85xx: Fix mapping of 0xfffffxxx when CONFIG_MP
PATCH 1/1 85xx: Fix mapping of 0xfffffxxx when CONFIG_MP
Previously, boot page translation was enabled while U-Boot executed. This resulted in the address range 0xfffff000 - 0xffffffff being translated to SDRAM which made the 0xfffffxxx address space unusable for other peripherals.
This change disables boot page translation after the secondary CPU cores have been initialized which allows the 0xfffffxxx address space to be properly accessed.
---
This was tested on the XPedite5370 which has flash mapped in the 0xfffffxxx adddress space. I verified the flash was accessible as expected and Linux properly brought up 2 cores.
I wasn't sure how the MPC8572 handled caching with respect to the boot page translation. I didn't add any cache flushes/invalidates, but they may be necessary if the 0xfffffxxx range is not mapped as uncachable. Anyone at Freescale have any comments on this?
Best,
Peter
cpu/mpc85xx/mp.c | 14 ++++++++++++-- cpu/mpc85xx/release.S | 30 +++++++++++++++++++++++++----- 2 files changed, 37 insertions(+), 7 deletions(-)
cpu/mpc85xx/mp.c +12 -2
@@ -129,7 +129,7 @@ ulong get_spin_addr(void)ulong addr = (ulong )&__spin_table - (ulong )&__secondary_start_page; - addr +=0xfffff000 ; + addr +=determine_mp_bootpg ();return addr; }
@@ -137,7 +137,8 @@ ulong get_spin_addr(void)static void pq3_mp_up (unsigned long bootpg) {u32 up, cpu_up_mask, whoami; -u32 *table = (u32 *)get_spin_addr (); +/* The table is at 0xfffffxxx due to boot page translation below */ +u32 *table = (u32 *)(0xfffff000 |get_spin_addr ());volatile u32 bpcr;volatile ccsr_local_ecm_t *ecm = (void *)(CONFIG_SYS_MPC85xx_ECM_ADDR);volatile ccsr_gur_t *gur = (void *)(CONFIG_SYS_MPC85xx_GUTS_ADDR);
@@ -146,6 +147,8 @@ static void pq3_mp_up(unsigned long bootpg)int timeout =10 ; whoami =in_be32 (&pic->whoami); + +/* Translate 0xfffffxxx 'bootpg' address range to SDRAM */ out_be32 (&ecm->bptr,0x80000000 | (bootpg >>12 ));/* disable time base at the platform */
@@ -194,6 +197,9 @@ static void pq3_mp_up(unsigned long bootpg) devdisr &= ~(MPC85xx_DEVDISR_TB0 | MPC85xx_DEVDISR_TB1);out_be32 (&gur->devdisr, devdisr); + +/* Disable translation of 0xfffffxxx 'bootpg' */ +out_be32 (&ecm->bptr,0x0 ); }void cpu_mp_lmb_reserve (struct lmb *lmb)
@@ -206,9 +212,13 @@ void cpu_mp_lmb_reserve(struct lmb *lmb)void setup_mp (void ) {extern ulong __secondary_start_page; +extern ulong __bootpg_addr;ulong fixup = (ulong)&__secondary_start_page;u32 bootpg =determine_mp_bootpg (); +/* Store the bootpg's SDRAM address for use by secondary CPU cores */ + __bootpg_addr = bootpg; +memcpy ((void *)bootpg, (void *)fixup,4096 );flush_cache (bootpg,4096 );
cpu/mpc85xx/release.S +25 -5
@@ -114,23 +114,38 @@ __secondary_start_page: stw r3,ENTRY_R6_UPPER(r10) stw r3,ENTRY_R6_LOWER(r10) + /* load r13 with the address of the 'bootpg' in SDRAM */ + lis r13,toreset(__bootpg_addr)@h + ori r13,r13,toreset(__bootpg_addr)@l + lwz r13,0(r13) + /* setup mapping for AS = 1, and jump there */ lis r11,(MAS0_TLBSEL(1)|MAS0_ESEL(1))@h mtspr SPRN_MAS0,r11 lis r11,(MAS1_VALID|MAS1_IPROT)@h ori r11,r11,(MAS1_TS|MAS1_TSIZE(BOOKE_PAGESZ_4K))@l mtspr SPRN_MAS1,r11 - lis r11,(0xfffff000|MAS2_I)@h - ori r11,r11,(0xfffff000|MAS2_I)@l + oris r11,r13,(MAS2_I)@h + ori r11,r13,(MAS2_I)@l mtspr SPRN_MAS2,r11 - lis r11,(0xfffff000|MAS3_SX|MAS3_SW|MAS3_SR)@h - ori r11,r11,(0xfffff000|MAS3_SX|MAS3_SW|MAS3_SR)@l + oris r11,r13,(MAS3_SX|MAS3_SW|MAS3_SR)@h + ori r11,r13,(MAS3_SX|MAS3_SW|MAS3_SR)@l mtspr SPRN_MAS3,r11 tlbwe bl 1f 1: mflr r11 - addi r11,r11,28 + /* + * OR in 0xfff to create a mask of the bootpg SDRAM address. We use + * this mask to fixup the cpu spin table and the address that we want + * to jump to, eg change them from 0xfffffxxx to 0x7ffffxxx if the + * bootpg is at 0x7ffff000 in SDRAM. + */ + ori r13,r13,0xfff + and r11, r11, r13 + and r10, r10, r13 + + addi r11,r11,(2f-1b) mfmsr r13 ori r12,r13,MSR_IS|MSR_DS at l
@@ -200,6 +215,11 @@ __secondary_start_page: mtspr SPRN_SRR1,r13 rfi + /* Allocate some space for the SDRAM address of the bootpg */ + .globl __bootpg_addr +__bootpg_addr: + .long 0 + .align L1_CACHE_SHIFT .globl __spin_table __spin_table:
Signature · 1 line
1.6.2.1
PATCH 1/1 85xx: Fix mapping of 0xfffffxxx when CONFIG_MP
Quoted 17 lines · Peter Tyser
Previously, boot page translation was enabled while U-Boot executed. This resulted in the address range
0xfffff000-0xffffffffbeing translated to SDRAM which made the 0xfffffxxx address space unusable for
other peripherals.This change disables boot page translation after the secondary CPU cores
have been initialized which allows the 0xfffffxxx address space to be properly accessed.Signed-off-by Peter Tyser <[email protected]>---
This was tested on the XPedite5370 which has flash mapped in the 0xfffffxxx adddress space. I verified the flash was accessible as expected and Linux properly brought up 2 cores.
Quoted 8 lines
I wasn't sure how the MPC8572 handled caching with respect to the boot page translation. I didn't add any cache flushes/invalidates, but they
may be necessary if the 0xfffffxxx range is not mapped as uncachable. Anyone at Freescale have any comments on this?Best,
Peter
I'm concerned about this because we specifically avoid the 0xfffff000
- 0xffffffff range since if we reset a core we want it to go through boot page translation. Can you explain what you are putting at that address?
- k
PATCH 1/1 85xx: Fix mapping of 0xfffffxxx when CONFIG_MP
Quoted 25 lines · Kumar Gala
Quoted 23 lines · Peter Tyser
Previously, boot page translation was enabled while U-Boot executed. This resulted in the address range
0xfffff000-0xffffffffbeing translated to SDRAM which made the 0xfffffxxx address space unusable for
other peripherals.This change disables boot page translation after the secondary CPU cores
have been initialized which allows the 0xfffffxxx address space to be properly accessed.Signed-off-by Peter Tyser <[email protected]>---
This was tested on the XPedite5370 which has flash mapped in the 0xfffffxxx adddress space. I verified the flash was accessible as expected and Linux properly brought up 2 cores.I wasn't sure how the MPC8572 handled caching with respect to the boot page translation. I didn't add any cache flushes/invalidates, but they
may be necessary if the 0xfffffxxx range is not mapped as uncachable. Anyone at Freescale have any comments on this?
Quoted 7 lines
Quoted 2 lines
Best,
PeterI'm concerned about this because we specifically avoid the
0xfffff000
-0xffffffffrange since if we reset a core we want it to go through boot page translation. Can you explain what you are putting at that address?
Most of our boards (MPC8548, MPC8640, MPC8572-based) have two 128MB flashes - 1 from 0xf0000000-0xf7f00000 and the other from 0xf8000000 - 0xffffffff. We've used this convention for a while, before we started using MPC8572s.
U-Boot is always stored at in the flash at 0xfff80000 on the MPC85xx-based boards we support. Thus I couldn't reprogram U-Boot when CONFIG_MP was defined since the top 4K of flash was really accessing SDRAM because of the boot page translation.
With this patch boot page translation is still used to bring up the secondary cores on power on. This change just makes it so that boot page translation is disabled after the other cores are brought up.
Best,
Peter
PATCH 1/1 85xx: Fix mapping of 0xfffffxxx when CONFIG_MP
Quoted 48 lines · Peter Tyser
Quoted 28 lines · Kumar Gala
Quoted 26 lines · Peter Tyser
Previously, boot page translation was enabled while U-Boot executed. This resulted in the address range
0xfffff000-0xffffffffbeing translated to SDRAM which made the 0xfffffxxx address space unusable for
other peripherals.This change disables boot page translation after the secondary CPU cores
have been initialized which allows the 0xfffffxxx address space to be
properly accessed.Signed-off-by Peter Tyser <[email protected]>---
This was tested on the XPedite5370 which has flash mapped in the 0xfffffxxx adddress space. I verified the flash was accessible as expected and Linux properly brought up 2 cores.I wasn't sure how the MPC8572 handled caching with respect to the boot
page translation. I didn't add any cache flushes/invalidates, but they
may be necessary if the 0xfffffxxx range is not mapped as uncachable.
Anyone at Freescale have any comments on this?Quoted 7 lines
Quoted 2 lines
Best,
PeterI'm concerned about this because we specifically avoid the
0xfffff000
-0xffffffffrange since if we reset a core we want it to go through boot page translation. Can you explain what you are putting at that address?Most of our boards (MPC8548, MPC8640, MPC8572-based) have two 128MB flashes - 1 from 0xf0000000-0xf7f00000 and the other from
0xf8000000-0xffffffff. We've used this convention for a while, before we started using MPC8572s.U-Boot is always stored at in the flash at
0xfff80000on the MPC85xx-based boards we support. Thus I couldn't reprogram U-Boot whenCONFIG_MPwas defined since the top 4K of flash was really accessing SDRAM because of the boot page translation.
Quoted 3 lines
With this patch boot page translation is still used to bring up the secondary cores on power on. This change just makes it so that boot page translation is disabled after the other cores are brought up.
I understand what the patch does. It just removes the capability of soft-resetting a core back into the boot translation code. I understand your problem I'm just not keen on solving it by completely disabling boot translation.
We had a similar memory map and I moved away from it because of the reset vector issues. Additionally, things like >4G of memory also start creeping up.
- k
PATCH 1/1 85xx: Fix mapping of 0xfffffxxx when CONFIG_MP
Quoted 54 lines · Kumar Gala
Quoted 48 lines · Peter Tyser
Quoted 28 lines · Kumar Gala
Quoted 26 lines · Peter Tyser
Previously, boot page translation was enabled while U-Boot executed. This resulted in the address range
0xfffff000-0xffffffffbeing translated to SDRAM which made the 0xfffffxxx address space unusable for
other peripherals.This change disables boot page translation after the secondary CPU cores
have been initialized which allows the 0xfffffxxx address space to be
properly accessed.Signed-off-by Peter Tyser <[email protected]>---
This was tested on the XPedite5370 which has flash mapped in the 0xfffffxxx adddress space. I verified the flash was accessible as expected and Linux properly brought up 2 cores.I wasn't sure how the MPC8572 handled caching with respect to the boot
page translation. I didn't add any cache flushes/invalidates, but they
may be necessary if the 0xfffffxxx range is not mapped as uncachable.
Anyone at Freescale have any comments on this?Quoted 7 lines
Quoted 2 lines
Best,
PeterI'm concerned about this because we specifically avoid the
0xfffff000
-0xffffffffrange since if we reset a core we want it to go through boot page translation. Can you explain what you are putting at that address?Most of our boards (MPC8548, MPC8640, MPC8572-based) have two 128MB flashes - 1 from 0xf0000000-0xf7f00000 and the other from
0xf8000000-0xffffffff. We've used this convention for a while, before we started using MPC8572s.U-Boot is always stored at in the flash at
0xfff80000on the MPC85xx-based boards we support. Thus I couldn't reprogram U-Boot whenCONFIG_MPwas defined since the top 4K of flash was really accessing SDRAM because of the boot page translation.Quoted 3 lines
With this patch boot page translation is still used to bring up the secondary cores on power on. This change just makes it so that boot page translation is disabled after the other cores are brought up.
Quoted 8 lines
I understand what the patch does. It just removes the capability of soft-resetting a core back into the boot translation code. I understand your problem I'm just not keen on solving it by completely disabling boot translation.
We had a similar memory map and I moved away from it because of the reset vector issues. Additionally, things like >4G of memory also start creeping up.
I'm not super familiar with how the MP support in U-Boot is used. Would you be resetting a secondary core for debug purposes? Or is there an example of when you'd reset one in normal operation? I thought normal operation was to use the "cpu release" command, or to let the OS manually take the secondary cores out of their wait loops.
What if I spruced up cpu_reset() to temporarily re-enable boot page translation, then disabled it again? (And maybe re-initialized the cpus MP table so that it could properly ack the primary core similar to in pq3_mp_up().
It seems somewhat dirty to me to constantly keep boot page translation enabled, even when its not needed. Especially since it would require us to change our memory map, environment variable scripts, documentation, etc on all our boards:)
I'd be happy to look into an alternate workaround if you have an idea for a cleaner implementation.
Best,
Peter
PATCH 1/1 85xx: Fix mapping of 0xfffffxxx when CONFIG_MP
Quoted 84 lines · Peter Tyser
Quoted 61 lines · Kumar Gala
Quoted 55 lines · Peter Tyser
Quoted 33 lines · Kumar Gala
Quoted 28 lines · Peter Tyser
Previously, boot page translation was enabled while U-Boot executed.
This resulted in the address range0xfffff000-0xffffffffbeing translated to SDRAM which made the 0xfffffxxx address space unusable
for
other peripherals.This change disables boot page translation after the secondary CPU cores
have been initialized which allows the 0xfffffxxx address space to be
properly accessed.Signed-off-by Peter Tyser <[email protected]>---
This was tested on the XPedite5370 which has flash mapped in the 0xfffffxxx adddress space. I verified the flash was accessible as expected and Linux properly brought up 2 cores.I wasn't sure how the MPC8572 handled caching with respect to the boot
page translation. I didn't add any cache flushes/invalidates, but they
may be necessary if the 0xfffffxxx range is not mapped as uncachable.
Anyone at Freescale have any comments on this?Quoted 2 lines
Best,
PeterQuoted 7 lines
I'm concerned about this because we specifically avoid the
0xfffff000
-0xffffffffrange since if we reset a core we want it to go through
boot page translation. Can you explain what you are putting at that
address?Most of our boards (MPC8548, MPC8640, MPC8572-based) have two 128MB flashes - 1 from 0xf0000000-0xf7f00000 and the other from
0xf8000000-0xffffffff. We've used this convention for a while, before we started
using MPC8572s.U-Boot is always stored at in the flash at
0xfff80000on the MPC85xx-based boards we support. Thus I couldn't reprogram U-Boot whenCONFIG_MPwas defined since the top 4K of flash was really accessing SDRAM because of the boot page translation.Quoted 3 lines
With this patch boot page translation is still used to bring up the secondary cores on power on. This change just makes it so that boot page translation is disabled after the other cores are brought up.
Quoted 8 lines
I understand what the patch does. It just removes the capability of soft-resetting a core back into the boot translation code. I understand your problem I'm just not keen on solving it by completely disabling boot translation.
We had a similar memory map and I moved away from it because of the reset vector issues. Additionally, things like >4G of memory also start creeping up.
I'm not super familiar with how the MP support in U-Boot is used. Would
you be resetting a secondary core for debug purposes? Or is there an example of when you'd reset one in normal operation? I thought normal operation was to use the "cpu release" command, or to let the OS manually take the secondary cores out of their wait loops.What if I spruced up
cpu_reset()to temporarily re-enable boot page translation, then disabled it again? (And maybe re-initialized the cpus
MP table so that it could properly ack the primary core similar to inpq3_mp_up().
Quoted 8 lines
It seems somewhat dirty to me to constantly keep boot page translation enabled, even when its not needed. Especially since it would require us
to change our memory map, environment variable scripts, documentation, etc on all our boards:)I'd be happy to look into an alternate workaround if you have an idea for a cleaner implementation.
The idea is after u-boot if you soft-reset a core that it would go back into the spin table code. U-boot is long gone at this point.
- k
PATCH 1/1 85xx: Fix mapping of 0xfffffxxx when CONFIG_MP
Quoted 92 lines · Kumar Gala
Quoted 90 lines · Peter Tyser
Quoted 61 lines · Kumar Gala
Quoted 55 lines · Peter Tyser
Quoted 33 lines · Kumar Gala
Quoted 28 lines · Peter Tyser
Previously, boot page translation was enabled while U-Boot executed.
This resulted in the address range0xfffff000-0xffffffffbeing translated to SDRAM which made the 0xfffffxxx address space unusable
for
other peripherals.This change disables boot page translation after the secondary CPU cores
have been initialized which allows the 0xfffffxxx address space to be
properly accessed.Signed-off-by Peter Tyser <[email protected]>---
This was tested on the XPedite5370 which has flash mapped in the 0xfffffxxx adddress space. I verified the flash was accessible as expected and Linux properly brought up 2 cores.I wasn't sure how the MPC8572 handled caching with respect to the boot
page translation. I didn't add any cache flushes/invalidates, but they
may be necessary if the 0xfffffxxx range is not mapped as uncachable.
Anyone at Freescale have any comments on this?Quoted 2 lines
Best,
PeterQuoted 7 lines
I'm concerned about this because we specifically avoid the
0xfffff000
-0xffffffffrange since if we reset a core we want it to go through
boot page translation. Can you explain what you are putting at that
address?Most of our boards (MPC8548, MPC8640, MPC8572-based) have two 128MB flashes - 1 from 0xf0000000-0xf7f00000 and the other from
0xf8000000-0xffffffff. We've used this convention for a while, before we started
using MPC8572s.U-Boot is always stored at in the flash at
0xfff80000on the MPC85xx-based boards we support. Thus I couldn't reprogram U-Boot whenCONFIG_MPwas defined since the top 4K of flash was really accessing SDRAM because of the boot page translation.Quoted 3 lines
With this patch boot page translation is still used to bring up the secondary cores on power on. This change just makes it so that boot page translation is disabled after the other cores are brought up.
Quoted 8 lines
I understand what the patch does. It just removes the capability of soft-resetting a core back into the boot translation code. I understand your problem I'm just not keen on solving it by completely disabling boot translation.
We had a similar memory map and I moved away from it because of the reset vector issues. Additionally, things like >4G of memory also start creeping up.
I'm not super familiar with how the MP support in U-Boot is used. Would
you be resetting a secondary core for debug purposes? Or is there an example of when you'd reset one in normal operation? I thought normal operation was to use the "cpu release" command, or to let the OS manually take the secondary cores out of their wait loops.What if I spruced up
cpu_reset()to temporarily re-enable boot page translation, then disabled it again? (And maybe re-initialized the cpus
MP table so that it could properly ack the primary core similar to inpq3_mp_up().It seems somewhat dirty to me to constantly keep boot page translation enabled, even when its not needed. Especially since it would require us
to change our memory map, environment variable scripts, documentation, etc on all our boards:)
Quoted 5 lines
Quoted 2 lines
I'd be happy to look into an alternate workaround if you have an idea for a cleaner implementation.
The idea is after u-boot if you soft-reset a core that it would go back into the spin table code. U-boot is long gone at this point.
Are there common scenarios where a core would be reset after its already booted an OS? If an OS did need to soft-reset a secondary core, shouldn't the OS be responsible for ensuring boot page translation is enabled, its translating to the proper location, etc? For example, I imagine non-Linux OSes bring up secondary cores in different manners and some wouldn't re-utilize U-Boot's boot page code located in SDRAM at all, thus they wouldn't want the boot page translation always enabled.
It just seems less than ideal to have a chunk of memory space that somewhat magically accesses a completely different, unintuitive address space. Someone else ran into the same issue already:
http://www.mail-archive.com/u-boot at lists.denx.de/msg08361.html
I realize there's a tradeoff between keeping the translation enabled vs disabled, I'm just not familiar with how OSes utilize the secondary cores to know what the downsides of disabling translation are...
Best,
Peter
PATCH 1/1 85xx: Fix mapping of 0xfffffxxx when CONFIG_MP
Hi Kumar,
Quoted 42 lines
Quoted 28 lines
Quoted 28 lines
Quoted 8 lines
I understand what the patch does. It just removes the capability of soft-resetting a core back into the boot translation code. I understand your problem I'm just not keen on solving it by completely disabling boot translation.
We had a similar memory map and I moved away from it because of the reset vector issues. Additionally, things like >4G of memory also start creeping up.
I'm not super familiar with how the MP support in U-Boot is used. Would
you be resetting a secondary core for debug purposes? Or is there an example of when you'd reset one in normal operation? I thought normal operation was to use the "cpu release" command, or to let the OS manually take the secondary cores out of their wait loops.What if I spruced up
cpu_reset()to temporarily re-enable boot page translation, then disabled it again? (And maybe re-initialized the cpus
MP table so that it could properly ack the primary core similar to inpq3_mp_up().It seems somewhat dirty to me to constantly keep boot page translation enabled, even when its not needed. Especially since it would require us
to change our memory map, environment variable scripts, documentation, etc on all our boards:)Quoted 5 lines
Quoted 2 lines
I'd be happy to look into an alternate workaround if you have an idea for a cleaner implementation.
The idea is after u-boot if you soft-reset a core that it would go back into the spin table code. U-boot is long gone at this point.
Are there common scenarios where a core would be reset after its already booted an OS? If an OS did need to soft-reset a secondary core, shouldn't the OS be responsible for ensuring boot page translation is enabled, its translating to the proper location, etc? For example, I imagine non-Linux OSes bring up secondary cores in different manners and some wouldn't re-utilize U-Boot's boot page code located in SDRAM at all, thus they wouldn't want the boot page translation always enabled.
Quoted 8 lines
It just seems less than ideal to have a chunk of memory space that somewhat magically accesses a completely different, unintuitive address space. Someone else ran into the same issue already:
http://www.mail-archive.com/u-boot at lists.denx.de/msg08361.htmlI realize there's a tradeoff between keeping the translation enabled vs disabled, I'm just not familiar with how OSes utilize the secondary cores to know what the downsides of disabling translation are...
Any feedback on my last email above, or is disabling boot page translation just a no-go?
Or is there an more ideal alternative? I really don't want to change up the memory map on all our Freescale boards, documentation, dts files, etc because of an optional 4KB chunk of memory space:) I'm more than willing to implement a different workaround if it means we can keep our current memory map...
Thanks,
Peter
PATCH 1/1 85xx: Fix mapping of 0xfffffxxx when CONFIG_MP
Quoted 62 lines · Peter Tyser
Hi Kumar,
Quoted 60 lines
Quoted 36 lines
Quoted 36 lines
Quoted 11 lines
I understand what the patch does. It just removes the capability of
soft-resetting a core back into the boot translation code. I understand your problem I'm just not keen on solving it by completely
disabling boot translation.We had a similar memory map and I moved away from it because of the
reset vector issues. Additionally, things like >4G of memory also start creeping up.I'm not super familiar with how the MP support in U-Boot is used. Would
you be resetting a secondary core for debug purposes? Or is there an
example of when you'd reset one in normal operation? I thought normal
operation was to use the "cpu release" command, or to let the OS manually take the secondary cores out of their wait loops.What if I spruced up
cpu_reset()to temporarily re-enable boot page translation, then disabled it again? (And maybe re-initialized the cpus
MP table so that it could properly ack the primary core similar to inpq3_mp_up().It seems somewhat dirty to me to constantly keep boot page translation
enabled, even when its not needed. Especially since it would require us
to change our memory map, environment variable scripts, documentation,
etc on all our boards:)Quoted 6 lines
Quoted 3 lines
I'd be happy to look into an alternate workaround if you have an idea
for a cleaner implementation.The idea is after u-boot if you soft-reset a core that it would go back into the spin table code. U-boot is long gone at this point.
Are there common scenarios where a core would be reset after its already
booted an OS? If an OS did need to soft-reset a secondary core, shouldn't the OS be responsible for ensuring boot page translation is enabled, its translating to the proper location, etc? For example, I imagine non-Linux OSes bring up secondary cores in different manners and
some wouldn't re-utilize U-Boot's boot page code located in SDRAM at all, thus they wouldn't want the boot page translation always enabled.It just seems less than ideal to have a chunk of memory space that somewhat magically accesses a completely different, unintuitive address
space. Someone else ran into the same issue already:
http://www.mail-archive.com/u-boot at lists.denx.de/msg08361.html
Quoted 7 lines
Quoted 4 lines
I realize there's a tradeoff between keeping the translation enabled vs
disabled, I'm just not familiar with how OSes utilize the secondary cores to know what the downsides of disabling translation are...Any feedback on my last email above, or is disabling boot page translation just a no-go?
It is at this point.
Quoted 7 lines
Or is there an more ideal alternative? I really don't want to change up
the memory map on all our Freescale boards, documentation, dts files, etc because of an optional 4KB chunk of memory space:) I'm more than willing to implement a different workaround if it means we can keep our
current memory map...
I'd be fine if we want to add a CONFIG_ option to do the disable so board ports that need/want it can do it.
- k
PATCH 1/1 85xx: Fix mapping of 0xfffffxxx when CONFIG_MP
Quoted 14 lines
Quoted 3 lines
Any feedback on my last email above, or is disabling boot page translation just a no-go?
It is at this point.
Quoted 7 lines
Or is there an more ideal alternative? I really don't want to change up
the memory map on all our Freescale boards, documentation, dts files, etc because of an optional 4KB chunk of memory space:) I'm more than willing to implement a different workaround if it means we can keep our
current memory map...
Quoted 2 lines
I'd be fine if we want to add a
CONFIG_option to do the disable so board ports that need/want it can do it.
OK, that sounds good. I'll implement and test. Thanks,
Peter