/s6105_defconfig +0 -0

index e398710..02bab6e 100644

Signed-off-by Daniel Glöckner <[email protected]>

Signature · 6 lines

Dipl.-Math. Daniel Glöckner, emlix GmbH, http://www.emlix.com
Fon +49 551 30664-0, Fax -11, Bahnhofsallee 1b, 37081 Göttingen, Germany
Geschäftsführung: Dr. Uwe Kracke, Dr. Cord Seele, Ust-IdNr.: DE 205 198 055
Sitz der Gesellschaft: Göttingen, Amtsgericht Göttingen HR B 3160

emlix - your embedded linux partner

Daniel Glöckner

author

2009-03-23 15:34 UTC #8 lore raw

PATCH 6/6 xtensa: enable spi mmc host in s6105_defconfig

In reply to Daniel Glöckner

Signed-off-by Daniel Glöckner <[email protected]>

---
 arch/xtensa/configs/s6105_defconfig |   22 +++++++++++++++++++---
 1 files changed, 19 insertions(+), 3 deletions(-)

arch/xtensa/configs/s6105_defconfig +19 -3

index 02bab6e..c5ea056 100644
@@ -509,7 +509,23 @@ CONFIG_SSB_POSSIBLE=y
 # CONFIG_DISPLAY_SUPPORT is not set
 # CONFIG_SOUND is not set
 # CONFIG_USB_SUPPORT is not set
-# CONFIG_MMC is not set
+CONFIG_MMC=y
+# CONFIG_MMC_DEBUG is not set
+# CONFIG_MMC_UNSAFE_RESUME is not set
+
+#
+# MMC/SD/SDIO Card Drivers
+#
+CONFIG_MMC_BLOCK=y
+# CONFIG_MMC_BLOCK_BOUNCE is not set
+# CONFIG_SDIO_UART is not set
+# CONFIG_MMC_TEST is not set
+
+#
+# MMC/SD/SDIO Host Controller Drivers
+#
+# CONFIG_MMC_SDHCI is not set
+CONFIG_MMC_SPI=y
 # CONFIG_MEMSTICK is not set
 # CONFIG_NEW_LEDS is not set
 # CONFIG_ACCESSIBILITY is not set

@@ -646,9 +662,9 @@ CONFIG_GENERIC_FIND_LAST_BIT=y
 # CONFIG_CRC_CCITT is not set
 # CONFIG_CRC16 is not set
 # CONFIG_CRC_T10DIF is not set
-# CONFIG_CRC_ITU_T is not set
+CONFIG_CRC_ITU_T=y
 # CONFIG_CRC32 is not set
-# CONFIG_CRC7 is not set
+CONFIG_CRC7=y
 # CONFIG_LIBCRC32C is not set
 CONFIG_PLIST=y
 CONFIG_HAS_IOMEM=y

Signature · 1 line

1.6.2.107.ge47ee