Skip to contentSkip to conversation

b43: Add LP PHY Analog Switch Support

PATCH In review Thomas Ilnseher 2 participants 2 messages Sep 14, 2009 Networking drivers (wireless)

lore
Share & tools
lore
#0 lore raw

PATCH 1/1 b43: Add LP PHY Analog Switch Support

The current verison of b43 uses "b43_phyop_switch_analog_generic" for A, G and LP phys.

According to the spec, this is the wrong behaviour for the LP PHY (see: http://bcm-v4.sipsolutions.net/802.11/PHY/Anacore )

While no problems on the x86 plattform where seen, this leads to a crash on the BCM5354 SoC (MIPS 32 LE plattform).
This patch implements the analog switch for LP PHYs according to the specs. It fixes the crash

---
diff -uNr b/drivers/net/wireless/b43/phy_lp.c
a/drivers/net/wireless/b43/phy_lp.c

drivers/net/wireless/b43/phy_lp.c 2009-09-14 21:03:15.158507573 +0200 renamed from drivers/net/wireless/b43/phy_lp.c 2009-09-14 06:14:18.000000000 +0200 +11 -1
@@ -2228,6 +2228,16 @@
        return B43_TXPWR_RES_DONE;
 }
 
+void b43_lpphy_op_switch_analog(struct b43_wldev *dev, bool on)
+{
+       if (on) {
+               b43_phy_mask(dev, B43_LPPHY_AFE_CTL_OVR, 0xfff8);
+       } else {
+               b43_phy_set(dev, B43_LPPHY_AFE_CTL_OVRVAL, 0x0007);
+               b43_phy_set(dev, B43_LPPHY_AFE_CTL_OVR, 0x0007);
+       }
+}
+
 const struct b43_phy_operations b43_phyops_lp = {
        .allocate               = b43_lpphy_op_allocate,
        .free                   = b43_lpphy_op_free,
@@ -2239,7 +2249,7 @@
        .radio_read             = b43_lpphy_op_radio_read,
        .radio_write            = b43_lpphy_op_radio_write,
        .software_rfkill        = b43_lpphy_op_software_rfkill,
-       .switch_analog          = b43_phyop_switch_analog_generic,
+       .switch_analog          = b43_lpphy_op_switch_analog,
        .switch_channel         = b43_lpphy_op_switch_channel,
        .get_default_chan       = b43_lpphy_op_get_default_chan,
        .set_rx_antenna         = b43_lpphy_op_set_rx_antenna,
#1 lore raw
Quoted 36 lines · On Monday 14 September 2009 23:01:33 Thomas Ilnseher wrote:

The current verison of b43 uses "b43_phyop_switch_analog_generic" for A, G and LP phys.

According to the spec, this is the wrong behaviour for the LP PHY (see: http://bcm-v4.sipsolutions.net/802.11/PHY/Anacore )

While no problems on the x86 plattform where seen, this leads to a crash on the BCM5354 SoC (MIPS 32 LE plattform).
This patch implements the analog switch for LP PHYs according to the specs. It fixes the crash

---
diff -uNr b/drivers/net/wireless/b43/phy_lp.c
a/drivers/net/wireless/b43/phy_lp.c

drivers/net/wireless/b43/phy_lp.c 2009-09-14 21:03:15.158507573 +0200 renamed from drivers/net/wireless/b43/phy_lp.c 2009-09-14 06:14:18.000000000 +0200 +10 -0
@@ -2228,6 +2228,16 @@
        return B43_TXPWR_RES_DONE;
 }
 
+void b43_lpphy_op_switch_analog(struct b43_wldev *dev, bool on)
+{
+       if (on) {
+               b43_phy_mask(dev, B43_LPPHY_AFE_CTL_OVR, 0xfff8);
+       } else {
+               b43_phy_set(dev, B43_LPPHY_AFE_CTL_OVRVAL, 0x0007);
+               b43_phy_set(dev, B43_LPPHY_AFE_CTL_OVR, 0x0007);
+       }
+}
+
 const struct b43_phy_operations b43_phyops_lp = {
        .allocate               = b43_lpphy_op_allocate,
        .free                   = b43_lpphy_op_free,

drivers/net/wireless/b43/phy_lp.c 2009-09-14 21:03:15.158507573 +0200 line 2255

Quoted 8 lines
drivers/net/wireless/b43/phy_lp.c 2009-09-14 21:03:15.158507573 +0200 renamed from drivers/net/wireless/b43/phy_lp.c 2009-09-14 06:14:18.000000000 +0200 +1 -1
@@ -2239,7 +2249,7 @@
        .radio_read             = b43_lpphy_op_radio_read,
        .radio_write            = b43_lpphy_op_radio_write,
        .software_rfkill        = b43_lpphy_op_software_rfkill,
-       .switch_analog          = b43_phyop_switch_analog_generic,
+       .switch_analog          = b43_lpphy_op_switch_analog,
        .switch_channel         = b43_lpphy_op_switch_channel,
        .get_default_chan       = b43_lpphy_op_get_default_chan,
        .set_rx_antenna         = b43_lpphy_op_set_rx_antenna,

ack

Signature · 1 line
Greetings, Michael.