net-next-2.6: TI DaVinci EMAC driver
Subsystems (2)
PATCH v2 1/1 net-next-2.6: TI DaVinci EMAC driver
Add support for TI DaVinci EMAC driver.
TI DaVinci Ethernet Media Access Controller module is based upon TI CPPI 3.0 DMA engine and supports 10/100 Mbps on all and Gigabit modes on some TI devices. It supports MII/RMII and has up to 8Kbytes of internal descriptor memory. This driver has been working on several TI devices including DM644x, DM646x and DA830 platforms. The specs of this device are available at:
http://www.ti.com/litv/pdf/sprue24a
--- drivers/net/Kconfig | 10 + drivers/net/Makefile | 2 + drivers/net/davinci_emac.c | 2832 ++++++++++++++++++++++++++++++++++++++++++++ 3 files changed, 2844 insertions(+), 0 deletions(-) create mode 100644 drivers/net/davinci_emac.c
drivers/net/Kconfig +10 -0
@@ -926,6 +926,16 @@ config NET_NETX To compile this driver as a module, choose M here. The module will be called netx-eth. +config TI_DAVINCI_EMAC + tristate "TI DaVinci EMAC Support" + depends on ARM && ARCH_DAVINCI + select PHYLIB + help + This driver supports TI's DaVinci Ethernet . + + To compile this driver as a module, choose M here: the module + will be called davinci_emac_driver. This is recommended. + config DM9000 tristate "DM9000 support" depends on ARM || BLACKFIN || MIPS
drivers/net/Makefile +2 -0
@@ -2,6 +2,8 @@ # Makefile for the Linux network (ethercard) device drivers. # +obj-$(CONFIG_TI_DAVINCI_EMAC) += davinci_emac.o + obj-$(CONFIG_E1000) += e1000/ obj-$(CONFIG_E1000E) += e1000e/ obj-$(CONFIG_IBM_NEW_EMAC) += ibm_newemac/
drivers/net/davinci_emac.c new file +2832 -0
2,832 lines not on this page · raw message
Signature · 1 line
1.5.6
From: Chaithrika U S <[email protected]>
Date: Mon, 18 May 2009 07:34:32 -0400
Quoted 9 lines
Add support for TI DaVinci EMAC driver.
TI DaVinci Ethernet Media Access Controller module is based upon TI CPPI 3.0 DMA engine and supports 10/100 Mbps on all and Gigabit modes on some TI devices. It supports MII/RMII and has up to 8Kbytes of internal descriptor memory. This driver has been working on several TI devices including DM644x, DM646x and DA830 platforms. The specs of this device are available at:
http://www.ti.com/litv/pdf/sprue24a
Quoted 3 lines
Signed-off-by Anant Gole <[email protected]>Signed-off-by Kevin Hilman <[email protected]>Signed-off-by Chaithrika U S <[email protected]>
Applied, thanks.
BTW, DECLARE_MAC_BUF(), print_mac() et al. is deprecated, you can simply use the printf format specifier "%pM" to print MAC addresses directly.
David,
Quoted 22 lines
-----Original Message-----
From: David Miller [mailto:[email protected]]
Sent: Tuesday, May 19, 2009 3:50 AM
To: [email protected]
Cc: [email protected]; davinci-linux-open- [email protected]; [email protected]; [email protected]; [email protected]
Subject: Re: [PATCH v2] net-next-2.6: TI DaVinci EMAC driverFrom: Chaithrika U S <[email protected]>
Date: Mon, 18 May 2009 07:34:32 -0400Quoted 4 lines
Add support for TI DaVinci EMAC driver.
TI DaVinci Ethernet Media Access Controller module is based upon TI CPPI 3.0 DMA engine and supports 10/100 Mbps on all and Gigabit
modes on
Quoted 1 line
some TI devices. It supports MII/RMII and has up to 8Kbytes of
internal
Quoted 1 line
descriptor memory. This driver has been working on several TI devices
including
Quoted 1 line
DM644x, DM646x and DA830 platforms. The specs of this device are
Quoted 9 lines
available at:
Quoted 5 lines
http://www.ti.com/litv/pdf/sprue24a
Signed-off-by Anant Gole <[email protected]>Signed-off-by Kevin Hilman <[email protected]>Signed-off-by Chaithrika U S <[email protected]>Applied, thanks.
Thanks.
Quoted 3 lines
BTW,
DECLARE_MAC_BUF(),print_mac()et al. is deprecated, you can simply use the printf format specifier "%pM" to print MAC addresses directly.
OK. Will submit a patch for this.
Regards,
Chaithrika