Skip to contentSkip to conversation

How to use Localbus on 5200B w/ 2.6.29.1

DISCUSSION Albrecht Dreß 2 participants 4 messages Apr 27, 2009 – Apr 28, 2009

lore
Share & tools
lore
#0 lore raw

Hi all,

I have a question about the definition of the localbus on the Freescale 5200B (I'm testing with the Lite5200B board) with Kernel 2.6.29.1 which I could not figure out with the docs and the list archives...

When I use 'compatible = "fsl,mpc5200b-lpb";' in the dts file, the localbus and any nodes below it don't show up in /sys/devices.

When I use the following (top-level, not under the soc node) in the dts file

<snip>

localbus {
	compatible = "fsl,lpb";
	#address-cells = <2>;
	#size-cells = <1>;
	reg = <0xf0000300 0x32>;
	ranges = < 0 0 0xfc000000 0x02000000
		   3 0 0xf0020000 0x00010000 >;
	flash@0,0 {
		compatible = "cfi-flash";
		reg = <0 0x0 0x2000000>;	// 32 MB
		bank-width = <1>;		// width in bytes of  
the flash bank
		device-width = <1>;		// one devices on each  
bank
		#size-cells = <1>;
		#address-cells = <1>;
	};

	mydev@3,0 {
		compatible = "mydev";
		reg = <0 0x0 0x100>;		// 256 Bytes, 32 used
		interrupts = <1 3 2>;		// todo - level?
		interrupt-parent = <&mpc5200_pic>;
	};
};

</snip>

I see in /sys/devices

<snip>

# ls -al /sys/devices/
drwxr-xr-x    7 0        0               0 Jan  1 00:00 .
drwxr-xr-x   11 0        0               0 Jan  1 00:00 ..
drwxr-xr-x   31 0        0               0 Jan  1 00:00 f0000000.soc5200
drwxr-xr-x    4 0        0               0 Jan  1 00:00 f0000300.localbus
drwxr-xr-x    2 0        0               0 Jan  1 00:00 platform
drwxr-xr-x    5 0        0               0 Jan  1 00:00 system
drwxr-xr-x    8 0        0               0 Jan  1 00:00 virtual
</snip>

Does this mean that the documentation (and some existing dts files) are inaccurate? What is the proper way to specify the localbus (or, in particular, it's child nodes) on the 5200B?

In /sys/devices/f0000300.localbus, I see

<snip>

# ls -al /sys/devices/f0000300.localbus/
drwxr-xr-x    4 0        0               0 Jan  1 00:00 .
drwxr-xr-x    7 0        0               0 Jan  1 00:00 ..
-r--r--r--    1 0        0            4096 Jan  1 00:00 devspec
drwxr-xr-x    2 0        0               0 Jan  1 00:00 fc000000.flash
drwxr-xr-x    2 0        0               0 Jan  1 00:00 fc000000.mydev
-r--r--r--    1 0        0            4096 Jan  1 00:00 modalias
-r--r--r--    1 0        0            4096 Jan  1 00:00 name
lrwxrwxrwx    1 0        0               0 Jan  1 00:00 subsystem -> ../../bus/of_platform
-rw-r--r--    1 0        0            4096 Jan  1 00:00 uevent
</snip>

which is also confusing, as both devices appear to have the same address? Any idea what goes wrong here?

The flash device itself (mydev isn't present yet...) also doesn't work although mtd is enabled, but that's probably a different problem.

Any help would be really welcome!

Thanks in advance,
Albrecht.

#1 lore raw
Quoted 7 lines · On Mon, Apr 27, 2009 at 11:18 AM, Albrecht Dre=DF <[email protected]>=…

Hi all,

I have a question about the definition of the localbus on the Freescale 5200B (I'm testing with the Lite5200B board) with Kernel 2.6.29.1 which I could not figure out with the docs and the list archives...

When I use 'compatible =3D "fsl,mpc5200b-lpb";' in the dts file, the loca=

lbus

Quoted 1 line

and any nodes below it don't show up in /sys/devices.

For completeness use: compatible =3D "fsl,mpc5200b-lpb","fsl,mpc5200-lpb","simple-bus"; Then it will work.

The kernel doesn't currently bind on the 'b' string, but we put it in the list anyway to completely describe the hardware, just in case it ever becomes important in the future.

[...]

Quoted 2 lines

=A0 =A0 =A0 =A0mydev@3,0 {
=A0 =A0 =A0 =A0 =A0 =A0 =A0 =A0compatible =3D "mydev";

"mydev" should be in the form: "<vendor>,<device>".

Quoted 1 line

=A0 =A0 =A0 =A0 =A0 =A0 =A0 =A0reg =3D <0 0x0 0x100>; =A0 =A0 =A0 =A0 =A0=

=A0// 256 Bytes, 32 used

If this is on CS3, then reg should be:

               reg =3D <3 0x0 0x100>;            // 256 Bytes, 32 used
Quoted 1 line

=A0 =A0 =A0 =A0 =A0 =A0 =A0 =A0interrupts =3D <1 3 2>; =A0 =A0 =A0 =A0 =

=A0 // todo - level?

Quoted 5 lines

=A0 =A0 =A0 =A0 =A0 =A0 =A0 =A0interrupt-parent =3D <&mpc5200_pic>; =A0 =A0 =A0 =A0};
};

# ls -al /sys/devices/f0000300.localbus/
drwxr-xr-x =A0 =A04 0 =A0 =A0 =A0 =A00 =A0 =A0 =A0 =A0 =A0 =A0 =A0 0 Jan =

=A01 00:00 .

Quoted 1 line

drwxr-xr-x =A0 =A07 0 =A0 =A0 =A0 =A00 =A0 =A0 =A0 =A0 =A0 =A0 =A0 0 Jan =

=A01 00:00 ..

Quoted 1 line

-r--r--r-- =A0 =A01 0 =A0 =A0 =A0 =A00 =A0 =A0 =A0 =A0 =A0 =A04096 Jan =

=A01 00:00 devspec

Quoted 1 line

drwxr-xr-x =A0 =A02 0 =A0 =A0 =A0 =A00 =A0 =A0 =A0 =A0 =A0 =A0 =A0 0 Jan =

=A01 00:00 fc000000.flash

Quoted 1 line

drwxr-xr-x =A0 =A02 0 =A0 =A0 =A0 =A00 =A0 =A0 =A0 =A0 =A0 =A0 =A0 0 Jan =

=A01 00:00 fc000000.mydev

Quoted 1 line

-r--r--r-- =A0 =A01 0 =A0 =A0 =A0 =A00 =A0 =A0 =A0 =A0 =A0 =A04096 Jan =

=A01 00:00 modalias

Quoted 1 line

-r--r--r-- =A0 =A01 0 =A0 =A0 =A0 =A00 =A0 =A0 =A0 =A0 =A0 =A04096 Jan =

=A01 00:00 name

Quoted 1 line

lrwxrwxrwx =A0 =A01 0 =A0 =A0 =A0 =A00 =A0 =A0 =A0 =A0 =A0 =A0 =A0 0 Jan =

=A01 00:00 subsystem ->

Quoted 2 lines

../../bus/of_platform
-rw-r--r-- =A0 =A01 0 =A0 =A0 =A0 =A00 =A0 =A0 =A0 =A0 =A0 =A04096 Jan =

=A01 00:00 uevent

Quoted 4 lines

</snip>

which is also confusing, as both devices appear to have the same address? =A0Any idea what goes wrong here?

Because the reg property for mydev is wrong (see above).

g.

--=20
Grant Likely, B.Sc., P.Eng.
Secret Lab Technologies Ltd.

#2 lore raw

Hi Grant:

Am 27.04.09 19:36 schrieb(en) Grant Likely:

Quoted 1 line

For completeness use: compatible = "fsl,mpc5200b-lpb","fsl,mpc5200-lpb","simple-bus"; Then it will work.

I doesn't. I had to add "fsl,lpb", without no localbus nodes show up. The file arch/powerpc/platforms/52xx/mpc52xx_common.c lists only "fsl,lpb" as "compatible". Or did I miss something here?

Quoted 2 lines

If this is on CS3, then reg should be:

               reg = <3 0x0 0x100>;            // 256 Bytes, 32 used

Ouch. Sorry, that was the error. Works perfectly now...

Thanks a lot for your help,
Albrecht.

#3 lore raw
Quoted 8 lines · On Tue, Apr 28, 2009 at 11:55 AM, Albrecht Dre=DF <[email protected]>=…

Hi Grant:

Am 27.04.09 19:36 schrieb(en) Grant Likely:

Quoted 3 lines

For completeness use: compatible =3D "fsl,mpc5200b-lpb","fsl,mpc5200-lpb","simple-bus"; =A0Then it will work.

I doesn't. =A0I had to add "fsl,lpb", without no localbus nodes show up. =

=A0The

Quoted 1 line

file arch/powerpc/platforms/52xx/mpc52xx_common.c lists only "fsl,lpb" =

=A0as

Quoted 1 line

"compatible". =A0Or did I miss something here?

Ah, I guess I didn't merge that fix until 2.6.30. fsl,lpb works for now. What I wrote about is the recommended value for .30 and later, just because it is clearer.

g.

--=20
Grant Likely, B.Sc., P.Eng.
Secret Lab Technologies Ltd.