mpc512x: MPC5121ADS: Add NAND support
PATCH 1/1 mpc512x: MPC5121ADS: Add NAND support
This patch adds NAND support to the MPC5121ADS board. Please note that the image size increased since NAND support didn't fit in the current image size (256k).
Signed-off-by Stefan Roese <[email protected]>
Cc Wolfgang Denk <[email protected]>
--- board/freescale/mpc5121ads/mpc5121ads.c | 27 +++++++++++++++++++++++++++ include/configs/mpc5121ads.h | 22 +++++++++++++++++++++- 2 files changed, 48 insertions(+), 1 deletions(-)
board/freescale/mpc5121ads/mpc5121ads.c +27 -0
@@ -31,6 +31,9 @@#include <i2c.h> #endif +#include <linux/mtd/mtd.h> +#include <linux/mtd/nand.h> +DECLARE_GLOBAL_DATA_PTR ;extern void ide_set_reset (int idereset);
@@ -43,6 +46,7 @@ extern void ide_set_reset(int idereset);CLOCK_SCCR1_DDR_EN | \CLOCK_SCCR1_FEC_EN | \CLOCK_SCCR1_PATA_EN | \ +CLOCK_SCCR1_NFC_EN | \CLOCK_SCCR1_PCI_EN | \ CLOCK_SCCR1_TPR_EN)
@@ -55,6 +59,29 @@ extern void ide_set_reset(int idereset);#define CSAW_STOP (start, size) (((start) + (size) - 1) >> 16)long int fixed_sdram (void ); +void __mpc5121_nfc_select_chip (struct mtd_info *mtd,int chip); + +/* Active chip number set in board_nand_select_device() (mpc5121_nfc.c) */ +extern int mpc5121_nfc_chip; + +/* Control chips select signal on MPC5121ADS board */ +void mpc5121_nfc_select_chip (struct mtd_info *mtd,int chip) +{ +unsigned char *csreg = (u8 *)CONFIG_SYS_CPLD_BASE +0x09 ; +u8 v; + + v =in_8 (csreg); + v |=0x0F ; + +if (chip >=0 ) { +__mpc5121_nfc_select_chip (mtd,0 ); + v &= ~(1 << mpc5121_nfc_chip); + }else { +__mpc5121_nfc_select_chip (mtd,-1 ); + } + +out_8 (csreg, v); +}int board_early_init_f (void ) {
include/configs/mpc5121ads.h +21 -1
@@ -200,6 +200,26 @@#undef CONFIG_SYS_FLASH_CHECKSUM/* +* NAND FLASH +* drivers/mtd/nand/mpc5121_mpc.c (rev 2 silicon only) +*/ +#define CONFIG_CMD_NAND +#define CONFIG_NAND_MPC5121_NFC +#define CONFIG_SYS_NAND_BASE 0x40000000 + +#define CONFIG_SYS_MAX_NAND_DEVICE 2 +#define NAND_MAX_CHIPS CONFIG_SYS_MAX_NAND_DEVICE +#define CONFIG_SYS_NAND_SELECT_DEVICE /* driver supports mutipl. chips */ + +/* +* Configuration parameters for MPC5121 NAND driver +*/ +#define CONFIG_FSL_NFC_WIDTH 1 +#define CONFIG_FSL_NFC_WRITE_SIZE 2048 +#define CONFIG_FSL_NFC_SPARE_SIZE 64 +#define CONFIG_FSL_NFC_CHIPS CONFIG_SYS_MAX_NAND_DEVICE + +/* * CPLD registers area is really only 32 bytes in size, but the smallest possible LP * window is 64KB */
@@ -222,7 +242,7 @@#define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET#define CONFIG_SYS_MONITOR_BASE TEXT_BASE/* Start of monitor */ -#define CONFIG_SYS_MONITOR_LEN (256 * 1024)/* Reserve 256 kB for Mon */ +#define CONFIG_SYS_MONITOR_LEN (512 * 1024)/* Reserve 512 kB for Mon */ #ifdef CONFIG_FSL_DIU_FB #define CONFIG_SYS_MALLOC_LEN (6 * 1024 * 1024)/* Reserved for malloc */ #else
Signature · 1 line
1.6.3.2
PATCH 1/1 mpc512x: MPC5121ADS: Add NAND support
Dear Stefan Roese,
Quoted 10 lines · In message <[email protected]> you wrote:
This patch adds NAND support to the MPC5121ADS board. Please note that the image size increased since NAND support didn't fit in the current image size (256k).
Signed-off-by Stefan Roese <[email protected]>Cc Wolfgang Denk <[email protected]>--- board/freescale/mpc5121ads/mpc5121ads.c | 27 +++++++++++++++++++++++++++ include/configs/mpc5121ads.h | 22 +++++++++++++++++++++- 2 files changed, 48 insertions(+), 1 deletions(-)
Applied to u-boot-mpc5xxx repo (after fixing merge conflicts). Thanks.
Best regards,
Wolfgang Denk
Signature · 7 lines
DENX Software Engineering GmbH, MD: Wolfgang Denk & Detlev Zundel
HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany
Phone: (+49)-8142-66989-10 Fax: (+49)-8142-66989-80 Email: wd at denx.de
Once upon a time, "PC" meant "personal computer". Now it seems to
only mean "Prisoner of Bill". Alas! All my PCs run Unix, and those
include Intel, Sparc, and other processors.
-- Tom "Bring back the non-PC meaning of `PC'" Christiansen