Skip to contentSkip to conversation

mac80211: fix wext bssid/ssid setting

PATCH Superseded Johannes Berg 1 participant 3 messages Jun 15, 2009 mac80211

lore
Share & tools
lore

Johannes Berg

author maintainer
#0 lore raw

PATCH 1/1 mac80211: fix wext bssid/ssid setting

When changing to a new BSSID or SSID, the code in ieee80211_set_disassoc() needs to have the old data still valid to be able to disconnect and clean up properly. Currently, however, the old data is thrown away before ieee80211_set_disassoc() is ever called, so fix that by calling the function _before_ the old data is overwritten.

This is (one of) the issue(s) causing mac80211 to hold cfg80211's BSS structs forever, and them thus being returned in scan results after they're long gone.

---
I'll be so happy when all this goes away to cfg80211...

 net/mac80211/mlme.c |   28 +++++++++++++++++-----------
 1 file changed, 17 insertions(+), 11 deletions(-)
net/mac80211/mlme.c +17 -11
@@ -1102,14 +1102,6 @@ static void ieee80211_set_disassoc(struc
 	struct sta_info *sta;
 	u32 changed = 0, config_changed = 0;
 
-	rcu_read_lock();
-
-	sta = sta_info_get(local, ifmgd->bssid);
-	if (!sta) {
-		rcu_read_unlock();
-		return;
-	}
-
 	if (deauth) {
 		ifmgd->direct_probe_tries = 0;
 		ifmgd->auth_tries = 0;
@@ -1120,7 +1112,14 @@ static void ieee80211_set_disassoc(struc
 	netif_tx_stop_all_queues(sdata->dev);
 	netif_carrier_off(sdata->dev);
 
-	ieee80211_sta_tear_down_BA_sessions(sta);
+	rcu_read_lock();
+	sta = sta_info_get(local, ifmgd->bssid);
+	if (sta)
+		ieee80211_sta_tear_down_BA_sessions(sta);
+	else
+		WARN(1, "Station entry for %pM (%pM) disappeared\n",
+			ifmgd->bssid, ifmgd->prev_bssid);
+	rcu_read_unlock();
 
 	bss = ieee80211_rx_bss_get(local, ifmgd->bssid,
 				   conf->channel->center_freq,
@@ -1156,8 +1155,6 @@ static void ieee80211_set_disassoc(struc
 				ifmgd->ssid, ifmgd->ssid_len);
 	}
 
-	rcu_read_unlock();
-
 	ieee80211_set_wmm_default(sdata);
 
 	ieee80211_recalc_idle(local);
@@ -2479,6 +2476,10 @@ int ieee80211_sta_set_ssid(struct ieee80
 	ifmgd = &sdata->u.mgd;
 
 	if (ifmgd->ssid_len != len || memcmp(ifmgd->ssid, ssid, len) != 0) {
+		if (ifmgd->state == IEEE80211_STA_MLME_ASSOCIATED)
+			ieee80211_set_disassoc(sdata, true, true,
+					       WLAN_REASON_DEAUTH_LEAVING);
+
 		/*
 		 * Do not use reassociation if SSID is changed (different ESS).
 		 */
@@ -2503,6 +2504,11 @@ int ieee80211_sta_set_bssid(struct ieee8
 {
 	struct ieee80211_if_managed *ifmgd = &sdata->u.mgd;
 
+	if (compare_ether_addr(bssid, ifmgd->bssid) != 0 &&
+	    ifmgd->state == IEEE80211_STA_MLME_ASSOCIATED)
+		ieee80211_set_disassoc(sdata, true, true,
+				       WLAN_REASON_DEAUTH_LEAVING);
+
 	if (is_valid_ether_addr(bssid)) {
 		memcpy(ifmgd->bssid, bssid, ETH_ALEN);
 		ifmgd->flags |= IEEE80211_STA_BSSID_SET;
author maintainer
#1 lore raw

PATCH v2 1/1 mac80211: fix wext bssid/ssid setting

When changing to a new BSSID or SSID, the code in ieee80211_set_disassoc() needs to have the old data still valid to be able to disconnect and clean up properly. Currently, however, the old data is thrown away before ieee80211_set_disassoc() is ever called, so fix that by calling the function _before_ the old data is overwritten.

This is (one of) the issue(s) causing mac80211 to hold cfg80211's BSS structs forever, and them thus being returned in scan results after they're long gone.

---
I'll be so happy when all this goes away to cfg80211...

Sorry, the WARN() was for debugging, there are valid code paths where we get there (well, they should be cleaned up and made invalid, but anyway)

 net/mac80211/mlme.c |   25 ++++++++++++++-----------
 1 file changed, 14 insertions(+), 11 deletions(-)
net/mac80211/mlme.c +14 -11
@@ -1102,14 +1102,6 @@ static void ieee80211_set_disassoc(struc
 	struct sta_info *sta;
 	u32 changed = 0, config_changed = 0;
 
-	rcu_read_lock();
-
-	sta = sta_info_get(local, ifmgd->bssid);
-	if (!sta) {
-		rcu_read_unlock();
-		return;
-	}
-
 	if (deauth) {
 		ifmgd->direct_probe_tries = 0;
 		ifmgd->auth_tries = 0;
@@ -1120,7 +1112,11 @@ static void ieee80211_set_disassoc(struc
 	netif_tx_stop_all_queues(sdata->dev);
 	netif_carrier_off(sdata->dev);
 
-	ieee80211_sta_tear_down_BA_sessions(sta);
+	rcu_read_lock();
+	sta = sta_info_get(local, ifmgd->bssid);
+	if (sta)
+		ieee80211_sta_tear_down_BA_sessions(sta);
+	rcu_read_unlock();
 
 	bss = ieee80211_rx_bss_get(local, ifmgd->bssid,
 				   conf->channel->center_freq,
@@ -1156,8 +1152,6 @@ static void ieee80211_set_disassoc(struc
 				ifmgd->ssid, ifmgd->ssid_len);
 	}
 
-	rcu_read_unlock();
-
 	ieee80211_set_wmm_default(sdata);
 
 	ieee80211_recalc_idle(local);
@@ -2479,6 +2473,10 @@ int ieee80211_sta_set_ssid(struct ieee80
 	ifmgd = &sdata->u.mgd;
 
 	if (ifmgd->ssid_len != len || memcmp(ifmgd->ssid, ssid, len) != 0) {
+		if (ifmgd->state == IEEE80211_STA_MLME_ASSOCIATED)
+			ieee80211_set_disassoc(sdata, true, true,
+					       WLAN_REASON_DEAUTH_LEAVING);
+
 		/*
 		 * Do not use reassociation if SSID is changed (different ESS).
 		 */
@@ -2503,6 +2501,11 @@ int ieee80211_sta_set_bssid(struct ieee8
 {
 	struct ieee80211_if_managed *ifmgd = &sdata->u.mgd;
 
+	if (compare_ether_addr(bssid, ifmgd->bssid) != 0 &&
+	    ifmgd->state == IEEE80211_STA_MLME_ASSOCIATED)
+		ieee80211_set_disassoc(sdata, true, true,
+				       WLAN_REASON_DEAUTH_LEAVING);
+
 	if (is_valid_ether_addr(bssid)) {
 		memcpy(ifmgd->bssid, bssid, ETH_ALEN);
 		ifmgd->flags |= IEEE80211_STA_BSSID_SET;
author maintainer
#2 lore raw
Quoted 11 lines · Johannes Berg

When changing to a new BSSID or SSID, the code in ieee80211_set_disassoc() needs to have the old data still valid to be able to disconnect and clean up properly. Currently, however, the old data is thrown away before ieee80211_set_disassoc() is ever called, so fix that by calling the function _before_ the old data is overwritten.

This is (one of) the issue(s) causing mac80211 to hold cfg80211's BSS structs forever, and them thus being returned in scan results after they're long gone.

Also fixes
http://www.intellinuxwireless.org/bugzilla/show_bug.cgi?id=2015

johannes