Skip to contentSkip to conversation

*** SUBJECT HERE ***

PATCH New Senthil Balasubramanian 1 participant 8 messages Jun 24, 2009 Qualcomm Atheros ATH9K wireless driver

lore
Share & tools
lore
#0 lore raw

cover *** SUBJECT HERE ***

John,

I have updated the commit logs as requested by you and also rebased & reorganized my earlier series on the TIP of wireless-testing.

It would be great if the following patches can make it for 2.6.31.

ath9k: Manipulate and report the correct RSSI
ath9k: RX stucks during heavy traffic in HT40 mode.
ath9k: Fix TX hang issue with Atheros chipsets

Senthil

Senthil Balasubramanian (7):
ath9k: Manipulate and report the correct RSSI
ath9k: RX stucks during heavy traffic in HT40 mode.
ath9k: Fix TX hang issue with Atheros chipsets
ath9k: remove unnecessary STATION mode check.
ath9k: stop ani when the STA gets disconnected.
ath9k: race condition in SCANNING state check during ANI calibration
ath9k: Handle different TX and RX streams properly.

 drivers/net/wireless/ath/ath9k/ath9k.h    |   21 +++++++++
 drivers/net/wireless/ath/ath9k/calib.c    |   13 ++++-
 drivers/net/wireless/ath/ath9k/calib.h    |    4 +-
 drivers/net/wireless/ath/ath9k/eeprom.c   |   20 ++++++++-
 drivers/net/wireless/ath/ath9k/initvals.h |   47 +++++++++++----------
 drivers/net/wireless/ath/ath9k/mac.c      |   30 ++++++++++---
 drivers/net/wireless/ath/ath9k/main.c     |   66 ++++++++++++++++------------
 drivers/net/wireless/ath/ath9k/recv.c     |   25 ++++++++++-
 drivers/net/wireless/ath/ath9k/xmit.c     |   57 +++++++++++++++++++------
 9 files changed, 206 insertions(+), 77 deletions(-)
#1 lore raw

PATCH 1/7 ath9k: Manipulate and report the correct RSSI

RSSI reported by the RX descriptor requires little manipulation. Manipulate and report the correct RSSI to the stack. This will fix the improper signal levels reported by iwconfig iw dev wlanX station dump. Also the Link Quality reported seems to be varying (falls to zero also sometimes) when iperf is run from STA to AP.

Also use the default noise floor for now as the one reported during the caliberation seems to be wrong.

The Signal and Link Quality before this patch (taken while TX is in progress from STA to AP)

09:59:13.285428037 Link Quality=29/70  Signal level=-81 dBm
09:59:13.410660084 Link Quality=20/70  Signal level=-90 dBm
09:59:13.586864392 Link Quality=21/70  Signal level=-89 dBm
09:59:13.710296281 Link Quality=21/70  Signal level=-89 dBm
09:59:13.821683064 Link Quality=25/70  Signal level=-85 dBm
09:59:13.933402989 Link Quality=24/70  Signal level=-86 dBm
09:59:14.045839276 Link Quality=26/70  Signal level=-84 dBm
09:59:14.193926673 Link Quality=23/70  Signal level=-87 dBm
09:59:14.306230262 Link Quality=31/70  Signal level=-79 dBm
09:59:14.419459667 Link Quality=26/70  Signal level=-84 dBm
09:59:14.530711167 Link Quality=37/70  Signal level=-73 dBm
09:59:14.642593962 Link Quality=29/70  Signal level=-81 dBm
09:59:14.754361169 Link Quality=21/70  Signal level=-89 dBm
09:59:14.866217355 Link Quality=21/70  Signal level=-89 dBm
09:59:14.976963623 Link Quality=28/70  Signal level=-82 dBm
09:59:15.089149809 Link Quality=26/70  Signal level=-84 dBm
09:59:15.205039887 Link Quality=27/70  Signal level=-83 dBm
09:59:15.316368003 Link Quality=23/70  Signal level=-87 dBm
09:59:15.427684036 Link Quality=36/70  Signal level=-74 dBm
09:59:15.539756380 Link Quality=21/70  Signal level=-89 dBm
09:59:15.650549093 Link Quality=22/70  Signal level=-88 dBm
09:59:15.761171672 Link Quality=32/70  Signal level=-78 dBm
09:59:15.872793750 Link Quality=23/70  Signal level=-87 dBm
09:59:15.984421694 Link Quality=22/70  Signal level=-88 dBm
09:59:16.097315093 Link Quality=21/70  Signal level=-89 dBm

The link quality and signal level after this patch (take while TX is in progress from STA to AP)

17:21:25.627848091 Link Quality=65/70  Signal level=-45 dBm
17:21:25.762805607 Link Quality=65/70  Signal level=-45 dBm
17:21:25.875521888 Link Quality=66/70  Signal level=-44 dBm
17:21:25.987468448 Link Quality=66/70  Signal level=-44 dBm
17:21:26.100628151 Link Quality=66/70  Signal level=-44 dBm
17:21:26.213129671 Link Quality=66/70  Signal level=-44 dBm
17:21:26.324923070 Link Quality=65/70  Signal level=-45 dBm
17:21:26.436831357 Link Quality=65/70  Signal level=-45 dBm
17:21:26.610356973 Link Quality=65/70  Signal level=-45 dBm
17:21:26.723340047 Link Quality=65/70  Signal level=-45 dBm
17:21:26.835715293 Link Quality=64/70  Signal level=-46 dBm
17:21:26.949542748 Link Quality=64/70  Signal level=-46 dBm
17:21:27.062261613 Link Quality=65/70  Signal level=-45 dBm
17:21:27.174511563 Link Quality=64/70  Signal level=-46 dBm
17:21:27.287616232 Link Quality=64/70  Signal level=-46 dBm
17:21:27.400598119 Link Quality=64/70  Signal level=-46 dBm
17:21:27.511381404 Link Quality=64/70  Signal level=-46 dBm
17:21:27.624530421 Link Quality=65/70  Signal level=-45 dBm
17:21:27.737807109 Link Quality=64/70  Signal level=-46 dBm
17:21:27.850861352 Link Quality=65/70  Signal level=-45 dBm
17:21:27.963369436 Link Quality=64/70  Signal level=-46 dBm
17:21:28.076582289 Link Quality=64/70  Signal level=-46 dBm
---
 drivers/net/wireless/ath/ath9k/ath9k.h |   16 ++++++++++++++++
 drivers/net/wireless/ath/ath9k/calib.c |   13 ++++++++++---
 drivers/net/wireless/ath/ath9k/calib.h |    4 +++-
 drivers/net/wireless/ath/ath9k/main.c  |    1 +
 drivers/net/wireless/ath/ath9k/recv.c  |   25 ++++++++++++++++++++++++-
 5 files changed, 54 insertions(+), 5 deletions(-)
drivers/net/wireless/ath/ath9k/ath9k.h +16 -0
index 7425a1f..6fa72b8 100644
@@ -295,12 +295,28 @@ struct ath_tx_control {
 #define ATH_TX_XRETRY       0x02
 #define ATH_TX_BAR          0x04
 
+#define ATH_RSSI_LPF_LEN 		10
+#define RSSI_LPF_THRESHOLD		-20
+#define ATH9K_RSSI_BAD			0x80
+#define ATH_RSSI_EP_MULTIPLIER     (1<<7)
+#define ATH_EP_MUL(x, mul)         ((x) * (mul))
+#define ATH_RSSI_IN(x)             (ATH_EP_MUL((x), ATH_RSSI_EP_MULTIPLIER))
+#define ATH_LPF_RSSI(x, y, len) \
+    ((x != ATH_RSSI_DUMMY_MARKER) ? (((x) * ((len) - 1) + (y)) / (len)) : (y))
+#define ATH_RSSI_LPF(x, y) do {                     			\
+    if ((y) >= RSSI_LPF_THRESHOLD)                         		\
+	x = ATH_LPF_RSSI((x), ATH_RSSI_IN((y)), ATH_RSSI_LPF_LEN);  	\
+} while (0)
+#define ATH_EP_RND(x, mul) 						\
+	((((x)%(mul)) >= ((mul)/2)) ? ((x) + ((mul) - 1)) / (mul) : (x)/(mul))
+
 struct ath_node {
 	struct ath_softc *an_sc;
 	struct ath_atx_tid tid[WME_NUM_TID];
 	struct ath_atx_ac ac[WME_NUM_AC];
 	u16 maxampdu;
 	u8 mpdudensity;
+	int last_rssi;
 };
 
 struct ath_tx {
drivers/net/wireless/ath/ath9k/calib.c +10 -3
index a32d7e7..1f0c5fe 100644
@@ -691,15 +691,22 @@ int16_t ath9k_hw_getnf(struct ath_hw *ah,
 void ath9k_init_nfcal_hist_buffer(struct ath_hw *ah)
 {
 	int i, j;
+	s16 noise_floor;
+
+	if (AR_SREV_9280(ah))
+		noise_floor = AR_PHY_CCA_MAX_AR9280_GOOD_VALUE;
+	else if (AR_SREV_9285(ah))
+		noise_floor = AR_PHY_CCA_MAX_AR9285_GOOD_VALUE;
+	else
+		noise_floor = AR_PHY_CCA_MAX_AR5416_GOOD_VALUE;
 
 	for (i = 0; i < NUM_NF_READINGS; i++) {
 		ah->nfCalHist[i].currIndex = 0;
-		ah->nfCalHist[i].privNF = AR_PHY_CCA_MAX_GOOD_VALUE;
+		ah->nfCalHist[i].privNF = noise_floor;
 		ah->nfCalHist[i].invalidNFcount =
 			AR_PHY_CCA_FILTERWINDOW_LENGTH;
 		for (j = 0; j < ATH9K_NF_CAL_HIST_MAX; j++) {
-			ah->nfCalHist[i].nfCalBuffer[j] =
-				AR_PHY_CCA_MAX_GOOD_VALUE;
+			ah->nfCalHist[i].nfCalBuffer[j] = noise_floor;
 		}
 	}
 }
drivers/net/wireless/ath/ath9k/calib.h +3 -1
index fe5367f..547e697 100644
@@ -25,7 +25,9 @@ extern const struct ath9k_percal_data adc_dc_cal_multi_sample;
 extern const struct ath9k_percal_data adc_dc_cal_single_sample;
 extern const struct ath9k_percal_data adc_init_dc_cal;
 
-#define AR_PHY_CCA_MAX_GOOD_VALUE      		-85
+#define AR_PHY_CCA_MAX_AR5416_GOOD_VALUE	-85
+#define AR_PHY_CCA_MAX_AR9280_GOOD_VALUE	-112
+#define AR_PHY_CCA_MAX_AR9285_GOOD_VALUE	-118
 #define AR_PHY_CCA_MAX_HIGH_VALUE      		-62
 #define AR_PHY_CCA_MIN_BAD_VALUE       		-140
 #define AR_PHY_CCA_FILTERWINDOW_LENGTH_INIT     3
drivers/net/wireless/ath/ath9k/main.c +1 -0
index 66a6c1f..f2bbc28 100644
@@ -463,6 +463,7 @@ static void ath_node_attach(struct ath_softc *sc, struct ieee80211_sta *sta)
 		an->maxampdu = 1 << (IEEE80211_HTCAP_MAXRXAMPDU_FACTOR +
 				     sta->ht_cap.ampdu_factor);
 		an->mpdudensity = parse_mpdudensity(sta->ht_cap.ampdu_density);
+		an->last_rssi = ATH_RSSI_DUMMY_MARKER;
 	}
 }
 
drivers/net/wireless/ath/ath9k/recv.c +24 -1
index 2b2872b..214c4bb 100644
@@ -145,6 +145,10 @@ static int ath_rx_prepare(struct sk_buff *skb, struct ath_desc *ds,
 	u8 ratecode;
 	__le16 fc;
 	struct ieee80211_hw *hw;
+	struct ieee80211_sta *sta;
+	struct ath_node *an;
+	int last_rssi = ATH_RSSI_DUMMY_MARKER;
+
 
 	hdr = (struct ieee80211_hdr *)skb->data;
 	fc = hdr->frame_control;
@@ -229,11 +233,30 @@ static int ath_rx_prepare(struct sk_buff *skb, struct ath_desc *ds,
 		}
 	}
 
+	rcu_read_lock();
+	sta = ieee80211_find_sta(sc->hw, hdr->addr2);
+	if (sta) {
+		an = (struct ath_node *) sta->drv_priv;
+		if (ds->ds_rxstat.rs_rssi != ATH9K_RSSI_BAD &&
+		   !ds->ds_rxstat.rs_moreaggr)
+			ATH_RSSI_LPF(an->last_rssi, ds->ds_rxstat.rs_rssi);
+		last_rssi = an->last_rssi;
+	}
+	rcu_read_unlock();
+
+	if (likely(last_rssi != ATH_RSSI_DUMMY_MARKER))
+		ds->ds_rxstat.rs_rssi = ATH_EP_RND(last_rssi,
+					ATH_RSSI_EP_MULTIPLIER);
+	if (ds->ds_rxstat.rs_rssi < 0)
+		ds->ds_rxstat.rs_rssi = 0;
+	else if (ds->ds_rxstat.rs_rssi > 127)
+		ds->ds_rxstat.rs_rssi = 127;
+
 	rx_status->mactime = ath_extend_tsf(sc, ds->ds_rxstat.rs_tstamp);
 	rx_status->band = hw->conf.channel->band;
 	rx_status->freq = hw->conf.channel->center_freq;
 	rx_status->noise = sc->ani.noise_floor;
-	rx_status->signal = rx_status->noise + ds->ds_rxstat.rs_rssi;
+	rx_status->signal = ATH_DEFAULT_NOISE_FLOOR + ds->ds_rxstat.rs_rssi;
 	rx_status->antenna = ds->ds_rxstat.rs_antenna;
 
 	/* at 45 you will be able to use MCS 15 reliably. A more elaborate
Signature · 1 line
1.6.0.4
#2 lore raw

PATCH 2/7 ath9k: RX stucks during heavy traffic in HT40 mode.

Running iperf along with p2p traffic on both TX and RX side then stop one side, then stop the other side, then start it up again, eventually the STA gets into a mode that it can not pass data at all.

A hardware workaround for invalid RSSI can make FIFO write pointer to jump over read pointer, causing RX data corruption and repeated DMA. Both TX and RX works fine when the workaround is disabled.

To replace the original hardware work around, software looks for frames with post delimiter CRC error and mark the RSSI invalid so that the upperlayer will not use the RSSI associated with this frame. So disable the hardware workaround by updating the appropriate registers.

---
 drivers/net/wireless/ath/ath9k/eeprom.c   |   20 +++++++++++-
 drivers/net/wireless/ath/ath9k/initvals.h |   47 +++++++++++++++-------------
 drivers/net/wireless/ath/ath9k/mac.c      |   30 ++++++++++++++----
 3 files changed, 67 insertions(+), 30 deletions(-)
drivers/net/wireless/ath/ath9k/eeprom.c +19 -1
index a2fda70..5035420 100644
@@ -1208,6 +1208,19 @@ static void ath9k_hw_4k_set_gain(struct ath_hw *ah,
 			      pModal->xatten2Margin[0]);
 		REG_RMW_FIELD(ah, AR_PHY_GAIN_2GHZ + regChainOffset,
 			      AR_PHY_GAIN_2GHZ_XATTEN2_DB, pModal->xatten2Db[0]);
+
+		/* Set the block 1 value to block 0 value */
+		REG_RMW_FIELD(ah, AR_PHY_GAIN_2GHZ + 0x1000,
+			      AR_PHY_GAIN_2GHZ_XATTEN1_MARGIN,
+			      pModal->bswMargin[0]);
+		REG_RMW_FIELD(ah, AR_PHY_GAIN_2GHZ + 0x1000,
+			      AR_PHY_GAIN_2GHZ_XATTEN1_DB, pModal->bswAtten[0]);
+		REG_RMW_FIELD(ah, AR_PHY_GAIN_2GHZ + 0x1000,
+			      AR_PHY_GAIN_2GHZ_XATTEN2_MARGIN,
+			      pModal->xatten2Margin[0]);
+		REG_RMW_FIELD(ah, AR_PHY_GAIN_2GHZ + 0x1000,
+			      AR_PHY_GAIN_2GHZ_XATTEN2_DB,
+			      pModal->xatten2Db[0]);
 	}
 
 	REG_RMW_FIELD(ah, AR_PHY_RXGAIN + regChainOffset,
@@ -1215,6 +1228,11 @@ static void ath9k_hw_4k_set_gain(struct ath_hw *ah,
 	REG_RMW_FIELD(ah, AR_PHY_RXGAIN + regChainOffset,
 		      AR9280_PHY_RXGAIN_TXRX_MARGIN, pModal->rxTxMarginCh[0]);
 
+	REG_RMW_FIELD(ah, AR_PHY_RXGAIN + 0x1000,
+		      AR9280_PHY_RXGAIN_TXRX_ATTEN, txRxAttenLocal);
+	REG_RMW_FIELD(ah, AR_PHY_RXGAIN + 0x1000,
+		      AR9280_PHY_RXGAIN_TXRX_MARGIN, pModal->rxTxMarginCh[0]);
+
 	if (AR_SREV_9285_11(ah))
 		REG_WRITE(ah, AR9285_AN_TOP4, (AR9285_AN_TOP4_DEFAULT | 0x14));
 }
@@ -1239,7 +1257,7 @@ static void ath9k_hw_4k_set_board_values(struct ath_hw *ah,
 	ath9k_hw_4k_set_gain(ah, pModal, eep, txRxAttenLocal, 0);
 
 	/* Initialize Ant Diversity settings from EEPROM */
-	if (pModal->version == 3) {
+	if (pModal->version >= 3) {
 		ant_div_control1 = ((pModal->ob_234 >> 12) & 0xf);
 		ant_div_control2 = ((pModal->db1_234 >> 12) & 0xf);
 		regVal = REG_READ(ah, 0x99ac);
drivers/net/wireless/ath/ath9k/initvals.h +25 -22

104 lines not on this page · raw message

drivers/net/wireless/ath/ath9k/mac.c +23 -7
index 8ae4ec2..6f923e3 100644
@@ -825,13 +825,29 @@ int ath9k_hw_rxprocdesc(struct ath_hw *ah, struct ath_desc *ds,
 	ds->ds_rxstat.rs_datalen = ads.ds_rxstatus1 & AR_DataLen;
 	ds->ds_rxstat.rs_tstamp = ads.AR_RcvTimestamp;
 
-	ds->ds_rxstat.rs_rssi = MS(ads.ds_rxstatus4, AR_RxRSSICombined);
-	ds->ds_rxstat.rs_rssi_ctl0 = MS(ads.ds_rxstatus0, AR_RxRSSIAnt00);
-	ds->ds_rxstat.rs_rssi_ctl1 = MS(ads.ds_rxstatus0, AR_RxRSSIAnt01);
-	ds->ds_rxstat.rs_rssi_ctl2 = MS(ads.ds_rxstatus0, AR_RxRSSIAnt02);
-	ds->ds_rxstat.rs_rssi_ext0 = MS(ads.ds_rxstatus4, AR_RxRSSIAnt10);
-	ds->ds_rxstat.rs_rssi_ext1 = MS(ads.ds_rxstatus4, AR_RxRSSIAnt11);
-	ds->ds_rxstat.rs_rssi_ext2 = MS(ads.ds_rxstatus4, AR_RxRSSIAnt12);
+	if (ads.ds_rxstatus8 & AR_PostDelimCRCErr) {
+		ds->ds_rxstat.rs_rssi = ATH9K_RSSI_BAD;
+		ds->ds_rxstat.rs_rssi_ctl0 = ATH9K_RSSI_BAD;
+		ds->ds_rxstat.rs_rssi_ctl1 = ATH9K_RSSI_BAD;
+		ds->ds_rxstat.rs_rssi_ctl2 = ATH9K_RSSI_BAD;
+		ds->ds_rxstat.rs_rssi_ext0 = ATH9K_RSSI_BAD;
+		ds->ds_rxstat.rs_rssi_ext1 = ATH9K_RSSI_BAD;
+		ds->ds_rxstat.rs_rssi_ext2 = ATH9K_RSSI_BAD;
+	} else {
+		ds->ds_rxstat.rs_rssi = MS(ads.ds_rxstatus4, AR_RxRSSICombined);
+		ds->ds_rxstat.rs_rssi_ctl0 = MS(ads.ds_rxstatus0,
+						AR_RxRSSIAnt00);
+		ds->ds_rxstat.rs_rssi_ctl1 = MS(ads.ds_rxstatus0,
+						AR_RxRSSIAnt01);
+		ds->ds_rxstat.rs_rssi_ctl2 = MS(ads.ds_rxstatus0,
+						AR_RxRSSIAnt02);
+		ds->ds_rxstat.rs_rssi_ext0 = MS(ads.ds_rxstatus4,
+						AR_RxRSSIAnt10);
+		ds->ds_rxstat.rs_rssi_ext1 = MS(ads.ds_rxstatus4,
+						AR_RxRSSIAnt11);
+		ds->ds_rxstat.rs_rssi_ext2 = MS(ads.ds_rxstatus4,
+						AR_RxRSSIAnt12);
+	}
 	if (ads.ds_rxstatus8 & AR_RxKeyIdxValid)
 		ds->ds_rxstat.rs_keyix = MS(ads.ds_rxstatus8, AR_KeyIdx);
 	else
Signature · 1 line
1.6.0.4
#3 lore raw

PATCH 3/7 ath9k: Fix TX hang issue with Atheros chipsets

The hardware doesn't generate interrupts in some cases and so work around this by monitoring the TX status periodically and reset the chip if required.

This behavior of the hardware not generating the TX interrupts can be noticed through ath9k debugfs interrupt statistics when heavy traffic is being sent from STA to AP. One can easily see this behavior when the STA is transmitting at a higher rates. The interrupt statistics in the debugfs interface clearly shows that only RX interrupts alone being generated and TX being stuck.

TX should be monitored through a timer and reset the chip only when frames are queued to the hardware but TX interrupts are not generated for the same even after one second. Also, we shouldn't remove holding descriptor from AC queue if it happens to be the only descriptor and schedule TX aggregation regarless of queue depth as it improves scheduling of AMPDUs from software to hardware queue.

---
 drivers/net/wireless/ath/ath9k/ath9k.h |    4 ++
 drivers/net/wireless/ath/ath9k/main.c  |    3 ++
 drivers/net/wireless/ath/ath9k/xmit.c  |   57 ++++++++++++++++++++++++--------
 3 files changed, 50 insertions(+), 14 deletions(-)
drivers/net/wireless/ath/ath9k/ath9k.h +4 -0
index 6fa72b8..a86e384 100644
@@ -230,6 +230,8 @@ void ath_descdma_cleanup(struct ath_softc *sc, struct ath_descdma *dd,
 #define ATH_DS_TX_BA(_ds)          ((_ds)->ds_us.tx.ts_flags & ATH9K_TX_BA)
 #define ATH_AN_2_TID(_an, _tidno)  (&(_an)->tid[(_tidno)])
 
+#define ATH_TX_COMPLETE_POLL_INT	1000
+
 enum ATH_AGGR_STATUS {
 	ATH_AGGR_DONE,
 	ATH_AGGR_BAW_CLOSED,
@@ -245,6 +247,7 @@ struct ath_txq {
 	u8 axq_aggr_depth;
 	u32 axq_totalqueued;
 	bool stopped;
+	bool axq_tx_inprogress;
 	struct ath_buf *axq_linkbuf;
 
 	/* first desc of the last descriptor that contains CTS */
@@ -609,6 +612,7 @@ struct ath_softc {
 #endif
 	struct ath_bus_ops *bus_ops;
 	struct ath_beacon_config cur_beacon_conf;
+	struct delayed_work tx_complete_work;
 };
 
 struct ath_wiphy {
drivers/net/wireless/ath/ath9k/main.c +3 -0
index f2bbc28..66d2190 100644
@@ -1256,6 +1256,7 @@ void ath_detach(struct ath_softc *sc)
 	ath_deinit_leds(sc);
 	cancel_work_sync(&sc->chan_work);
 	cancel_delayed_work_sync(&sc->wiphy_work);
+	cancel_delayed_work_sync(&sc->tx_complete_work);
 
 	for (i = 0; i < sc->num_sec_wiphy; i++) {
 		struct ath_wiphy *aphy = sc->sec_wiphy[i];
@@ -1974,6 +1975,8 @@ static int ath9k_start(struct ieee80211_hw *hw)
 
 	ieee80211_wake_queues(hw);
 
+	queue_delayed_work(sc->hw->workqueue, &sc->tx_complete_work, 0);
+
 mutex_unlock:
 	mutex_unlock(&sc->mutex);
 
drivers/net/wireless/ath/ath9k/xmit.c +43 -14

100 lines not on this page · raw message

Signature · 1 line
1.6.0.4
#4 lore raw

PATCH 4/7 ath9k: remove unnecessary STATION mode check.

Remove unncessary STATION mode check in ath9k_bss_assoc_info() as it is called only for STATION mode.

---
 drivers/net/wireless/ath/ath9k/main.c |   21 +++++++++------------
 1 files changed, 9 insertions(+), 12 deletions(-)
drivers/net/wireless/ath/ath9k/main.c +8 -11
index 66d2190..a977f80 100644
@@ -921,24 +921,21 @@ static void ath9k_bss_assoc_info(struct ath_softc *sc,
 				 struct ieee80211_vif *vif,
 				 struct ieee80211_bss_conf *bss_conf)
 {
-	struct ath_vif *avp = (void *)vif->drv_priv;
 
 	if (bss_conf->assoc) {
 		DPRINTF(sc, ATH_DBG_CONFIG, "Bss Info ASSOC %d, bssid: %pM\n",
 			bss_conf->aid, sc->curbssid);
 
 		/* New association, store aid */
-		if (avp->av_opmode == NL80211_IFTYPE_STATION) {
-			sc->curaid = bss_conf->aid;
-			ath9k_hw_write_associd(sc);
+		sc->curaid = bss_conf->aid;
+		ath9k_hw_write_associd(sc);
 
-			/*
-			 * Request a re-configuration of Beacon related timers
-			 * on the receipt of the first Beacon frame (i.e.,
-			 * after time sync with the AP).
-			 */
-			sc->sc_flags |= SC_OP_BEACON_SYNC;
-		}
+		/*
+		 * Request a re-configuration of Beacon related timers
+		 * on the receipt of the first Beacon frame (i.e.,
+		 * after time sync with the AP).
+		 */
+		sc->sc_flags |= SC_OP_BEACON_SYNC;
 
 		/* Configure the beacon */
 		ath_beacon_config(sc, vif);
Signature · 1 line
1.6.0.4
#5 lore raw

PATCH 5/7 ath9k: stop ani when the STA gets disconnected.

ANI is not required when the STA is disconnected. So stop it and enable ANI for adhoc and monitor mode.

---
 drivers/net/wireless/ath/ath9k/main.c |    6 +++++-
 1 files changed, 5 insertions(+), 1 deletions(-)
drivers/net/wireless/ath/ath9k/main.c +5 -1
index a977f80..81de792 100644
@@ -950,6 +950,8 @@ static void ath9k_bss_assoc_info(struct ath_softc *sc,
 	} else {
 		DPRINTF(sc, ATH_DBG_CONFIG, "Bss Info DISASSOC\n");
 		sc->curaid = 0;
+		/* Stop ANI */
+		del_timer_sync(&sc->ani.timer);
 	}
 }
 
@@ -2197,7 +2199,9 @@ static int ath9k_add_interface(struct ieee80211_hw *hw,
 
 	ath9k_hw_set_interrupts(sc->sc_ah, sc->imask);
 
-	if (conf->type == NL80211_IFTYPE_AP)
+	if (conf->type == NL80211_IFTYPE_AP    ||
+	    conf->type == NL80211_IFTYPE_ADHOC ||
+	    conf->type == NL80211_IFTYPE_MONITOR)
 		ath_start_ani(sc);
 
 out:
Signature · 1 line
1.6.0.4
#6 lore raw

PATCH 6/7 ath9k: race condition in SCANNING state check during ANI calibration

ANI calibration shouldn't be done when we are not on our home channel. This is already verified. However, it is racy. Fix this by proper spin locks.

---
 drivers/net/wireless/ath/ath9k/ath9k.h |    1 +
 drivers/net/wireless/ath/ath9k/main.c  |   11 +++++++----
 2 files changed, 8 insertions(+), 4 deletions(-)
drivers/net/wireless/ath/ath9k/ath9k.h +1 -0
index a86e384..8de4b86 100644
@@ -563,6 +563,7 @@ struct ath_softc {
 	int irq;
 	spinlock_t sc_resetlock;
 	spinlock_t sc_serial_rw;
+	spinlock_t ani_lock;
 	struct mutex mutex;
 
 	u8 curbssid[ETH_ALEN];
drivers/net/wireless/ath/ath9k/main.c +7 -4
index 81de792..b7d5305 100644
@@ -342,6 +342,7 @@ static void ath_ani_calibrate(unsigned long data)
 	* don't calibrate when we're scanning.
 	* we are most likely not on our home channel.
 	*/
+	spin_lock(&sc->ani_lock);
 	if (sc->sc_flags & SC_OP_SCANNING)
 		goto set_timer;
 
@@ -405,6 +406,7 @@ static void ath_ani_calibrate(unsigned long data)
 	ath9k_ps_restore(sc);
 
 set_timer:
+	spin_unlock(&sc->ani_lock);
 	/*
 	* Set timer interval based on previous results.
 	* The interval must be the shortest necessary to satisfy ANI,
@@ -1312,6 +1314,7 @@ static int ath_init(u16 devid, struct ath_softc *sc)
 	spin_lock_init(&sc->wiphy_lock);
 	spin_lock_init(&sc->sc_resetlock);
 	spin_lock_init(&sc->sc_serial_rw);
+	spin_lock_init(&sc->ani_lock);
 	mutex_init(&sc->mutex);
 	tasklet_init(&sc->intr_tq, ath9k_tasklet, (unsigned long)sc);
 	tasklet_init(&sc->bcon_tasklet, ath_beacon_tasklet,
@@ -2686,9 +2689,9 @@ static void ath9k_sw_scan_start(struct ieee80211_hw *hw)
 	aphy->state = ATH_WIPHY_SCAN;
 	ath9k_wiphy_pause_all_forced(sc, aphy);
 
-	mutex_lock(&sc->mutex);
+	spin_lock_bh(&sc->ani_lock);
 	sc->sc_flags |= SC_OP_SCANNING;
-	mutex_unlock(&sc->mutex);
+	spin_unlock_bh(&sc->ani_lock);
 }
 
 static void ath9k_sw_scan_complete(struct ieee80211_hw *hw)
@@ -2696,11 +2699,11 @@ static void ath9k_sw_scan_complete(struct ieee80211_hw *hw)
 	struct ath_wiphy *aphy = hw->priv;
 	struct ath_softc *sc = aphy->sc;
 
-	mutex_lock(&sc->mutex);
+	spin_lock_bh(&sc->ani_lock);
 	aphy->state = ATH_WIPHY_ACTIVE;
 	sc->sc_flags &= ~SC_OP_SCANNING;
 	sc->sc_flags |= SC_OP_FULL_RESET;
-	mutex_unlock(&sc->mutex);
+	spin_unlock_bh(&sc->ani_lock);
 }
 
 struct ieee80211_ops ath9k_ops = {
Signature · 1 line
1.6.0.4
#7 lore raw

PATCH 7/7 ath9k: Handle different TX and RX streams properly.

This patch fixes an issue when the TX and RX streams are different.

---
 drivers/net/wireless/ath/ath9k/main.c |   26 ++++++++++++++------------
 1 files changed, 14 insertions(+), 12 deletions(-)
drivers/net/wireless/ath/ath9k/main.c +14 -12
index b7d5305..c327dc7 100644
@@ -890,6 +890,7 @@ static void setup_ht_cap(struct ath_softc *sc,
 {
 #define	ATH9K_HT_CAP_MAXRXAMPDU_65536 0x3	/* 2 ^ 16 */
 #define	ATH9K_HT_CAP_MPDUDENSITY_8 0x6		/* 8 usec */
+	u8 tx_streams, rx_streams;
 
 	ht_info->ht_supported = true;
 	ht_info->cap = IEEE80211_HT_CAP_SUP_WIDTH_20_40 |
@@ -902,21 +903,22 @@ static void setup_ht_cap(struct ath_softc *sc,
 
 	/* set up supported mcs set */
 	memset(&ht_info->mcs, 0, sizeof(ht_info->mcs));
+	tx_streams = !(sc->tx_chainmask & (sc->tx_chainmask - 1)) ? 1 : 2;
+	rx_streams = !(sc->rx_chainmask & (sc->rx_chainmask - 1)) ? 1 : 2;
 
-	switch(sc->rx_chainmask) {
-	case 1:
-		ht_info->mcs.rx_mask[0] = 0xff;
-		break;
-	case 3:
-	case 5:
-	case 7:
-	default:
-		ht_info->mcs.rx_mask[0] = 0xff;
-		ht_info->mcs.rx_mask[1] = 0xff;
-		break;
+	if (tx_streams != rx_streams) {
+		DPRINTF(sc, ATH_DBG_CONFIG, "TX streams %d, RX streams: %d\n",
+			tx_streams, rx_streams);
+		ht_info->mcs.tx_params |= IEEE80211_HT_MCS_TX_RX_DIFF;
+		ht_info->mcs.tx_params |= ((tx_streams - 1) <<
+				IEEE80211_HT_MCS_TX_MAX_STREAMS_SHIFT);
 	}
 
-	ht_info->mcs.tx_params = IEEE80211_HT_MCS_TX_DEFINED;
+	ht_info->mcs.rx_mask[0] = 0xff;
+	if (rx_streams >= 2)
+		ht_info->mcs.rx_mask[1] = 0xff;
+
+	ht_info->mcs.tx_params |= IEEE80211_HT_MCS_TX_DEFINED;
 }
 
 static void ath9k_bss_assoc_info(struct ath_softc *sc,
Signature · 1 line
1.6.0.4