Skip to contentSkip to conversation

OMAP3: Introduce CONFIG option for power code

PATCH New Dirk Behme 2 participants 8 messages May 6, 2009 – May 12, 2009

lore
Share & tools
lore

Dirk Behme

author
#0 lore raw

PATCH 1/1 OMAP3: Introduce CONFIG option for power code

Some OMAP3 boards need control for external power companion chips. Introduce a CONFIG option for this, to avoid Makefile changes for each board.

---

Compile tested with ./MAKEALL ARM_CORTEX_A8, boot tested on OMAP3 based BeagleBoard.

Note: This patch trys to fix the first comment of

http://lists.denx.de/pipermail/u-boot/2009-April/051383.html

 board/omap3/common/Makefile     |    5 +----
 doc/README.omap3                |   11 +++++++++++
 include/configs/omap3_beagle.h  |    1 +
 include/configs/omap3_overo.h   |    1 +
 include/configs/omap3_pandora.h |    1 +
 include/configs/omap3_zoom1.h   |    1 +
 6 files changed, 16 insertions(+), 4 deletions(-)
doc/README.omap3 +11 -0
Index: u-boot-main/doc/README.omap3
===================================================================
@@ -77,6 +77,17 @@ For all other commands see
 
 help
 
+Custom configs
+==============
+
+CONFIG_OMAP3_POWER
+
+Some OMAP3 boards use external power companion chips to be configured. Enable
+this CONFIG option in your board specific configuration file if your board
+uses such a companion chip.
+
+This enables compilation of board/omap3/common/power.c.
+
 Acknowledgements
 ================
 
board/omap3/common/Makefile +1 -4
Index: u-boot-main/board/omap3/common/Makefile
===================================================================
@@ -29,10 +29,7 @@ endif
 
 LIB	= $(obj)lib$(VENDOR).a
 
-COBJS-$(CONFIG_OMAP3_BEAGLE) += power.o
-COBJS-$(CONFIG_OMAP3_OVERO) += power.o
-COBJS-$(CONFIG_OMAP3_PANDORA) += power.o
-COBJS-$(CONFIG_OMAP3_ZOOM1) += power.o
+COBJS-$(CONFIG_OMAP3_POWER) += power.o
 
 COBJS	:= $(COBJS-y)
 SRCS	:= $(COBJS:.o=.c)
include/configs/omap3_beagle.h +1 -0
Index: u-boot-main/include/configs/omap3_beagle.h
===================================================================
@@ -37,6 +37,7 @@
 #define CONFIG_OMAP34XX		1	/* which is a 34XX */
 #define CONFIG_OMAP3430		1	/* which is in a 3430 */
 #define CONFIG_OMAP3_BEAGLE	1	/* working with BEAGLE */
+#define CONFIG_OMAP3_POWER	1	/* use power code */
 
 #include <asm/arch/cpu.h>		/* get chip and board defs */
 #include <asm/arch/omap3.h>
include/configs/omap3_overo.h +1 -0
Index: u-boot-main/include/configs/omap3_overo.h
===================================================================
@@ -29,6 +29,7 @@
 #define CONFIG_OMAP34XX		1	/* which is a 34XX */
 #define CONFIG_OMAP3430		1	/* which is in a 3430 */
 #define CONFIG_OMAP3_OVERO		1	/* working with overo */
+#define CONFIG_OMAP3_POWER	1	/* use power code */
 
 #include <asm/arch/cpu.h>	/* get chip and board defs */
 #include <asm/arch/omap3.h>
include/configs/omap3_pandora.h +1 -0
Index: u-boot-main/include/configs/omap3_pandora.h
===================================================================
@@ -32,6 +32,7 @@
 #define CONFIG_OMAP34XX		1	/* which is a 34XX */
 #define CONFIG_OMAP3430		1	/* which is in a 3430 */
 #define CONFIG_OMAP3_PANDORA	1	/* working with pandora */
+#define CONFIG_OMAP3_POWER	1	/* use power code */
 
 #include <asm/arch/cpu.h>	/* get chip and board defs */
 #include <asm/arch/omap3.h>
include/configs/omap3_zoom1.h +1 -0
Index: u-boot-main/include/configs/omap3_zoom1.h
===================================================================
@@ -38,6 +38,7 @@
 #define CONFIG_OMAP34XX		1	/* which is a 34XX */
 #define CONFIG_OMAP3430		1	/* which is in a 3430 */
 #define CONFIG_OMAP3_ZOOM1	1	/* working with Zoom MDK Rev1 */
+#define CONFIG_OMAP3_POWER	1	/* use power code */
 
 #include <asm/arch/cpu.h>		/* get chip and board defs */
 #include <asm/arch/omap3.h>
#1 lore raw

PATCH 1/1 OMAP3: Introduce CONFIG option for power code

Quoted 3 lines · Dirk Behme

Some OMAP3 boards need control for external power companion chips. Introduce a CONFIG option for this, to avoid Makefile changes for each board.

please also move it to cpu/arm_cortexa8/omap3/

omap3 and davinci is not a vendor
so common code will need to go to drivers or cpu/<arch>/<soc> for the davinci it's already start to move to it

Best Regards,
J.

Quoted 25 lines

---

Compile tested with ./MAKEALL ARM_CORTEX_A8, boot tested on OMAP3 based BeagleBoard.

Note: This patch trys to fix the first comment of

http://lists.denx.de/pipermail/u-boot/2009-April/051383.html

 board/omap3/common/Makefile     |    5 +----
 doc/README.omap3                |   11 +++++++++++
 include/configs/omap3_beagle.h  |    1 +
 include/configs/omap3_overo.h   |    1 +
 include/configs/omap3_pandora.h |    1 +
 include/configs/omap3_zoom1.h   |    1 +
 6 files changed, 16 insertions(+), 4 deletions(-)

Index: u-boot-main/doc/README.omap3
===================================================================

doc/README.omap3 +0 -0
@@ -77,6 +77,17 @@ For all other commands see
 

doc/README.omap3 For all other commands see · line 87

Quoted 10 lines
doc/README.omap3 +8 -0
 help
 
+Custom configs
+==============
+
+CONFIG_OMAP3_POWER
+
+Some OMAP3 boards use external power companion chips to be configured. Enable
+this CONFIG option in your board specific configuration file if your board
+uses such a companion chip.

could you name it ine the config and the file name

Best Regards,
J.

author
#2 lore raw

PATCH 1/1 OMAP3: Introduce CONFIG option for power code

Dear Jean-Christophe,

Quoted 9 lines · Jean-Christophe PLAGNIOL-VILLARD
Quoted 3 lines · Dirk Behme

Some OMAP3 boards need control for external power companion chips. Introduce a CONFIG option for this, to avoid Makefile changes for each board.

please also move it to cpu/arm_cortexa8/omap3/

omap3 and davinci is not a vendor
so common code will need to go to drivers or cpu/<arch>/<soc>

No, this wouldn't be correct. We used board/omap3/common/ for this intentionally.

We talk about *board* specific code here, it is totally unrelated to <arch> or the <soc> we use. This board specific code configures an OMAP3 (SoC) external companion chip which is on the board (or not). Some boards which share the basic layout have this companion chip, some not. Please note that original config options (we remove with this patch) were the *board* config options (e.g. CONFIG_OMAP3_BEAGLE) to enable the compilation of power.c, too.

Quoted 2 lines

Best Regards,
J.

I nearly missed your comment below because of this ;)

Quoted 26 lines
Quoted 26 lines

---

Compile tested with ./MAKEALL ARM_CORTEX_A8, boot tested on OMAP3 based BeagleBoard.

Note: This patch trys to fix the first comment of

http://lists.denx.de/pipermail/u-boot/2009-April/051383.html

 board/omap3/common/Makefile     |    5 +----
 doc/README.omap3                |   11 +++++++++++
 include/configs/omap3_beagle.h  |    1 +
 include/configs/omap3_overo.h   |    1 +
 include/configs/omap3_pandora.h |    1 +
 include/configs/omap3_zoom1.h   |    1 +
 6 files changed, 16 insertions(+), 4 deletions(-)

Index: u-boot-main/doc/README.omap3
===================================================================

doc/README.omap3 +0 -0
@@ -77,6 +77,17 @@ For all other commands see
 
 help
 
Quoted 9 lines

doc/README.omap3 For all other commands see · line 87

Quoted 8 lines
doc/README.omap3 +8 -0
+Custom configs
+==============
+
+CONFIG_OMAP3_POWER
+
+Some OMAP3 boards use external power companion chips to be configured. Enable
+this CONFIG option in your board specific configuration file if your board
+uses such a companion chip.

could you name it ine the config and the file name

Sorry, I don't understand what you want here. What should I name where? Which file name?

Dirk

#3 lore raw

PATCH 1/1 OMAP3: Introduce CONFIG option for power code

Quoted 8 lines · Dirk Behme

Dear Jean-Christophe,

Quoted 5 lines · Jean-Christophe PLAGNIOL-VILLARD
Quoted 3 lines · Dirk Behme

Some OMAP3 boards need control for external power companion chips. Introduce a CONFIG option for this, to avoid Makefile changes for each board.

Quoted 7 lines
Quoted 4 lines

please also move it to cpu/arm_cortexa8/omap3/

omap3 and davinci is not a vendor
so common code will need to go to drivers or cpu/<arch>/<soc>

No, this wouldn't be correct. We used board/omap3/common/ for this intentionally.

no the current omap3 layout is wrong

it's board/<soc>

but it's supposed to be board/<vendor>

as davinci which is starting to be clean

Quoted 8 lines

We talk about *board* specific code here, it is totally unrelated to <arch> or the <soc> we use. This board specific code configures an OMAP3 (SoC) external companion chip which is on the board (or not). Some boards which share the basic layout have this companion chip, some not. Please note that original config options (we remove with this patch) were the *board* config options (e.g. CONFIG_OMAP3_BEAGLE) to enable the compilation of power.c, too.

as show now the power.c code is shared by a lot's of omap3 boards and as you said it's a power companion for the omap3

so 2 choices
move the code to cpu/omap3 as it's omap3 specific
or to drivers/

Quoted 11 lines
Quoted 10 lines

doc/README.omap3 For all other commands see · line 87

Quoted 9 lines

help
+Custom configs
+==============

doc/README.omap3 +6 -0
+
+CONFIG_OMAP3_POWER
+
+Some OMAP3 boards use external power companion chips to be configured. Enable
+this CONFIG option in your board specific configuration file if your board
+uses such a companion chip.

could you name it ine the config and the file name

Quoted 2 lines

Sorry, I don't understand what you want here. What should I name where? Which file name?

the name of the companion chip as you can use different one

Best Regards,
J.

author
#4 lore raw

PATCH 1/1 OMAP3: Introduce CONFIG option for power code

Dear Jean-Christophe,,

Quoted 8 lines · Jean-Christophe PLAGNIOL-VILLARD
Quoted 7 lines · Dirk Behme

Dear Jean-Christophe,

Quoted 4 lines · Jean-Christophe PLAGNIOL-VILLARD
Quoted 3 lines · Dirk Behme

Some OMAP3 boards need control for external power companion chips. Introduce a CONFIG option for this, to avoid Makefile changes for each board.

Quoted 7 lines
Quoted 6 lines
Quoted 4 lines

please also move it to cpu/arm_cortexa8/omap3/

omap3 and davinci is not a vendor
so common code will need to go to drivers or cpu/<arch>/<soc>

No, this wouldn't be correct. We used board/omap3/common/ for this intentionally.

no

Yes ;) Yes, we use the directory board/omap3/common/ intentionally.

Quoted 1 line

the current omap3 layout is wrong

Sorry, but I can't follow your argumentation here any more. Above, you proposed to move the power code to cpu/arm_cortexa8/omap3/. So I understand the topic we talk about is "where to locate the file power.c". Now, you mention that you think the layout of the directory board/omap3 is wrong (?). This looks like two different discussion topics to me, how is this related?

Quoted 3 lines

it's board/<soc>

but it's supposed to be board/<vendor>

Where do you get this supposing from? Looking at /board I find there e.g.

sbc2410x
sbc405
sbc8240
sbc8260
sbc8349
etc.
etc.

and I don't think these are <vendor>?

Quoted 1 line

as davinci which is starting to be clean

Sorry, but I can't find any board/ti which would be board/<vendor> you mention above. Even not for davinci. I looked into u-boot-arm-master and -next.

But what I can find in both trees are

board/davinci/common
board/davinci/dvevm
board/davinci/schmoogie
board/davinci/<all other Davinci boards>

This is 100% the same layout we use for OMAP3 boards. Looks fine to me.

Quoted 7 lines
Quoted 7 lines

We talk about *board* specific code here, it is totally unrelated to <arch> or the <soc> we use. This board specific code configures an OMAP3 (SoC) external companion chip which is on the board (or not). Some boards which share the basic layout have this companion chip, some not. Please note that original config options (we remove with this patch) were the *board* config options (e.g. CONFIG_OMAP3_BEAGLE) to enable the compilation of power.c, too.

Quoted 5 lines

as show now the power.c code is shared by a lot's of omap3 boards and as you said it's a power companion for the omap3

so 2 choices
move the code to cpu/omap3 as it's omap3 specific

No and no. Above I mentioned why cpu/ is wrong (because it's board related code) and that it's not OMAP3 (SoC) specific. It's (OMAP3) *board* specific.

Quoted 1 line

or to drivers/

Driver makes no sense either, because it's not a driver. Power.c *uses* drivers e.g. I2C (like the board code) to access board components. If you would move power.c to drivers, it would be similar if you would move everything in board/* to drivers.

Please have a look to code in board/davinci/common. These are no drivers, too. It's board code, which normally is in board/davinci/<board>/<board>.c file, but is moved to /common to avoid copy & paste. Same is with OMAP3 power.c code. It was originally in board/omap3/<board>/<board>.c file, but you (correctly) asked to move it to a common place to avoid copy & paste. If you like, we can move it back into <board>.c files ;)

Quoted 10 lines
Quoted 10 lines
Quoted 10 lines

doc/README.omap3 For all other commands see · line 87

Quoted 9 lines

help
+Custom configs
+==============

doc/README.omap3 +6 -0
+
+CONFIG_OMAP3_POWER
+
+Some OMAP3 boards use external power companion chips to be configured. Enable
+this CONFIG option in your board specific configuration file if your board
+uses such a companion chip.

could you name it ine the config and the file name

Quoted 3 lines
Quoted 2 lines

Sorry, I don't understand what you want here. What should I name where? Which file name?

the name of the companion chip as you can use different one

You mean I shall mention the name of the companion chip(s) in the above README.omap3 and the power.c, correct? (just to get this understanding right)

Yes, I can do this. Unfortunately, you can't imagine how clever TI is with selling mainly the same functionality (chips) with different chip names. So most probably there is more than on chip name, and I'm not sure if I will get them right. Most probably only TI marketing department will get this right ;)

Best regards

Dirk

#5 lore raw

PATCH 1/1 OMAP3: Introduce CONFIG option for power code

Quoted 6 lines
Quoted 2 lines

as davinci which is starting to be clean

Sorry, but I can't find any board/ti which would be board/<vendor> you mention above. Even not for davinci. I looked into u-boot-arm-master and -next.

and the code is start to be moved

Quoted 9 lines

But what I can find in both trees are

board/davinci/common
board/davinci/dvevm
board/davinci/schmoogie
board/davinci/<all other Davinci boards>

This is 100% the same layout we use for OMAP3 boards. Looks fine to me.

not to me

Quoted 14 lines
Quoted 8 lines
Quoted 8 lines

We talk about *board* specific code here, it is totally unrelated to <arch> or the <soc> we use. This board specific code configures an OMAP3 (SoC) external companion chip which is on the board (or not). Some boards which share the basic layout have this companion chip, some not. Please note that original config options (we remove with this patch) were the *board* config options (e.g. CONFIG_OMAP3_BEAGLE) to enable the compilation of power.c, too.

Quoted 5 lines

as show now the power.c code is shared by a lot's of omap3 boards and as you said it's a power companion for the omap3

so 2 choices
move the code to cpu/omap3 as it's omap3 specific

Quoted 8 lines

No and no. Above I mentioned why cpu/ is wrong (because it's board related code) and that it's not OMAP3 (SoC) specific. It's (OMAP3) *board* specific.

Quoted 1 line

or to drivers/

Driver makes no sense either, because it's not a driver. Power.c *uses* drivers e.g. I2C (like the board code) to access board components.

no I2C is the communication bus, but you write a i2c drivers to manage the power chips so it's a drivers

Quoted 6 lines

Yes, I can do this. Unfortunately, you can't imagine how clever TI is with selling mainly the same functionality (chips) with different chip names. So most probably there is more than on chip name, and I'm not sure if I will get them right. Most probably only TI marketing department will get this right ;)

why not start with the chip name or the familly name if they can be manage by the same driver

Best Regards,
J.

author
#6 lore raw

PATCH 1/1 OMAP3: Introduce CONFIG option for power code

Dear Jean-Christophe,

Jean-Christophe PLAGNIOL-VILLARD wrote:

[some unanswered questions removed here?]

Quoted 5 lines
Quoted 4 lines
Quoted 1 line

as davinci which is starting to be clean

Sorry, but I can't find any board/ti which would be board/<vendor> you mention above. Even not for davinci. I looked into u-boot-arm-master and -next.

and the code is start to be moved

Sorry, but this confuses me because I can't find this "start" anywhere. So for me this sounds like "I have some (undiscussed) changes in mind or in my local tree, nobody does know about, but every new patch has to care about this (publically unknown) changes" (i.e. this is 'supposed' to be used to use your wording). If this understanding is right, no, this way of dealing with patches and NACKing (?) them doesn't work. If this understanding is wrong, sorry, please correct.

Quoted 9 lines
Quoted 8 lines

But what I can find in both trees are

board/davinci/common
board/davinci/dvevm
board/davinci/schmoogie
board/davinci/<all other Davinci boards>

This is 100% the same layout we use for OMAP3 boards. Looks fine to me.

not to me

Then, as the easiest way of dealing with directory/file moves is doing it directly in your git, the best would be if you do this re-sorting directly.

NACKing a quite trivial patch (this one) because of an existing directory/file layout you don't like, while you requested yourself this change we talk about, and making it a show stopper for adding additional boards [1] like e.g. Matthias' one, sounds somehow strange to me, btw.

[1] http://lists.denx.de/pipermail/u-boot/2009-April/051383.html

Quoted 16 lines
Quoted 16 lines
Quoted 7 lines
Quoted 7 lines

We talk about *board* specific code here, it is totally unrelated to <arch> or the <soc> we use. This board specific code configures an OMAP3 (SoC) external companion chip which is on the board (or not). Some boards which share the basic layout have this companion chip, some not. Please note that original config options (we remove with this patch) were the *board* config options (e.g. CONFIG_OMAP3_BEAGLE) to enable the compilation of power.c, too.

Quoted 5 lines

as show now the power.c code is shared by a lot's of omap3 boards and as you said it's a power companion for the omap3

so 2 choices
move the code to cpu/omap3 as it's omap3 specific

No and no. Above I mentioned why cpu/ is wrong (because it's board related code) and that it's not OMAP3 (SoC) specific. It's (OMAP3) *board* specific.

Quoted 5 lines
Quoted 3 lines
Quoted 1 line

or to drivers/

Driver makes no sense either, because it's not a driver. Power.c *uses* drivers e.g. I2C (like the board code) to access board components.

no I2C is the communication bus, but you write a i2c drivers to manage the power chips so it's a drivers

No. I don't write a driver. I just use a driver. If you want to name code that uses a driver a driver again, then you wouldn't need the board directory any more. Unfortunately, you removed my argumentation regarding this from the previous mail:

-- cut --
.... access board components. If you would move power.c to drivers, it would be similar if you would move everything in board/* to drivers.

Please have a look to code in board/davinci/common. These are no drivers, too. It's board code, which normally is in board/davinci/<board>/<board>.c file, but is moved to /common to avoid copy & paste. Same is with OMAP3 power.c code. It was originally in board/omap3/<board>/<board>.c file, but you (correctly) asked to move it to a common place to avoid copy & paste. If you like, we can move it back into <board>.c files
-- cut --

Additionally, if you don't like the Davinci example, let's take an other one randomly chosen:

http://git.denx.de/cgi-bin/gitweb.cgi?p=u-boot.git;a=blob;f=board/freescale/mpc8568mds/mpc8568mds.c;h=8f991e537df10d8ff48d7783e00bb4aeaa231c79;hb=HEAD

Following your argumentation, for pib_init() you would need an IO expander driver. For pci_init_board() you would need a PCI driver. Both functions are larger than what we talk about here, btw. If you go on with this, you have to create a LED driver for a one liner which enables/disables a LED using a gpio driver. And at the end you will have an empty board directory.

Quoted 6 lines
Quoted 5 lines

Yes, I can do this. Unfortunately, you can't imagine how clever TI is with selling mainly the same functionality (chips) with different chip names. So most probably there is more than on chip name, and I'm not sure if I will get them right. Most probably only TI marketing department will get this right ;)

why not start with the chip name

I think I mentioned above that there are "different chip names". But anyway ...

Quoted 2 lines

or the familly name if they can be manage by
the same driver

(no 'driver' btw)

... as mentioned above I will have a look if I can find some matching naming and send an updated patch with this.

Best regards

Dirk

#7 lore raw

PATCH 1/1 OMAP3: Introduce CONFIG option for power code

Quoted 6 lines · Dirk Behme

Dear Jean-Christophe,

Jean-Christophe PLAGNIOL-VILLARD wrote:

[some unanswered questions removed here?]

Quoted 7 lines
Quoted 5 lines
Quoted 4 lines
Quoted 1 line

as davinci which is starting to be clean

Sorry, but I can't find any board/ti which would be board/<vendor> you mention above. Even not for davinci. I looked into u-boot-arm-master and -next.

and the code is start to be moved

Sorry, but this confuses me because I can't find this "start" anywhere.

davinci: display correct clock info
http://git.denx.de/?p=u-boot/u-boot-arm.git;a=commit;h=5516e87d057c13fce05b6fc6e56cf3f4ddfc36b4
davinci: move psc support board-->cpu
http://git.denx.de/?p=u-boot/u-boot-arm.git;a=commit;h=20bb2384e2b81e77880993134c8f268d59fdfe07

Quoted 51 lines
Quoted 10 lines
Quoted 9 lines

But what I can find in both trees are

board/davinci/common
board/davinci/dvevm
board/davinci/schmoogie
board/davinci/<all other Davinci boards>

This is 100% the same layout we use for OMAP3 boards. Looks fine to me.

not to me

Then, as the easiest way of dealing with directory/file moves is doing it directly in your git, the best would be if you do this re-sorting directly.

NACKing a quite trivial patch (this one) because of an existing directory/file layout you don't like, while you requested yourself this change we talk about, and making it a show stopper for adding additional boards [1] like e.g. Matthias' one, sounds somehow strange to me, btw.

[1] http://lists.denx.de/pipermail/u-boot/2009-April/051383.html

Quoted 17 lines
Quoted 17 lines
Quoted 8 lines
Quoted 8 lines

We talk about *board* specific code here, it is totally unrelated to <arch> or the <soc> we use. This board specific code configures an OMAP3 (SoC) external companion chip which is on the board (or not). Some boards which share the basic layout have this companion chip, some not. Please note that original config options (we remove with this patch) were the *board* config options (e.g. CONFIG_OMAP3_BEAGLE) to enable the compilation of power.c, too.

Quoted 5 lines

as show now the power.c code is shared by a lot's of omap3 boards and as you said it's a power companion for the omap3

so 2 choices
move the code to cpu/omap3 as it's omap3 specific

No and no. Above I mentioned why cpu/ is wrong (because it's board related code) and that it's not OMAP3 (SoC) specific. It's (OMAP3) *board* specific.

Quoted 6 lines
Quoted 4 lines
Quoted 1 line

or to drivers/

Driver makes no sense either, because it's not a driver. Power.c *uses* drivers e.g. I2C (like the board code) to access board components.

no I2C is the communication bus, but you write a i2c drivers to manage the power chips so it's a drivers

No. I don't write a driver. I just use a driver. If you want to name code that uses a driver a driver again, then you wouldn't need the board directory any more. Unfortunately, you removed my argumentation regarding this from the previous mail:

Quoted 6 lines

-- cut --
.... access board components. If you would move power.c to drivers, it would be similar if you would move everything in board/* to drivers.

Please have a look to code in board/davinci/common. These are no drivers, too.

in correct as recently the soc code as device init was move to cpu/arm926ejs/davinci

this only remaining code is the trivial dram_init and the EEProm Mac address management

Quoted 4 lines

If you go on with
this, you have to create a LED driver for a one liner which enables/disables a LED using a gpio driver. And at the end you will have an empty board directory.

it's done for the at91 led drivers to avoid copy&paste and it's in cpu/arm926ejs/at91

Quoted 10 lines
Quoted 7 lines
Quoted 6 lines

Yes, I can do this. Unfortunately, you can't imagine how clever TI is
with selling mainly the same functionality (chips) with different
chip names. So most probably there is more than on chip name, and I'm not sure if I will get them right. Most probably only TI marketing department will get this right ;)

why not start with the chip name

I think I mentioned above that there are "different chip names". But anyway ...

I agree but to simplify it why not use at the beggening the current supported or use chip

Quoted 5 lines
Quoted 3 lines

or the familly name if they can be manage by
the same driver

(no 'driver' btw)

we disagree on the term driver

is this chip is useable for other board than omap3?
if yes (which I suspect correct me if I'm wrong) then it's use is not omap3 specific at all

Quoted 3 lines

... as mentioned above I will have a look if I can find some matching naming and send an updated patch with this.

ok

Best Regards,
J.