Add host_device support to qemu-img.
PATCH RESEND 1/1 Add host_device support to qemu-img.
This patch allows the use a host_device as the destination for "qemu-img convert".
I added a ->bdrv_create function host_device. It merely verifies that the device exists and is large enough.
A check is needed in the qemu-img convert loop to ensure that we write out all 0 sectors to the host_device if they were allocated in the source.
I also made the check against bdrv_is_allocated unconditional, since there is no point in making the block backend write a bunch of zeros just so that we can memcmp them immediately afterwards.
Finally, there is an unrelated fix for a typo in the error message printed if the destination device does not support ->bdrv_create.
Signed-off-by Nolan Leake <nolan <at> sigbus.net>
block-raw-posix.c +36 -0
@@ -1378,11 +1378,47 @@ }#endif /* !linux && !FreeBSD */ +#if defined(__linux__) || defined(__FreeBSD__) +static int hdev_create (const char *filename,int64_t total_size, +const char *backing_file,int flags) +{ +int fd; +int ret =0 ; +struct stat stat_buf; + +if (flags || backing_file) +return -ENOTSUP ; + + fd =open (filename,O_WRONLY |O_BINARY ); +if (fd <0 ) +return -EIO ; + +if (fstat (fd, &stat_buf) <0 ) + ret = -EIO ; +else if (!S_ISBLK (stat_buf.st_mode)) + ret = -EIO ; +else if (lseek (fd,0 ,SEEK_END ) < total_size *512 ) + ret = -ENOSPC ; + +close (fd); +return ret; +} + +#else /* !(linux || freebsd) */ + +static int hdev_create (const char *filename,int64_t total_size, +const char *backing_file,int flags) +{ +return -ENOTSUP ; +} +#endif +BlockDriver bdrv_host_device = { .format_name ="host_device" , .instance_size =sizeof (BDRVRawState), .bdrv_open = hdev_open, .bdrv_close = raw_close, + .bdrv_create = hdev_create, .bdrv_flush = raw_flush, #ifdef CONFIG_AIO
qemu-img.c +14 -15
@@ -493,7 +493,7 @@ ret =bdrv_create (drv, out_filename, total_sectors, out_baseimg, flags);if (ret <0 ) {if (ret == -ENOTSUP ) { -error ("Formatting not supported for file format '%s'" , fmt); +error ("Formatting not supported for file format '%s'" , out_fmt); }else {error ("Error while formatting '%s'" , out_filename); }
@@ -592,19 +592,13 @@if (n > bs_offset + bs_sectors - sector_num) n = bs_offset + bs_sectors - sector_num; -/* If the output image is being created as a copy on write image, -assume that sectors which are unallocated in the input image -are present in both the output's and input's base images (no -need to copy them). */ -if (out_baseimg) { -if (!bdrv_is_allocated (bs[bs_i], sector_num - bs_offset, n, &n1)) { - sector_num += n1; -continue ; - } -/* The next 'n1' sectors are allocated in the input image. Copy -only those as they may be followed by unallocated sectors. */ - n = n1; +if (!bdrv_is_allocated (bs[bs_i], sector_num - bs_offset, n, &n1)) { + sector_num += n1; +continue ; } +/* The next 'n1' sectors are allocated in the input image. Copy +only those as they may be followed by unallocated sectors. */ + n = n1;if (bdrv_read (bs[bs_i], sector_num - bs_offset, buf, n) <0 )error ("error while reading" );
@@ -615,8 +609,13 @@while (n >0 ) {/* If the output image is being created as a copy on write image, copy all sectors even the ones containing only NUL bytes, -because they may differ from the sectors in the base image. */ -if (out_baseimg ||is_allocated_sectors (buf1, n, &n1)) { +because they may differ from the sectors in the base image. + +If the output is to a host device, we also write out +sectors that are entirely 0, since whatever data was +already there is garbage, not 0s. */ +if (drv == &bdrv_host_device || out_baseimg || +is_allocated_sectors (buf1, n, &n1)) {if (bdrv_write (out_bs, sector_num, buf1, n1) <0 )error ("error while writing" ); }