Skip to contentSkip to conversation

cpu_misc_init support for ARM architectures

PATCH New Prafulla Wadaskar 7 participants 43 messages May 29, 2009 – Jun 28, 2009

Subsystems (5)
lore
Share & tools
lore
#0 lore raw

PATCH 1/1 cpu_misc_init support for ARM architectures

This patch is required for Kirkwood support
may be used by other ARM architectures

---
 include/asm-arm/u-boot-arm.h |    1 +
 lib_arm/board.c              |    4 ++++
 2 files changed, 5 insertions(+), 0 deletions(-)
include/asm-arm/u-boot-arm.h +1 -0
index 76f1ffa..6d2f8bc 100644
@@ -42,6 +42,7 @@ int	cleanup_before_linux(void);
 
 /* cpu/.../arch/cpu.c */
 int	arch_cpu_init(void);
+int	arch_misc_init(void);
 
 /* board/.../... */
 int	board_init(void);
lib_arm/board.c +4 -0
index e081fbc..5c3bfec 100644
@@ -399,6 +399,10 @@ void start_armboot (void)
 
 	console_init_r ();	/* fully init console as a device */
 
+#if defined(CONFIG_ARCH_MISC_INIT)
+	/* miscellaneous arch dependent initialisations */
+	arch_misc_init ();
+#endif
 #if defined(CONFIG_MISC_INIT_R)
 	/* miscellaneous platform dependent initialisations */
 	misc_init_r ();
Signature · 1 line
1.5.3.3
#1 lore raw

PATCH 1/1 cpu_misc_init support for ARM architectures

Quoted 1 line · On Friday 29 May 2009 15:43:30 Prafulla Wadaskar wrote:

+int arch_misc_init(void);

your subject line says cpu_xxx but the source says arch_xxx
-mike
-------------- next part --------------
A non-text attachment was scrubbed...
Name: not available
Type: application/pgp-signature
Size: 836 bytes
Desc: This is a digitally signed message part.
Url : http://lists.denx.de/pipermail/u-boot/attachments/20090529/1b9e4eef/attachment.pgp

#2 lore raw

PATCH 1/1 cpu_misc_init support for ARM architectures

Quoted 11 lines

-----Original Message-----
From: Mike Frysinger [mailto:vapier at gentoo.org]
Sent: Friday, May 29, 2009 9:58 PM
To: u-boot at lists.denx.de
Cc: Prafulla Wadaskar; Manas Saksena; Ronen Shitrit; Nicolas Pitre; Ashish Karkare; Prabhanjan Sarnaik; Lennert Buijtenhek
Subject: Re: [U-Boot] [PATCH] cpu_misc_init support for ARM architectures

Quoted 4 lines
Quoted 1 line · On Friday 29 May 2009 15:43:30 Prafulla Wadaskar wrote:

+int arch_misc_init(void);

your subject line says cpu_xxx but the source says arch_xxx -mike

Hi Mike,
Thanks....
I will correct this
regards..
Prafulla . .

Quoted 1 line
#3 lore raw

PATCH v2 1/1 arch_misc_init support for ARM architectures

This patch is required for Kirkwood support
may be used by other ARM architectures

---
Change log:
v2: Name of the patch corrected to arch_misc_init from cpu_misc_init

 include/asm-arm/u-boot-arm.h |    1 +
 lib_arm/board.c              |    4 ++++
 2 files changed, 5 insertions(+), 0 deletions(-)
include/asm-arm/u-boot-arm.h +1 -0
index 76f1ffa..6d2f8bc 100644
@@ -42,6 +42,7 @@ int	cleanup_before_linux(void);
 
 /* cpu/.../arch/cpu.c */
 int	arch_cpu_init(void);
+int	arch_misc_init(void);
 
 /* board/.../... */
 int	board_init(void);
lib_arm/board.c +4 -0
index e081fbc..5c3bfec 100644
@@ -399,6 +399,10 @@ void start_armboot (void)
 
 	console_init_r ();	/* fully init console as a device */
 
+#if defined(CONFIG_ARCH_MISC_INIT)
+	/* miscellaneous arch dependent initialisations */
+	arch_misc_init ();
+#endif
 #if defined(CONFIG_MISC_INIT_R)
 	/* miscellaneous platform dependent initialisations */
 	misc_init_r ();
Signature · 1 line
1.5.3.3
#5 lore raw

PATCH 1/1 arm: generic cache.h for ARM architectures

In reply to Prafulla Wadaskar

This patch is required for Kirkwood SoC support
may be used by other ARM architectures

---
 include/asm-arm/cache.h |   41 +++++++++++++++++++++++++++++++++++++++++
 1 files changed, 41 insertions(+), 0 deletions(-)
 create mode 100644 include/asm-arm/cache.h
include/asm-arm/cache.h new file +41 -0
new file mode 100644
index 0000000..205b5da
@@ -0,0 +1,41 @@
+/*
+ * (C) Copyright 2009
+ * Marvell Semiconductor <www.marvell.com>
+ * Written-by: Prafulla Wadaskar <[email protected]>
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston,
+ * MA 02110-1301 USA
+ */
+
+#ifndef _ASM_CACHE_H
+#define _ASM_CACHE_H
+
+#include <asm/system.h>
+
+/*
+ * Invalidate L2 Cache using co-proc instruction
+ */
+static inline void invalidate_l2_cache(void)
+{
+	unsigned int val=0;
+
+	asm volatile("mcr p15, 1, %0, c15, c11, 0 @ invl l2 cache"
+		: : "r" (val) : "cc");
+	isb();
+}
+#endif /* _ASM_CACHE_H */
Signature · 1 line
1.5.3.3
#6 lore raw

PATCH 1/1 arm: Kirkwood: Basic SOCs support

Kirkwood family controllers are highly integrated SOCs based on Feroceon-88FR131/Sheeva-88SV131/arm926ejs cpu core.

SOC versions supported:-
1) 88F6281-A0 define CONFIG_KW88F6281_A0
2) 88F6192-A0 define CONFIG_KW88F6192_A0

Other supported features:-
1) get_random_hex() fucntion
2) PCI Express port initialization
3) NS16550 driver support

Contributors:
Yotam Admon <[email protected]>
Michael Blostein <michaelbl at marvell.com

---
 cpu/arm926ejs/kirkwood/Makefile           |   49 +++++
 cpu/arm926ejs/kirkwood/cpu.c              |  324 +++++++++++++++++++++++++++++
 cpu/arm926ejs/kirkwood/dram.c             |   58 +++++
 cpu/arm926ejs/kirkwood/mpp.c              |   80 +++++++
 cpu/arm926ejs/kirkwood/timer.c            |  168 +++++++++++++++
 drivers/serial/serial.c                   |    3 +
 include/asm-arm/arch-kirkwood/cpu.h       |  148 +++++++++++++
 include/asm-arm/arch-kirkwood/kirkwood.h  |   69 ++++++
 include/asm-arm/arch-kirkwood/kw88f6192.h |   37 ++++
 include/asm-arm/arch-kirkwood/kw88f6281.h |   37 ++++
 include/asm-arm/arch-kirkwood/mpp.h       |  303 +++++++++++++++++++++++++++
 11 files changed, 1276 insertions(+), 0 deletions(-)
 create mode 100644 cpu/arm926ejs/kirkwood/Makefile
 create mode 100644 cpu/arm926ejs/kirkwood/cpu.c
 create mode 100644 cpu/arm926ejs/kirkwood/dram.c
 create mode 100644 cpu/arm926ejs/kirkwood/mpp.c
 create mode 100644 cpu/arm926ejs/kirkwood/timer.c
 create mode 100644 include/asm-arm/arch-kirkwood/cpu.h
 create mode 100644 include/asm-arm/arch-kirkwood/kirkwood.h
 create mode 100644 include/asm-arm/arch-kirkwood/kw88f6192.h
 create mode 100644 include/asm-arm/arch-kirkwood/kw88f6281.h
 create mode 100644 include/asm-arm/arch-kirkwood/mpp.h
cpu/arm926ejs/kirkwood/Makefile new file +49 -0
new file mode 100644
index 0000000..b966ea1
@@ -0,0 +1,49 @@
+#
+# (C) Copyright 2009
+# Marvell Semiconductor <www.marvell.com>
+# Written-by: Prafulla Wadaskar <[email protected]>
+#
+# See file CREDITS for list of people who contributed to this
+# project.
+#
+# This program is free software; you can redistribute it and/or
+# modify it under the terms of the GNU General Public License as
+# published by the Free Software Foundation; either version 2 of
+# the License, or (at your option) any later version.
+#
+# This program is distributed in the hope that it will be useful,
+# but WITHOUT ANY WARRANTY; without even the implied warranty of
+# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+# GNU General Public License for more details.
+#
+# You should have received a copy of the GNU General Public License
+# along with this program; if not, write to the Free Software
+# Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston,
+# MA 02110-1301 USA
+#
+
+include $(TOPDIR)/config.mk
+
+LIB	= $(obj)lib$(SOC).a
+
+COBJS-y	= dram.o
+COBJS-y	+= cpu.o
+COBJS-y	+= mpp.o
+COBJS-y	+= timer.o
+
+SRCS	:= $(SOBJS:.o=.S) $(COBJS-y:.o=.c)
+OBJS	:= $(addprefix $(obj),$(SOBJS) $(COBJS-y))
+
+all:	$(obj).depend $(LIB)
+
+$(LIB):	$(OBJS)
+	$(AR) $(ARFLAGS) $@ $(OBJS)
+
+#########################################################################
+
+# defines $(obj).depend target
+include $(SRCTREE)/rules.mk
+
+sinclude $(obj).depend
+
+#########################################################################
cpu/arm926ejs/kirkwood/cpu.c new file +324 -0

324 lines not on this page · raw message

cpu/arm926ejs/kirkwood/dram.c new file +58 -0

58 lines not on this page · raw message

cpu/arm926ejs/kirkwood/mpp.c new file +80 -0

80 lines not on this page · raw message

cpu/arm926ejs/kirkwood/timer.c new file +168 -0

168 lines not on this page · raw message

drivers/serial/serial.c +3 -0
index 966df9a..dd5f332 100644
@@ -27,6 +27,9 @@
 #ifdef CONFIG_NS87308
 #include <ns87308.h>
 #endif
+#ifdef CONFIG_KIRKWOOD
+#include <asm/arch/kirkwood.h>
+#endif
 
 #if defined (CONFIG_SERIAL_MULTI)
 #include <serial.h>
include/asm-arm/arch-kirkwood/cpu.h new file +148 -0

148 lines not on this page · raw message

include/asm-arm/arch-kirkwood/kirkwood.h new file +69 -0

69 lines not on this page · raw message

include/asm-arm/arch-kirkwood/kw88f6192.h new file +37 -0
new file mode 100644
index 0000000..a2b1f96
@@ -0,0 +1,37 @@
+/*
+ * (C) Copyright 2009
+ * Marvell Semiconductor <www.marvell.com>
+ * Written-by: Prafulla Wadaskar <[email protected]>
+ *
+ * Header file for Feroceon CPU core 88FR131 Based KW88F6192 SOC.
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston,
+ * MA 02110-1301 USA
+ */
+
+#ifndef _CONFIG_KW88F6192_H
+#define _CONFIG_KW88F6192_H
+
+/* SOC specific definations */
+#define KW88F6192_REGS_PHYS_BASE	0xf1000000
+#define KW_REGS_PHY_BASE		KW88F6192_REGS_PHYS_BASE
+
+/* TCLK Core Clock defination */
+#define CONFIG_SYS_TCLK	  166000000 /* 166MHz */
+
+#endif /* _CONFIG_KW88F6192_H */
include/asm-arm/arch-kirkwood/kw88f6281.h new file +37 -0
new file mode 100644
index 0000000..9b89b93
@@ -0,0 +1,37 @@
+/*
+ * (C) Copyright 2009
+ * Marvell Semiconductor <www.marvell.com>
+ * Written-by: Prafulla Wadaskar <[email protected]>
+ *
+ * Header file for Feroceon CPU core 88FR131 Based KW88F6281 SOC.
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston,
+ * MA 02110-1301 USA
+ */
+
+#ifndef _ASM_ARCH_KW88F6281_H
+#define _ASM_ARCH_KW88F6281_H
+
+/* SOC specific definations */
+#define KW88F6281_REGS_PHYS_BASE	0xf1000000
+#define KW_REGS_PHY_BASE		KW88F6281_REGS_PHYS_BASE
+
+/* TCLK Core Clock defination*/
+#define CONFIG_SYS_TCLK	  200000000 /* 200MHz */
+
+#endif /* _ASM_ARCH_KW88F6281_H */
include/asm-arm/arch-kirkwood/mpp.h new file +303 -0

303 lines not on this page · raw message

Signature · 1 line
1.5.3.3
#7 lore raw

PATCH 1/1 spi: Add Marvell Kirkwood SPI driver

This patch adds a SPI driver for the Marvell Kirkwood SoC's.

---
 drivers/spi/Makefile                |    1 +
 drivers/spi/kirkwood_spi.c          |  185 +++++++++++++++++++++++++++++++++++
 include/asm-arm/arch-kirkwood/spi.h |   56 +++++++++++
 3 files changed, 242 insertions(+), 0 deletions(-)
 create mode 100644 drivers/spi/kirkwood_spi.c
 create mode 100644 include/asm-arm/arch-kirkwood/spi.h
drivers/spi/Makefile +1 -0
index 1350f3e..7ffa47d 100644
@@ -28,6 +28,7 @@ LIB	:= $(obj)libspi.a
 COBJS-$(CONFIG_ATMEL_DATAFLASH_SPI) += atmel_dataflash_spi.o
 COBJS-$(CONFIG_ATMEL_SPI) += atmel_spi.o
 COBJS-$(CONFIG_BFIN_SPI) += bfin_spi.o
+COBJS-$(CONFIG_KIRKWOOD_SPI) += kirkwood_spi.o
 COBJS-$(CONFIG_MPC8XXX_SPI) += mpc8xxx_spi.o
 COBJS-$(CONFIG_MXC_SPI) += mxc_spi.o
 COBJS-$(CONFIG_SOFT_SPI) += soft_spi.o
drivers/spi/kirkwood_spi.c new file +185 -0

185 lines not on this page · raw message

include/asm-arm/arch-kirkwood/spi.h new file +56 -0

56 lines not on this page · raw message

Signature · 1 line
1.5.3.3
#8 lore raw

PATCH 1/1 nand: Add Marvell Kirkwood NAND driver

This patch adds a NAND driver for the Marvell Kirkwood SoC's.

---
 drivers/mtd/nand/Makefile        |    1 +
 drivers/mtd/nand/kirkwood_nand.c |   81 ++++++++++++++++++++++++++++++++++++++
 2 files changed, 82 insertions(+), 0 deletions(-)
 create mode 100644 drivers/mtd/nand/kirkwood_nand.c
drivers/mtd/nand/Makefile +1 -0
index 471cd6b..766c3f0 100644
@@ -40,6 +40,7 @@ COBJS-$(CONFIG_DRIVER_NAND_BFIN) += bfin_nand.o
 COBJS-$(CONFIG_NAND_DAVINCI) += davinci_nand.o
 COBJS-$(CONFIG_NAND_FSL_ELBC) += fsl_elbc_nand.o
 COBJS-$(CONFIG_NAND_FSL_UPM) += fsl_upm.o
+COBJS-$(CONFIG_NAND_KIRKWOOD) += kirkwood_nand.o
 COBJS-$(CONFIG_NAND_NOMADIK) += nomadik.o
 COBJS-$(CONFIG_NAND_S3C2410) += s3c2410_nand.c
 COBJS-$(CONFIG_NAND_S3C64XX) += s3c64xx.o
drivers/mtd/nand/kirkwood_nand.c new file +81 -0

81 lines not on this page · raw message

Signature · 1 line
1.5.3.3
#9 lore raw

PATCH 1/1 nand: Add Marvell Kirkwood NAND driver

Quoted 4 lines · Prafulla Wadaskar

This patch adds a NAND driver for the Marvell Kirkwood SoC's.

ACK, except for a typo:

drivers/mtd/nand/kirkwood_nand.c line 33

Quoted 5 lines
drivers/mtd/nand/kirkwood_nand.c new file +5 -0
+/* NAND Flash Soc registers */
+struct kwnandf_registers {
+	u32 rd_params;	/* 0x10418 */
+	u32 wr_param;	/* 0x1041c */
+	u8  pag[0x10470 - 0x1041c -4];

s/pag/pad/, presumably. Also s/-4/- 4/.

-Scott

#10 lore raw

PATCH v2 1/1 nand: Add Marvell Kirkwood NAND driver

This patch adds a NAND driver for the Marvell Kirkwood SoC's.

---
Change log:
v2: Typos corrected

 drivers/mtd/nand/Makefile        |    1 +
 drivers/mtd/nand/kirkwood_nand.c |   81 ++++++++++++++++++++++++++++++++++++++
 2 files changed, 82 insertions(+), 0 deletions(-)
 create mode 100644 drivers/mtd/nand/kirkwood_nand.c
drivers/mtd/nand/Makefile +1 -0
index 471cd6b..766c3f0 100644
@@ -40,6 +40,7 @@ COBJS-$(CONFIG_DRIVER_NAND_BFIN) += bfin_nand.o
 COBJS-$(CONFIG_NAND_DAVINCI) += davinci_nand.o
 COBJS-$(CONFIG_NAND_FSL_ELBC) += fsl_elbc_nand.o
 COBJS-$(CONFIG_NAND_FSL_UPM) += fsl_upm.o
+COBJS-$(CONFIG_NAND_KIRKWOOD) += kirkwood_nand.o
 COBJS-$(CONFIG_NAND_NOMADIK) += nomadik.o
 COBJS-$(CONFIG_NAND_S3C2410) += s3c2410_nand.c
 COBJS-$(CONFIG_NAND_S3C64XX) += s3c64xx.o
drivers/mtd/nand/kirkwood_nand.c new file +81 -0

81 lines not on this page · raw message

Signature · 1 line
1.5.3.3
#11 lore raw

PATCH 1/1 nand: Add Marvell Kirkwood NAND driver

In reply to Scott Wood

Hi Scott

I have already posted v2 patch for this change which has only cosmetic change suggested by you. Ref : http://lists.denx.de/pipermail/u-boot/2009-May/053485.html

Since Kirkwood Basic Soc support is pulled in, and if there are no issues pending with this driver. May I request you to pull this on nand/next? Followed by pull request to Wolfgang.

Regards..
Prafulla . .

Quoted 26 lines

-----Original Message-----
From: Scott Wood [mailto:scottwood at freescale.com]
Sent: Saturday, May 30, 2009 1:10 AM
To: Prafulla Wadaskar
Cc: u-boot at lists.denx.de; Manas Saksena; Ronen Shitrit; Nicolas Pitre; Ashish Karkare; Prabhanjan Sarnaik; Lennert Buijtenhek
Subject: Re: [U-Boot] [PATCH] nand: Add Marvell Kirkwood NAND driver

Quoted 4 lines · Prafulla Wadaskar

This patch adds a NAND driver for the Marvell Kirkwood SoC's.

ACK, except for a typo:

drivers/mtd/nand/kirkwood_nand.c line 33

Quoted 5 lines
drivers/mtd/nand/kirkwood_nand.c new file +5 -0
+/* NAND Flash Soc registers */
+struct kwnandf_registers {
+	u32 rd_params;	/* 0x10418 */
+	u32 wr_param;	/* 0x1041c */
+	u8  pag[0x10470 - 0x1041c -4];

s/pag/pad/, presumably. Also s/-4/- 4/.

-Scott

#12 lore raw

PATCH 1/1 net: Add Marvell Kirkwood gigabit ethernet driver

In reply to Prafulla Wadaskar

This patch adds a egiga driver for the Marvell Kirkwood SoC's.

Contributors:
Yotam Admon <[email protected]>
Michael Blostein <michaelbl at marvell.com

---
 drivers/net/Makefile         |    1 +
 drivers/net/kirkwood_egiga.c |  674 ++++++++++++++++++++++++++++++++++++++++++
 drivers/net/kirkwood_egiga.h |  561 +++++++++++++++++++++++++++++++++++
 include/netdev.h             |    1 +
 4 files changed, 1237 insertions(+), 0 deletions(-)
 create mode 100644 drivers/net/kirkwood_egiga.c
 create mode 100644 drivers/net/kirkwood_egiga.h
drivers/net/Makefile +1 -0
index a360a50..f0c5654 100644
@@ -40,6 +40,7 @@ COBJS-$(CONFIG_ENC28J60) += enc28j60.o
 COBJS-$(CONFIG_FSLDMAFEC) += fsl_mcdmafec.o mcfmii.o
 COBJS-$(CONFIG_GRETH) += greth.o
 COBJS-$(CONFIG_INCA_IP_SWITCH) += inca-ip_sw.o
+COBJS-$(CONFIG_KIRKWOOD_EGIGA) += kirkwood_egiga.o
 COBJS-$(CONFIG_DRIVER_KS8695ETH) += ks8695eth.o
 COBJS-$(CONFIG_DRIVER_LAN91C96) += lan91c96.o
 COBJS-$(CONFIG_MACB) += macb.o
drivers/net/kirkwood_egiga.c new file +674 -0

674 lines not on this page · raw message

drivers/net/kirkwood_egiga.h new file +561 -0

561 lines not on this page · raw message

include/netdev.h +1 -0
index f37b6ae..3a59f4e 100644
@@ -52,6 +52,7 @@ int fec_initialize (bd_t *bis);
 int greth_initialize(bd_t *bis);
 void gt6426x_eth_initialize(bd_t *bis);
 int inca_switch_initialize(bd_t *bis);
+int kirkwood_egiga_initialize(bd_t *bis);
 int macb_eth_initialize(int id, void *regs, unsigned int phy_addr);
 int mcdmafec_initialize(bd_t *bis);
 int mcffec_initialize(bd_t *bis);
Signature · 1 line
1.5.3.3
#13 lore raw

PATCH 1/1 Marvell MV88F6281GTW_GE Board support

This is Marvell's 88F6281_A0 based custom board developed for wireless access point product

This patch is tested for-
1. Boot from DRAM/SPI flash/NFS
2. File transfer using tftp and loadb
3. SPI flash read/write/erase
4. Booting Linux kernel and RFS from SPI flash

---
 MAKEALL                                         |    1 +
 Makefile                                        |    3 +
 board/Marvell/mv88f6281gtw_ge/Makefile          |   51 ++++++
 board/Marvell/mv88f6281gtw_ge/config.mk         |   25 +++
 board/Marvell/mv88f6281gtw_ge/mv88f6281gtw_ge.c |  141 +++++++++++++++++
 board/Marvell/mv88f6281gtw_ge/mv88f6281gtw_ge.h |   36 +++++
 include/configs/mv88f6281gtw_ge.h               |  188 +++++++++++++++++++++++
 7 files changed, 445 insertions(+), 0 deletions(-)
 create mode 100644 board/Marvell/mv88f6281gtw_ge/Makefile
 create mode 100644 board/Marvell/mv88f6281gtw_ge/config.mk
 create mode 100644 board/Marvell/mv88f6281gtw_ge/mv88f6281gtw_ge.c
 create mode 100644 board/Marvell/mv88f6281gtw_ge/mv88f6281gtw_ge.h
 create mode 100644 include/configs/mv88f6281gtw_ge.h
MAKEALL +1 -0
index c98d03a..6719d7b 100755
@@ -505,6 +505,7 @@ LIST_ARM9="			\
 	cp946es			\
 	cp966			\
 	lpd7a400		\
+	mv88f6281gtw_ge		\
 	mx1ads			\
 	mx1fs2			\
 	netstar			\
Makefile +3 -0
index 81a5cd0..8144ecd 100644
@@ -2808,6 +2808,9 @@ lpd7a400_config \
 lpd7a404_config:	unconfig
 	@$(MKCONFIG) $(@:_config=) arm lh7a40x lpd7a40x
 
+mv88f6281gtw_ge_config: unconfig
+	@$(MKCONFIG) $(@:_config=) arm arm926ejs $(@:_config=) Marvell kirkwood
+
 mx1ads_config	:	unconfig
 	@$(MKCONFIG) $(@:_config=) arm arm920t mx1ads NULL imx
 
board/Marvell/mv88f6281gtw_ge/Makefile new file +51 -0

51 lines not on this page · raw message

board/Marvell/mv88f6281gtw_ge/config.mk new file +25 -0
new file mode 100644
index 0000000..fb29a1b
@@ -0,0 +1,25 @@
+#
+# (C) Copyright 2009
+# Marvell Semiconductor <www.marvell.com>
+# Written-by: Prafulla Wadaskar <[email protected]>
+#
+# See file CREDITS for list of people who contributed to this
+# project.
+#
+# This program is free software; you can redistribute it and/or
+# modify it under the terms of the GNU General Public License as
+# published by the Free Software Foundation; either version 2 of
+# the License, or (at your option) any later version.
+#
+# This program is distributed in the hope that it will be useful,
+# but WITHOUT ANY WARRANTY; without even the implied warranty of
+# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+# GNU General Public License for more details.
+#
+# You should have received a copy of the GNU General Public License
+# along with this program; if not, write to the Free Software
+# Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston,
+# MA 02110-1301 USA
+#
+
+TEXT_BASE = 0x00600000
board/Marvell/mv88f6281gtw_ge/mv88f6281gtw_ge.c new file +141 -0

141 lines not on this page · raw message

board/Marvell/mv88f6281gtw_ge/mv88f6281gtw_ge.h new file +36 -0
new file mode 100644
index 0000000..fb0e571
@@ -0,0 +1,36 @@
+/*
+ * (C) Copyright 2009
+ * Marvell Semiconductor <www.marvell.com>
+ * Written-by: Prafulla Wadaskar <[email protected]>
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston,
+ * MA 02110-1301 USA
+ */
+
+#ifndef __MV88F6281GTW_GE_H
+#define __MV88F6281GTW_GE_H
+
+#define MV88F6281GTW_GE_OE_LOW		(~((1 << 7) | (1 << 12) \
+					  |(1 << 20) | (1 << 21)))	/*enable GLED,RLED */
+#define MV88F6281GTW_GE_OE_HIGH		(~((1 << 4)|(1 << 6)|(1 << 7)|(1 << 12) \
+					  |(1 << 13)|(1 << 16)|(1 << 17)))
+#define MV88F6281GTW_GE_OE_VAL_LOW	(1 << 20)	/*make GLED on */
+#define MV88F6281GTW_GE_OE_VAL_HIGH	((1 << 6)|(1 << 13)|(1 << 16)|(1 << 17))
+
+
+#endif /* __MV88F6281GTW_GE_H */
include/configs/mv88f6281gtw_ge.h new file +188 -0

188 lines not on this page · raw message

Signature · 1 line
1.5.3.3
#14 lore raw

PATCH 1/1 Marvell Sheevaplug Board support

Reference:
http://plugcomputer.org/
http://openplug.org/plugwiki/index.php/Das_U-boot_plug_support

This patch is tested for-
1. Boot from DRAM/NAND flash
2. File transfer using tftp
3. NAND flash read/write/erase
4. Linux kernel and RFS Boot from NAND

---
 MAKEALL                               |    1 +
 Makefile                              |    4 +-
 board/Marvell/sheevaplug/Makefile     |   51 +++++++++
 board/Marvell/sheevaplug/config.mk    |   25 +++++
 board/Marvell/sheevaplug/sheevaplug.c |  135 +++++++++++++++++++++++
 board/Marvell/sheevaplug/sheevaplug.h |   37 +++++++
 include/configs/sheevaplug.h          |  192 +++++++++++++++++++++++++++++++++
 7 files changed, 444 insertions(+), 1 deletions(-)
 create mode 100644 board/Marvell/sheevaplug/Makefile
 create mode 100644 board/Marvell/sheevaplug/config.mk
 create mode 100644 board/Marvell/sheevaplug/sheevaplug.c
 create mode 100644 board/Marvell/sheevaplug/sheevaplug.h
 create mode 100644 include/configs/sheevaplug.h
MAKEALL +1 -0
index 6719d7b..e3d33cb 100755
@@ -144,6 +144,7 @@ LIST_8xx="		\
 	RPXlite		\
 	RPXlite_DW	\
 	RRvision	\
+	sheevaplug	\
 	SM850		\
 	spc1920		\
 	SPD823TS	\
Makefile +3 -1
index 8144ecd..39b3367 100644
@@ -1122,6 +1122,9 @@ RRvision_LCD_config:	unconfig
 	@echo "#define CONFIG_SHARP_LQ104V7DS01" >>$(obj)include/config.h
 	@$(MKCONFIG) -a RRvision ppc mpc8xx RRvision
 
+sheevaplug_config: unconfig
+	@$(MKCONFIG) $(@:_config=) arm arm926ejs $(@:_config=) Marvell kirkwood
+
 SM850_config	:	unconfig
 	@$(MKCONFIG) $(@:_config=) ppc mpc8xx tqm8xx tqc
 
@@ -3110,7 +3113,6 @@ omap2420h4_config	: unconfig
 qong_config		: unconfig
 	@$(MKCONFIG) $(@:_config=) arm arm1136 qong davedenx mx31
 
-
 #########################################################################
 ## ARM1176 Systems
 #########################################################################
board/Marvell/sheevaplug/Makefile new file +51 -0

51 lines not on this page · raw message

board/Marvell/sheevaplug/config.mk new file +25 -0
new file mode 100644
index 0000000..fb29a1b
@@ -0,0 +1,25 @@
+#
+# (C) Copyright 2009
+# Marvell Semiconductor <www.marvell.com>
+# Written-by: Prafulla Wadaskar <[email protected]>
+#
+# See file CREDITS for list of people who contributed to this
+# project.
+#
+# This program is free software; you can redistribute it and/or
+# modify it under the terms of the GNU General Public License as
+# published by the Free Software Foundation; either version 2 of
+# the License, or (at your option) any later version.
+#
+# This program is distributed in the hope that it will be useful,
+# but WITHOUT ANY WARRANTY; without even the implied warranty of
+# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+# GNU General Public License for more details.
+#
+# You should have received a copy of the GNU General Public License
+# along with this program; if not, write to the Free Software
+# Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston,
+# MA 02110-1301 USA
+#
+
+TEXT_BASE = 0x00600000
board/Marvell/sheevaplug/sheevaplug.c new file +135 -0

135 lines not on this page · raw message

board/Marvell/sheevaplug/sheevaplug.h new file +37 -0
new file mode 100644
index 0000000..45bfeca
@@ -0,0 +1,37 @@
+/*
+ * (C) Copyright 2009
+ * Marvell Semiconductor <www.marvell.com>
+ * Written-by: Prafulla Wadaskar <[email protected]>
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston,
+ * MA 02110-1301 USA
+ */
+
+#ifndef __SHEEVAPLUG_H
+#define __SHEEVAPLUG_H
+
+#ifndef MACH_TYPE_SHEEVAPLUG
+#define MACH_TYPE_SHEEVAPLUG	2097
+#endif
+
+#define SHEEVAPLUG_OE_LOW		(~(0))
+#define SHEEVAPLUG_OE_HIGH		(~(0))
+#define SHEEVAPLUG_OE_VAL_LOW		(1 << 29)	/* USB_PWEN low */
+#define SHEEVAPLUG_OE_VAL_HIGH		(1 << 17)	/* LED pin high */
+
+#endif /* __SHEEVAPLUG_H */
include/configs/sheevaplug.h new file +192 -0

192 lines not on this page · raw message

Signature · 1 line
1.5.3.3
#15 lore raw

PATCH 1/1 Marvell Sheevaplug Board support

Please do not review/accept this patch, I have send v2 for this. Sorry for inconvenience

Regards..
Prafulla . .

Quoted 27 lines

-----Original Message-----
From: Prafulla Wadaskar [mailto:prafulla at marvell.com]
Sent: Saturday, May 30, 2009 1:14 AM
To: u-boot at lists.denx.de
Cc: Nicolas Pitre; Manas Saksena; Lennert Buijtenhek; Prabhanjan Sarnaik; Ronen Shitrit; Ashish Karkare; Prafulla Wadaskar
Subject: [PATCH] Marvell Sheevaplug Board support

Reference:
http://plugcomputer.org/
http://openplug.org/plugwiki/index.php/Das_U-boot_plug_support

This patch is tested for-
1. Boot from DRAM/NAND flash
2. File transfer using tftp
3. NAND flash read/write/erase
4. Linux kernel and RFS Boot from NAND

---
 MAKEALL                               |    1 +
 Makefile                              |    4 +-
 board/Marvell/sheevaplug/Makefile     |   51 +++++++++
 board/Marvell/sheevaplug/config.mk    |   25 +++++
 board/Marvell/sheevaplug/sheevaplug.c |  135 +++++++++++++++++++++++
 board/Marvell/sheevaplug/sheevaplug.h |   37 +++++++
 include/configs/sheevaplug.h          |  192 
#16 lore raw

PATCH 1/1 Marvell Sheevaplug Board support

In reply to Prafulla Wadaskar

Dear Prafulla Wadaskar,

Quoted 11 lines · In message <[email protected]> you wrote:

Reference:
http://plugcomputer.org/
http://openplug.org/plugwiki/index.php/Das_U-boot_plug_support

This patch is tested for-
1. Boot from DRAM/NAND flash
2. File transfer using tftp
3. NAND flash read/write/erase
4. Linux kernel and RFS Boot from NAND

Quoted 14 lines
---
 MAKEALL                               |    1 +
 Makefile                              |    4 +-
 board/Marvell/sheevaplug/Makefile     |   51 +++++++++
 board/Marvell/sheevaplug/config.mk    |   25 +++++
 board/Marvell/sheevaplug/sheevaplug.c |  135 +++++++++++++++++++++++
 board/Marvell/sheevaplug/sheevaplug.h |   37 +++++++
 include/configs/sheevaplug.h          |  192 +++++++++++++++++++++++++++++++++
 7 files changed, 444 insertions(+), 1 deletions(-)
 create mode 100644 board/Marvell/sheevaplug/Makefile
 create mode 100644 board/Marvell/sheevaplug/config.mk
 create mode 100644 board/Marvell/sheevaplug/sheevaplug.c
 create mode 100644 board/Marvell/sheevaplug/sheevaplug.h
 create mode 100644 include/configs/sheevaplug.h

Entry in MAINTAINERS missing.

...

include/configs/sheevaplug.h line 100

Quoted 12 lines
include/configs/sheevaplug.h new file +12 -0
+/*
+ * Commands configuration
+ */
+#define CONFIG_CMD_ENV
+#define CONFIG_CMD_RUN
+#define CONFIG_CMD_LOADB
+#define CONFIG_CMD_NET
+#define CONFIG_CMD_AUTOSCRIPT
+#define CONFIG_CMD_MEMORY
+#define CONFIG_CMD_BOOTD
+#define CONFIG_CMD_SAVEENV
+#define CONFIG_CMD_NAND

Please sort.

...

include/configs/sheevaplug.h line 141

Quoted 2 lines
include/configs/sheevaplug.h new file +2 -0
+#define CONFIG_MTDPARTS			"orion_nand:512k(uboot),"	\
+	"1m at 4m(psm), 3m at 1m(kernel),13m at 5m(rootfs) rw\0"

Do you really want to have such an unusal and unexpectad setup?

include/configs/sheevaplug.h line 175

Quoted 6 lines
include/configs/sheevaplug.h new file +6 -0
+/*
+ * Ethernet Driver configuration
+ */
+#ifdef CONFIG_CMD_NET
+#define CONFIG_CMD_DHCP
+#define CONFIG_CMD_PING

I recommend to keep command definitions close together. Move up?

include/configs/sheevaplug.h line 184

Quoted 9 lines
include/configs/sheevaplug.h new file +9 -0
+#define CONFIG_NETCONSOLE	/* include NetConsole support   */
+#define CONFIG_NET_MULTI	/* specify more that one ports available */
+#define	CONFIG_MII		/* expose smi ove miiphy interface */
+#define CONFIG_KIRKWOOD_EGIGA	/* Enable kirkwood Gbe Controller Driver */
+#define CONFIG_SYS_FAULT_ECHO_LINK_DOWN	/* detect link using phy */
+#define CONFIG_KIRKWOOD_EGIGA_PORTS	{1,0}	/* enable port 0 only */
+#define CONFIG_PHY_BASE_ADR	0
+#define CONFIG_ENV_OVERWRITE	/* ethaddr can be reprogrammed */
+#endif /* CONFIG_CMD_NET */

Best regards,

Wolfgang Denk

Signature · 5 lines
DENX Software Engineering GmbH,     MD: Wolfgang Denk & Detlev Zundel
HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany
Phone: (+49)-8142-66989-10 Fax: (+49)-8142-66989-80 Email: wd at denx.de
Perl already has an IDE.  It's called Unix.
                      -- Tom Christiansen in 375bd509 at cs.colorado.edu
#17 lore raw

PATCH 1/1 Marvell MV88F6281GTW_GE Board support

In reply to Prafulla Wadaskar

Dear Prafulla Wadaskar,

Quoted 11 lines · In message <[email protected]> you wrote:

This is Marvell's 88F6281_A0 based custom board developed for wireless access point product

This patch is tested for-
1. Boot from DRAM/SPI flash/NFS
2. File transfer using tftp and loadb
3. SPI flash read/write/erase
4. Booting Linux kernel and RFS from SPI flash

Quoted 14 lines
---
 MAKEALL                                         |    1 +
 Makefile                                        |    3 +
 board/Marvell/mv88f6281gtw_ge/Makefile          |   51 ++++++
 board/Marvell/mv88f6281gtw_ge/config.mk         |   25 +++
 board/Marvell/mv88f6281gtw_ge/mv88f6281gtw_ge.c |  141 +++++++++++++++++
 board/Marvell/mv88f6281gtw_ge/mv88f6281gtw_ge.h |   36 +++++
 include/configs/mv88f6281gtw_ge.h               |  188 +++++++++++++++++++++++
 7 files changed, 445 insertions(+), 0 deletions(-)
 create mode 100644 board/Marvell/mv88f6281gtw_ge/Makefile
 create mode 100644 board/Marvell/mv88f6281gtw_ge/config.mk
 create mode 100644 board/Marvell/mv88f6281gtw_ge/mv88f6281gtw_ge.c
 create mode 100644 board/Marvell/mv88f6281gtw_ge/mv88f6281gtw_ge.h
 create mode 100644 include/configs/mv88f6281gtw_ge.h

Entry in MAINTAINERS file is missing.

Quoted 5 lines
include/configs/mv88f6281gtw_ge.h new file +0 -0
new file mode 100644
index 0000000..8735b9e

...

include/configs/mv88f6281gtw_ge.h line 101

Quoted 12 lines
include/configs/mv88f6281gtw_ge.h new file +12 -0
+/*
+ * Commands configuration
+ */
+#define CONFIG_CMD_ENV
+#define CONFIG_CMD_RUN
+#define CONFIG_CMD_LOADB
+#define CONFIG_CMD_NET
+#define CONFIG_CMD_AUTOSCRIPT
+#define CONFIG_CMD_MEMORY
+#define CONFIG_CMD_BOOTD
+#define CONFIG_CMD_SAVEENV
+#define CONFIG_CMD_SF

Please sort such lists.

...

include/configs/mv88f6281gtw_ge.h line 138

Quoted 2 lines
include/configs/mv88f6281gtw_ge.h new file +2 -0
+#define CONFIG_MTDPARTS			"spi0.0:512k(uboot),"	\
+	"512k at 512k(psm), 2m at 1m(kernel),13m at 3m(rootfs)\0"

For readability, you might want to omit the redundant offet values here.

Best regards,

Wolfgang Denk

Signature · 5 lines
DENX Software Engineering GmbH,     MD: Wolfgang Denk & Detlev Zundel
HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany
Phone: (+49)-8142-66989-10 Fax: (+49)-8142-66989-80 Email: wd at denx.de
You may call me by my name, Wirth, or by my value, Worth.
- Nicklaus Wirth
#18 lore raw

PATCH 1/1 net: Add Marvell Kirkwood gigabit ethernet driver

In reply to Prafulla Wadaskar
Quoted 9 lines · Prafulla Wadaskar

This patch adds a egiga driver for the Marvell Kirkwood SoC's.

Contributors:
Yotam Admon <[email protected]>
Michael Blostein <[email protected]

Ben if it's ok for you I'll apply with rest of the series

Best Regards,
J.

#19 lore raw

PATCH 1/1 net: Add Marvell Kirkwood gigabit ethernet driver

Quoted 8 lines · Jean-Christophe PLAGNIOL-VILLARD
Quoted 6 lines · Prafulla Wadaskar

This patch adds a egiga driver for the Marvell Kirkwood SoC's.

Contributors:
Yotam Admon <[email protected]>
Michael Blostein <[email protected]

Quoted 9 lines
Quoted 4 lines

Ben if it's ok for you I'll apply with rest of the series

Best Regards,
J.

I'll look at it this weekend.

regards,
Ben

#20 lore raw

PATCH 1/1 net: Add Marvell Kirkwood gigabit ethernet driver

Quoted 25 lines

-----Original Message-----
From: Ben Warren [mailto:biggerbadderben at gmail.com]
Sent: Saturday, May 30, 2009 4:51 AM
To: Jean-Christophe PLAGNIOL-VILLARD
Cc: Prafulla Wadaskar; u-boot at lists.denx.de; Manas Saksena; Ronen Shitrit; Nicolas Pitre; Ashish Karkare; Prabhanjan Sarnaik; Lennert Buijtenhek
Subject: Re: [U-Boot] [PATCH] net: Add Marvell Kirkwood gigabit ethernet driver

Quoted 12 lines · Jean-Christophe PLAGNIOL-VILLARD
Quoted 10 lines · Prafulla Wadaskar

This patch adds a egiga driver for the Marvell Kirkwood SoC's.

Contributors:
Yotam Admon <[email protected]>
Michael Blostein <[email protected]

Quoted 6 lines
Quoted 5 lines

Ben if it's ok for you I'll apply with rest of the series

Best Regards,
J.

I'll look at it this weekend.

Hi Ben,
I have put the huge efforts to tune it specially for code size reduction. Whereas I have lost only network statistics and packet info print debugging features. Now it looks more simpler and cleaner :-)
Hopefully it will stand as per your suggestions.

See the difference
New driver..

 drivers/net/Makefile         |    1 +
 drivers/net/kirkwood_egiga.c |  674 ++++++++++++++++++++++++++++++++++++++++++
 drivers/net/kirkwood_egiga.h |  561 +++++++++++++++++++++++++++++++++++
 include/netdev.h             |    1 +
 4 files changed, 1237 insertions(+), 0 deletions(-)  create mode 100644 

Old driver

 cpu/arm926ejs/kirkwood/cpu.c |    8 +
 drivers/net/Makefile         |    1 +
 drivers/net/kirkwood_egiga.c | 1670 ++++++++++++++++++++++++++++++++++++++++++
 drivers/net/kirkwood_egiga.h |  828 +++++++++++++++++++++
 include/netdev.h             |    1 +
 5 files changed, 2508 insertions(+), 0 deletions(-)
 create mode 100644 drivers/net/kirkwood_egiga.c
 create mode 100644 drivers/net/kirkwood_egiga.h

Regards..
Prafulla .

Quoted 4 lines

regards,
Ben

#21 lore raw

PATCH 1/1 net: Add Marvell Kirkwood gigabit ethernet driver

Quoted 35 lines · Prafulla Wadaskar
Quoted 35 lines

-----Original Message-----
From: Ben Warren [mailto:biggerbadderben at gmail.com]
Sent: Saturday, May 30, 2009 4:51 AM
To: Jean-Christophe PLAGNIOL-VILLARD
Cc: Prafulla Wadaskar; u-boot at lists.denx.de; Manas Saksena; Ronen Shitrit; Nicolas Pitre; Ashish Karkare; Prabhanjan Sarnaik; Lennert Buijtenhek
Subject: Re: [U-Boot] [PATCH] net: Add Marvell Kirkwood gigabit ethernet driver

Quoted 20 lines · Jean-Christophe PLAGNIOL-VILLARD
Quoted 11 lines · Prafulla Wadaskar

This patch adds a egiga driver for the Marvell Kirkwood SoC's.

Contributors:
Yotam Admon <[email protected]>
Michael Blostein <[email protected]

Ben if it's ok for you I'll apply with rest of the series

Best Regards,
J.

Quoted 9 lines
Quoted 2 lines

I'll look at it this weekend.

Hi Ben,
I have put the huge efforts to tune it specially for code size reduction. Whereas I have lost only network statistics and packet info print debugging features. Now it looks more simpler and cleaner :-)
Hopefully it will stand as per your suggestions.

Much appreciated! Thanks a lot. It looks really good - please just take care of Wolfgang's concerns about error messages and it'll be ready for inclusion.

regards,
Ben

#22 lore raw

PATCH v2 3/5 net: Add Marvell Kirkwood gigabit ethernet driver

This patch adds a egiga driver for the Marvell Kirkwood SoC's.

Contributors:
Yotam Admon <[email protected]>
Michael Blostein <michaelbl at marvell.com

---
Change log:
v2: updated all print messages to provide helpful info

 drivers/net/Makefile         |    1 +
 drivers/net/kirkwood_egiga.c |  664 ++++++++++++++++++++++++++++++++++++++++++
 drivers/net/kirkwood_egiga.h |  561 +++++++++++++++++++++++++++++++++++
 include/netdev.h             |    1 +
 4 files changed, 1227 insertions(+), 0 deletions(-)
 create mode 100644 drivers/net/kirkwood_egiga.c
 create mode 100644 drivers/net/kirkwood_egiga.h
drivers/net/Makefile +1 -0
index a360a50..f0c5654 100644
@@ -40,6 +40,7 @@ COBJS-$(CONFIG_ENC28J60) += enc28j60.o
 COBJS-$(CONFIG_FSLDMAFEC) += fsl_mcdmafec.o mcfmii.o
 COBJS-$(CONFIG_GRETH) += greth.o
 COBJS-$(CONFIG_INCA_IP_SWITCH) += inca-ip_sw.o
+COBJS-$(CONFIG_KIRKWOOD_EGIGA) += kirkwood_egiga.o
 COBJS-$(CONFIG_DRIVER_KS8695ETH) += ks8695eth.o
 COBJS-$(CONFIG_DRIVER_LAN91C96) += lan91c96.o
 COBJS-$(CONFIG_MACB) += macb.o
drivers/net/kirkwood_egiga.c new file +664 -0

664 lines not on this page · raw message

drivers/net/kirkwood_egiga.h new file +561 -0

561 lines not on this page · raw message

include/netdev.h +1 -0
index f37b6ae..3a59f4e 100644
@@ -52,6 +52,7 @@ int fec_initialize (bd_t *bis);
 int greth_initialize(bd_t *bis);
 void gt6426x_eth_initialize(bd_t *bis);
 int inca_switch_initialize(bd_t *bis);
+int kirkwood_egiga_initialize(bd_t *bis);
 int macb_eth_initialize(int id, void *regs, unsigned int phy_addr);
 int mcdmafec_initialize(bd_t *bis);
 int mcffec_initialize(bd_t *bis);
Signature · 1 line
1.5.3.3
#23 lore raw

PATCH 1/1 net: Add Marvell Kirkwood gigabit ethernet driver

In reply to Prafulla Wadaskar

Dear Prafulla Wadaskar,

Quoted 1 line · In message <[email protected]> you wrote:

This patch adds a egiga driver for the Marvell Kirkwood SoC's.

...

drivers/net/kirkwood_egiga.c line 135

Quoted 4 lines
drivers/net/kirkwood_egiga.c new file +4 -0
+	/* check parameters */
+	if ((phy_adr << KWGBE_PHY_SMI_DEV_ADDR_OFFS) &
+		~KWGBE_PHY_SMI_DEV_ADDR_MASK) {
+		printf("Illegal phy address\n");

^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^

drivers/net/kirkwood_egiga.c line 140

Quoted 5 lines
drivers/net/kirkwood_egiga.c new file +5 -0
+		return -EINVAL;
+	}
+	if ((reg_ofs << KWGBE_SMI_REG_ADDR_OFFS) &
+				~KWGBE_SMI_REG_ADDR_MASK) {
+		printf("Illegal register offset\n");

^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^

If you priont an error message, please print a helpful one, i. e. provide the information what failed the test, and why.

drivers/net/kirkwood_egiga.c line 499

Quoted 8 lines
drivers/net/kirkwood_egiga.c new file +8 -0
+static int kwgbe_send(struct eth_device *dev, volatile void *dataptr, int datasize)
+{
+	struct kwgbe_device *dkwgbe = to_dkwgbe(dev);
+	struct kwgbe_registers *regs = dkwgbe->regs;
+	struct kwgbe_txdesc *p_txdesc = dkwgbe->p_txdesc;
+
+	if ((u32)dataptr &0x07) {
+		printf("Err..xmit dataptr not 64bit aligned\n");

Ditto. The user does not even know which driver this is coming from.

Also, please write "dataptr & 0x07".

drivers/net/kirkwood_egiga.c line 522

Quoted 4 lines
drivers/net/kirkwood_egiga.c new file +4 -0
+	while (p_txdesc->cmd_sts & KWGBE_BUFFER_OWNED_BY_DMA) {
+		/* return fail if error is detected */
+		if (p_txdesc->cmd_sts & (KWGBE_UR_ERROR | KWGBE_RL_ERROR)) {
+			printf("Err..in xmit packet\n");

Ditto.

drivers/net/kirkwood_egiga.c line 536

Quoted 8 lines
drivers/net/kirkwood_egiga.c new file +8 -0
+static int kwgbe_recv(struct eth_device *dev)
+{
+	volatile struct kwgbe_device *dkwgbe = to_dkwgbe(dev);
+	volatile struct kwgbe_rxdesc *p_rxdesc_curr= dkwgbe->p_rxdesc_curr;
+
+	/* Sanity check */
+	if (p_rxdesc_curr == NULL) {
+		printf("Err.. null ptr \n");

Please do not print trailing white space.

Also, this error message could be more helpful if you printed where it happened, and which pointer was unexpectedly NULL.

And so on - please check rest of this file, and all other files for _helpful_ error messages.

Best regards,

Wolfgang Denk

Signature · 5 lines
DENX Software Engineering GmbH,     MD: Wolfgang Denk & Detlev Zundel
HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany
Phone: (+49)-8142-66989-10 Fax: (+49)-8142-66989-80 Email: wd at denx.de
Inside every old person is a young person wondering what happened.
                              - Terry Pratchett, _Moving Pictures_
#25 lore raw

PATCH 1/1 spi: Add Marvell Kirkwood SPI driver

...My first pass says this patch doesn't touch on my domain. Is there something I'm missing?

Quoted 15 lines · Jean-Christophe PLAGNIOL-VILLARD
Quoted 3 lines · Prafulla Wadaskar

This patch adds a SPI driver for the Marvell Kirkwood SoC's.

Looks fine

Andy fot you?

Best Regards,
J.
_______________________________________________
U-Boot mailing list
U-Boot at lists.denx.de
http://lists.denx.de/mailman/listinfo/u-boot

#26 lore raw

PATCH 1/1 spi: Add Marvell Kirkwood SPI driver

In reply to Prafulla Wadaskar

Dear Prafulla Wadaskar,

drivers/spi/kirkwood_spi.c line 65

Quoted 5 lines · In message <[email protected]> you wrote:

This patch adds a SPI driver for the Marvell Kirkwood SoC's.

drivers/spi/kirkwood_spi.c new file +3 -0
+	/* program spi clock prescaller using max_hz */
+	writel(KWSPI_ADRLEN_3BYTE | data, &spireg->cfg);
+	debug("data = 0x%08x \n", data);

Please do not print trailing white space.

Best regards,

Wolfgang Denk

Signature · 5 lines
DENX Software Engineering GmbH,     MD: Wolfgang Denk & Detlev Zundel
HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany
Phone: (+49)-8142-66989-10 Fax: (+49)-8142-66989-80 Email: wd at denx.de
Just about every computer on the market today runs Unix,  except  the
Mac (and nobody cares about it).                   - Bill Joy 6/21/85
#27 lore raw

PATCH v2 2/5 spi: Add Marvell Kirkwood SPI driver

This patch adds a SPI driver for the Marvell Kirkwood SoC's.

---
Change log:
v2: White space in debug print removed

 drivers/spi/Makefile                |    1 +
 drivers/spi/kirkwood_spi.c          |  185 +++++++++++++++++++++++++++++++++++
 include/asm-arm/arch-kirkwood/spi.h |   56 +++++++++++
 3 files changed, 242 insertions(+), 0 deletions(-)
 create mode 100644 drivers/spi/kirkwood_spi.c
 create mode 100644 include/asm-arm/arch-kirkwood/spi.h
drivers/spi/Makefile +1 -0
index 1350f3e..7ffa47d 100644
@@ -28,6 +28,7 @@ LIB	:= $(obj)libspi.a
 COBJS-$(CONFIG_ATMEL_DATAFLASH_SPI) += atmel_dataflash_spi.o
 COBJS-$(CONFIG_ATMEL_SPI) += atmel_spi.o
 COBJS-$(CONFIG_BFIN_SPI) += bfin_spi.o
+COBJS-$(CONFIG_KIRKWOOD_SPI) += kirkwood_spi.o
 COBJS-$(CONFIG_MPC8XXX_SPI) += mpc8xxx_spi.o
 COBJS-$(CONFIG_MXC_SPI) += mxc_spi.o
 COBJS-$(CONFIG_SOFT_SPI) += soft_spi.o
drivers/spi/kirkwood_spi.c new file +185 -0

185 lines not on this page · raw message

include/asm-arm/arch-kirkwood/spi.h new file +56 -0

56 lines not on this page · raw message

Signature · 1 line
1.5.3.3
#28 lore raw

PATCH 1/1 spi: Add Marvell Kirkwood SPI driver

In reply to Prafulla Wadaskar
Quoted 10 lines · Prafulla Wadaskar

This patch adds a SPI driver for the Marvell Kirkwood SoC's.

---
 drivers/spi/Makefile                |    1 +
 drivers/spi/kirkwood_spi.c          |  185 +++++++++++++++++++++++++++++++++++
 include/asm-arm/arch-kirkwood/spi.h |   56 +++++++++++
 3 files changed, 242 insertions(+), 0 deletions(-)
 create mode 100644 drivers/spi/kirkwood_spi.c
 create mode 100644 include/asm-arm/arch-kirkwood/spi.h

applied to u-boot-arm

Best Regards,
J.

#29 lore raw

PATCH 1/1 spi: Add Marvell Kirkwood SPI driver

Thanks Jean...

Regards..
Prafulla . .

Quoted 25 lines

-----Original Message-----
From: Jean-Christophe PLAGNIOL-VILLARD [mailto:plagnioj at jcrosoft.com]
Sent: Friday, June 26, 2009 4:30 AM
To: Prafulla Wadaskar
Cc: u-boot at lists.denx.de; Manas Saksena; Ronen Shitrit; Nicolas Pitre; Ashish Karkare; Prabhanjan Sarnaik; Lennert Buijtenhek
Subject: Re: [U-Boot] [PATCH] spi: Add Marvell Kirkwood SPI driver

Quoted 6 lines · Prafulla Wadaskar

This patch adds a SPI driver for the Marvell Kirkwood SoC's.

---
 drivers/spi/Makefile                |    1 +
 drivers/spi/kirkwood_spi.c          |  185 

+++++++++++++++++++++++++++++++++++

Quoted 4 lines
 include/asm-arm/arch-kirkwood/spi.h |   56 +++++++++++
 3 files changed, 242 insertions(+), 0 deletions(-)  create mode 

100644 drivers/spi/kirkwood_spi.c create mode 100644 include/asm-arm/arch-kirkwood/spi.h

applied to u-boot-arm

Best Regards,
J.

#30 lore raw

PATCH 1/1 spi: Add Marvell Kirkwood SPI driver

Quoted 17 lines

-----Original Message-----
From: u-boot-bounces at lists.denx.de
[mailto:u-boot-bounces at lists.denx.de] On Behalf Of Prafulla Wadaskar
Sent: Friday, June 26, 2009 11:28 AM
To: Jean-Christophe PLAGNIOL-VILLARD
Cc: Manas Saksena; Ronen Shitrit; Nicolas Pitre;
u-boot at lists.denx.de; Ashish Karkare; Prabhanjan Sarnaik; Lennert Buijtenhek
Subject: Re: [U-Boot] [PATCH] spi: Add Marvell Kirkwood SPI driver

Thanks Jean...

Regards..
Prafulla . .

Quoted 23 lines
Quoted 2 lines

-----Original Message-----
From: Jean-Christophe PLAGNIOL-VILLARD

[mailto:plagnioj at jcrosoft.com]

Quoted 3 lines

Sent: Friday, June 26, 2009 4:30 AM
To: Prafulla Wadaskar
Cc: u-boot at lists.denx.de; Manas Saksena; Ronen Shitrit;

Nicolas Pitre;

Quoted 16 lines

Ashish Karkare; Prabhanjan Sarnaik; Lennert Buijtenhek
Subject: Re: [U-Boot] [PATCH] spi: Add Marvell Kirkwood SPI driver

Quoted 6 lines · Prafulla Wadaskar

This patch adds a SPI driver for the Marvell Kirkwood SoC's.

---
 drivers/spi/Makefile                |    1 +
 drivers/spi/kirkwood_spi.c          |  185 

+++++++++++++++++++++++++++++++++++

Quoted 4 lines
 include/asm-arm/arch-kirkwood/spi.h |   56 +++++++++++
 3 files changed, 242 insertions(+), 0 deletions(-)  create mode

100644 drivers/spi/kirkwood_spi.c create mode 100644 include/asm-arm/arch-kirkwood/spi.h

applied to u-boot-arm

Hi Jean,

On which branch it is applied?, I could not find it on arm/next...

Regards..
Prafulla . . .

Quoted 9 lines
Quoted 4 lines

Best Regards,
J.

_______________________________________________
U-Boot mailing list
U-Boot at lists.denx.de
http://lists.denx.de/mailman/listinfo/u-boot

#31 lore raw

PATCH 1/1 spi: Add Marvell Kirkwood SPI driver

Quoted 35 lines · Prafulla Wadaskar
Quoted 35 lines

-----Original Message-----
From: u-boot-bounces at lists.denx.de
[mailto:u-boot-bounces at lists.denx.de] On Behalf Of Prafulla Wadaskar
Sent: Friday, June 26, 2009 11:28 AM
To: Jean-Christophe PLAGNIOL-VILLARD
Cc: Manas Saksena; Ronen Shitrit; Nicolas Pitre;
u-boot at lists.denx.de; Ashish Karkare; Prabhanjan Sarnaik; Lennert Buijtenhek
Subject: Re: [U-Boot] [PATCH] spi: Add Marvell Kirkwood SPI driver

Thanks Jean...

Regards..
Prafulla . .

Quoted 2 lines

-----Original Message-----
From: Jean-Christophe PLAGNIOL-VILLARD

[mailto:plagnioj at jcrosoft.com]

Quoted 3 lines

Sent: Friday, June 26, 2009 4:30 AM
To: Prafulla Wadaskar
Cc: u-boot at lists.denx.de; Manas Saksena; Ronen Shitrit;

Nicolas Pitre;

Quoted 11 lines

Ashish Karkare; Prabhanjan Sarnaik; Lennert Buijtenhek
Subject: Re: [U-Boot] [PATCH] spi: Add Marvell Kirkwood SPI driver

Quoted 6 lines · Prafulla Wadaskar

This patch adds a SPI driver for the Marvell Kirkwood SoC's.

---
 drivers/spi/Makefile                |    1 +
 drivers/spi/kirkwood_spi.c          |  185 

+++++++++++++++++++++++++++++++++++

Quoted 8 lines
Quoted 5 lines
Quoted 5 lines
Quoted 4 lines
 include/asm-arm/arch-kirkwood/spi.h |   56 +++++++++++
 3 files changed, 242 insertions(+), 0 deletions(-)  create mode

100644 drivers/spi/kirkwood_spi.c create mode 100644 include/asm-arm/arch-kirkwood/spi.h

applied to u-boot-arm

Hi Jean,

On which branch it is applied?, I could not find it on arm/next...

master

next or testing is still for dev as the master will not build for mtd stuff

Best Regards,
J.

#32 lore raw

PATCH 1/1 spi: Add Marvell Kirkwood SPI driver

Quoted 7 lines

Prafulla Wadaskar

Quoted 6 lines
Quoted 6 lines

Sent: Friday, June 26, 2009 11:28 AM
To: Jean-Christophe PLAGNIOL-VILLARD
Cc: Manas Saksena; Ronen Shitrit; Nicolas Pitre;
u-boot at lists.denx.de; Ashish Karkare; Prabhanjan Sarnaik; Lennert Buijtenhek
Subject: Re: [U-Boot] [PATCH] spi: Add Marvell Kirkwood SPI driver

Quoted 8 lines
Quoted 4 lines
Quoted 1 line
Quoted 1 line

applied to u-boot-arm

Hi Jean,

On which branch it is applied?, I could not find it on arm/next...

master

next or testing is still for dev as the master will not build for mtd stuff

Thanks jean I could see it now :)

Regards..
Prafulla . .

#33 lore raw

PATCH 1/1 arm: Kirkwood: Basic SOCs support

In reply to Prafulla Wadaskar
Quoted 5 lines

+ *
+ * Reference Documentation:
+ * Mbus-L to Mbus Bridge Registers Configuration.
+ * (Sec 25.1 and 25.3 of Datasheet)
+ */

cpu/arm926ejs/kirkwood/cpu.c line 112

Quoted 10 lines
cpu/arm926ejs/kirkwood/cpu.c new file +10 -0
+int kw_config_adr_windows(void)
+{
+	struct kwwin_registers *winregs =
+		(struct kwwin_registers *)KW_CPU_WIN_BASE;
+
+	writel(KWCPU_WIN_CTRL_DATA(0xc0000, KWCPU_TARGET_PCIE,
+				KWCPU_ATTR_PCIE_MEM, KWCPU_WIN_ENABLE),
+		&winregs[0].ctrl);
+
+	writel(0x90000000, &winregs[0].base);

any chance to have some macro for the 0x90000000 & co...

other fine

Best Regards,
J.

#34 lore raw

PATCH 1/1 arm: Kirkwood: Basic SOCs support

Quoted 10 lines

-----Original Message-----
From: Jean-Christophe PLAGNIOL-VILLARD [mailto:plagnioj at jcrosoft.com]
Sent: Saturday, May 30, 2009 3:52 AM
To: Prafulla Wadaskar
Cc: u-boot at lists.denx.de; Manas Saksena; Ronen Shitrit; Nicolas Pitre; Ashish Karkare; Prabhanjan Sarnaik; Lennert Buijtenhek
Subject: Re: [U-Boot] [PATCH] arm: Kirkwood: Basic SOCs support

Quoted 16 lines
Quoted 5 lines

+ *
+ * Reference Documentation:
+ * Mbus-L to Mbus Bridge Registers Configuration.
+ * (Sec 25.1 and 25.3 of Datasheet)
+ */

cpu/arm926ejs/kirkwood/cpu.c line 112

Quoted 10 lines
cpu/arm926ejs/kirkwood/cpu.c new file +10 -0
+int kw_config_adr_windows(void)
+{
+	struct kwwin_registers *winregs =
+		(struct kwwin_registers *)KW_CPU_WIN_BASE;
+
+	writel(KWCPU_WIN_CTRL_DATA(0xc0000, KWCPU_TARGET_PCIE,
+				KWCPU_ATTR_PCIE_MEM, KWCPU_WIN_ENABLE),
+		&winregs[0].ctrl);
+
+	writel(0x90000000, &winregs[0].base);

any chance to have some macro for the 0x90000000 & co...

Hi Jean,
Base address, remap address high, remap address low are the registers need to be programmed with some address value.
Making it macro will not make much sense since the code line itself is readable for objective

Quoted 2 lines

other fine

Please make it everything fine :-)
Waiting eagerly for acceptance

Regards..
Prafulla ..

Quoted 4 lines

Best Regards,
J.

#35 lore raw

PATCH 1/1 arm: Kirkwood: Basic SOCs support

Quoted 26 lines · Prafulla Wadaskar
Quoted 10 lines

-----Original Message-----
From: Jean-Christophe PLAGNIOL-VILLARD [mailto:plagnioj at jcrosoft.com]
Sent: Saturday, May 30, 2009 3:52 AM
To: Prafulla Wadaskar
Cc: u-boot at lists.denx.de; Manas Saksena; Ronen Shitrit; Nicolas Pitre; Ashish Karkare; Prabhanjan Sarnaik; Lennert Buijtenhek
Subject: Re: [U-Boot] [PATCH] arm: Kirkwood: Basic SOCs support

Quoted 16 lines
Quoted 5 lines

+ *
+ * Reference Documentation:
+ * Mbus-L to Mbus Bridge Registers Configuration.
+ * (Sec 25.1 and 25.3 of Datasheet)
+ */

cpu/arm926ejs/kirkwood/cpu.c line 112

Quoted 10 lines
cpu/arm926ejs/kirkwood/cpu.c new file +10 -0
+int kw_config_adr_windows(void)
+{
+	struct kwwin_registers *winregs =
+		(struct kwwin_registers *)KW_CPU_WIN_BASE;
+
+	writel(KWCPU_WIN_CTRL_DATA(0xc0000, KWCPU_TARGET_PCIE,
+				KWCPU_ATTR_PCIE_MEM, KWCPU_WIN_ENABLE),
+		&winregs[0].ctrl);
+
+	writel(0x90000000, &winregs[0].base);

any chance to have some macro for the 0x90000000 & co...

Quoted 4 lines

Hi Jean,
Base address, remap address high, remap address low are the registers need to be programmed with some address value.
Making it macro will not make much sense since the code line itself is readable for objective

so please explain this in the code

Best Regards,
J.

#36 lore raw

PATCH 1/1 arm: Kirkwood: Basic SOCs support

Kirkwood family controllers are highly integrated SOCs based on Feroceon-88FR131/Sheeva-88SV131/arm926ejs cpu core.

SOC versions supported:-
1) 88F6281-A0 define CONFIG_KW88F6281_A0
2) 88F6192-A0 define CONFIG_KW88F6192_A0

Other supported features:-
1) get_random_hex() fucntion
2) PCI Express port initialization
3) NS16550 driver support

Contributors:
Yotam Admon <[email protected]>
Michael Blostein <michaelbl at marvell.com

---
Change log:
v2: explained cpu winregs programming, defined macros too.

 cpu/arm926ejs/kirkwood/Makefile           |   49 +++++
 cpu/arm926ejs/kirkwood/cpu.c              |  315 +++++++++++++++++++++++++++++
 cpu/arm926ejs/kirkwood/dram.c             |   58 ++++++
 cpu/arm926ejs/kirkwood/mpp.c              |   80 ++++++++
 cpu/arm926ejs/kirkwood/timer.c            |  168 +++++++++++++++
 drivers/serial/serial.c                   |    3 +
 include/asm-arm/arch-kirkwood/cpu.h       |  159 +++++++++++++++
 include/asm-arm/arch-kirkwood/kirkwood.h  |   69 +++++++
 include/asm-arm/arch-kirkwood/kw88f6192.h |   37 ++++
 include/asm-arm/arch-kirkwood/kw88f6281.h |   37 ++++
 include/asm-arm/arch-kirkwood/mpp.h       |  303 +++++++++++++++++++++++++++
 11 files changed, 1278 insertions(+), 0 deletions(-)
 create mode 100644 cpu/arm926ejs/kirkwood/Makefile
 create mode 100644 cpu/arm926ejs/kirkwood/cpu.c
 create mode 100644 cpu/arm926ejs/kirkwood/dram.c
 create mode 100644 cpu/arm926ejs/kirkwood/mpp.c
 create mode 100644 cpu/arm926ejs/kirkwood/timer.c
 create mode 100644 include/asm-arm/arch-kirkwood/cpu.h
 create mode 100644 include/asm-arm/arch-kirkwood/kirkwood.h
 create mode 100644 include/asm-arm/arch-kirkwood/kw88f6192.h
 create mode 100644 include/asm-arm/arch-kirkwood/kw88f6281.h
 create mode 100644 include/asm-arm/arch-kirkwood/mpp.h
cpu/arm926ejs/kirkwood/Makefile new file +49 -0
new file mode 100644
index 0000000..d73e210
@@ -0,0 +1,49 @@
+#
+# (C) Copyright 2009
+# Marvell Semiconductor <www.marvell.com>
+# Written-by: Prafulla Wadaskar <[email protected]>
+#
+# See file CREDITS for list of people who contributed to this
+# project.
+#
+# This program is free software; you can redistribute it and/or
+# modify it under the terms of the GNU General Public License as
+# published by the Free Software Foundation; either version 2 of
+# the License, or (at your option) any later version.
+#
+# This program is distributed in the hope that it will be useful,
+# but WITHOUT ANY WARRANTY; without even the implied warranty of
+# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+# GNU General Public License for more details.
+#
+# You should have received a copy of the GNU General Public License
+# along with this program; if not, write to the Free Software
+# Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston,
+# MA 02110-1301 USA
+#
+
+include $(TOPDIR)/config.mk
+
+LIB	= $(obj)lib$(SOC).a
+
+COBJS-y	= dram.o
+COBJS-y	+= cpu.o
+COBJS-y	+= mpp.o
+COBJS-y	+= timer.o
+
+SRCS	:= $(SOBJS:.o=.S) $(COBJS-y:.o=.c)
+OBJS	:= $(addprefix $(obj),$(SOBJS) $(COBJS-y))
+
+all:	$(obj).depend $(LIB)
+
+$(LIB):	$(OBJS)
+	$(AR) $(ARFLAGS) $@ $(OBJS)
+
+#########################################################################
+
+# defines $(obj).depend target
+include $(SRCTREE)/rules.mk
+
+sinclude $(obj).depend
+
+#########################################################################
cpu/arm926ejs/kirkwood/cpu.c new file +315 -0

315 lines not on this page · raw message

cpu/arm926ejs/kirkwood/dram.c new file +58 -0

58 lines not on this page · raw message

cpu/arm926ejs/kirkwood/mpp.c new file +80 -0

80 lines not on this page · raw message

cpu/arm926ejs/kirkwood/timer.c new file +168 -0

168 lines not on this page · raw message

drivers/serial/serial.c +3 -0
index 966df9a..dd5f332 100644
@@ -27,6 +27,9 @@
 #ifdef CONFIG_NS87308
 #include <ns87308.h>
 #endif
+#ifdef CONFIG_KIRKWOOD
+#include <asm/arch/kirkwood.h>
+#endif
 
 #if defined (CONFIG_SERIAL_MULTI)
 #include <serial.h>
include/asm-arm/arch-kirkwood/cpu.h new file +159 -0

159 lines not on this page · raw message

include/asm-arm/arch-kirkwood/kirkwood.h new file +69 -0

69 lines not on this page · raw message

include/asm-arm/arch-kirkwood/kw88f6192.h new file +37 -0
new file mode 100644
index 0000000..bbb7cee
@@ -0,0 +1,37 @@
+/*
+ * (C) Copyright 2009
+ * Marvell Semiconductor <www.marvell.com>
+ * Written-by: Prafulla Wadaskar <[email protected]>
+ *
+ * Header file for Feroceon CPU core 88FR131 Based KW88F6192 SOC.
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston,
+ * MA 02110-1301 USA
+ */
+
+#ifndef _CONFIG_KW88F6192_H
+#define _CONFIG_KW88F6192_H
+
+/* SOC specific definations */
+#define KW88F6192_REGS_PHYS_BASE	0xf1000000
+#define KW_REGS_PHY_BASE		KW88F6192_REGS_PHYS_BASE
+
+/* TCLK Core Clock defination */
+#define CONFIG_SYS_TCLK	  166000000 /* 166MHz */
+
+#endif /* _CONFIG_KW88F6192_H */
include/asm-arm/arch-kirkwood/kw88f6281.h new file +37 -0
new file mode 100644
index 0000000..80723ea
@@ -0,0 +1,37 @@
+/*
+ * (C) Copyright 2009
+ * Marvell Semiconductor <www.marvell.com>
+ * Written-by: Prafulla Wadaskar <[email protected]>
+ *
+ * Header file for Feroceon CPU core 88FR131 Based KW88F6281 SOC.
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston,
+ * MA 02110-1301 USA
+ */
+
+#ifndef _ASM_ARCH_KW88F6281_H
+#define _ASM_ARCH_KW88F6281_H
+
+/* SOC specific definations */
+#define KW88F6281_REGS_PHYS_BASE	0xf1000000
+#define KW_REGS_PHY_BASE		KW88F6281_REGS_PHYS_BASE
+
+/* TCLK Core Clock defination*/
+#define CONFIG_SYS_TCLK	  200000000 /* 200MHz */
+
+#endif /* _ASM_ARCH_KW88F6281_H */
include/asm-arm/arch-kirkwood/mpp.h new file +303 -0

303 lines not on this page · raw message

Signature · 1 line
1.5.3.3
#37 lore raw

PATCH 1/1 arm: Kirkwood: Basic SOCs support

Hi Jean

I have added macros and put some comments in kw_config_adr_windows() for better readability Also I have given references from datasheet too.

This was the only feedback from the last patch.
I Hope this patch is clean to apply
So please kindly review and apply the same

Regards..
Prafulla . .

Quoted 31 lines

-----Original Message-----
From: Prafulla Wadaskar [mailto:prafulla at marvell.com]
Sent: Tuesday, June 02, 2009 3:17 PM
To: u-boot at lists.denx.de
Cc: Nicolas Pitre; Manas Saksena; Lennert Buijtenhek; Prabhanjan Sarnaik; Ronen Shitrit; Ashish Karkare; Prafulla Wadaskar
Subject: [PATCH v1] arm: Kirkwood: Basic SOCs support

Kirkwood family controllers are highly integrated SOCs based on Feroceon-88FR131/Sheeva-88SV131/arm926ejs cpu core.

SOC versions supported:-
1) 88F6281-A0 define CONFIG_KW88F6281_A0
2) 88F6192-A0 define CONFIG_KW88F6192_A0

Other supported features:-
1) get_random_hex() fucntion
2) PCI Express port initialization
3) NS16550 driver support

Contributors:
Yotam Admon <[email protected]>
Michael Blostein <[email protected]

---
Change log:
v2: explained cpu winregs programming, defined macros too.

#38 lore raw

PATCH 1/1 arm: Kirkwood: Basic SOCs support

In reply to Prafulla Wadaskar
Quoted 37 lines · Prafulla Wadaskar

Kirkwood family controllers are highly integrated SOCs based on Feroceon-88FR131/Sheeva-88SV131/arm926ejs cpu core.

SOC versions supported:-
1) 88F6281-A0 define CONFIG_KW88F6281_A0
2) 88F6192-A0 define CONFIG_KW88F6192_A0

Other supported features:-
1) get_random_hex() fucntion
2) PCI Express port initialization
3) NS16550 driver support

Contributors:
Yotam Admon <[email protected]>
Michael Blostein <[email protected]

---
Change log:
v2: explained cpu winregs programming, defined macros too.

 cpu/arm926ejs/kirkwood/Makefile           |   49 +++++
 cpu/arm926ejs/kirkwood/cpu.c              |  315 +++++++++++++++++++++++++++++
 cpu/arm926ejs/kirkwood/dram.c             |   58 ++++++
 cpu/arm926ejs/kirkwood/mpp.c              |   80 ++++++++
 cpu/arm926ejs/kirkwood/timer.c            |  168 +++++++++++++++
 drivers/serial/serial.c                   |    3 +
 include/asm-arm/arch-kirkwood/cpu.h       |  159 +++++++++++++++
 include/asm-arm/arch-kirkwood/kirkwood.h  |   69 +++++++
 include/asm-arm/arch-kirkwood/kw88f6192.h |   37 ++++
 include/asm-arm/arch-kirkwood/kw88f6281.h |   37 ++++
 include/asm-arm/arch-kirkwood/mpp.h       |  303 +++++++++++++++++++++++++++
 11 files changed, 1278 insertions(+), 0 deletions(-)
 create mode 100644 cpu/arm926ejs/kirkwood/Makefile
 create mode 100644 cpu/arm926ejs/kirkwood/cpu.c
Quoted 9 lines
 create mode 100644 cpu/arm926ejs/kirkwood/dram.c
 create mode 100644 cpu/arm926ejs/kirkwood/mpp.c
 create mode 100644 cpu/arm926ejs/kirkwood/timer.c
 create mode 100644 include/asm-arm/arch-kirkwood/cpu.h
 create mode 100644 include/asm-arm/arch-kirkwood/kirkwood.h
 create mode 100644 include/asm-arm/arch-kirkwood/kw88f6192.h
 create mode 100644 include/asm-arm/arch-kirkwood/kw88f6281.h
 create mode 100644 include/asm-arm/arch-kirkwood/mpp.h

applied to arm/next

Best Regards,
J.

#39 lore raw

PATCH 1/1 arm: Kirkwood: Basic SOCs support

Quoted 9 lines

-----Original Message-----
From: Jean-Christophe PLAGNIOL-VILLARD [mailto:plagnioj at jcrosoft.com]
Sent: Sunday, June 07, 2009 5:27 PM
To: Prafulla Wadaskar
Cc: u-boot at lists.denx.de; Manas Saksena; Ronen Shitrit; Nicolas Pitre; Ashish Karkare; Prabhanjan Sarnaik; Lennert Buijtenhek
Subject: Re: [U-Boot] [PATCH v1] arm: Kirkwood: Basic SOCs support

Quoted 6 lines
Quoted 3 lines · Prafulla Wadaskar

Kirkwood family controllers are highly integrated SOCs based on Feroceon-88FR131/Sheeva-88SV131/arm926ejs cpu core.

applied to arm/next

Thanks Jean.

Regards..
Prafulla . .

#40 lore raw

PATCH 1/1 arm: generic cache.h for ARM architectures

In reply to Prafulla Wadaskar

Hi Jean
Thanks for accepting my earlier patch "arch_misc_init support for ARM architectures"
Can you please re-think for this patch too.
This patch is nothing but outcome of our earlier discussion/abstraction to create Generic Cache header for ARM

Also kirkwood Soc support patches are almost done (I think so :-) ) Kirkwood users are very keen to use them right from next release

How I can assist you to get them through?
Shall I resubmit them with the dependency follow-up as suggested by Wolfgang? Reference : http://lists.denx.de/pipermail/u-boot/2009-May/053509.html

Regards..
Prafulla . .

Quoted 67 lines

-----Original Message-----
From: Prafulla Wadaskar [mailto:prafulla at marvell.com]
Sent: Saturday, May 30, 2009 1:14 AM
To: u-boot at lists.denx.de
Cc: Nicolas Pitre; Manas Saksena; Lennert Buijtenhek; Prabhanjan Sarnaik; Ronen Shitrit; Ashish Karkare; Prafulla Wadaskar
Subject: [PATCH] arm: generic cache.h for ARM architectures

This patch is required for Kirkwood SoC support may be used by other ARM architectures

---
 include/asm-arm/cache.h |   41 
+++++++++++++++++++++++++++++++++++++++++
 1 files changed, 41 insertions(+), 0 deletions(-)  create 

mode 100644 include/asm-arm/cache.h

(quoted diff) +0 -0

b/include/asm-arm/cache.h new file mode 100644 index 0000000..205b5da

include/asm-arm/cache.h new file +31 -0
@@ -0,0 +1,41 @@
+/*
+ * (C) Copyright 2009
+ * Marvell Semiconductor <www.marvell.com>
+ * Written-by: Prafulla Wadaskar <[email protected]>
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston,
+ * MA 02110-1301 USA
+ */
+
+#ifndef _ASM_CACHE_H
+#define _ASM_CACHE_H
+
+#include <asm/system.h>
+
+/*
+ * Invalidate L2 Cache using co-proc instruction  */ static 

inline void

include/asm-arm/cache.h new file +8 -1
+invalidate_l2_cache(void) {
+	unsigned int val=0;
+
+	asm volatile("mcr p15, 1, %0, c15, c11, 0 @ invl l2 cache"
+		: : "r" (val) : "cc");
+	isb();
+}
+#endif /* _ASM_CACHE_H */
--

1.5.3.3

#42 lore raw

PATCH 1/1 cpu_misc_init support for ARM architectures

In reply to Prafulla Wadaskar

Dear Prafulla Wadaskar,

Quoted 2 lines · In message <[email protected]> you wrote:

This patch is required for Kirkwood support
may be used by other ARM architectures

I see some (8 ?) patches posted as follow-up - are these supposed to be a series, i. e. do they in any way depend on each other, or need to be applied in a specific order? If so, then please post as numbered patches.

Best regards,

Wolfgang Denk

Signature · 5 lines
DENX Software Engineering GmbH,     MD: Wolfgang Denk & Detlev Zundel
HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany
Phone: (+49)-8142-66989-10 Fax: (+49)-8142-66989-80 Email: wd at denx.de
To the systems programmer,  users  and  applications  serve  only  to
provide a test load.