Skip to contentSkip to conversation

usb-serial: ftdi: don't dereference NULL pointer

PATCH In review Daniel Mack 3 participants 4 messages May 13, 2009

Subsystems (2)
lore
Share & tools
lore
#0 lore raw

PATCH 1/1 usb-serial: ftdi: don't dereference NULL pointer

The FTDI USB serial driver dereferences its priv structure in ftdi_close() without checking for NULL pointer conditions, see the Oops attached.

The flaw can be reproduced using the following steps:

- connect an FTDI serial converter
- run cu -l ttyUSB0
- disconnect the device
- hit enter in the cu session

The root cause for this is that ftdi_sio_port_remove() is called upon the devices disconnect which sets the private pointer to NULL, but the device remains opened until 'cu' gets a write error and subsequently closes the device.

As we can't call cancel_delayed_work_sync() from ftdi_close() anymore, do that from ftdi_sio_port_remove() now.

Cc Greg KH <[email protected]>
Cc Andrew Morton <[email protected]>
Cc Alan Stern <[email protected]>
Cc USB list <[email protected]>
May 13 11:57:07 jup kernel: [   66.355293] ftdi_sio ttyUSB0: FTDI USB Serial Device converter now disconnected from ttyUSB0
May 13 11:57:07 jup kernel: [   66.382115] drivers/usb/serial/ftdi_sio.c: ftdi_shutdown
May 13 11:57:07 jup kernel: [   66.382119] ftdi_sio 1-4.4:1.0: device disconnected
May 13 11:57:07 jup kernel: [   66.396103] usb 1-4.4:1.0: uevent
May 13 11:57:07 jup kernel: [   66.397329] usb 1-4.4: uevent
May 13 11:57:07 jup kernel: [   66.525618] hub 1-4:1.0: debounce: port 4: total 100ms stable 100ms status 0x100
May 13 11:57:08 jup kernel: [   66.958471] drivers/usb/serial/usb-serial.c: serial_close - port 0
May 13 11:57:08 jup kernel: [   66.958477] drivers/usb/serial/ftdi_sio.c: ftdi_close
May 13 11:57:08 jup kernel: [   66.958491] BUG: unable to handle kernel NULL pointer dereference at 00000080
May 13 11:57:08 jup kernel: [   66.962419] IP: [<c022f054>] del_timer+0xc/0x4e
May 13 11:57:08 jup kernel: [   66.962419] *pde = 00000000
May 13 11:57:08 jup kernel: [   67.000022] Oops: 0000 [#1] PREEMPT SMP
May 13 11:57:08 jup kernel: [   67.000022] last sysfs file: /sys/devices/pci0000:00/0000:00:02.1/usb1/1-4/1-4.4/idProduct
May 13 11:57:08 jup kernel: [   67.000022] Modules linked in: ftdi_sio usbserial ppdev lp cpufreq_userspace cpufreq_conservative cpufreq_powersave cpufreq_stats cpufreq_ondemand
freq_table nfsd exportfs nfs lockd nfs_acl auth_rpcgss sunrpc dm_crypt dm_mod aes_generic cryptoloop loop snd_usb_caiaq snd_rawmidi snd_pcm snd_timer via_rhine snd_page_alloc psm
ouse pcspkr forcedeth mii i2c_nforce2 parport_pc thermal button processor
May 13 11:57:08 jup kernel: [   67.000022]
May 13 11:57:08 jup kernel: [   67.000022] Pid: 2859, comm: cu Tainted: G        W  (2.6.30-rc5 #3) MS-7260
May 13 11:57:08 jup kernel: [   67.000022] EIP: 0060:[<c022f054>] EFLAGS: 00010282 CPU: 1
May 13 11:57:08 jup kernel: [   67.000022] EIP is at del_timer+0xc/0x4e
May 13 11:57:08 jup kernel: [   67.000022] EAX: 00000080 EBX: 00000080 ECX: 00000006 EDX: 00000080
May 13 11:57:08 jup kernel: [   67.000022] ESI: 00000000 EDI: 00000000 EBP: f5829e00 ESP: f5829df4
May 13 11:57:08 jup kernel: [   67.000022]  DS: 007b ES: 007b FS: 00d8 GS: 0033 SS: 0068
May 13 11:57:08 jup kernel: [   67.000022] Process cu (pid: 2859, ti=f5828000 task=f58e92b0 task.ti=f5828000)
May 13 11:57:08 jup kernel: [   67.000022] Stack:
May 13 11:57:08 jup kernel: [   67.000022]  0000000f 000004bd 00000064 f5829e74 c023550f 00000080 00000007 00000068
May 13 11:57:08 jup kernel: [   67.000022]  c0245738 f58e92b0 f58e92b0 00000074 f58e92b0 00000007 f5829e44 c0245738
May 13 11:57:08 jup kernel: [   67.000022]  00000006 f58e92b0 c051d90a f66b817c f5829e54 c024597c f66b8198 f66b8178
May 13 11:57:08 jup kernel: [   67.000022] Call Trace:
May 13 11:57:08 jup kernel: [   67.000022]  [<c023550f>] ? __cancel_work_timer+0x2c/0x190
May 13 11:57:08 jup kernel: [   67.000022]  [<c0245738>] ? mark_held_locks+0x43/0x5b
May 13 11:57:08 jup kernel: [   67.000022]  [<c0245738>] ? mark_held_locks+0x43/0x5b
May 13 11:57:08 jup kernel: [   67.000022]  [<c051d90a>] ? __mutex_unlock_slowpath+0xe9/0x105
May 13 11:57:08 jup kernel: [   67.000022]  [<c024597c>] ? trace_hardirqs_on_caller+0xff/0x120
May 13 11:57:08 jup kernel: [   67.000022]  [<c02459a8>] ? trace_hardirqs_on+0xb/0xd
May 13 11:57:08 jup kernel: [   67.000022]  [<c023567e>] ? cancel_delayed_work_sync+0xb/0xd
May 13 11:57:08 jup kernel: [   67.000022]  [<f97e0c77>] ? ftdi_close+0xbc/0xdb [ftdi_sio]
May 13 11:57:08 jup kernel: [   67.000022]  [<f978f8a2>] ? serial_close+0x7d/0x124 [usbserial]
May 13 11:57:08 jup kernel: [   67.000022]  [<c03cb028>] ? tty_release_dev+0x176/0x3fa
May 13 11:57:08 jup kernel: [   67.000022]  [<c028e16b>] ? vfs_ioctl+0x22/0x69
May 13 11:57:08 jup kernel: [   67.000022]  [<c028e604>] ? do_vfs_ioctl+0x452/0x48b
May 13 11:57:08 jup kernel: [   67.000022]  [<c03cb2be>] ? tty_release+0x12/0x1c
May 13 11:57:08 jup kernel: [   67.000022]  [<c0284097>] ? __fput+0xca/0x175
May 13 11:57:08 jup kernel: [   67.000022]  [<c028415b>] ? fput+0x19/0x1b
May 13 11:57:08 jup kernel: [   67.000022]  [<c0281805>] ? filp_close+0x51/0x5b
May 13 11:57:08 jup kernel: [   67.000022]  [<c0281879>] ? sys_close+0x6a/0xa4
May 13 11:57:08 jup kernel: [   67.000022]  [<c02029c8>] ? sysenter_do_call+0x12/0x36
May 13 11:57:08 jup kernel: [   67.000022] Code: 10 c7 43 04 00 02 20 00 c7 03 00 00 00 00 8b 55 f4 89 c8 e8 da 03 2f 00 59 5b 89 f0 5e c9 c3 55 89 e5 56 31 f6 53 89 c3 83 ec 04
<83> 38 00 74 36 8d 55 f4 31 f6 e8 e4 fd ff ff 8b 13 89 c1 85 d2
May 13 11:57:08 jup kernel: [   67.000022] EIP: [<c022f054>] del_timer+0xc/0x4e SS:ESP 0068:f5829df4
May 13 11:57:08 jup kernel: [   67.000022] CR2: 0000000000000080
May 13 11:57:08 jup kernel: [   67.001177] ---[ end trace 5f3b95b2cbba4930 ]---
---
 drivers/usb/serial/ftdi_sio.c |    8 ++++++--
 1 files changed, 6 insertions(+), 2 deletions(-)
drivers/usb/serial/ftdi_sio.c +6 -2
index 0ab8474..aa9643b 100644
@@ -1492,6 +1492,7 @@ static int ftdi_sio_port_remove(struct usb_serial_port *port)
 	 */
 
 	if (priv) {
+		cancel_delayed_work_sync(&priv->rx_work);
 		usb_set_serial_port_data(port, NULL);
 		kref_put(&priv->kref, ftdi_sio_priv_release);
 	}
@@ -1601,11 +1602,14 @@ static void ftdi_close(struct tty_struct *tty,
 	mutex_unlock(&port->serial->disc_mutex);
 
 	/* cancel any scheduled reading */
-	cancel_delayed_work_sync(&priv->rx_work);
+	if (priv)
+		cancel_delayed_work_sync(&priv->rx_work);
 
 	/* shutdown our bulk read */
 	usb_kill_urb(port->read_urb);
-	kref_put(&priv->kref, ftdi_sio_priv_release);
+
+	if (priv)
+		kref_put(&priv->kref, ftdi_sio_priv_release);
 } /* ftdi_close */
 
 
Signature · 1 line
1.6.2.1
#1 lore raw
Quoted 3 lines · Daniel Mack

The FTDI USB serial driver dereferences its priv structure in ftdi_close() without checking for NULL pointer conditions, see the Oops attached.

Hm, I think this was already resolved with Alan's patch that went in right after 2.6.30-rc5 came out. Can you check Linus's current tree to see if we still need this patch or not?

thanks,

greg k-h

#2 lore raw
Quoted 7 lines · Greg KH
Quoted 3 lines · Daniel Mack

The FTDI USB serial driver dereferences its priv structure in ftdi_close() without checking for NULL pointer conditions, see the Oops attached.

Hm, I think this was already resolved with Alan's patch that went in right after 2.6.30-rc5 came out.

That was a similiar issue, yes. But it occured under different circumstances, not under the condition I described.

Quoted 2 lines

Can you check Linus's current tree to
see if we still need this patch or not?

Is is needed, yes. I'm working on Linus' git as of this morning, so I'm cutting edge mainline and can still perfectly reproduce the problem.

Not anymore with my patch, though.

Daniel

#3 lore raw
In reply to Daniel Mack
Quoted 24 lines · Daniel Mack

The FTDI USB serial driver dereferences its priv structure in ftdi_close() without checking for NULL pointer conditions, see the Oops attached.

The flaw can be reproduced using the following steps:

- connect an FTDI serial converter
- run cu -l ttyUSB0
- disconnect the device
- hit enter in the cu session

The root cause for this is that ftdi_sio_port_remove() is called upon the devices disconnect which sets the private pointer to NULL, but the device remains opened until 'cu' gets a write error and subsequently closes the device.

As we can't call cancel_delayed_work_sync() from ftdi_close() anymore, do that from ftdi_sio_port_remove() now.

drivers/usb/serial/ftdi_sio.c +0 -1
@@ -1601,11 +1602,14 @@ static void ftdi_close(struct tty_struct *tty,
 	mutex_unlock(&port->serial->disc_mutex);
 
 	/* cancel any scheduled reading */
-	cancel_delayed_work_sync(&priv->rx_work);

drivers/usb/serial/ftdi_sio.c static void ftdi_close(struct tty_struct *tty, · line 1613

Quoted 10 lines
drivers/usb/serial/ftdi_sio.c +5 -1
+	if (priv)
+		cancel_delayed_work_sync(&priv->rx_work);
 
 	/* shutdown our bulk read */
 	usb_kill_urb(port->read_urb);
-	kref_put(&priv->kref, ftdi_sio_priv_release);
+
+	if (priv)
+		kref_put(&priv->kref, ftdi_sio_priv_release);
 } /* ftdi_close */

This patch is wrong because it leaks priv: If the pointer is NULL in ftdi_close() then the final kref_put() will never be issued.

How about getting rid of the

		usb_set_serial_port_data(port, NULL);

line in ftdi_sio_port_remove() instead? It's not the greatest solution, but it's the best we can do given the way the usb-serial framework is set up.

It would also be a good idea to get rid of this comment:

	/* all open ports are closed at this point
	 *    (by usbserial.c:__serial_close, which calls ftdi_close)
	 */

since it is completely wrong. And the similar comment preceding ftdi_shutdown().

Moving the cancel_delayed_work_sync() does make sense.

Alan Stern