Skip to contentSkip to conversation

mac80211: don't wait for channel switch that has happened

PATCH New Johannes Berg 1 participant 2 messages May 8, 2009 mac80211

lore
Share & tools
lore

Johannes Berg

author maintainer
#0 lore raw

PATCH 1/1 mac80211: don't wait for channel switch that has happened

The call to ieee80211_hw_config() is supposed to apply changes synchronously, so once it returns the parameters are applied to the hardware. Thus, there really is no need to delay the probing by the channel switch time again since the channel switch has already happened once we get to this code.

This cuts scanning time from over 7 seconds to about 4 on ar9170, which is due to the number of channels scanned and ar9170's switch time being advertised as 135ms (my test now indicates it is about 77ms with the current driver, but the difference might also be due to using a different machine with different USB controllers).

---
 net/mac80211/scan.c |    3 +--
 1 file changed, 1 insertion(+), 2 deletions(-)
net/mac80211/scan.c +1 -2
@@ -559,8 +559,7 @@ void ieee80211_scan_work(struct work_str
 		if (skip)
 			break;
 
-		next_delay = IEEE80211_PROBE_DELAY +
-			     usecs_to_jiffies(local->hw.channel_change_time);
+		next_delay = IEEE80211_PROBE_DELAY;
 		local->scan_state = SCAN_SEND_PROBE;
 		break;
 	case SCAN_SEND_PROBE:
author maintainer
#1 lore raw

PATCH 1/1 mac80211: improve scan timing

The call to ieee80211_hw_config() is supposed to apply changes synchronously, so once it returns the parameters are applied to the hardware. Thus, there really is no need to delay the probing by the channel switch time again since the channel switch has already happened once we get to this code.

Additionally, there is no need to wait for a NAV update (probe delay) when the channel is passively scanned. Remove that extra time too.

This cuts scanning time from over 7 seconds to under 4 on ar9170, which is due to the number of channels scanned and ar9170's switch time being advertised as 135ms (my test now indicates it is about 77ms with the current driver, but the difference might also be due to using a different machine with different USB controllers).

---
John, this replaces "mac80211: don't wait for channel switch that has happened"

 net/mac80211/scan.c |   31 +++++++++++++++++++++++--------
 1 file changed, 23 insertions(+), 8 deletions(-)
net/mac80211/scan.c +23 -8
@@ -559,24 +559,39 @@ void ieee80211_scan_work(struct work_str
 		if (skip)
 			break;
 
-		next_delay = IEEE80211_PROBE_DELAY +
-			     usecs_to_jiffies(local->hw.channel_change_time);
+		/*
+		 * Probe delay is used to update the NAV, cf. 11.1.3.2.2
+		 * (which unfortunately doesn't say _why_ step a) is done,
+		 * but it waits for the probe delay or until a frame is
+		 * received - and the received frame would update the NAV).
+		 * For now, we do not support waiting until a frame is
+		 * received.
+		 *
+		 * In any case, it is not necessary for a passive scan.
+		 */
+		if (chan->flags & IEEE80211_CHAN_PASSIVE_SCAN ||
+		    !local->scan_req->n_ssids) {
+			next_delay = IEEE80211_PASSIVE_CHANNEL_TIME;
+			break;
+		}
+
+		next_delay = IEEE80211_PROBE_DELAY;
 		local->scan_state = SCAN_SEND_PROBE;
 		break;
 	case SCAN_SEND_PROBE:
-		next_delay = IEEE80211_PASSIVE_CHANNEL_TIME;
-		local->scan_state = SCAN_SET_CHANNEL;
-
-		if (local->scan_channel->flags & IEEE80211_CHAN_PASSIVE_SCAN ||
-		    !local->scan_req->n_ssids)
-			break;
 		for (i = 0; i < local->scan_req->n_ssids; i++)
 			ieee80211_send_probe_req(
 				sdata, NULL,
 				local->scan_req->ssids[i].ssid,
 				local->scan_req->ssids[i].ssid_len,
 				local->scan_req->ie, local->scan_req->ie_len);
+
+		/*
+		 * After sending probe requests, wait for probe responses
+		 * on the channel.
+		 */
 		next_delay = IEEE80211_CHANNEL_TIME;
+		local->scan_state = SCAN_SET_CHANNEL;
 		break;
 	}