Panic on IBMMCA SCSI driver with 2.6.30
No, this isn't a joke. I actually still have an IBM 9595, and I've been running 2.4 on it all this time. A friend of mine tried to upgrade one to 2.6 and couldn't get it to boot. I managed to get a bit of serial console output of the error it is throwing. I don't speak SCSI very well, so I'm hoping that you guys might have some insight.
I added all the debug output that I could find. I actually have a tiny compile fix or two for the debug code that I'll send along in a bit. I'm sure the other 3 MCA users will appreciate it.
Alan and James, you touched the file last, so you *must* be experts on it, right? ;)
IBM MCA SCSI: Version 4.0b-ac
IBM MCA SCSI: IBM SCSI-2 F/W Adapter found, io=0x3540, scsi id=7,
ROM Addr.=off,<7> port-offset=0x0, subsystem=enabled.
IBM MCA SCSI: Control Register contents: 3, status: 4 IBM MCA SCSI: This adapters' POS-registers: fc 8e f1 ec 3c c7 0 ff IBM MCA SCSI: SCSI-Cache bits: 1111111111111111
IBM MCA SCSI: SCSI-Retry bits: 0000000000000000
IBM MCA SCSI: Separate bus mode (wide-addressing enabled) IBM MCA SCSI: Sync.-Rate (F/W: 20, Int.: 10, Ext.: 5.00) MBytes/s IBM MCA SCSI: Current SCSI-host index: 0
IBM MCA SCSI: Removing default logical SCSI-device mapping................
IBM MCA SCSI: Scanning SCSI-devices............................................. IBM MCA SCSI: Mapping SCSI-devices.................
IBM MCA SCSI: Device order: IBM/ANSI (pun=7 is first). IBM MCA SCSI: Determined SCSI-device-mapping:
Physical SCSI-Device Map Logical SCSI-Device Map
ID\LUN 0 1 2 3 4 5 6 7 ID\LUN 0 1 2 3 4 5 6 7
0 - - - - - - - - 0 0 - - - - - - -
1 - - - - - - - - 1 1 - - - - - - -
2 D + + + + + + + 2 2 - - - - - - -
3 - - - - - - - - 3 3 - - - - - - -
4 - - - - - - - - 4 4 - - - - - - -
5 - - - - - - - - 5 5 - - - - - - -
6 - - - - - - - - 6 6 - - - - - - -
7 A A A A A A A A 7 f f f f f f f f
8 - - - - - - - - 8 7 - - - - - - -
9 - - - - - - - - 9 8 - - - - - - -
10 - - - - - - - - 10 9 - - - - - - -
11 - - - - - - - - 11 a - - - - - - -
12 - - - - - - - - 12 b - - - - - - -
13 - - - - - - - - 13 c - - - - - - -
14 - - - - - - - - 14 d - - - - - - -
15 - - - - - - - - 15 e - - - - - - -
scsi0 : IBM SCSI-Subsystem
issue scsi cmd=12 to ldn=2
IBM MCA SCSI: Fatal Subsystem ERROR!
Last cmd=0x12, ena=f600, len=36/8,Blocksize=0,host=c3d0c000, ldn2
Blockcount=0/0
Logical block=0/0
Reason given: COMMAND ERROR
IBM MCA SCSI: Subsystem Error-Status follows:
Command Type................: 30
Attention Register..........: e2
Basic Control Register......: 3
Interrupt Status Register...: e2
Basic Status Register.......: 4
SCB-Command.................: 1c0b
SCB-Enable..................: f600
SCB-logical block address...: 0
SCB-system buffer address...: 3d0c614
SCB-system buffer length....: 8
SCB-tsb address.............: 3d0c5f8
SCB-Chain address...........: 0
SCB-block count.............: 0
SCB-block length............: 0
Send this report to the maintainer.
Kernel panic - not syncing: IBM MCA SCSI: Fatal error message from the subsyste!Pid: 0, comm: swapper Not tainted 2.6.30-rc7 #4
Call Trace: [<c0115f8e>] ? panic+0x3e/0x100 [<c0284725>] ? interrupt_handler+0x3a5/0x810 [<c013111a>] ? handle_IRQ_event+0x2a/0xb0 [<c0132707>] ? handle_level_irq+0x47/0x90 [<c0104377>] ? handle_irq+0x17/0x20 [<c010431c>] ? do_IRQ+0x2c/0x70 [<c0103009>] ? common_interrupt+0x29/0x30 [<c0101ba7>] ? cpu_idle+0x17/0x40 [<c04229d6>] ? start_kernel+0x206/0x240
Rebooting in 60 seconds..
-- Dave
Quoted 5 lines · On Thu, 23 Jul 2009 20:34:24 -0700 Dave Hansen <[email protected]> wrote:
No, this isn't a joke. I actually still have an IBM 9595, and I've been running 2.4 on it all this time. A friend of mine tried to upgrade one to 2.6 and couldn't get it to boot. I managed to get a bit of serial console output of the error it is throwing. I don't speak SCSI very well, so I'm hoping that you guys might have some insight.
Not a lot - the SCSI adapter in question is more of a smart controller and I suspect the trap is because it was fed junk (eg invalid sg lists). I doubt it gets tested very much somehow.