Kirkwood (Sheevaplug) ping crashes(?) U-Boot
Hi all,
I've tried the first time booting a self compiled u-boot from git.marvell.com U-Boot can be downloaded and started with openocd quite well. Boot messages (version is dirty due to a comment in board file):
U-Boot 2009.06-rc2-02207-g14c575a-dirty (Jun 22 2009 - 13:40:45) Marvell-Sheevaplug
SoC: Kirkwood 88F6281_A0 DRAM: 512 MB NAND: 512 MiB
*** Warning - bad CRC or NAND, using default environment
In: serial Out: serial Err: serial Net: egiga0
88E1116 Initialized on egiga0
Hit any key to stop autoboot: 0
Marvell>>
Environment is broken only with marvell git u-boot. Preflashed u-boot find environment is ok.
Does sheevaplug u-boot from marvell git use other environment settings than preflashed u-boot?
Marvell>> printenv
bootcmd=${x_bootcmd_kernel}; setenv bootargs ${x_bootargs} ${x_bootargs_root}; bootm 0x6400000;
bootdelay=3
baudrate=115200
x_bootargs=console=ttyS0,115200
mtdparts=orion_nand:512k(uboot),3m at 1m(kernel),1m at 4m(psm),13m at 5m(rootfs) rw x_bootcmd_kernel=nand read 0x100000 0x6400000 0x300000 x_bootargs_root=root=/dev/mtdblock3 rw rootfstype=jffs2
stdin=serial
stdout=serial
stderr=serial
ethaddr=00:50:43:e0:b9:d8
ethact=egiga0
ipaddr=192.168.2.75
(ipaddr is set after bootup with setenv ipaddr 192.168.2.75)
If I now try to ping another machine in the same network:
Marvell>> ping 192.168.2.251
Using egiga0 device
This is all what happens - no response from board, CTRL-C doesn't work. Only a hard reset will get the board up again.
Do I have to change something in the default board configuration to succesfullly use networking on the sheevaplug?
u-boot is build with following commands:
make ARCH=arm sheevaplug_config
make
I get no errors during build.
My gcc version is:
arm-none-linux-gnueabi-gcc (GCC) 4.2.0 20070413 (prerelease)
Any help would be appreciated,
Dieter
Dieter,
Quoted 6 lines · Dieter Kiermaier
Hi all,
I've tried the first time booting a self compiled u-boot from git.marvell.com U-Boot can be downloaded and started with openocd quite well. Boot messages (version is dirty due to a comment in board file):
Quoted 7 lines
U-Boot 2009.06-rc2-02207-g14c575a-dirty (Jun 22 2009 - 13:40:45) Marvell-Sheevaplug
SoC: Kirkwood 88F6281_A0 DRAM: 512 MB NAND: 512 MiB*** Warning - bad CRC or NAND, using default environment
most propably you'll need to save the environment.
Quoted 8 lines
In: serial Out: serial Err: serial Net: egiga088E1116 Initialized on egiga0
Hit any key to stop autoboot: 0
Marvell>>
type "save" here and "reset".
Quoted 23 lines
Environment is broken only with marvell git u-boot. Preflashed u-boot find environment is ok.
Does sheevaplug u-boot from marvell git use other environment settings than preflashed u-boot?Marvell>> printenv
bootcmd=${x_bootcmd_kernel}; setenv bootargs ${x_bootargs} ${x_bootargs_root}; bootm0x6400000;
bootdelay=3
baudrate=115200
x_bootargs=console=ttyS0,115200
mtdparts=orion_nand:512k(uboot),3m at 1m(kernel),1m at 4m(psm),13m at 5m(rootfs) rw x_bootcmd_kernel=nand read0x1000000x64000000x300000x_bootargs_root=root=/dev/mtdblock3 rw rootfstype=jffs2
stdin=serial
stdout=serial
stderr=serial
ethaddr=00:50:43:e0:b9:d8
ethact=egiga0
ipaddr=192.168.2.75
Quoted 5 lines
(ipaddr is set after bootup with setenv ipaddr 192.168.2.75)
If I now try to ping another machine in the same network:
Marvell>> ping 192.168.2.251
Using egiga0 device
maybe your MAC is missing ? environment ?
Quoted 14 lines
This is all what happens - no response from board, CTRL-C doesn't work. Only a hard reset will get the board up again.
Do I have to change something in the default board configuration to succesfullly use networking on the sheevaplug?
u-boot is build with following commands:
make ARCH=arm
sheevaplug_config
make
Quoted 9 lines
I get no errors during build.
My gcc version is:
arm-none-linux-gnueabi-gcc (GCC) 4.2.0 20070413 (prerelease)Any help would be appreciated,
Dieter
Regards,
Andr??
Quoted 5 lines
_______________________________________________
U-Boot mailing list
U-Boot at lists.denx.de
http://lists.denx.de/mailman/listinfo/u-boot
MATRIX VISION GmbH, Talstra?e 16, DE-71570 Oppenweiler
Registergericht: Amtsgericht Stuttgart, HRB 271090
Gesch?ftsf?hrer: Gerhard Thullner, Werner Armingeon, Uwe Furtner, Hans-Joachim Reich
Andr??,
Quoted 13 lines
Dieter,
Quoted 10 lines · Dieter Kiermaier
Hi all,
I've tried the first time booting a self compiled u-boot from git.marvell.com U-Boot can be downloaded and started with openocd quite well.
Boot messages (version is dirty due to a comment in board file):U-Boot 2009.06-rc2-02207-g14c575a-dirty (Jun 22 2009 - 13:40:45) Marvell-Sheevaplug
Quoted 6 lines
Quoted 4 lines
SoC: Kirkwood 88F6281_A0 DRAM: 512 MB NAND: 512 MiB*** Warning - bad CRC or NAND, using default environment
most propably you'll need to save the environment.
Also saving environment doesn't help.
The bad CRC message disappered as expected but that's all what happened.
Quoted 32 lines
Quoted 8 lines
In: serial Out: serial Err: serial Net: egiga088E1116 Initialized on egiga0
Hit any key to stop autoboot: 0
Marvell>>type "save" here and "reset".
Quoted 21 lines
Environment is broken only with marvell git u-boot. Preflashed u-boot find environment is ok.
Does sheevaplug u-boot from marvell git use other environment settings than preflashed u-boot?Marvell>> printenv
bootcmd=${x_bootcmd_kernel}; setenv bootargs ${x_bootargs} ${x_bootargs_root}; bootm0x6400000;
bootdelay=3
baudrate=115200
x_bootargs=console=ttyS0,115200
mtdparts=orion_nand:512k(uboot),3m at 1m(kernel),1m at 4m(psm),13m at 5m(rootfs) rw x_bootcmd_kernel=nand read0x1000000x64000000x300000x_bootargs_root=root=/dev/mtdblock3 rw rootfstype=jffs2 stdin=serial
stdout=serial
stderr=serial
ethaddr=00:50:43:e0:b9:d8
ethact=egiga0
ipaddr=192.168.2.75
Quoted 7 lines
Quoted 5 lines
(ipaddr is set after bootup with setenv ipaddr 192.168.2.75)
If I now try to ping another machine in the same network:
Marvell>> ping 192.168.2.251
Using egiga0 devicemaybe your MAC is missing ? environment ?
MAC is available in default (compiled in environment) as shown in env above:
Quoted 1 line
Quoted 1 line
ethaddr=00:50:43:e0:b9:d8
Also writing a new MAC to environment / savenenv / reset made no difference :(
Quoted 17 lines
Quoted 17 lines
This is all what happens - no response from board, CTRL-C doesn't work. Only a hard reset will get the board up again.
Do I have to change something in the default board configuration to succesfullly use networking on the sheevaplug?
u-boot is build with following commands:
make ARCH=arm
sheevaplug_config
makeI get no errors during build.
My gcc version is:
arm-none-linux-gnueabi-gcc (GCC) 4.2.0 20070413 (prerelease)
Quoted 7 lines
Quoted 2 lines
Any help would be appreciated,
DieterRegards,
Andr??
Dieter
Quoted 9 lines
Quoted 4 lines
_______________________________________________
U-Boot mailing list
U-Boot at lists.denx.de
http://lists.denx.de/mailman/listinfo/u-bootMATRIX VISION GmbH, Talstra?e 16, DE-71570 Oppenweiler
Registergericht: Amtsgericht Stuttgart, HRB 271090 Gesch?ftsf?hrer: Gerhard Thullner, Werner Armingeon, Uwe Furtner, Hans-Joachim Reich
Quoted 20 lines · Dieter Kiermaier
Andr??,
Quoted 18 lines
Dieter,
Quoted 14 lines · Dieter Kiermaier
Hi all,
I've tried the first time booting a self compiled u-boot from git.marvell.com U-Boot can be downloaded and started with openocd quite well.
Boot messages (version is dirty due to a comment in board file):U-Boot 2009.06-rc2-02207-g14c575a-dirty (Jun 22 2009 - 13:40:45) Marvell-Sheevaplug
SoC: Kirkwood 88F6281_A0 DRAM: 512 MB NAND: 512 MiB*** Warning - bad CRC or NAND, using default environment
Quoted 38 lines
Quoted 1 line
most propably you'll need to save the environment.
Also saving environment doesn't help.
The bad CRC message disappered as expected but that's all what happened.Quoted 33 lines
Quoted 8 lines
In: serial Out: serial Err: serial Net: egiga088E1116 Initialized on egiga0
Hit any key to stop autoboot: 0
Marvell>>type "save" here and "reset".
Quoted 22 lines
Environment is broken only with marvell git u-boot. Preflashed u-boot find environment is ok.
Does sheevaplug u-boot from marvell git use other environment settings than preflashed u-boot?Marvell>> printenv
bootcmd=${x_bootcmd_kernel}; setenv bootargs ${x_bootargs} ${x_bootargs_root}; bootm0x6400000;
bootdelay=3
baudrate=115200
x_bootargs=console=ttyS0,115200
mtdparts=orion_nand:512k(uboot),3m at 1m(kernel),1m at 4m(psm),13m at 5m(rootfs) rw x_bootcmd_kernel=nand read0x1000000x64000000x300000x_bootargs_root=root=/dev/mtdblock3 rw rootfstype=jffs2 stdin=serial
stdout=serial
stderr=serial
ethaddr=00:50:43:e0:b9:d8
ethact=egiga0
ipaddr=192.168.2.75(ipaddr is set after bootup with setenv ipaddr 192.168.2.75)
Did you try "bootp" or "dhcp" to set up the I/F ?
Quoted 28 lines
Quoted 6 lines
Quoted 4 lines
If I now try to ping another machine in the same network:
Marvell>> ping 192.168.2.251
Using egiga0 devicemaybe your MAC is missing ? environment ?
MAC is available in default (compiled in environment) as shown in env above:
Quoted 1 line
Quoted 1 line
ethaddr=00:50:43:e0:b9:d8
Also writing a new MAC to environment / savenenv / reset made no difference :(
Quoted 17 lines
Quoted 17 lines
This is all what happens - no response from board, CTRL-C doesn't work. Only a hard reset will get the board up again.
Do I have to change something in the default board configuration to succesfullly use networking on the sheevaplug?
u-boot is build with following commands:
make ARCH=arm
sheevaplug_config
makeI get no errors during build.
My gcc version is:
arm-none-linux-gnueabi-gcc (GCC) 4.2.0 20070413 (prerelease)
Quoted 21 lines
Quoted 7 lines
Quoted 2 lines
Any help would be appreciated,
DieterRegards,
Andr??
Dieter
Quoted 9 lines
Quoted 4 lines
_______________________________________________
U-Boot mailing list
U-Boot at lists.denx.de
http://lists.denx.de/mailman/listinfo/u-bootMATRIX VISION GmbH, Talstrae 16, DE-71570 Oppenweiler
Registergericht: Amtsgericht Stuttgart, HRB 271090
Geschftsfhrer: Gerhard Thullner, Werner Armingeon, Uwe Furtner, Hans-Joachim Reich
MATRIX VISION GmbH, Talstra?e 16, DE-71570 Oppenweiler
Registergericht: Amtsgericht Stuttgart, HRB 271090
Gesch?ftsf?hrer: Gerhard Thullner, Werner Armingeon, Uwe Furtner, Hans-Joachim Reich
Am Montag 22 Juni 2009 14:53:44 schrieb Andr?? Schwarz:
Quoted 57 lines · Dieter Kiermaier
Quoted 56 lines
Andr??,
Quoted 13 lines
Dieter,
Quoted 10 lines · Dieter Kiermaier
Hi all,
I've tried the first time booting a self compiled u-boot from git.marvell.com U-Boot can be downloaded and started with openocd quite well.
Boot messages (version is dirty due to a comment in board file):U-Boot 2009.06-rc2-02207-g14c575a-dirty (Jun 22 2009 - 13:40:45) Marvell-Sheevaplug
Quoted 6 lines
Quoted 4 lines
SoC: Kirkwood 88F6281_A0 DRAM: 512 MB NAND: 512 MiB*** Warning - bad CRC or NAND, using default environment
most propably you'll need to save the environment.
Also saving environment doesn't help.
The bad CRC message disappered as expected but that's all what happened.Quoted 31 lines
Quoted 7 lines
In: serial Out: serial Err: serial Net: egiga088E1116 Initialized on egiga0
Hit any key to stop autoboot: 0
Marvell>>type "save" here and "reset".
Quoted 21 lines
Environment is broken only with marvell git u-boot. Preflashed u-boot find environment is ok.
Does sheevaplug u-boot from marvell git use other environment settings than preflashed u-boot?Marvell>> printenv
bootcmd=${x_bootcmd_kernel}; setenv bootargs ${x_bootargs} ${x_bootargs_root}; bootm0x6400000;
bootdelay=3
baudrate=115200
x_bootargs=console=ttyS0,115200 mtdparts=orion_nand:512k(uboot),3m at 1m(kernel),1m at 4m(psm),13m at 5m(rootf
s) rw x_bootcmd_kernel=nand read0x1000000x64000000x300000x_bootargs_root=root=/dev/mtdblock3 rw rootfstype=jffs2 stdin=serial
stdout=serial
stderr=serial
ethaddr=00:50:43:e0:b9:d8
ethact=egiga0
ipaddr=192.168.2.75
Quoted 4 lines
Quoted 1 line
Quoted 1 line
Quoted 1 line
(ipaddr is set after bootup with setenv ipaddr 192.168.2.75)
Did you try "bootp" or "dhcp" to set up the I/F ?
Yes, but everytimes the same:
Marvell>> dhcp
BOOTP broadcast 1
... machine hangs and only a reset helps...
U-Boot 2009.06-rc2-02207-g14c575a-dirty (Jun 22 2009 - 13:40:45) Marvell-Sheevaplug
SoC: Kirkwood 88F6281_A0 DRAM: 512 MB NAND: 512 MiB
*** Warning - bad CRC or NAND, using default environment
In: serial Out: serial Err: serial Net: egiga0
88E1116 Initialized on egiga0
Hit any key to stop autoboot: 0
Marvell>> bootp
BOOTP broadcast 1
...the same here again...
It seems that the network would be activated (1 blink on the activity LED) but nothing more happens.
Quoted 7 lines
Quoted 7 lines
Quoted 5 lines
Quoted 3 lines
If I now try to ping another machine in the same network:
Marvell>> ping 192.168.2.251
Using egiga0 devicemaybe your MAC is missing ? environment ?
MAC is available in default (compiled in environment) as shown in env
above:
Quoted 44 lines
Quoted 21 lines
Quoted 1 line
Quoted 1 line
ethaddr=00:50:43:e0:b9:d8
Also writing a new MAC to environment / savenenv / reset made no difference :(
Quoted 16 lines
Quoted 16 lines
This is all what happens - no response from board, CTRL-C doesn't work. Only a hard reset will get the board up again.
Do I have to change something in the default board configuration to succesfullly use networking on the sheevaplug?
u-boot is build with following commands:
make ARCH=arm
sheevaplug_config
makeI get no errors during build.
My gcc version is:
arm-none-linux-gnueabi-gcc (GCC) 4.2.0 20070413 (prerelease)Quoted 18 lines
Quoted 6 lines
Quoted 2 lines
Any help would be appreciated,
DieterRegards,
Andr??
Dieter
Quoted 9 lines
Quoted 4 lines
_______________________________________________
U-Boot mailing list
U-Boot at lists.denx.de
http://lists.denx.de/mailman/listinfo/u-bootMATRIX VISION GmbH, Talstrae 16, DE-71570 Oppenweiler
Registergericht: Amtsgericht Stuttgart, HRB 271090
Geschftsfhrer: Gerhard Thullner, Werner Armingeon, Uwe Furtner, Hans-Joachim ReichMATRIX VISION GmbH, Talstra?e 16, DE-71570 Oppenweiler
Registergericht: Amtsgericht Stuttgart, HRB 271090 Gesch?ftsf?hrer: Gerhard Thullner, Werner Armingeon, Uwe Furtner, Hans-Joachim Reich
Am Montag 22 Juni 2009 15:08:20 schrieb Dieter Kiermaier:
This seems to be an issue regarding Gigabit / 100MBits uplink with current marvell git u-boot.
If I work with 100MBit/s network show the reported errors. With gigabit connection everything seems to be working fine until now.
Andr??, thanks for your help!
Dieter
Quoted 145 lines
Am Montag 22 Juni 2009 14:53:44 schrieb Andr?? Schwarz:
Quoted 58 lines · Dieter Kiermaier
Quoted 57 lines
Andr??,
Quoted 13 lines
Dieter,
Quoted 10 lines · Dieter Kiermaier
Hi all,
I've tried the first time booting a self compiled u-boot from git.marvell.com U-Boot can be downloaded and started with openocd quite well.
Boot messages (version is dirty due to a comment in board file):U-Boot 2009.06-rc2-02207-g14c575a-dirty (Jun 22 2009 - 13:40:45) Marvell-Sheevaplug
Quoted 6 lines
Quoted 4 lines
SoC: Kirkwood 88F6281_A0 DRAM: 512 MB NAND: 512 MiB*** Warning - bad CRC or NAND, using default environment
most propably you'll need to save the environment.
Also saving environment doesn't help.
The bad CRC message disappered as expected but that's all what happened.Quoted 31 lines
Quoted 7 lines
In: serial Out: serial Err: serial Net: egiga088E1116 Initialized on egiga0
Hit any key to stop autoboot: 0
Marvell>>type "save" here and "reset".
Quoted 21 lines
Environment is broken only with marvell git u-boot. Preflashed u-boot find environment is ok.
Does sheevaplug u-boot from marvell git use other environment settings than preflashed u-boot?Marvell>> printenv
bootcmd=${x_bootcmd_kernel}; setenv bootargs ${x_bootargs} ${x_bootargs_root}; bootm0x6400000;
bootdelay=3
baudrate=115200
x_bootargs=console=ttyS0,115200 mtdparts=orion_nand:512k(uboot),3m at 1m(kernel),1m at 4m(psm),13m at 5m(roo tf s) rw x_bootcmd_kernel=nand read0x1000000x64000000x300000x_bootargs_root=root=/dev/mtdblock3 rw rootfstype=jffs2 stdin=serial
stdout=serial
stderr=serial
ethaddr=00:50:43:e0:b9:d8
ethact=egiga0
ipaddr=192.168.2.75Quoted 3 lines
Quoted 1 line
Quoted 1 line
Quoted 1 line
(ipaddr is set after bootup with setenv ipaddr 192.168.2.75)
Did you try "bootp" or "dhcp" to set up the I/F ?
Yes, but everytimes the same:
Marvell>> dhcp
BOOTP broadcast 1... machine hangs and only a reset helps...
U-Boot 2009.06-rc2-02207-g14c575a-dirty (Jun 22 2009 - 13:40:45) Marvell-Sheevaplug
SoC: Kirkwood 88F6281_A0 DRAM: 512 MB NAND: 512 MiB*** Warning - bad CRC or NAND, using default environment
In: serial Out: serial Err: serial Net: egiga088E1116 Initialized on egiga0
Hit any key to stop autoboot: 0
Marvell>> bootp
BOOTP broadcast 1...the same here again...
It seems that the network would be activated (1 blink on the activity LED) but nothing more happens.
Quoted 7 lines
Quoted 7 lines
Quoted 5 lines
Quoted 3 lines
If I now try to ping another machine in the same network:
Marvell>> ping 192.168.2.251
Using egiga0 devicemaybe your MAC is missing ? environment ?
MAC is available in default (compiled in environment) as shown in env
above:
Quoted 44 lines
Quoted 21 lines
Quoted 1 line
Quoted 1 line
ethaddr=00:50:43:e0:b9:d8
Also writing a new MAC to environment / savenenv / reset made no difference :(
Quoted 16 lines
Quoted 16 lines
This is all what happens - no response from board, CTRL-C doesn't work. Only a hard reset will get the board up again.
Do I have to change something in the default board configuration to succesfullly use networking on the sheevaplug?
u-boot is build with following commands:
make ARCH=arm
sheevaplug_config
makeI get no errors during build.
My gcc version is:
arm-none-linux-gnueabi-gcc (GCC) 4.2.0 20070413 (prerelease)Quoted 18 lines
Quoted 6 lines
Quoted 2 lines
Any help would be appreciated,
DieterRegards,
Andr??
Dieter
Quoted 9 lines
Quoted 4 lines
_______________________________________________
U-Boot mailing list
U-Boot at lists.denx.de
http://lists.denx.de/mailman/listinfo/u-bootMATRIX VISION GmbH, Talstrae 16, DE-71570 Oppenweiler
Registergericht: Amtsgericht Stuttgart, HRB 271090
Geschftsfhrer: Gerhard Thullner, Werner Armingeon, Uwe Furtner, Hans-Joachim ReichMATRIX VISION GmbH, Talstra?e 16, DE-71570 Oppenweiler
Registergericht: Amtsgericht Stuttgart, HRB 271090 Gesch?ftsf?hrer: Gerhard Thullner, Werner Armingeon, Uwe Furtner, Hans-Joachim Reich
Dieter,
Quoted 4 lines · Dieter Kiermaier
Am Montag 22 Juni 2009 15:08:20 schrieb Dieter Kiermaier:
This seems to be an issue regarding Gigabit / 100MBits uplink with current marvell git u-boot.
this gives lots of things worth looking at them :
- are you running on a custom board, i.e. is MDIO known to work properly -> PHY adressing ?
- Does your chips require different clocks for 100M/1000M ?
- What about mis-strapped link advertisement of the PHY ? Maybe 100M-FD disabled ?
Have you tried mii diagnostics ?
Have a look at common/cmd_mii.c -> "mii info" and "mii dump" should be your friends.
Regards,
Andr??
Quoted 155 lines
If I work with 100MBit/s network show the reported errors. With gigabit connection everything seems to be working fine until now.
Andr??, thanks for your help!
DieterQuoted 145 lines
Am Montag 22 Juni 2009 14:53:44 schrieb Andr?? Schwarz:
Quoted 58 lines · Dieter Kiermaier
Quoted 57 lines
Andr??,
Quoted 13 lines
Dieter,
Quoted 10 lines · Dieter Kiermaier
Hi all,
I've tried the first time booting a self compiled u-boot from git.marvell.com U-Boot can be downloaded and started with openocd quite well.
Boot messages (version is dirty due to a comment in board file):U-Boot 2009.06-rc2-02207-g14c575a-dirty (Jun 22 2009 - 13:40:45) Marvell-Sheevaplug
Quoted 6 lines
Quoted 4 lines
SoC: Kirkwood 88F6281_A0 DRAM: 512 MB NAND: 512 MiB*** Warning - bad CRC or NAND, using default environment
most propably you'll need to save the environment.
Also saving environment doesn't help.
The bad CRC message disappered as expected but that's all what happened.Quoted 31 lines
Quoted 7 lines
In: serial Out: serial Err: serial Net: egiga088E1116 Initialized on egiga0
Hit any key to stop autoboot: 0
Marvell>>type "save" here and "reset".
Quoted 21 lines
Environment is broken only with marvell git u-boot. Preflashed u-boot find environment is ok.
Does sheevaplug u-boot from marvell git use other environment settings than preflashed u-boot?Marvell>> printenv
bootcmd=${x_bootcmd_kernel}; setenv bootargs ${x_bootargs} ${x_bootargs_root}; bootm0x6400000;
bootdelay=3
baudrate=115200
x_bootargs=console=ttyS0,115200 mtdparts=orion_nand:512k(uboot),3m at 1m(kernel),1m at 4m(psm),13m at 5m(roo tf s) rw x_bootcmd_kernel=nand read0x1000000x64000000x300000x_bootargs_root=root=/dev/mtdblock3 rw rootfstype=jffs2 stdin=serial
stdout=serial
stderr=serial
ethaddr=00:50:43:e0:b9:d8
ethact=egiga0
ipaddr=192.168.2.75Quoted 3 lines
Quoted 1 line
Quoted 1 line
Quoted 1 line
(ipaddr is set after bootup with setenv ipaddr 192.168.2.75)
Did you try "bootp" or "dhcp" to set up the I/F ?
Yes, but everytimes the same:
Marvell>> dhcp
BOOTP broadcast 1... machine hangs and only a reset helps...
U-Boot 2009.06-rc2-02207-g14c575a-dirty (Jun 22 2009 - 13:40:45) Marvell-Sheevaplug
SoC: Kirkwood 88F6281_A0 DRAM: 512 MB NAND: 512 MiB*** Warning - bad CRC or NAND, using default environment
In: serial Out: serial Err: serial Net: egiga088E1116 Initialized on egiga0
Hit any key to stop autoboot: 0
Marvell>> bootp
BOOTP broadcast 1...the same here again...
It seems that the network would be activated (1 blink on the activity LED) but nothing more happens.
Quoted 7 lines
Quoted 7 lines
Quoted 5 lines
Quoted 3 lines
If I now try to ping another machine in the same network:
Marvell>> ping 192.168.2.251
Using egiga0 devicemaybe your MAC is missing ? environment ?
MAC is available in default (compiled in environment) as shown in env
above:
Quoted 44 lines
Quoted 21 lines
Quoted 1 line
Quoted 1 line
ethaddr=00:50:43:e0:b9:d8
Also writing a new MAC to environment / savenenv / reset made no difference :(
Quoted 16 lines
Quoted 16 lines
This is all what happens - no response from board, CTRL-C doesn't work. Only a hard reset will get the board up again.
Do I have to change something in the default board configuration to succesfullly use networking on the sheevaplug?
u-boot is build with following commands:
make ARCH=arm
sheevaplug_config
makeI get no errors during build.
My gcc version is:
arm-none-linux-gnueabi-gcc (GCC) 4.2.0 20070413 (prerelease)Quoted 18 lines
Quoted 6 lines
Quoted 2 lines
Any help would be appreciated,
DieterRegards,
Andr??
Dieter
Quoted 9 lines
Quoted 4 lines
_______________________________________________
U-Boot mailing list
U-Boot at lists.denx.de
http://lists.denx.de/mailman/listinfo/u-bootMATRIX VISION GmbH, Talstrae 16, DE-71570 Oppenweiler
Registergericht: Amtsgericht Stuttgart, HRB 271090
Geschftsfhrer: Gerhard Thullner, Werner Armingeon, Uwe Furtner, Hans-Joachim ReichMATRIX VISION GmbH, Talstrae 16, DE-71570 Oppenweiler
Registergericht: Amtsgericht Stuttgart, HRB 271090
Geschftsfhrer: Gerhard Thullner, Werner Armingeon, Uwe Furtner, Hans-Joachim Reich
MATRIX VISION GmbH, Talstra?e 16, DE-71570 Oppenweiler
Registergericht: Amtsgericht Stuttgart, HRB 271090
Gesch?ftsf?hrer: Gerhard Thullner, Werner Armingeon, Uwe Furtner, Hans-Joachim Reich
Am Montag 22 Juni 2009 17:34:35 schrieb Andr?? Schwarz:
Andr??,
Quoted 16 lines
Dieter,
Quoted 4 lines · Dieter Kiermaier
Am Montag 22 Juni 2009 15:08:20 schrieb Dieter Kiermaier:
This seems to be an issue regarding Gigabit / 100MBits uplink with current marvell git u-boot.
this gives lots of things worth looking at them :
- are you running on a custom board, i.e. is MDIO known to work properly -> PHY adressing ?
- Does your chips require different clocks for 100M/1000M ?
- What about mis-strapped link advertisement of the PHY ? Maybe 100M-FD disabled ?
Quoted 4 lines
Have you tried mii diagnostics ?
Have a look atcommon/cmd_mii.c-> "mii info" and "mii dump" should be your friends.
I don't think it's a hardware problem.
An older u-boot version provided from marvell works without any problems.
I have contacted Prafulla from marvell. Maybe he's got an idea what's going on wrong there.
Thanks for helping!
Dieter
Quoted 163 lines
Regards,
Andr??Quoted 153 lines
If I work with 100MBit/s network show the reported errors. With gigabit connection everything seems to be working fine until now.
Andr??, thanks for your help!
DieterQuoted 147 lines
Am Montag 22 Juni 2009 14:53:44 schrieb Andr?? Schwarz:
Quoted 59 lines · Dieter Kiermaier
Quoted 58 lines
Andr??,
Quoted 14 lines
Dieter,
Quoted 11 lines · Dieter Kiermaier
Hi all,
I've tried the first time booting a self compiled u-boot from git.marvell.com U-Boot can be downloaded and started with openocd quite well.
Boot messages (version is dirty due to a comment in board file):U-Boot 2009.06-rc2-02207-g14c575a-dirty (Jun 22 2009 - 13:40:45) Marvell-Sheevaplug
Quoted 6 lines
Quoted 4 lines
SoC: Kirkwood 88F6281_A0 DRAM: 512 MB NAND: 512 MiB*** Warning - bad CRC or NAND, using default environment
most propably you'll need to save the environment.
Also saving environment doesn't help.
The bad CRC message disappered as expected but that's all what happened.Quoted 31 lines
Quoted 7 lines
In: serial Out: serial Err: serial Net: egiga088E1116 Initialized on egiga0
Hit any key to stop autoboot: 0
Marvell>>type "save" here and "reset".
Quoted 21 lines
Environment is broken only with marvell git u-boot. Preflashed u-boot find environment is ok.
Does sheevaplug u-boot from marvell git use other environment settings than preflashed u-boot?Marvell>> printenv
bootcmd=${x_bootcmd_kernel}; setenv bootargs ${x_bootargs} ${x_bootargs_root}; bootm0x6400000;
bootdelay=3
baudrate=115200
x_bootargs=console=ttyS0,115200 mtdparts=orion_nand:512k(uboot),3m at 1m(kernel),1m at 4m(psm),13m at 5m (roo tf s) rw x_bootcmd_kernel=nand read0x1000000x64000000x300000x_bootargs_root=root=/dev/mtdblock3 rw rootfstype=jffs2 stdin=serial
stdout=serial
stderr=serial
ethaddr=00:50:43:e0:b9:d8
ethact=egiga0
ipaddr=192.168.2.75Quoted 3 lines
Quoted 1 line
Quoted 1 line
Quoted 1 line
(ipaddr is set after bootup with setenv ipaddr 192.168.2.75)
Did you try "bootp" or "dhcp" to set up the I/F ?
Yes, but everytimes the same:
Marvell>> dhcp
BOOTP broadcast 1... machine hangs and only a reset helps...
U-Boot 2009.06-rc2-02207-g14c575a-dirty (Jun 22 2009 - 13:40:45) Marvell-Sheevaplug
SoC: Kirkwood 88F6281_A0 DRAM: 512 MB NAND: 512 MiB*** Warning - bad CRC or NAND, using default environment
In: serial Out: serial Err: serial Net: egiga088E1116 Initialized on egiga0
Hit any key to stop autoboot: 0
Marvell>> bootp
BOOTP broadcast 1...the same here again...
It seems that the network would be activated (1 blink on the activity LED) but nothing more happens.
Quoted 8 lines
Quoted 8 lines
Quoted 5 lines
Quoted 3 lines
If I now try to ping another machine in the same network:
Marvell>> ping 192.168.2.251
Using egiga0 devicemaybe your MAC is missing ? environment ?
MAC is available in default (compiled in environment) as shown in env
above:
Quoted 44 lines
Quoted 21 lines
Quoted 1 line
Quoted 1 line
ethaddr=00:50:43:e0:b9:d8
Also writing a new MAC to environment / savenenv / reset made no difference :(
Quoted 16 lines
Quoted 16 lines
This is all what happens - no response from board, CTRL-C doesn't work. Only a hard reset will get the board up again.
Do I have to change something in the default board configuration to succesfullly use networking on the sheevaplug?
u-boot is build with following commands:
make ARCH=arm
sheevaplug_config
makeI get no errors during build.
My gcc version is:
arm-none-linux-gnueabi-gcc (GCC) 4.2.0 20070413 (prerelease)Quoted 18 lines
Quoted 6 lines
Quoted 2 lines
Any help would be appreciated,
DieterRegards,
Andr??
Dieter
Quoted 9 lines
Quoted 4 lines
_______________________________________________
U-Boot mailing list
U-Boot at lists.denx.de
http://lists.denx.de/mailman/listinfo/u-bootMATRIX VISION GmbH, Talstrae 16, DE-71570 Oppenweiler
Registergericht: Amtsgericht Stuttgart, HRB 271090
Geschftsfhrer: Gerhard Thullner, Werner Armingeon, Uwe Furtner, Hans-Joachim ReichMATRIX VISION GmbH, Talstrae 16, DE-71570 Oppenweiler
Registergericht: Amtsgericht Stuttgart, HRB 271090
Geschftsfhrer: Gerhard Thullner, Werner Armingeon, Uwe Furtner, Hans-Joachim ReichMATRIX VISION GmbH, Talstra?e 16, DE-71570 Oppenweiler
Registergericht: Amtsgericht Stuttgart, HRB 271090 Gesch?ftsf?hrer: Gerhard Thullner, Werner Armingeon, Uwe Furtner, Hans-Joachim Reich